iPP／aPP共混物溶液浇铸薄膜的形态结构研究

用透射电子显微镜和Ｘ射线衍射等方法研究了等规立构聚丙烯和无规立构聚丙烯共混物溶液浇铸膜的形态结构，结果表明，ａＰＰ的加入对ｉＰＰ的形态结构有很大的影响。     

The use of optical microscopy to follow the degradation of isotactic polypropylene (iPP) subjected to natural and accelerated ageing

Microscopy and mechanical properties are commonly used to follow the changes in morphology and mechanical resistance, respectively, of materials before and after any type of treatment. In this work, we used light microscopy (LM), scanning electron microscopy (SEM) and measurement of the mechanical properties to assess the natural ageing of samples of isotactic polypropylene (iPP) in Campinas and after exposure to Weather-Ometer type accelerated ageing equipment. The results obtained for the mechanical properties and by light microscopy (LM) allowed us to identify the ageing time based on the amount of radiation, for a 50% loss of elongation at break. The results were similar for samples subjected to the two types of ageing processes. Although a simple technique, LM was considered efficient when compared with SEM and the measurement of mechanical properties.     

In situ FT-IR spectroscopic study on the conformational changes of isotactic polypropylene in the presence of supercritical CO2

The conformational changes of isotactic polypropylene (iPP) under supercritical CO₂ condition with different pressure and temperature have been carefully studied by in situ Fourier-transform infrared spectroscopy (FT-IR). Analysis of the corresponding spectra shows that the conformational ordering by supercritical CO₂ results in the intensity enhancement of the regularity bands of iPP. Due to the high CO₂ concentration and strong intermolecular interaction, iPP can reach an equilibrium state in a short time at high CO₂ pressure. The equilibrium time increases with soaking temperature. After supercritical CO₂ treatment, two mechanisms, the formation of short helix from amorphous phase and the extension of short helix into long one, happen simultaneously. The latter mechanism undergoes quickly at the beginning of induced conformational changes and then slows down, resulting in the slight increase of crystallinity. At the same time, the conformational ordering in amorphous phase happens continuously until a thermodynamic equilibrium. In summary, in the presence of supercritical CO₂, the conformational ordering of iPP chains occurs exclusively in the amorphous region, with no impact on the crystal part.     

The effect of annealing on the elastoplastic response of isotactic polypropylene

Four series of tensile loading-unloading tests are performed on isotactic polypropylene in the sub-yield domain of deformations at room temperature. In the first series, injection-molded specimens are used as produced, whereas in the other series the samples are annealed for 24 h at 120, 140 and 160 °C, which covers the low-temperature region and an initial part of the high-temperature region of annealing temperatures. A constitutive model is developed for the elastoplastic behavior of a semicrystalline polymer. The stress-strain relations are determined by five adjustable parameters that are found by fitting the experimental data. The effect of annealing is analyzed on the material constants.     

Heat treatment of isotactic polypropylene: the effect of free quenching from the melt state

Studying the effect of quenching from the melt state on the structure and impact resistance of Isotactic polypropylene (iPP) was the major aim of this work. Various tests were applied to confirm changes that occur to iPP, namely impact tests, WAXD, FTIR, and the density. The quenching from the melt state to different temperatures decreased the values of Izod impact strength for all the quenching temperatures. The FTIR result showed a decrease in the crystallinity of the polymer at the free quenching temperature of 20?°C. The X-ray diffraction study revealed that the α structure dominates the main morphology of iPP.     

Investigation on structural changes of isotactic polypropylene mesophase in the heating process by using two-dimensional infrared correlation spectroscopy

Two-dimensional FT-IR correlation spectroscopy was used to reveal the structural changes of isotactic polypropylene(iPP) mesophase during the heating process.The co-relationship among the regular helical bands of iPP was discussed according to synchronous spectrum.The results show that the segments with different length-helixes were found to undergo a disordered process in the temperature range of 25-60 ℃.     

原位傅里叶变换红外光谱跟踪等规聚丙烯在升温过程中的构象变化

自从 Natta[1]首次成功合成高分子量的等规聚丙烯 (i PP)以来 ,红外光谱就被广泛地应用于 i PP的组成和结构的表征[2～ 13] .1 988年 ,Hendra等[3] 采用逐步升温方法 ,静态观察 i PP红外光谱的构象规整谱带随温度的变化 ,发现当温度高于 1 35℃时 ,i PP分子链的活动性增加 ,样品的凝聚态结构发生了明显的变化 .然而 ,他们却未能找出产生这一现象的直接原因 .本文利用快速升温傅里叶变换红外光谱(FTIR)在线跟踪 i PP大分子在升温过程中的分子构象变化 ,并结合其它实验手段 ,阐明了上述现象来源于 i PP非晶区螺旋序列的无序化 .1　实…     

新拓扑指数A_m在有机物气相色谱法中光离子化灵敏度的分析中的应用

本文把Am拓扑指数与分子连接性指数首次用于有机化合物气相色谱分析的光离子化灵敏度的结构-性能相关性研究中，在与相应体系的光离子化灵敏度进行相关分析时发现，Am指数、分子连接性指数均能较好地反映化合物的结构特征，将二者组合，得到了更为满意的构效关系的数学模型。     

The influence of the memory effect on preparative separations using the amylose tris(3,5-dimethylphenylcarbamate) stationary phase

Acid/base mobile phase modifiers affect enantioseparations in ways that are not yet understood for the lack of systematic studies, which makes the scale-up of preparative separations difficult to predict. Shifts of the selectivity of certain pairs of enantiomers upon exposure of the column to these modifiers is amply documented. Furthermore, once the modifier has been removed from the mobile phase, the improved selectivity remains, this phenomenon has been named the memory effect. We selected four enantiomeric pairs for a systematic study of this memory effect. The selectivity of 4-chlorophenylalanine ethyl ester (4CPEE) improves after a solution of ethanesulfonic acid (ESA) is percolated through the column. The selectivity of propranolol HCl and Tröger's base increases after a solution of diiospropylethylamine is percolated through the column. The selectivity of these three pairs of enantiomers is inversely affected by percolation of the opposite acid/base solution. Each of these four compounds reached an equilibrium concentration that maintained the separation of the enantiomeric pairs. In contrast, the selectivity of trans-stilbene oxide (TSO) is not affected by either acid/base modifier. Preparative separations can be used to detect changes in the active surface of the chiral polymer stationary phase by measuring the change in selectivity and resolution when modifiers are used. Preparative method development was carried out on analytical columns and scale-up to 1 cm ID columns were performed in this study.     

The influence of crystal structures of nucleating agents on the crystallization behaviors of isotactic polypropylene

The crystals of N, N′-dicyclohexyl-2,6-naphthalenedicarboxamide (DC26NDCA) and N,N′-dicyclohexyl-1,4-naphthalenedicarboxamide (DC14NDCA) were selected as nucleating agents to induce the crystallization of isotactic polypropylene (i-PP). The influence of the crystal structures of the nucleating agents on the crystallization behaviors and morphologies was studied by means of differential scanning calorimeter, wide-angle X-ray diffraction, polarized light microscopy, and atomic force microscopy (AFM). The results show that DC26NDCA is a selective β-nucleating agent for the i-PP crystallization, while DC14NDCA only has a very weak α-nucleating effect for the i-PP crystallization. The dynamic growth processes reveal that i-PP crystals grow with different crystallization behaviors in the presence of the nucleating agents. The i-PP lamellar structures on the crystal surfaces of the nucleating agents were observed by AFM in details, which suggested that the nucleating agents induced the epitaxial growth of the i-PP lamellae.     

Epitaxial behavior of HDPE on the boundary of highly oriented iPP substrates

The epitaxial crystallization behavior of high-density polyethylene on the boundary of highly oriented isotactic polypropylene (iPP) substrates has been investigated by means of atomic force microscopy (AFM) and transmission electron microscopy (TEM). The results obtained from AFM and TEM indicate that the epitaxial nucleation of HDPE on the highly oriented iPP substrates occurs earlier than that in the pure HDPE phase, i.e., homogeneous nucleation. Therefore the epitaxially grown HDPE lamellae can grow across the boundary of the iPP substrate into the HDPE spherulitic phase with the epitaxial orientation relationship remaining.     

A comparison study on the homogeneity and heterogeneity fiber induced crystallization of isotactic polypropylene

The crystallization behavior of iPP in composites with PET, Nylon-6 and its own fibers under various conditions was studied using an optical microscope equipped with a hot stage. The results show that the nucleation capacity of PET and Nylon-6 fibers towards the iPP matrix is mainly controlled by the shear flow of the iPP matrix during sample preparation. When the composites were prepared at a temperature where the iPP was kept in its supercooled state, the nucleation of iPP on the PET and Nylon-6 fiber surfaces was enhanced due to the shearing of the iPP melts caused by introduction of the fibers. The nucleation was markedly reduced by keeping the composites at the fiber introduction temperature for a short time to relax the shear flow of the iPP matrix. The nucleation of iPP on its own fiber, however, is mainly related to the nature of the iPP fiber itself. No detectable morphological change of iPP on its own fiber can be identified under all thermal conditions used in this study.     

Influence of the order of polymer melt on the crystallization behavior: II. Crystallization kinetics of isotactic polypropylene

The crystallization behavior of isotactic polypropylene (iPP) melts with a high order has been carefully examined by differential scanning calorimetry (DSC) and polarized light microscopy (PLM). The experimental results show that the helically ordered iPP melt crystallizes by heterogeneous nucleation with two-dimensional diffusion controlled growth and the Avrami exponent is about 2. The data available both from our DSC and PLM experiments and from the literature indicate that the order of a polymer melt can speed up the crystallization process. When some unmelted materials exist in the ordered melt, the crystallization will become more rapid. Received: 16 June 2000 Accepted: 16 October 2000     

Effects of stereo-defect distribution on the crystalline morphology and tensile behavior of isotactic polypropylene prepared by compression molding process

In this study, the aggregation morphology, tensile behavior, and morphology evolution during the tensile test of two isotactic polypropylene (iPP) samples with similar molecular weight and average isotacticity but different uniformities of stereo-defect distribution are investigated by differential scanning calorimetry (DSC), two-dimensional wide angle X-ray diffraction (2D-WAXD), and scanning electronic microscopy (SEM). The results revealed that the uniformity of stereo-defect distribution of iPP determines the crystalline structure and aggregation morphology, and further influences the tensile behavior and morphology evolution during the tensile test. For PP-A with less uniform stereo-defect distribution, its ability of crystallization is stronger compared with PP-B, resulting in smaller spherulite sizes, higher melting point and degree of crystallinity, and narrower distribution of lamellar thickness of the compression molding specimens. During the tensile test, mainly the inter-spherulite deformation takes place at the early stage for deformation, which further results in drastic deformation of lamellar and high degree of reorientation at the strain increases, exhibiting higher yield strength and elastic modulus, and lower elongation at break compared with PP-B; for PP-B with more uniform stereo-defect distribution, larger spherulite sizes, lower melting point and degree of crystallinity in its compression molding sample are observed. During the tensile test, intra-spherulite deformation mainly takes place, which can disperse the tensile stress more uniformly. As the strain increases, lower degree of crystalline destruction and reorientation of the crystallites take place. The yield strength and elastic modulus of PP-B is lower than PP-A, and its elongation at break is higher.     

温度对iPP和TMB-5/iPP结晶行为的影响

通过DSC和同步辐射WAXS技术测定了结晶温度对iPP和TMB-5/iPP结晶行为的影响.结果表明,随等温结晶温度升高,iPP总结晶度变化不大,但是β晶型含量降低的同时α晶型含量增加.TMB-5是一种具有温度依赖的选择性成核剂,当等温结晶温度高于140℃时,含TMB-5成核剂的iPP的β晶型的含量急剧降低.本文进一步探讨了TMB-5对iPP结晶行为影响的机理.     

Influence of structure on the properties of polypropylene copolymers and terpolymers

Several Ziegler-Natta copolymers of iPP with ethylene or 1-butene, and terpolymers with both counits have been characterized, devoting special attention to the effect of composition and processing conditions on the crystal structure and final properties. DSC and X-ray diffraction were used to study the polymorphism of copolymers and terpolymers. Comonomer insertion interrupts the isotactic sequences, acting as a structural defect, and the formation of γ form is enhanced. Moreover, crystallinity decreases and crystal structure is modified. Comonomer type and concentration determine the extent of these modifications, resulting in important changes in macroscopic properties. In particular, the excellent optical properties of the analyzed terpolymers make them very attractive for applications such as transparent film or packaging.     

A test to determine the nature and presence of the memory effect columns packed with the amylose tris(3,5-dimethylphenylcarbamate) stationary phase

Acid/base mobile phase modifiers affect enantioseparations in ways that are not fully understood yet, for the lack of systematic studies. This makes chiral analysis of some pharmaceuticals difficult to reproduce. Once a column has been exposed to a modifier, the selectivity of certain pairs of enantiomers may change, for the better or the worse. We study the behavior of five enantiomeric pairs, three which are highly sensitive to the addition of certain modifiers and two that have little sensitivity to these modifiers. Their use permits the determination of the extent of the memory effect response on individual columns. The selectivity of 4-chlorophenylalanine methyl and ethyl ester, and of ketoprofen improve as a solution of ethanesulfonic acid is percolated through the column. As a result, these pairs are most useful for the determination of the extent of acid memory effect on a column. The selectivity of propranolol HCl and, to a lesser degree, Tröger's base increases as a solution of diisopropylethylamine is percolated through the column. The separation of each one of these five pairs is inversely affected by the percolation of the opposite acid/base solution. We used trans-stilbene oxide (TSO) as a ‘standard’ to determine the column stability because no memory effect is observed for it (its retention, enantioselectivity, and resolution remain constant). Understanding whether a column is under the influence of the memory effect is critical to both the analysis of pharmaceutical ingredients and to the development of preparative purification techniques for racemic mixtures. Thus, columns that were unreliable for method development and method transfer, due to the memory effect and a lack of proper solvent exposure records, can now be used.     

Conformational effect on fluorescence emission of tetraphenylethylene-based metallacycles

Herein,we designed and constructed two metallacycles,1 and 2,to illustrate the conformational effect of isomeric AIE fluorophores on the platform of supramolecu...     

Determination of trace levels of mercury in aqueous solutions by inductively coupled plasma atomic emission spectrometry: Elimination of the ‘memory effect’

The measurement of mercury in aqueous solutions by ICP-AES is adversely affected by the memory effect wherein mercury accumulates within the sample introduction system and is slowly released over time to give increasing response signals at the same initial mercury concentration. The memory effect is obviated by the addition of Hg(II) complexants: thiourea and gold(III) chloride are both effective in preventing mercury sorption and vapor buildup with the latter being preferred because the memory effect vanishes more rapidly. Conditions are described wherein it is possible to quantify low levels of mercury(II) in aqueous solutions by ICP-AES under routine operating conditions that can be applied to other metal ions by adding 1 mg of gold(III) chloride per 3 mg of mercury(II) to those solutions.     

Influence of additives on the structure and properties of polymers

Investigations into the transformation of hexagonal into monoclinic modification in isotactic polypropylene (iPP) were carried out. The hexagonal phase () was obtained by crystallization from a melt of iPP samples containing small molecular compounds (additives). A decline in the amount of-modification and changes of dimensions of ordering areas, perpendicular to the chain axes of iPP, was analysed at various temperatures and times of heating.The interdependence between the structure of additives and the amount of-phase occurring and also the stability of this modification during thermal treatment was observed.Obtained results indicated that only some additives play the role of moderating agents for the phase transition process.A preliminary report of this work has been presented at XIII Congress of the International Union of Crystallography (9–18 August 1984).