Electrochemical Determination of Ascorbic Acid at γ-MnO<Subscript>2</Subscript> Modified Carbon Black Microelectrodes

A carbon black microelectrode modified by -MnO₂ has been prepared. The electrocatalytical oxidation of ascorbic acid (AA) at this microelectrode was investigated. The 2nd-order linear scan voltammograms of AA are recorded from –0.5 to 0.5V (vs. SCE). The relationship between the oxidation peak current of AA and its concentration in the range of 1.0×10^–64.0×10^–3molL^–1 is linear. The detection limit (3) was found to be 6.0×10^–7molL^–1. Also, the determination of AA in samples is evaluated, and the results are satisfactory.     

Molecular structure of aniline in the gaseous phase: A concerted study by electron diffraction and ab initio molecular orbital calculations

The molecular structure of free aniline has been investigated by gas-phase electron diffraction and ab initio MO calculations at the HF and MP2 levels of theory, using the 6-31G^*(6D) basis set. Least-squares refinement of a model withC _s symmetry, with constraints from MP2 calculations, has led to an accurate determination of the C-C-C angle at theipso position of the benzene ring, =119.0±0.2 (where the uncertainty represents total error). This parameter provides information on the extent of the interaction between the nitrogen lone pair and the system of the benzene ring, and could not be determined accurately by microwave spectroscopy. The angles at theortho, meta, andpara positions of the ring are 120.3±0.1, 120.7±0.1, and 119.0±0.3, respectively. Important bond distances are r _g(C-C)=1.398±0.003 å andr _g(C-N) =1.407±0.003 å. The effective dihedral angle between the H-N-H plane and the ring plane, averaged over the large-amplitude inversion motion of the amino group, is ¦¦=44±4. The equilibrium dihedral angle is calculated to be 41.8 at the HF level and 43.6 at the MP2 level, in agreement with far-infrared spectroscopic information. The MO calculations predict that the differencer(C_ortho-C_meta) -r(C_ipso-C_ortho) is 0.008–0.009 å. They also indicate that the nitrogen atom is displaced from the ring plane, on the side opposite to the amino hydrogens. The displacement is 0.049 å at the HF level and 0.072 å at the MP2 level. The two calculations, however, yield very different patterns for the minute deviations from planarity of the ring carbons.     

Thermoanalytical study of linkage isomerism in coordination compounds: Part I. Reinvestigation of thermodynamic and thermokinetic of solid state interconversion of nitrito (ONO) and nitro (NO2) isomers of pentaaminecobalt(III) chloride by means of DSC

Solid state thermal isomerization of [Co(NH₃)₅(ONO)]Cl₂ (nitrito isomer) to [Co(NH₃)₅(NO₂)]Cl₂ (nitro isomer) and reverse reaction were investigated by non-isothermal differential scanning calorimetry (DSC) and found to be essentially an equilibrium process. The interconversions are accelerated at above 65 °C and reach to equilibrium state at about 155 °C. After establishment of the equilibrium the relative amounts of two isomers at any temperature are governed by Gibbs free energy relationship. The experimental enthalpy changes of isomerization of pure nitrito and nitro solid samples to the equilibrium state are −4.67 (±0.19) and 0.99 (±0.05) kJ mol⁻¹, respectively. From these values, total enthalpy change was calculated as: ΔH°=−5.66(±0.20) kJ mol⁻¹. Using Gibbs free energy relationship, equilibrium constant, total free energy and entropy changes were estimated at 60 °C as: K=7.72(±0.8),  kJ mol⁻¹ and  J K⁻¹ mol⁻¹.An initial rate method has been developed to determine the kinetic parameters of these reactions from non-isothermal DSC data. Both nitro to nitrito and reverse reactions obey first order kinetic law in solid state. Estimated activation parameters of forward and reverse paths at 60 °C are , , and , respectively. The negative activation entropy of both directions support the intramolecular mechanism of isomerization, including formation of a seven coordinate transition state, which formerly suggested based on spectral and X-ray methods.     

188Os Low Excited Levels

The -ray spectra of ¹⁸⁸Re decay have been studied by using a compton-suppressed spectrometer and a three parameters --T list coincidence system. Six -rays at 557, 810, 1463, 1867, 1936 and 2022 keV and three levels at 1443, 1936 and 2022 keV are confirmed again. Eight new -rays at 309.60±0.04, 826.90±0.02, 979.29±0.08, 1086.13±0.03, 1103.7±0.4, 1828.2±0.1, 1842.5±0.2, 1982.5±0.2 keV have been identified, three new levels at 309.60, 1828.2 and 1982.5 keV are assigned. The ^–-decay branching ratio is deduced.     

Electroreduction of anions on chemically etched and electrochemically polished Bi(1 1 1) electrode

Electroreduction kinetics of to anions at chemically etched (CHE) and electrochemically polished (EP) Bi(1 1 1) electrodes has been studied using rotating disc electrode method. The surface nanostructure of CHE Bi(1 1 1) and EP Bi(1 1 1) electrodes has been studied by in situ STM and the very different values of root mean squared roughness (Rms) have been obtained (1000 times higher for CHE Bi(1 1 1) (Rms  143 nm) than for EP Bi(1 1 1) (Rms  0.145 nm)). The influence of the nanoroughness of CHE Bi(1 1 1) on the current density, heterogeneous reaction rate constant and corrected Tafel plots (cTp) has been demonstrated. For CHE Bi(1 1 1) the more pronounced inhibition of electroreduction reaction at moderate negative surface charge density has been observed in comparison with EP Bi(1 1 1), caused by the differences in surface charge density and also in diffuse layer ψ₀ potential drop values at crystallographically different homogeneous regions (planes) exposed at the surface of the macroheterogeneous polycrystalline CHE Bi(1 1 1) surface. The very low apparent transfer coefficient α_app obtained indicates the nearly activationless charge transfer mechanism for electroreduction at the CHE Bi(1 1 1) electrode similarly to EP Bi(1 1 1). However, α_app only very weakly depends on Rms for the Bi electrodes at high negative surface charge densities where the values of ψ₀ potential are nearly equal for different planes at fixed electrode potential. At very high negative surface charge densities the cationic catalysis through the adsorbed ion pairs is possible.     

Determination of Nucleic Acids Based on Shifting the Association Equilibrium between a Heptamethine Cyanine Dye and Poly-Lysine

A near-infrared (near-IR) fluorescence recovery method for the determination of nucleic acids is presented. This method employs a two-reagent system composed of anionic heptamethines cyanine (HMC) and polycationic poly-lysine. The fluorescence of HMC, with maximum excitation and emission wavelengths at 778 and 804nm, respectively, was quenched by poly-lysine in proper concentration, but recovered by adding nucleic acids. Under optimal conditions, the recovered fluorescence was proportional to the concentration of nucleic acids. The calibration graphs are linear over the range of 5–300ngmL^–1 for herring sperm DNA (FS DNA), 2–100ngmL^–1 for calf thymus DNA (CT DNA) and 5–500ngmL^–1 for snake ovum RNA (SO RNA). The corresponding detection limits are 1.49ngmL^–1 for FS DNA, 0.7ngmL^–1 for CT DNA and 1.61ngmL^–1 for SO RNA, respectively. Four synthetic and three real nucleic acid samples were determined with satisfactory results.     

Formation of Aromatic and Other Unsaturated End Groups in Carboxymethyl Cellulose During Hot Alkaline Treatment

Carboxymethyl cellulose (CMC, DS 0.58) was treated in solutions of sodium hydroxide (0.001–1 M) at 95 °C. The treated (1–12 h) CMC samples were purified by dialysis and analyzed by UV spectroscopy and by UV resonance Raman spectroscopy (UVRRS) with excitation at 244 nm. A UV absorption maximum at 265 nm and a UVRR signal at 1650 cm⁻¹ were indicative of formation of -conjugated aldehyde end groups in CMC through -elimination. Another strong UVRR band at 1610 cm⁻¹ gave evidence on conversion of some of the -conjugated aldehyde end groups to alkali stable aromatic structures.     

Adsorptive Catalytic Voltammetry of Physcion in the Presence of Dissolved Oxygen at a Carbon Paste Electrode

A novel electroanalytical method for the determination of physcion is described for the first time. Physcion yields an adsorption catalytic voltammetric peak at –0.74V (vs. SCE) in 0.4molL^–1 NH₄Cl–NH₃·H₂O buffer solution (pH 10.5) at a carbon paste electrode (CPE). The experimental results indicated that physcion is efficiently accumulated at a CPE by adsorption. In the subsequent potential scan, physcion was reduced to a homologous anthrahydroquinone compound. The compound was then immediately oxidized to physcion by the dissolved oxygen in the solution, and then physcion was again reduced at the CPE. As a result, a cyclic catalytic reaction was established. The second-order derivative peak current is proportional to the physcion concentration in the ranges of 2.0×10^–104.0×10^–9molL^–1 (accumulation 90s) and 4.0×10^–92.0×10^–8molL^–1 (accumulation 60s). The limit of detection is 8×10^–11molL^–1 (S/N=3) for a 120s accumulation time. The method was applied to the direct determination of physcion in the medicinal plant polygonum multiflorum Thumb with satisfactory results.     

Dielectric properties of Ca(Zr0.05Ti0.95)O3 thin films prepared by chemical solution deposition

Ca(Zr_0.05Ti_0.95)O₃ (CZT) thin films were grown on Pt(1 1 1)/Ti/SiO₂/Si(1 0 0) substrates by the soft chemical method. The films were deposited from spin-coating technique and annealed at 928 K for 4 h under oxygen atmosphere. CZT films present orthorhombic structure with a crack free and granular microstructure. Atomic force microscopy and field-emission scanning electron microscopy showed that CZT present grains with about 47 nm and thickness about 450 nm. Dielectric constant and dielectric loss of the films was approximately 210 at 100 kHz and 0.032 at 1 MHz. The Au/CZT/Pt capacitor shows a hysteresis loop with remnant polarization of , and coercive field of 18 kV/cm, at an applied voltage of 6 V. The leakage current density was about at 3 V. Dielectric constant-voltage curve is located at zero bias field suggesting the absence of internal electric fields.     

Polarization and ESR studies of thermally pretreated γ-irradiated TiO2

Pellets of TiO₂ thermally pretreated at 450 and 540°C and -irradiated were polarized by d. c. field. The depolarization curves were resolved into different first order components having two and three depolarization constants. By heating the polarized pellets the Current Glow Peak curves were recorded where there were only two peaks around 65 and 400°C in case of pellets heated at 450°C and heated at 540°C and irradiated; and one more additional peak around 20°C in case of pellets heated at 540°C and heated at 450°C and irradiated thereon. In addition to those signals of O ₂ ^– and Ti³⁺ reported earlier there were distinctly four more, signals at g 1.933 and g 2.03, 2.036 and 2.043 appeared in case of samples heated at 540°C and heated at 450°C and irradiated thereon. The signal at g1.933 is attributed to Ti³⁺ ions in new phase Ti₄O₇ developed in heating at 540°C or due to irradiation and the rest of the signals are due to O _2ad ^– or O _ad ^– over the new phase near anion vacancy created.     

Reactions of 1-vinyl-4,5,6,7-tetrahydroindole and its mixtures with 4,5,6,7-tetrahydroindole in the presence of Cr- and Pd-coated catalysts

In the presence of Cr- and Pd-coated -alumina catalysts, 1-vinyl-4,5,6,7-tetrahydroindole (VTHI) and its mixtures with 4,5,6,7-tetrahydroindole (THI) are converted into 1-ethyl-4,5,6,7-tetrahydroindole (1-ETHI), indole, and 2-ethylindole, in proportions dependent on the reaction conditions and the catalyst. Over a sulfided 1% Pd--alumina catalyst in the presence of hydrogen at 200°C, VTHI is converted into 1-ETHI and THI. When the temperature is raised to 300–350°C, indole is formed in addition to these products. A 11 mixture of VTHI and THI over 1% Pd--alumina at 300°C gives indole and 2-ethylindole, over a sulfided 1% Pd --alumina catalyst at 200°C, 1-ETHI, and over a Cr oxide catalyst at 500°C, indole.Translated from Izvestiya Akademii Nauk SSSR, Seriya Khimicheskaya, No. 6, pp. 1417–1422, June, 1991.     

Studies on styrene phosphonic acid

Some properties of styrene phosphonic acid (SPA) were studied. The crystals were triclinic, witha=0.6434 nm,b=0.5842 nm,c=2.0338 nm, =96.17°, =97.33°, =79.65° andZ=4. SPA underwent a change in crystal structure at 78.8°C, the hydrocarbon network became disordered (liquid-like) at 138.5°C. Crystals melted at 148.6°C giving a cubic mesophase, then changed to an isotropic liquid at 155.6°C and at 162.13°C SPA underwent decomposition. Values for pK₁=2.15 and pK₂=7.66 were obtained at 25°C. The water solubility of SPA at several temperatures, and its interaction with surfactant micelles were determined.     

Extractive spectrophotometric determination of dioxouranium(VI) with the sodium salt of hexamethyleneiminecarbodithioate

The optimum conditions for the extractive spectrophotometric determination of dioxouranium(VI) with hexamethyleneiminecarbodithioate(HMICdt) have been established. Dioxouranium(VI) reacts with this ligand at pH 4.5 to form a yellowish-orange uncharged 12 metal-ligand complex which can be extracted by chloroform. The calibration graph was linear in the range of 1–20 g ml^–1 of dioxouranium(VI) at 335 nm. The molar absorptivity of the extracted species is 5.952×10³ l mol^–1 cm^–1 with Sandell's sensitivity of 0.04 g cm^–2. The average of 10 determinations of dioxouranium was 49.75 g for the samples containing 50 g of U(VI) and the variation from the mean at 95% confidence limit was 49.75±0.5955.     

Skeletal reactions of perfluoromethylethyl- and perfluorodiethylbenzocyclobutenes with 1,1- and 1,2-alkyl groups in SbF5

Taking perfluoro-1,1-dialkylbenzocyclobutenes as examples, it has been shown to be possible to enlarge the four-membered ring in polyfluorobenzocyclobutenes to five-membered in the presence of SbF₅, by cleavage of the four-membered ring followed by cyclization of the resulting polyfluorostyrene to the polyfluoroindane, which then undergoes further reactions. Perfluoro-1-methyl-1-ethylbenzocyclobutene isomerizes at 50°C in the presence of SbF₅ to perfluoro-,-o -trimethylstyrene, which is reversibly converted at 130°C into perfluoro-1,2-dimethylindane. Perfluoro-l,l-diethylbenzocyclobutene isomerizes at 130°C in the presence of SbF₅ to give perfluoro- -ethyl-,o -dimethylstyrene, which at 170°C gives perfluoro-2-methyl-3-ethylindene- and perfluoro-2-methyl-3-ethyl-4,5,6,7-tetrahydroindene. The last two compounds, together with perfluoro-o-dipropylbenzene, are obtained from per fluoro-1,2-diethylbenzocyclobutene-with SbF₅ at 170°C. From perfluoro-1-methyl-2-ethylbenzocyclobutene with SbF₅ at 95°C there is obtained perfluoro-1-ethylindane, while at 130°C, in addition to the latter compound, there are obtained perfluorinated 1,1-dimethylindane, 1,2-dimethylindane, ,,o-trimethylstyrene, 2,3-dimethylindene, and 2,3-dimethyl-4,5,6,7-tetrahydroindene.Translated from Izvestiya Akademii Nauk SSSR, Seriya Khimicheskaya, No. 5, pp. 1114–1120, May, 1990.     

Kinetics of the thermal and photochemical decomposition of aquapentacyanoferrate(III) in aqueous solution

Summary The kinetics of the thermal and photochemical decomposition of aquapentacyanoferrate(III) ion in aqueous solution in the presence ofo-phenanthroline was studied spectrophotometrically. The first-order rate constant (k ) at 30° C [I=1 M(NaCl)] for the thermal reaction is (1.49±0.13)×10^–6 s^–1 with H =(158±7)kJ mol^–1 and S=(42±4) JK^–1 mol^–1. The initial quantum yield for the photochemical reaction at pH=7 is independent of the light intensity and is (1.49±0.33)×10^–2 mol einstein^–1.A communication on this subject was presented at the XVI Latinamerican Chemistry Congress held at Rio de Janeiro. Brasil, October 14–20, 1984.     

Anomalous chemical shifts of benzene on spherical carbon adsorbents

Benzene adsorbed on spherical carbon adsorbents (SCA) heat-treated at 1273 K and above displayed in PMR spectra two signals with anomalous chemical shifts:=0 and=–10 ppm. The spectral characteristics of benzene adsorbed from the vapor phase at pressures p/p_s of 0.95, 0.666, and 0.106 and temperature 293 K were compared with those of benzene acquired on freezing of the liquid phase. The signal at =–10 ppm was found to be due to benzene molecules in micropores, while the signal at =0 was due to surface-bound benzene in larger-diameter pores.Translated from Teoreticheskaya i Éksperimental'naya Khimiya, Vol. 28, No. 1, pp. 77–79, January–February, 1992.     

Phase polymorphism of [Zn(DMSO)6](ClO4)2 studied by differential scanning calorimetry

Four solid phases of [Zn(DMSO)₆](ClO₄)₂ have been detected by differential scanning calorimetry (DSC). Specifically, the phase transitions were detected between: metastable phase KII ↔ supercooled phase K0 at , stable phase KIb ↔ stable phase KIa at , stable phase KIa ↔ stable phase K0 at . At T_m2 = 389 K crystals partially and at T_m1 = 465 K completely melts. From the entropy change values it was concluded that the phases: K0 and K0′ are the orientationally dynamically disordered phases, so called ODDIC crystals, and phases KIa, KIb and metastable KII are dynamically ordered but with some degree of positional disorder.     

Substituted lactones and their reactions

Hydrogenation of -methyl--alkyl--valerolactones with copper-chromium catalyst at 230°–250° gives 2-methyl-3-alkyltetrahydropyrans. Reduction of these lactones at 140°-170° gives 3 alkylhexane-2, 6-diols.For Part VI see [1].     

Catalytic hydrogenolysis of alkylfurans

The vapor-phase conversion of -methylfuran and -methyltetrahydrofuran on a sodium and potassium-activated palladium catalyst in a stream of hydrogen at atmospheric pressure at 200–450°C was investigated. Hydrogenolysis of -methylfuran and isomerization of -methyltetrahydrofuran to give 2-pentanone in both cases occur at 300° with identical selectivities. It is assumed that aliphatic ketones are formed from the alkylfurans on this catalyst via a parallel-consecutive scheme through direct hydrogenolysis of the alkylfurans and isomerization of their tetrahydro derivatives, which are formed as intermediates.Deceased.Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 1, pp. 43–45, January, 1976.