Electrochemical Properties of Electrode Materials Based on Pr5Mo3O16 + δ

Russian Journal of Electrochemistry - The electrochemical activity of electrode materials based on Pr5Mo3O16 + δ (РМО), and applied on the surface of Ce0.9Gd0.1O1.95 (GDC)...     

A Solid Fe2O3 Based Carbon–Epoxy Electrode for Potentiometric Measurements of pH

A solid Fe₂O₃ based carbon-epoxy composite electrode was investigated for use as a potentiometric pH sensor. The electrode was constructed using a mixture of sulfated iron(III) oxide, carbon power, and epoxy resin, which was deposited directly onto a glass tube. The effect of composition (Fe₂O₃, carbon and epoxy resin) on the electrode response and its calibration curve (mV/pH) were investigated. The analytical behavior of the electrode in acid–base titrations was compared with that of a glass electrode. A linear response from pH 1.7 to 12.2 with a slope of –39.7 ± 0.6 mV/pH (at 25°C) was observed.     

Structure and Electric Conductivity of (La,Sr)(Ga,Mg)O3-α Solid Electrolyte

Electric conductivity, Raman spectra, and thermal expansion of La_0.88Sr_0.12Ga_0.82Mg_0.18O_2.85 solid solution (LSGM1218) based on lanthanum gallate were studied at various temperatures, and Xray phase analysis was performed at room temperature. Dilatometric measurements showed that secondorder phase transitions occur at 775±10$ and 880± 20 K. The transition around 880 K is confirmed by Raman spectra and by a change in the conductivity activation energy in this temperature range. This transition is associated with a symmetry change in the oxygen sublattice.     

Preparation and Electrochemical Performance of Cobalt-free Cathode Material Ba0.5Sr0.5Fe0.9Nb0.1O3-δ for Intermediate-temperature Solid Oxide Fuel Cells

Perovskite oxide Ba0.5Sr0.5Fe0.9Nb0.1O3-δ（BSFN） as a cobalt-free cathode for intermediate-temperature solid oxide fuel cells（IT-SOFCs） on the Ce0.5Sm0.2O1.9（SDC） and La0.9Sr0.1Ga0.8Mg0.23O3-δ（LSGM） electrolytes was prepared and investigated. The single phase BSFN oxide with a cubic perovskite structure and relatively high elec- trical conductivities was obtained after sintering at 1250℃ for 10 h in air. The BSFN cathode exhibited excellent chemical stability on the SDC and LSGM electrolytes at temperatures below 950 ℃. The area specific resistance of the BSFN cathode on the SDC and LSGM electrolytes were 0.024 and 0.021 Ω·cm2 at 800℃, respectively. The maximum power densities of the single cell with BSFN cathode in 300 μm-thick SDC and LSGM electrolytes achieved 414 and 516 mW/cm2 at 800℃, respectively. These results show that the BSFN material is a promising co- bait-free cathode candidate to be used in IT-SOFCs. A combination of the BSFN cathode and LSGM electrolyte is preferred owing to its excellent electrochemical performance.     

Microstructure analysis of (Ba,Ca)(Fe,Mg)O3-δ for rapid CO2 absorption by Mössbauer spectroscopy

The CO₂ absorption properties and the microstructure of (Ba,Ca)(Fe,Mg)O_{3 -} have been studied by TGA, XRD, and Mössbauer spectrometry. Paramagnetic doublets of Fe^IV and Fe^III appeared in the Mössbauer spectra of cubic (Ba_0.5Ca_0.5)(Fe_0.5Mg_0.5)O_{3 -} heated in CO₂ up to 600 °C, and a pair of sextets of tetrahedral Fe^III (H_in = 43 T) and octahedral Fe^III (H_in = 51 T) were produced above 800 °C, and an additional sextet characteristic of Fe^III in a spinel structure (H_in = 48 T) was observed at 1000 °C. On the other hand, a pair of sextets of tetrahedral and octahedral Fe^III of the orthorhombic (Ca_0.95Ba_0.05)(Fe_0.5Mg_0.5)O_{3 -} showed hardly any change after absorption of CO₂. It is concluded that only a small portion of Mg entered the orthorhombic phase of (Ca_0.95Ba_0.05)(Fe,Mg)O_{3 -} and Mg preferred the octahedral B site of the perovskite lattice. The excess Mg formed separate CaO-MgO mixed oxide, and the primary mechanism of CO₂-trapping is the formation of CaMg(CO₃)₂.     

(Ba,Ca)(Co,Fe)O3-δ系列混合导电型透氧膜的研究

采用改进的Ｐｅｃｈｉｎｉ法合成了（Ｂａ,Ｃａ）（Ｃｏ,Ｆｅ）Ｏ３－δ系列材料,对其结构,透氧量及透氧稳定性进行了考察,结果表明,材料具有较高的透氧量和透氧稳定性,其中Ｂａ０．９５Ｃａ０．０５Ｄｏ０．８Ｆｅ０．２Ｏ３－δ在９５０℃透氧量高达１．４ｍｌ／（ｃｍ＾２．ｍｉｎ）,８５０℃稳定操作１６０ｈ以上,将其应用于膜反应器,对无催化剂的甲烷氧化偶联反应作了尝试,结果表明,对甲烷氧化偶联反应具有较高的选择,但甲烷转化率较低。     

Redox Behavior and Transport Properties of Composites Based on (Fe,Ni)<Subscript>3</Subscript>O<Subscript>4 ± δ</Subscript> for Anodes of Solid Oxide Fuel Cells

The Fe–Ni–O system designed for producing bimetal-containing composite anodes of solid oxide fuel cells (SOFCs) was studied. The solubility of nickel in the structure of spinel (Fe,Ni)₃O_{4 ± δ} at atmospheric oxygen pressure is ~1/3. Moderate reduction at 1023 K and p(O₂) ≈ 10^–20 atm leads to partial decomposition of spinels, forming an electron-conducting phase (Fe,Ni)_1–yO and submicron bimetallic Fe–Ni particles on the oxide surface, which have potentially high catalytic activity. The electron conductivity has a thermally activated character and increases substantially during the reduction. In the anode conditions of SOFCs, the electric conductivity reaches 30–100 S/cm, while the thermal expansion coefficients are ~12 × 10^–6 K^–1, which ensures compatibility with solid electrolytes. At the same time, significant volume changes during the redox cycling (up to ~1% on the linear scale) necessitate the introduction of additional components such as yttria-stabilized zirconia (YSZ). The polarization resistance of the model composite anode of reduced Fe₂NiO_{4 ± δ} and YSZ deposited on the YSZ solid electrolyte membrane was ~1.8 Ohm cm² at 923 K in a 4% H_2–Ar–H₂O atmosphere.     

Electrochemical Sensor Based on Magnetic Fe3O4–Reduced Graphene Oxide Hybrid for Sensitive Detection of Binaphthol

Russian Journal of Electrochemistry - Naphthol is an environmental pollutant with highly toxic and corrosive. Naphthol can be absorbed by the body easily through the skin, and can cause serious...     

The microenvironment of iron in (Ba,Ca)(Fe,Co)O3−δ catalyst system: A Mössbauer study

Undisturbed, non-fertilized woodland soil (“loamy sandy soil” type) from 1 m below surface was dry and wet sieved. Sieving fractions of <10–1000 μm were analyzed for total alpha-activity. Thorium and uranium contents were determined by alpha-spectrometry after radiochemical separation. Soluble and insoluble parts of thorium and uranium were determined in the sieved fractions indicating that the isotope distribution in soil correlates with the particle size distribution: The smaller the size fraction the higher the isotope content. Isotope ratios of²²⁸Th/²³²Th, and²³⁴U/²³⁸U are discussed.     

MO-RE2O3-B2O3(M=Mg,Ca,Sr,Ba;RE=La,Eu,Gd)玻璃的发光性质

在空气中采用高温固相反应方法合成的17MO－（8-x-y)-75B2O3-xGd2O3(MLBEG,M-Mg,Ca,Sr,Ba)玻璃，在紫外光（λex=350nm)激发下发射蓝光和红光，在绿色光（λex=532nm)激发下发射红光，电子自旋共振谱研究表明玻璃体系中有Eu^2 离子存在，蓝色区的宽带发射是Eu^2 离子的5d-4f跃迁发射：红色区的窄带发射是Eu^3 离子的5Do-7FJ(J=1,2,3,4)跃迁发射，发现玻璃中的碱土金属离子对Eu^3 /Eu^2 离子的比例有很大影响，选择不同的碱土金属离子可以调节玻璃蓝色光和红色光的相对发射强度，MLBEG玻璃的发光性质可用于转换太阳能，增强植物的光合作用。     

Optimization on fabrication and performance of A-site-deficient La0.58Sr0.4Co0.2Fe0.8O3-δ cathode for SOFC

A-site-deficient perovskite cathode material La_0.58Sr_0.4Co_0.2Fe_0.8O_3 − δ (L58SCF) is coated on the yttria-stabilized zirconia electrolyte by screen-printing technique. Several key fabrication parameters including selection of additives (binder and pore former), effect of coating thickness, sintering temperature and time on the microstructure, and electrochemical performance of cathode are investigated by scanning electron microscopy and electrochemical impedance spectroscopy. We study the microstructure and the electrochemical property of the cathode with different kinds of additives. Results show that the cathode possesses fine microstructure, enough porosity, and ideal electrochemical property when polyvinyl butyral serves as both binder and pore former in the cathode. The cathode with three screen-printing coats (thickness 28 ± 7 μm, weight 6.07 ± 0.72 mg cm⁻²) sintering at 1,000 °C for 2 h shows lower polarization resistance of 0.183 Ω cm² at 800 °C. Based on the optimized parameters, the polarization resistances of the L58SCF–Ce_0.8Gd_0.2O_{1.9 – δ} composite cathode display the R _p values of 0.067 Ω cm² at 800 °C, 0.106 Ω cm² at 750 °C, 0.225 Ω cm² at 700 °C, and 0.550 Ω cm² at 650 °C.     

Studying the O2, Metal/O2– (Solid Electrolyte) Electrode System on Model Electrodes: The Electrolyte Surface Layer Properties

A model cell that features a set of parallel platinum contacts adjacent to one another is studied by an impedance spectroscopy method. The characteristic linear size (width) of a contact is nearly 100 m. Even contacts are used as a working electrode and odd, as an internal reference electrode. The difference between electrode spectra, when measured relative to the latter and to a traditional reference electrode deployed at a distance, suggests that an expansion of the triple-phase boundary does exist and exceeds 0.3 mm and that electric properties of the electrolyte's surface layer differ from those of the bulk.     

Low frequency vibrational spectra of crystalline and glassy metaborates Ba2MII(B3O6)2 (MII  Mg,Ca, Ni,Co, Cd)

The low frequency vibrational spectra (Raman and IR) of crystalline metaborates Ba₂M^II(B₃O₆)₂ (M^II  Mg, Ca, Ni, Co, Cd) are interpreted on the basis of a factor group analysis and with the help of ²⁴Mg²⁶Mg and ⁴⁰Ca⁴⁴Ca isotopic shifts. The far-IR spectra of the glasses appear as the envelope of the spectra of the corresponding crystalline compounds for M^II  Mg, Ca and Cd, but they exhibit an additional broad absorption centred near 400 cm⁻¹ for M^II  Co, Ni and Zn. This absorption is assigned to a fourfold coordination of part of the M^II cations, the remaining being in sixfold coordination (as in the crystal) and responsible for a broad absorption in the 300-200 cm⁻¹ region. The possible existence of correlations between coordination and vibrational frequencies is discussed for either alkali and alkaline-earth cations, or transition elements.     

A High Performance Sensor for L-ascorbic Acid Based on Electrode Modified With Chromium(Ⅲ)-Tetra(4-N,N,N-Trimethylanilinium)-Porphyrin

L-ascorbic acid (AA) or Vitamin C is one of the most important water-soluble antioxidants and cellar redox-regulator. It is required widely in biological metabolism and is one of the most frequently taken vitamins to supplement inadequate dietary intake. Therefore, there has been wide demand in food and pharmaceutical industries and in nutritional assessment for the development of selective, simple, accurate and rapid technique to determine AA.     

Molecular Magnetic Materials Based on {CoIII(Tp*)(CN)3}− Cyanidometallate: Combined Magnetic,Structural and 59Co NMR Study

The cyanidocobaltate of formula fac-PPh₄[Co^III(^Me2Tp)(CN)₃] ⋅ CH₃CN ( 1 ) has been used as a metalloligand to prepare polynuclear magnetic complexes (^Me2Tp=hydrotris(3,5-dimethylpyrazol-1-yl)borate). The association of 1 with in situ prepared [Fe^II(bik)₂(MeCN)₂](OTf)₂ (bik=bis(1-methylimidazol-2-yl)ketone) leads to a molecular square of formula {[Co^III{(^Me2Tp)}(CN)₃]₂[Fe^II(bik)₂]₂}(OTf)₂ ⋅ 4MeCN ⋅ 2H₂O ( 2 ), whereas the self-assembly of 1 with preformed cluster [Co^II₂(OH₂)(piv)₄(Hpiv)₄] in MeCN leads to the two-dimensional network of formula {[Co^II₂(piv)₃]₂[Co^III(^Me2Tp)(CN)₃]₂ ⋅ 2CH₃CN}_∞ ( 3 ). These compounds were structurally characterized via single crystal X-ray analysis and their spectroscopic (FTIR, UV-Vis and ⁵⁹Co NMR) properties and magnetic behaviours were also investigated. Bulk magnetic susceptibility measurements reveal that 1 is diamagnetic and 3 is paramagnetic throughout the explored temperature range, whereas 2 exhibits sharp spin transition centered at ca. 292 K. Compound 2 also exhibits photomagnetic effects at low temperature, selective light irradiations allowing to promote reversibly and repeatedly low-spin⇔high-spin conversion. Besides, the diamagnetic nature of the Co(III) building block allows us studying these compounds by means of ⁵⁹Co NMR spectroscopy. Herein, a ⁵⁹Co chemical shift has been used as a magnetic probe to corroborate experimental magnetic data obtained from bulk magnetic susceptibility measurements. An influence of the magnetic state of the neighbouring atoms is observed on the ⁵⁹Co NMR signals. Moreover, for the very first time, ⁵⁹Co NMR technique has been successfully introduced to investigate molecular materials with distinct magnetic properties.     

Heat of Formation for LiMyMn2−yO4 (M=Co,Cr, Li,Mg, Ni) Spinel Solid Solution

The enthalpy of formation for LiM_yMn_2–yO₄ (M=Co, Cr, Li, Mg, Ni) was measured by a Tian-Calvet type high temperature isothermal microcalorimeter. The standard enthalpy of formation for LiMn₂O₄ at 876 K was evaluated to be H_f⁰=–1404.2±6.4 kJ mol^–1. The partial substitution of Co and Ni for Mn decreased the absolute H_f⁰ value, while that of Cr and Mg for Mn increased the absolute H_f⁰ value. In the case of the partial substitution of Li for Mn, no marked change in H_f⁰ could be observed.This revised version was published online in November 2005 with corrections to the Cover Date.     

Protonic and Oxygen Conduction of Perovskites ATi0.95M0.05O3 - α (A = Ca,Sr, Ba; M = Mg,Sc) in Humid Air

Measurements of the total conduction (450-1030°C) and transport numbers for ions and protons (450-850°C) of titanates ATi_0.95M_0.05O_{3 -} (A = Ca, Sr, Ba; M = Mg, Sc) in humid air are performed. Partial conductions (ionic, protonic, oxygen, hole) and their effective energies of activation are determined. The results are discussed within a model of separate transport of proton and oxygen ion.     

57Fe Mössbauer spectroscopy predicts superstructure for K0.08[Cu(II)(N,N'app)Cl]2[Fe(III)(CN)6].0.92H3O.3H2O

The compound [Cu(N,N'app)Cl](2)[Fe(CN)(6)].xH(2)O, with N,N'app being bis(N,N'-3-aminopropylpiperazine), was prepared and its structure determined by single crystal X-ray analysis, confirming a ratio of two copper complexes to one iron complex; (57)Fe M?ssbauer spectra showed three quadrupole doublets typical of iron(iii) low spin species which call for the presence of a superstructure.     

Electroconductivity of Solid Solutions Cs3–2x M x PO4 (M = Ba, Sr, Ca, Mg)

Solid solutions Cs_{3 – 2x} M _x PO₄ (M = Ba, Sr, Ca, Mg) are synthesized and their thermal behavior and electroconductivity are examined. Adding elements of Subgroup IIA of the periodic table into cesium orthophosphate shifts the phase transition, which occurs in pure Cs₃PO₄ at 450–620°, towards lower temperatures and raises the cesium cation conductivity at low temperatures. The electroconductivity of a high-temperature modification of Cs₃PO₄ is weakly dependent on the presence and concentration of such additives, which points to structural disordering of the cesium sublattice.     

Syntheses and Crystal Structures of (H3O)(C3H5N2)[Mn(OH)6 Mo6O18]·3.5H2O and (H3O)3[Co(OH)6Mo6O18]·7H2O

The crystals of the title compounds (H3O)(C3H5N2)[Mn(OH)6Mo6O18]·3.5H2O 1 and (H3O)3[Co(OH)6Mo6O18]·7H2O 2 have been prepared and structurally determined by X-ray single-crystal diffraction. Compound 1 crystallizes in monoclinic, space group C2/c with a = 21.5018(9), b = 10.9331(5), c = 11.8667(5)A,β = 95.3570(10)o, V = 2777.5(2)A3, Z = 4, Dc = 2.802 g/cm3, Mr = 1171.80,μ(MoKα) = 3.173 mm-1, F(000) = 223, the final R = 0.0458 and wR = 0.1041 for 2093 observed reflections (I>2σ(I)); Compound 2 crystallizes in monoclinic, space group P21/c with a = 11.4042(12), b = 10.9481(11), c = 11.6722(12)A, β= 99.948(2)o, V = 1435.4(3)A3, Z = 2, Dc = 2.794 g/cm3, Mr = 1207.80,μ(MoKα) = 3.223 mm-1, F(000) = 1160, the final R = 0.0544 and wR = 0.1066 for 1906 observed reflections (I > 2σ(I)). Both compounds 1 and 2 adopt the Anderson structure, in which the anion is of centrosymmetry and formed by six octahedral edge-sharing MoO6 units surrounding the central MO6 (M = Mn or Co) octahedron.