Poly(ether amine) and cross-linked poly(propylene oxide) diacrylate thin-film polymer electrolyte for 3D-microbatteries

This paper presents a novel thin-film electrolyte of a 2:1 blend of polyetheramine (glyceryl poly(oxypropylene)) and cross-linked oligomeric poly(propylene oxide) diacrylate with LiTFSI. The polyetheramine acts as a surfactant, and can thereby be applied as a conformal coating on complex surfaces—here demonstrated for porous LiFePO₄ cathodes—making it useful for 3D-microbatteries. The poly(propylene oxide) diacrylate blends with the surfactant and is easily UV cross-linked, thereby ensuring good mechanical stability. Electrolytes, ~ 2 μm thick, were casted onto LiFePO₄ cathodes and cycled against metallic lithium, displaying stable discharge capacities of ~ 8 mAh/g at room temperature and ~ 120 mAh/g at 60 °C. The electrolyte showed conductivities of 3.45 × 10^? 6 and 5.80 × 10^? 5 S cm^? 1 at room temperature and 60 °C, respectively.     

Enhanced electrical conductivity in Ce0.79Gd0.20Co0.01O2−δ for low temperature solid oxide fuel cell applications

Very high electrical conductivity of ～0.021 S/cm at 600 °C is obtained in Ce_0.79Gd_0.20Co_0.01O_2?δ. Corresponding activation energy of conduction ～0.43 eV measured in the temperature range of 400–700 °C is found to be notably low. Improved electrical properties with 99% of the theoretical density as obtained for these specimens, prepared using powder of average particle size ～20 nm and subsequent sintering at 1100 °C, is considered to be a significant step to reduce the processing temperature. The measured electrical potential of ～1 V indicates the suitability of its use as an electrolyte in electrochemical devices.     

Phase transitions of CaTiO3 ceramics sintered with the aid of NaF and MgF2

New phases with initial composition (1 ? x)CaTiO₃ ? xNaF ? xMgF₂ (0 ≤ x ≤ 0.20) have been prepared at low temperature (950 °C) from mixtures of CaTiO₃ and fluorides NaF and MgF₂. The oxyfluorides obtained have been characterized by X-ray diffraction at room temperature and indexed by isotypy with orthorhombic CaTiO₃. The microstructures of these phases are observed by scanning electron microscopy. Dielectric measurements have been carried out during cooling cycle from 500 °C to room temperature at two frequencies (100 Hz, 1 kHz). Differential scanning calorimetry (DSC), thermogravimetry (TG) and differential thermogravimetry (DTG) analyses have been performed, respectively, from room temperature up to 550 °C (DSC) and 920 °C (TG–DTG). The dielectric measurements revealed two anomalies which have been confirmed by DSC analyses. These phenomena are ascribed to second order phase transitions. The variation of the real permittivity with temperature is in agreement with the class I capacitor specifications. However, the dielectric losses have to be improved.     

Electrochemical characterisation of MBaCo3ZnO7+δ (M = Y,Er, Tb) as SOFC cathode material with low thermal expansion coefficient

The electrochemical oxygen activation at high temperature was studied on a new class of oxygen-store material based on the system YBaCo₄O_7+δ. Three different porous layers made of YBaCo₃ZnO_7+δ, ErBaCo₃ZnO_7+δ and TbBaCo₃ZnO_7+δ were electrochemically tested as oxygen activation coatings and showed a very promising activity. The envisaged applications for these materials are principally as SOFC cathodes and as catalytic layer on oxygen membranes. The electrochemical performance followed the order Tb ? Y > Er at any tested temperature. Area specific resistance for the best performing material (TbBaCo₃ZnO_7+δ) ranges from 30 mΩ cm² at 850 °C to 0.46 Ω cm² at 650 °C. High temperature XRD showed that the thermal expansion coefficient (25–900 °C) in air of TbBaCo₃ZnO₇ is 9.45 × 10^?6 K^?1, which evidences the good thermochemical compatibility of this cobalt-rich electrocatalyst with YSZ/GDC electrolytes.     

Synthesis and characterization of LiCo3/5Mn2/5VO4 ceramics

Dielectric and a.c. conductivity properties of LiCo_3/5Mn_2/5VO₄ ceramic are investigated. This compound is prepared by solution-based chemical method and the formation is checked by X-ray diffraction (XRD) study. XRD analysis at room temperature shows an orthorhombic phase. Frequency dependence of dielectric constant (?_r) at different temperatures shows a dispersive behavior at low frequencies. Temperature dependence of ?_r at different frequencies indicates the transition temperature (T_c) = 235 °C, 245 °C, 257 °C and 265 °C with (?_r)_max. ～3689, 1373, 750 and 386 for 10, 50, 100 and 200 kHz respectively. A.c. conductivity analysis indicates that electrical conduction in the material is a thermally activated process.     

Dyed polyvinyl chloride films for use as high-dose routine dosimeters in radiation processing

Characteristics of the polyvinyl chloride (PVC) films containing 0.11 wt% of malachite green oxalate or 6GX-setoglausine and about 100 μm in thickness were studied for use as routine dosimeters in radiation processing. These films show basically color bleaching under irradiation with ⁶⁰Co γ-rays in a dose range of 5–50 kGy. The sensitivity of the dosimeters and the linearity of dose-response curves are improved by adding 2.5% of chloral hydrate [CCl₃CH(OH)₂] and 0.15% hydroquinone [HOC₆H₄OH]. These additions extend the minimum dose limit to 1 kGy covering dosimetry requirements of the quality assurance in radiation processing of food and healthcare products. The dose responses of both dyed PVC films at irradiation temperatures from 20°C to 35°C are constant relative to those at 25°C, and the temperature coefficients for irradiation temperatures from 35°C to 55°C were estimated to be (0.43±0.01)%/°C. The dosimeter characteristics are stable within 1% at 25°C before and 60 days after the end of irradiation.     

Temperature effect on the chemical composition of a polytetrafluoroethylene surface under the irradiation of synchrotron radiation by means of the X-ray photoelectron spectroscopy

The chemical composition and components of a polytetrafluoroethylene (PTFE) surface was investigated as a function of the temperature under the irradiation of synchrotron radiation (SR) by the X-ray photoelectron spectroscopy (XPS). When the temperature of PTFE under the SR irradiation was less than 100 °C, the C-rich surface appeared. With increasing the temperature more than 150 °C, the relative intensity of the F 1s peak to the C 1s peak increased markedly. At the temperatures of 150–180 °C, the C–C component became small and the CF₂ component was dominant. With further increasing the temperature more than 200 °C, CF₃, CF and C–CF components grew in addition to CF₂ component. Based on these XPS results, the temperature effect on the chemical composition and components is discussed.     

Molecular characterization of Ulex europaeus biochar obtained from laboratory heat treatment experiments – A pyrolysis–GC/MS study

Gorse species (Ulex sp.) are ubiquitous in the shrublands of NW Spain and have the potential to become key players in an integral biofuel/biochar program in NW Spain. Here we present molecular characterization (using pyrolysis–GC/MS) of a biochar “thermosequence” obtained by laboratory heating of Ulex europaeus wood in a muffle furnace between 200 and 600 °C (T_CHAR). Low temperature chars (T_CHAR ≤ 350 °C) produced significant amounts of pyrolysis products of which the precursor biopolymer could be recognized, while high-temperature chars (T_CHAR ≥ 400 °C) produced mainly phenols and monocyclic and polycyclic aromatic hydrocarbons, which are not specific for any biopolymer. Carbohydrate could hardly be recognized at T_CHAR ≥ 350 °C. The thermal rearrangement of polyphenols, mainly lignin, was reflected in more detail (1) C₃-side chain shortening and probably depolymerization (T_CHAR 200–350 °C), (2) demethoxylation of syringyl and probably also some guaiacyl lignin (T_CHAR 300–400 °C), (3) elimination of virtually all remaining methoxyl groups (T_CHAR 350–400 °C), through dehydroxylation and demethoxylation, (4) almost complete dehydroxylation of lignin and other biopolymers (T_CHAR 400–500 °C), (5) progressive condensation into polyaromatic structures (T_CHAR 300–500 °C) and (6) partial elimination of alkyl bridges between (poly)aromatic moieties (T_CHAR 450–500 °C). These results were supported by Fourier transform infrared spectroscopy (FTIR) of the same samples. We conclude that pyrolysis–GC/MS can be used as a rapid molecular screening method of gorse-derived biochar. Molecular properties elucidation is an essential part of predicting the stability and agronomical behavior of gorse-derived biochar after future implementation in soils.     

Evaluation of the porous structure development of chars from pyrolysis of rice straw: Effects of pyrolysis temperature and heating rate

The effects of pyrolysis temperature and heating rate on the porous structure characteristics of rice straw chars were investigated. The pyrolysis was done at atmospheric pressure and at temperatures ranging from 600 to 1000 °C under low heating rate (LHR) and high heating rates (HHR) conditions. The chars were characterized by ultimate analysis, field emission scanning electron microscope (FESEM), helium density measurement and N₂ physisorption method. The results showed that temperature had obvious influence on the char porous characteristics. The char yield decreased by approximately 16% with increasing temperature from 600 to 1000 °C. The carbon structure shrinkage and pore narrowing occurred above 600 °C. The shrinkage of carbon skeleton increased by more than 22% with temperatures rising from 600 to 1000 °C. At HHR condition, progressive increases in porosity development with increasing pyrolysis temperature occurred, whereas a maximum porosity development appeared at 900 °C. The total surface area (S_total) and micropore surface area (S_micro) reached maximum values of 30.94 and 21.81 m²/g at 900 °C and decreased slightly at higher temperatures. The influence of heating rate on S_total and S_micro was less significant than that of pyrolysis temperature. The pore surface fractal dimension and average pore diameter showed a good linear relationship.     

Influence of sintering temperature on microstructure,critical current density and pinning potential of superconducting Bi1.6Pb0.5Sr1.8Dy0.2Ca1.1Cu2.1O8+δ ceramics

The influence of sintering temperature on the microstructure, critical current density (J_C), pinning potential values (U₀) and flux pinning properties of Bi_1.6Pb_0.5Sr_1.8Dy_0.2Ca_1.1Cu_2.1O_8+δ superconductor has been investigated. The samples are prepared by the solid-state route and sintered at temperatures ranging from 846 to 860 °C. A systematic correlation between the sintering temperature, Lotgering index, J_C, U₀ and flux pinning properties has been found. The samples sintered at lower sintering temperature (846 °C) have more grain boundaries with smaller grains while those sintered at a higher temperature (856 °C) contain larger grains with good texturing. The flux pinning force (F_P) calculated from the field dependent J_C values shows that the irreversibility lines (IL) of the Dy-doped samples shift towards higher fields to different extents depending on the sintering temperature. The maximum value of F_P = 1697 kN m^?3 is obtained for the sample sintered at 846 °C and the peak position of F_P is obtained at 0.96 T as against 616 kN m^?3 and 0.52 T for the sample sintered at 856 °C. The U₀ values calculated by Anderson's function is maximum for the sample sintered at 846 °C. But the self-field J_C value of this sample is lower than that of the samples sintered at 856 °C. The samples sintered at 856 °C show best self-field J_C due to the improved microstructure. The changes in microstructure followed by very high enhancement of self-field J_C, J_C(B) characteristics, F_P and U₀ values within a narrow temperature range, are of great scientific and technological significance and the results are explained on the basis of microstructural variation with respect to sintering temperature, hole optimization and formation of point defects due to the doping of Dy atoms in Bi_1.6Pb_0.5Sr_1.8Dy_0.2Ca_1.1Cu_2.1O_8+δ system.     

Effects of calcination and activation temperature on dry reforming catalysts

The effect of calcination temperatures on dry reforming catalysts supported on high surface area alumina Ni/γ-Al₂O₃ (SA-6175) was studied experimentally. In this study, the prepared catalyst was tested in a micro tubular reactor using temperature ranges of 500, 600, 700 and 800 °C at atmospheric pressure, using a total flow rate of 33 ml/min consisting of 3 ml/min of N₂, 15 ml/min of CO₂ and 15 ml/min of CH₄. The calcination was carried out in the range of 500–900 °C. The catalyst is activated inside the reactor at 500–800 °C using hydrogen gas. It was observed that calcination enhances catalyst activity which increases as calcination and reaction temperatures were increased. The highest conversion was obtained at 800 °C reaction temperature by using catalyst calcined at 900 °C and activation at 700 °C. The catalyst characterization conducted supported the observed experimental results.     

Rheological,morphological, thermal,and mechanical properties of blends of vectra A950 and poly(trimethylene terephthalate): A study on a high-viscosity-ratio system

Poly(trimethylene terephthalate) (PTT) and a liquid crystalline polymer, Vectra A950 (VA), were melt-blended and subjected to capillary rheometry. Effects of VA content, shear rate and temperature on viscosity and flow activation energy (E_a) were investigated. Partial fibrillation was found even though the viscosity ratio was greater than one, leading to the formation of in-situ composites. Thermal and thermogravimetric analysis of the blends suggested that they were immiscible and their thermal stabilities were enhanced. From tensile tests, the incorporation of VA improved tensile modulus, slightly decreased tensile strength, and drastically lowered elongation at break, compared to neat PTT. It was found that the blend with the best VA dispersion can be achieved at the minimum VA content (10 wt%) and lowest processing temperature (250 °C). Not only did this blend exhibit improved mechanical properties comparable to those of blends processed at temperatures closer to the crystalline-to-nematic transition of VA (～280 °C), it also shows enhanced processibility through the reduction of both melt viscosity and E_a.     

Electrode properties of Sr doped La2CuO4 as new cathode material for intermediate-temperature SOFCs

High performance La_2−xSr_xCuO_4−δ (x = 0.1, 0.3, 0.5) cathode materials for intermediate temperature solid oxide fuel cell (IT-SOFCs) were prepared and characterized. The investigation of electrical properties indicated that La_1.7Sr_0.3CuO₄ cathode has low area specific resistance (ASR) of 0.16 Ω cm² at 700 °C and 1.2 Ω cm² at 500 °C in air. The rate-limiting step for oxygen reduction reaction on La_1.7Sr_0.3CuO₄ electrode changed with oxygen partial pressure and measurement temperature. La_1.7Sr_0.3CuO₄ cathode exhibits the lowest overpotential of about 100 mV at a current density of 150 mA cm⁻² at 700 °C in air.     

Quantitative and kinetic TG-FTIR study of biomass residue pyrolysis: Dry distiller's grains with solubles (DDGS) and chicken manure

New energy policies all over the world are trying to tackle high oil prices and climate change by promoting the use of biomass to produce heat, electricity and liquid transportation fuels. In this paper we studied two different secondary fuels: dry distiller's grains with solubles (DDGS) and chicken manure. These materials have high content of nitrogen and ashes which limit their usage in thermal applications due to potential excessive NO_x emissions and problems of slagging, fouling, corrosion and loss of fluidization.The fuels tested here were received from industrial partners. In order to reduce the ash content the fuels were pre-treated using water leaching pre-treatment.Pyrolysis of these fuels has been monitored through a TG-FTIR set-up. Quantification of the following volatile species was possible: CO, CO₂, CH₄, HCN, NH₃, HNCO, H₂O.The water leaching appeared to decrease the amount of ashes in both samples and remove some of the troublesome compounds like Cl, S and K.The DDGS thermogravimetric curve showed three main peaks at 280 °C, 330 °C and 402 °C with a total weight loss of around 79%wt_a.r. (on an “as received” basis). NH₃ is the main N-compound released at low temperatures with a peak at 319 °C. HNCO and HCN were detected at higher temperatures of around 400 °C. Chicken manure reacted in four stages with peaks at 280 °C, 324 °C, 430 °C and 472 °C with a total average weight loss of 66%wt_a.r. The main N-compound was HNCO, released at 430 °C. Ammonia was detected during the whole measurement, while HCN presented peaks of reactivity at 430 °C and 472 °C.Kinetic analysis was applied using a distributed activation energy method (DAEM) using discrete and Gaussian distributions and data for further modeling purposes were retrieved and presented.     

Cobalt-free cathode material SrFe0.9Nb0.1O3−δ for intermediate-temperature solid oxide fuel cells

A cobalt-free cubic perovskite oxide, SrFe_0.9Nb_0.1O_3?δ (SFN) was investigated as a cathode for intermediate-temperature solid oxide fuel cells (IT-SOFCs). XRD results showed that SFN cathode was chemically compatible with the electrolyte Sm_0.2Ce_0.8O_1.9 (SDC) for temperatures up to 1050 °C. The electrical conductivity of SFN sample reached 34–70 S cm^?1 in the commonly operated temperatures of IT-SOFCs (600–800 °C). The area specific resistance was 0.138 Ω cm² for SFN cathode on SDC electrolyte at 750 °C. A maximum power density of 407 mW cm^?2 was obtained at 800 °C for single-cell with 300 μm thick SDC electrolyte and SFN cathode.     

Nonstoichiometry,point defects and magnetic properties in Sr2FeMoO6−δ double perovskites

The phase stability, nonstoichiometry and point defect chemistry of polycrystalline Sr₂FeMoO_6?δ (SFMO) was studied by thermogravimety at 1000, 1100, and 1200 °C. Single-phase SFMO exists between ?10.2≤log pO₂≤?13.7 at 1200 °C. At lower oxygen partial pressure a mass loss signals reductive decomposition. At higher pO₂ a mass gain indicates oxidative decomposition into SrMoO₄ and SrFeO_3?x. The nonstoichiometry δ at 1000, 1100, and 1200 °C was determined as function of pO₂. SFMO is almost stoichiometric at the upper phase boundary (e.g. δ=0.006 at 1200 °C and log pO₂=?10.2) and becomes more defective with decreasing oxygen partial pressure (e.g. δ=0.085 at 1200 °C and log pO₂=?13.5). Oxygen vacancies are shown to represent majority defects. From the temperature dependence of the oxygen vacancy concentration the defect formation enthalpy was estimated (ΔH_OV=253±8 kJ/mol). Samples of different nonstoichiometry δ were prepared by quenching from 1200 °C at various pO₂. An increase of the unit cell volume with increasing defect concentration δ was found. The saturation magnetization is reduced with increasing nonstoichiometry δ. This demonstrates that in addition to Fe/Mo site disorder, oxygen nonstoichiometry is another source of reduced magnetization values.     

Preparation via microemulsion method and proton conduction at intermediate-temperature of BaCe1−xYxO3−α

The ceramic powders of BaCe_1?xY_xO_3?α (x = 0.05, 0.10, 0.15, 0.20) have been prepared via a microemulsion method. Green compacts of the powders were sintered to densities higher than 95% of theoretical at the lower temperature (1500 °C). The obtained ceramics showed a single-phase of orthorhombic perovskite. The proton conduction was investigated by employing the techniques of AC impedance and electrochemical hydrogen permeation (hydrogen pumping) at 300–600 °C. It was found that the ceramics were almost pure proton conductors in wet hydrogen, and the highest proton conductivity was observed for x = 0.15 at 600 °C. Ammonia was synthesized successfully from nitrogen and hydrogen at atmospheric pressure in the electrolytic cell using BaCe_0.85Y_0.15O_3?α. The maximum rate of NH₃ formation was found to be 2.1 × 10^?9 mol s^?1 cm^?2 at 500 °C with an applied current of 0.75 mA.     

Synthesis and properties of the compound: LiNi3/5Cu2/5VO4

The LiNi_3/5Cu_2/5VO₄ is synthesized by solution-based chemical method and its formation has been checked by X-ray diffraction (XRD) study. XRD study shows a tetragonal unit cell structure with lattice parameters of a = 11.6475 (18) Å, c = 2.4855 (18) Å and c/a = 0.2134 Å. Electrical properties are verified using complex impedance spectroscopy (CIS) technique. Complex impedance analysis reveals following points: (i) the bulk contribution to electrical properties up to 200 °C, (ii) the bulk and grain boundary contribution at T ≥ 225 °C, (iii) the presence of temperature dependent electrical relaxation phenomena in the material. D.c. conductivity study indicates that electrical conduction in the material is a thermally activated process.     

Fabrication and magnetic properties of electrospun copper ferrite (CuFe2O4) nanofibers

Tetragonal copper ferrite (CuFe₂O₄) nanofibers were fabricated by electrospinning method using a solution that contained poly(vinyl pyrrolidone) (PVP) and Cu and Fe nitrates as alternative metal sources. The as-spun and calcined CuFe₂O₄/PVP composite samples were characterized by TG-DTA, X-ray diffraction, FT-IR, and SEM, respectively. After calcination of the as-spun CuFe₂O₄/PVP composite nanofibers (fiber size of 89 ± 12 nm in diameter) at 500 °C in air for 2 h, CuFe₂O₄ nanofibers of 66 ± 13 nm in diameter having well-developed tetragonal structure were successfully obtained. The crystal structure and morphology of the nanofibers were influenced by the calcination temperature. After calcination at 600 and 700 °C, the nature of nanofibers changed which was possibly due to the reorganization of the CuFe₂O₄ structure at high temperature, and a fiber structure of packed particles or crystallites was prominent. Crystallite size of the nanoparticles contained in nanofibers increases from 7.9 to 23.98 nm with increasing calcination temperature between 500 and 700 °C. Room temperature magnetization results showed a ferromagnetic behavior of the calcined CuFe₂O₄ samples, having their specific saturation magnetization (M_s) values of 17.73, 20.52, and 23.98 emu/g for the samples calcined at 500, 600, and 700 °C, respectively.     

The thioantimonate anion [Sb4S8]4− acting as a tetradentate ligand: Solvothermal synthesis,crystal structure and properties of {[In(C6H14N2)2]2Sb4S8}Cl2 exhibiting unusual uniaxial negative and biaxial positive thermal expansion

The new compound {[In(C₆H₁₄N₂)₂]₂Sb₄S₈}Cl₂ was prepared under solvothermal conditions reacting InCl₃, Sb and S using 1,2-trans-diaminocyclohexane as solvent and structure directing molecule. The compound crystallizes in the monoclinic space group C2/c with a = 29.0259(12), b = 6.7896(2), c = 24.2023(12) Å, β = 99.524(4)°, V = 4703.9(3) ų. The central structural motif is the thioantimonate(III) anion [Sb₄S₈]^4? acting as a tetradentate ligand thus joining two symmetry related In³⁺ centered complexes. This binding mode was never observed before for the [Sb₄S₈]^4? anion. The optical band gap was determined as 2.03 eV in agreement with the red color of the compound. The thermal decomposition was monitored with in-situ X-ray diffraction experiments. After the emission of the amine molecules an amorphous intermediate is formed followed by the crystallization of InSbS₃ which is stable up to about 590 °C. On further heating, InSbS₃ is destroyed and reflections of γ-In₂S₃ appear being contaminated with some elemental Sb. Temperature dependent in-situ X-ray powder diffractometry performed between 30 and 220 °C reveals an unusual reversible negative and positive thermal expansion. The decrease of the a-axis in the temperature range is about 0.74 Å and the increase of the c-axis ca. 0.54 Å. Interestingly, the b-axis exhibits also a thermal expansion, i.e., a biaxial positive and an uniaxial negative thermal expansion coexist which is very unusual. The relative negative expansion coefficients for the a-axis of ?194 × 10^?6K^?1 (30–120 °C) and ?82 × 10^?6K^?1 (120–220 °C) are in the region of so-called colossal thermal expansion.