Determination of residual levels of unsaturation in partially hydrogenated poly(2,3-diphenyl-1,3-butadiene) using TG

The thermal degradation characteristics of head-to-head poly(styrene) [HHPS] should provide insight with respect to the impact of head-to-head placement on the thermal stability of traditional atactic head-to-tail polymer [HTPS]. The synthesis of head-to-head poly(styrene) must be accomplished indirectly. The head-to-head polymer is most satisfactorily obtained by dissolving metal reduction of poly(2,3-diphenyl-1,3-butadiene) [PDBD] generated by radical polymerization of the corresponding diene monomer. Full saturation of the polymer mainchain requires several iterations of the reduction procedure. Since the decomposition of poly(2,3-diphenyl-1,3-butadiene) is prominent at 374°C and that for head-to-head poly(styrene) is similarly facile at 406°C, it seemed feasible that TG of partially hydrogenated PDBD might be utilized as a convenient means of monitoring the extent of hydrogenation. This has been demonstrated for various levels of unsaturation remaining - from approximately 90 to less than 10%. Within this range the peak areas from the DTG plots of the partially hydrogenated polymer provide a good reflection of the ratio of unsaturated to saturated units in the polymer. Even low levels of unsaturation in the polymer may be detected by the asymmetry of the decomposition peak for the polymer. This revised version was published online in August 2006 with corrections to the Cover Date.     

TEMPO addition into pre-irradiated fluoropolymers and living-radical graft polymerization of styrene for preparation of polymer electrolyte membranes

We prepared proton exchange membranes (PEMs) by 2,2,6,6-tetramethylpiperidinyl-1-oxy (TEMPO)-mediated living-radical graft polymerization (LRGP) of styrene into fluoropolymer films and subsequent sulfonation. Poly(vinylidene fluoride) (PVDF) and poly(ethylene-co-tetrafluoroethylene) (ETFE) films were first irradiated and then treated with TEMPO solutions in various solvents. TEMPO addition was confirmed by the test of styrene grafting into TEMPO-treated films at 60 °C, at which the LRGP never proceeds. This test enabled us to differentiate the LRGP from the conventional graft polymerization. In order to gain a deep insight about TEMPO-addition reaction, the TEMPO-penetration behavior into the base polymer films was examined by a permeation experiment and computer simulation. Xylene and dioxane were appropriate solvents for the complete introduction of TEMPO into PVDF and ETFE films, respectively. Then, the LRGP of styrene was performed based on the fully TEMPO-capped films at 125 °C with various solvents. By using an alcoholic solvent, the degree of grafting was enhanced and it reached a maximum of 38%. This grafted film was sulfonated to prepare a PEM showing an ion exchange capacity of 2.2 meq/g and proton conductivity of 1.6×10^?1 S/cm.     

Proton transport properties of poly(aspartic acid) with different average molecular weights

We synthesized seven partially protonated poly(aspartic acids)/sodium polyaspartates (P-Asp) with different average molecular weights to study their proton transport properties. The number-average degree of polymerization (DP) for each P-Asp was 30 (P-Asp30), 115 (P-Asp115), 140 (P-Asp140), 160 (P-Asp160), 185 (P-Asp185), 205 (P-Asp205), and 250 (P-Asp250). The proton conductivity depended on the number-average DP. The maximum and minimum proton conductivities under a relative humidity of 70% and 298 K were 1.7 · 10^?3 S cm^?1 (P-Asp140) and 4.6 · 10^?4 S cm^?1 (P-Asp250), respectively. Differential thermogravimetric analysis (TG-DTA) was carried out for each P-Asp. The results were classified into two categories. One exhibited two endothermic peaks between t = (270 and 300) °C, the other exhibited only one peak. The P-Asp group with two endothermic peaks exhibited high proton conductivity. The high proton conductivity is related to the stability of the polymer. The number-average molecular weight also contributed to the stability of the polymer.     

Pyrolysis of textile wastes: I. Kinetics and yields

Thermal behavior of textile waste was studied by thermogravimetry at different heating rates and also by semi-batch pyrolysis. It was shown that the onset temperature of mass loss is within 104–156 °C and the final reaction temperature is within 423–500 °C. The average mass loss is 89.5%. There are three DTG peaks located at the temperature ranges of 135–309, 276–394 and 374–500 °C, respectively. The first two might be associated with either with decomposition of the hemicellulose and cellulose or with different processes of cellulose decomposition. The third peak is possibly associated to a synthetic polymer. At a temperature of 460 °C, the expected amount of volatiles of this waste is within 85–89%. The kinetic parameters of the individual degradation processes were determined by using a parallel model. Their dependence on the heating rate was also established. The pyrolysis rate is considered as the sum of the three reaction rates. The pyrolysis in a batch reactor at 700 °C and nitrogen flow of 60 ml/min produces 72 wt.% of oil, 13.5 wt.% of gas and 12.5 wt.% of char. The kinetic parameters of the first peak do not vary with heating rate, while those of the second and the third peak increase and decrease, respectively, with an increasing heating rate, proving the existence of complex reaction mechanisms for both cases.     

Thermal behaviour of malonic acid,sodium malonate and its compounds with some bivalent transition metal ions

Characterization, thermal stability and thermal decomposition of transition metal malonates, MCH₂C₂O₄·nH₂O (M = Mn(II), Fe(II), Co(II), Ni(II), Cu(II), Zn(II)), as well as, the thermal behaviour of malonic acid (C₃H₄O₄) and its sodium salt (Na₂CH₂C₂O₄·H₂O) were investigated employing simultaneous thermogravimetry and differential thermal analysis (TG-DTA), differential scanning calorimetry (DSC), infrared spectroscopy, TG-FTIR system, elemental analysis and complexometry. The dehydration, as well as, the thermal decomposition of the anhydrous compounds occurs in a single step. For the sodium malonate the final residue up to 700 °C is sodium carbonate, while the transition metal malonates the final residue up to 335 °C (Mn), 400 °C (Fe), 340 °C (Co), 350 °C (Ni), 520 °C (Cu) and 450 °C (Zn) is Mn₃O₄, Fe₂O₃, Co₃O₄, NiO, CuO and ZnO, respectively. The results also provided information concerning the ligand's denticity, thermal behaviour and identification of some gaseous products evolved during the thermal decomposition of these compounds.     

The electrochemical properties of thermophilic cytochrome P450 CYP119A2 at extremely high temperatures in poly(ethylene oxide)

The electrochemical measurements were carried out by using thermophilic cytochrome P450 CYP119A2 (P450st) modified with poly(ethylene oxide) (PEO) in PEO₂₀₀ as an electrochemical solvent. The PEO modified P450st gave clear reduction–oxidation peaks by cyclic voltammetry in oxygen-free PEO₂₀₀ up to 120 °C. The midpoint potential measured for the P450st was −120 mV vs. [Fe(CN)₆]⁴⁻/[Fe(CN)₆]³⁻ at 120 °C. The peak separation, ΔE, was 16 mV at 100 mV/s. The estimated electron transfer rate of PEO-P450st at 120 °C was 35.1 s⁻¹. The faster electron transfer reaction was achieved at higher temperatures. The electrochemical reduction of dioxygen was observed at 115 °C with the PEO-modified P450st system.     

Towards a combined use of Mn(Salen) and quaternary ammonium salts as catalysts for the direct conversion of styrene to styrene carbonate in the presence of dioxygen and carbon dioxide

The use of oxygen in combination with carbon dioxide to afford the direct conversion of alkenes into cyclic carbonates could help to promote the greenhouse gas while minimizing the impact of the oxidation reaction on the environment. In this work, we focused, for the first time, on the association of two catalytic systems individually efficient for the epoxidation of styrene (Mn(salen)/O₂ bubbling/isobutyraldehyde at 80 °C) and the cyclocarbonatation of styrene oxide (choline chloride/CO₂ at 15 bar and 120 °C). First, the feasibility of the cyclocarbonatation reaction, starting from the non-isolated epoxide, has been proven as styrene carbonate was formed with a 24% yield. The objective was, then, to determine the best conditions allowing the overall transformation in a common solvent. Taking into account the differences in optimal temperatures and kinetics of the two individual steps, it was decided to vary the temperature during the reaction [first 80 °C (3 h) and 120 °C (23 h)]. Under these conditions, styrene was converted into the epoxide but, unfortunately, styrene carbonate formation could not be demonstrated. Blank experiments have clearly shown that isobutyraldehyde, which is essential to the first step, must be completely consumed before the temperature rise. Otherwise, autoxidation of the aldehyde in the presence of styrene oxide at 120 °C leads to other products than styrene carbonate.     

Reduction of carbonyl compounds by Raney Ni–Al alloy and Al powder in the presence of noble metal catalysts in water

Raney Ni–Al alloy was found to be capable of reducing benzophenones to the corresponding diphenylmethanes (2) in water in good to excellent yields within 3 h at 60 °C in a sealed tube. The complete reduction process of both aromatic rings required 18 h at 80 °C with Raney Ni–Al and Al powder in the presence of Pt/C. The nature of the hydrogenated products was also found to greatly depend on temperature, reaction time, volume of water, and amount of Raney Ni–Al alloy being used.     

Studies of thermal decay of electropolymerized polypyrrole using in situ surface-enhanced Raman spectroscopy

In this work, the thermal degradation of polypyrrole (PPy) films was investigated by using in situ surface-enhanced Raman spectroscopy (SERS) for the first time. The results indicate that the decay of PPy in conductivity can be ascribed to the loss in oxidation degree and to the shorter conjugation length of PPy upon heating samples from 25 to 75 °C. Continuously raising the temperature of the sample from 75 to 125 °C results in serious decay. The oxidation degree of PPy is significantly decreased correspondingly. However, the peak assigned to the CC backbone stretching becomes broader due to the thermal decomposition of PPy. At temperatures of samples higher than 125 °C, PPy films lose their conducting properties and no characteristic peaks of oxidized PPy related to the oxidation degrees can be observed. Moreover, the peak of the CC backbone stretching completely disappear due to the complete decomposition of PPy.     

Synthesis and characterization of ZnO nanoparticles by thermal decomposition of a curcumin zinc complex

ZnO nanoparticles were generated by thermal decomposition of a binuclear zinc (II) curcumin complex as single source precursor. Thermal behavior of the precursor showed a considerable weight loss at about 374 °C by an exothermic reaction with a maximum weight loss rate of 14%/min. Complete decomposition of precursor was observed within 49 min with a heating rate of 10 °C/min. Synthesized nanoparticles have been characterized by X-ray diffraction, Fourier transform infrared spectroscopy, transmission electron microscopy and selected area electron diffraction microscopy. Results revealed monodispersed hexagonal zincite structure with an average size of 117 ± 4 nm.     

Thermal decomposition of lutetium propionate

The thermal decomposition of lutetium(III) propionate monohydrate (Lu(C₂H₅CO₂)₃·H₂O) in argon was studied by means of thermogravimetry, differential thermal analysis, IR-spectroscopy and X-ray diffraction. Dehydration takes place around 90 °C. It is followed by the decomposition of the anhydrous propionate to Lu₂O₂CO₃ with evolution of CO₂ and 3-pentanone (C₂H₅COC₂H₅) between 300 °C and 400 °C. The further decomposition of Lu₂O₂CO₃ to Lu₂O₃ is characterized by an intermediate constant mass plateau corresponding to a Lu₂O_2.5(CO₃)_0.5 overall composition and extending from approximately 550 °C to 720 °C. Full conversion to Lu₂O₃ is achieved at about 1000 °C. Whereas the temperatures and solid reaction products of the first two decomposition steps are similar to those previously reported for the thermal decomposition of lanthanum(III) propionate monohydrate, the final decomposition of the oxycarbonate to the rare-earth oxide proceeds in a different way, which is here reminiscent of the thermal decomposition path of Lu(C₃H₅O₂)·2CO(NH₂)₂·2H₂O.     

Ni–Al hydrotalcite-like material as the catalyst precursors for the dry reforming of methane at low temperature

Nickel–aluminium and magnesium–aluminium hydrotalcites were prepared by co-precipitation and subsequently submitted to calcination. The mixed oxides obtained from the thermal decomposition of the synthesized materials were characterized by XRD, H₂-TPR, N₂ sorption and elemental analysis and subsequently tested in the reaction of methane dry reforming (DRM) in the presence of excess of methane (CH₄/CO₂/Ar = 2/1/7). DMR in the presence of the nickel-containing hydrotalcite-derived material showed CH₄ and CO₂ conversions of ca. 50% at 550 °C. The high values of the H₂/CO molar ratio indicate that at 550 °C methane decomposition was strongly influencing the DRM process. The sample reduced at 900 °C showed better catalytic performance than the sample activated at 550 °C. The catalytic performance in isothermal conditions from 550 °C to 750 °C was also determined.     

Novel 1D coordination polymer {Tm(Piv)3}n: Synthesis,structure, magnetic properties and thermal behavior

The new 1D coordination polymer {Tm(Piv)₃}_n (1), where Piv=OOCBu^t?, was synthesized in high yield (>95%) by the reaction of thulium acetate with pivalic acid in air at 100 °С. According to the X-ray diffraction data, the metal atoms in compound 1 are in an octahedral ligand environment unusual for lanthanides. The magnetic and luminescence properties of polymer 1, it’s the solid-phase thermal decomposition in air and under argon, and the thermal behavior in the temperature range of ?50…+50 °С were investigated. The vaporization process of complex 1 was studied by the Knudsen effusion method combined with mass-spectrometric analysis of the gas-phase composition in the temperature range of 570–680 K.     

Macro- and microporous carbon monoliths with high surface areas pyrolyzed from poly(divinylbenzene) networks

Carbon monoliths with well-defined macropores and high surface areas were prepared by carbonization of macroporous poly(divinylbenzene) (PDVB) monoliths. The carbonization reactions of PDVB networks are studied by thermal analysis and FT-IR measurements. According to the measurement results, the PDVB networks are mostly pyrolyzed at 430 °C and their structures dynamically change to graphite-like structure between 600 and 700 °C. The macropore structure retained while the mesopores disappeared after carbonization. In addition, the surface area of the obtained carbons dramatically increased over 900 °C. The typical carbon monolith carbonized at 1000 °C for 2 h had a surface area of 1500 m² g^?1 and uniform macropores with a diameter of 1 μm.     

Thermal stability of fatty acids in subcritical water

In this work, hydrolytic reaction conditions of various temperatures (300–370 °C) and times (0–30 min) at a constant pressure of 20 MPa were applied to the thermal decomposition of three kinds of fatty acids (FAs), stearic acid, oleic acid, and linoleic acid, in subcritical water. The degradation characteristics were investigated from the derived data, and the thermal stability of FAs in subcritical water was estimated. The primary reactions we observed were isomerization and pyrolysis of FAs. The main pathway of degradation was deduced by analyzing the contents of pyrolyzed products. We found that more saturated FAs have greater thermal stability in subcritical water. All FAs remained stable at 300 °C or below. Based on these results, we recommend that hydrolysis of vegetable oils and fats using subcritical water should be carried out below 300 °C (at 20 MPa) and for less than 30 min to obtain high-yield FA production.     

Thermal degradation and evolved gas analysis: A polymeric blend of urea formaldehyde (UF) and epoxy (DGEBA) resin

A polymeric blend has been prepared using urea formaldehyde (UF) and epoxy (DGEBA) resin in 1:1 mass ratio. The thermal degradation of UF/epoxy resin blend (UFE) was investigated by using thermogravimetric analyses (TGA), coupled with FTIR and MS. The results of TGA revealed that the pyrolysis process can be divided into three stages: drying process, fast thermal decomposition and cracking of the sample. There were no solid products except ash content for UFE during combustion at high temperature. The total mass loss during pyrolysis at 775 °C is found to be 97.32%, while 54.14% of the original mass was lost in the second stage between 225 °C and 400 °C. It is observed that the activation energy of the second stage degradation during combustion (6.23 × 10⁻⁴ J mol⁻¹) is more than that of pyrolysis (5.89 × 10⁻⁴ J mol⁻¹). The emissions of CO₂, CO, H₂O, HCN, HNCO, and NH₃ are identified during thermal degradation of UFE.     

The utilization of TG/GC/MS in the establishment of the mechanism of poly(styrene) degradation

General purpose poly(styrene) is a large volume commodity polymer used in a variety of applications. It is widely used in food packaging, particularly for baked goods. In this application, the presence of styrene monomer, which has a distinctive taste and aroma, cannot be tolerated. Processing of the polymer and forming of the food container at an unacceptably high temperature leads to the formation of styrene monomer and finished articles with unacceptable aroma characteristics. An examination of the thermal degradation of poly(styrene) has revealed the origin of monomer formation. The thermal decomposition of poly(styrene) has been widely studied. However, most studies have been carried out at high temperature (>300°C) where many processes are occurring simultaneously. Degradation at lower temperature, 280°C, occurs in two well-defined steps. The first is thermolysis of a head-to-head bond present in the mainchain as a consequence of polymerization termination by radical coupling. This generates macroradicals which smoothly depolymerize to expel styrene monomer. The nature of the degradation is readily apparent from kinetic analysis of the isothermal thermogravimetry (TG) data and the identity of the single volatile product may be readily established by gas chromatography/mass spectrometry (GC/MS) analysis of the effluent from the TG analysis.     

Thermal properties of some hydrogenated poly(α-methyl styrenes)

The Synthesis of poly(isopropenyl cyclohexane) via the hydrogenation of poly(α-methyl styrene) is described. Depending on the reaction time and catalyst system a homopolymer or a copolymer is obtained. Under the conditions of synthesis both materials are highly syndiotactic. For the pure hydrogenated homopolymer (>99.9%) the glass transition temperature was found to be 185.4°C, about 20°C above T_g of poly(α-ethyl styrene). Contrary to expectations, the glass transitions of the 92/8, 33/67 poly(isopropenyl cyclohexane-co-methyl styrene) and poly(α-methyl styrene) are almost identical, as are the decomposition temperature ranges. Thermal data indicate that the decomposition mechanism of the copolymers and hydrogenated homopolymer is random scission. The thermogravimetric curves also indicate that the copolymers are random. Thus, chain stiffness appears not to increase rapidly with hydrogenation of this highly syndiotactic polymer.     

Dual-response nanocarrier based on graft copolymers with hydrazone bond linkages for improved drug delivery

Core–shell micelles with biodegradability, thermo- and pH-response were successfully demonstrated by poly(2-oxepane-1,5-dione-co-ɛ-caprolactone) (P(OPD-co-CL)) grafted with hydrophilic segments of amine-terminated poly(N-isopropylacrylamide) (At-PNIPAM). To compare with the graft copolymer, P(OPD-co-CL) block PNIPAM polymer was also prepared. The micelles with core–shell structure were formed with both graft and block copolymers by self-assembly in aqueous solutions, of which PNIPAM shell is thermo-response. Furthermore, P(OPD-co-CL)-g-PNIPAM also showed pH-sensitivity, which was attributed to the acid-cleavable property of the hydrazone bond. The low critical micelle concentrations (CMCs) of graft polymers and block polymers were 6.7 mg/L and 14.3 mg/L, respectively, which indicated the formation of stable micelles. Both drug-free and drug-loaded micelles were in uniformly spherical shape observed by transmission electron microscopy (TEM). The sizes of the drug-free and drug-loaded micelles prepared from graft polymer were 123.5 nm and 146.5 nm, respectively, and the sizes of those prepared from block polymer were 197.5 nm and 211.5 nm, respectively. The lower critical solution temperature (LCST) for the graft polymer was 34.3 °C, while that for the block polymer was 28.1 °C, demonstrating a thermo-response. The graft polymeric micelles exhibited thermo-triggered decelerated release at pH 7.4, and pH-triggered accelerated release at 25 °C in vitro release test, indicating that the graft polymeric micelles could be a promising site-specific drug delivery system for enhancing the bioavailability of the drug in targeted pathological areas.     

Structure characteristics contributing to flame retardancy in diazo modified novolac resins

The physical characteristics of two modified novolac resins (carbonyl phenyl azo novolac resin; CPAN and 4-(4-hydroxyphenyl azo) benzyl ester novolac resin; HPDEN) bearing nitrogen and aromatic functional groups by diazo-coupling or esterification in the branch structure of phenol novolac resin were examined. Presence of the modifiers raised the phenolic decomposition temperature (5% weight loss) from 300 °C (pure Phenolic) to 330 °C and 380 °C, while the char residue increased from 45% to 56% and 68%, respectively. The kinetics for thermal degradation energies (E_a) also rose from 151 kJ/mol K to 254 kJ/mol K (CPAN) and 273 kJ/mol K (HPDEN). The retarded decomposition kinetics is attributed both to the increase of crosslink densities and high aromatic content in the derivative resins. On the other hand, the diazo-coupling or phenyl diazenyl ester produces non-combustible gases (N₂, CO₂ and CO) during formation of aromatic char which dilute the ambient oxygen gas. Both the production of gases and the retarded kinetics due to cross-linking are definitive for the improved flame resistance.