Nano-silica and SiO2/CaCO3 nanocomposite prepared from semi-burned rice straw ash as modified papermaking fillers

Silica (SiO₂) nanoparticles and silica/calcium carbonate (SiO₂/CaCO₃) core–shell nanocomposites were prepared by sol–gel technique as fillers for papermaking application. Semi-burned rice straw ash (SBRSA), as waste material, was used to prepare the targeted fillers. Preparation of SiO₂ nanoparticles and SiO₂/CaCO₃ nanocomposites was carried out using Na₂SiO₃ solution that was prepared from SBRSA and CaCO₃ nanoparticles of 30–70 nm. The targeted SiO₂/CaCO₃ nanocomposites were prepared with different molar ratio of SiO₂:CaCO₃ 1:15, 1:10 and 1:5. The percentage of silica increased from 62.5% to 82.9% by thermal treatment of SBRSA at 800 °C for 2 h. The prepared SiO₂ nanoparticles and SiO₂/CaCO₃ nanocomposites were characterized by using XRD, XRF, TEM, FT-IR and Zeta potential. The results indicate that a pure semi-crystalline SiO₂ nanoparticle and semi-crystalline shell of SiO₂ coated CaCO₃ core particles were produced. The work extended also to investigate the effect of the prepared fillers on physical, mechanical and optical properties of paper.Application of the prepared SiO₂ nanoparticles and SiO₂/CaCO₃ nanocomposites improved the optical properties of paper (brightness, whiteness and opacity) but it slightly reduced the mechanical properties when compared to commercial precipitated CaCO₃ (PCC) filler.The results showed that the retention of SiO₂ nano-particles was highly increased. The retention of the prepared nanocomposites increased along with increasing of SiO₂:CaCO₃ molar ratio.     

Effect of different nanoparticles on thermal decomposition of poly(propylene sebacate)/nanocomposites: Evaluation of mechanisms using TGA and TG–FTIR–GC/MS

In the present study poly(propylene sebacate) (PPSeb) nanocomposites containing 2 wt% of fumed silica nanoparticles (SiO₂) or multiwalled carbon nanotubes (MWCNTs), or montmorillonite (MMT) were prepared by in situ polymerization. The thermal degradation of nanocomposites was studied using thermogravimetric analysis (TGA). It was found that the addition of MWCNTs and MMT enhances the thermal stability of the polymer, while SiO₂ nanoparticles do not affect it. From the variation of the activation energy (E) with increasing degree of conversion it was found that the decomposition of nanocomposites proceeded with a complex reaction mechanism with the participation of at least two different steps. To evaluate the thermal decomposition mechanisms and mainly the effect of nanoparticles on the thermal decomposition of PPSeb, TGA/FTIR and a combination of TG-gas chromatography–mass spectrometry (TG/GC–MS) were used. From mass ions detection of the formed decomposition compounds it was found that the decomposition of PPSeb and its nanocomposites, takes place mainly through β-hydrogen bond scission and, secondarily, through α-hydrogen bond scission. The main decomposition products were aldehydes, alcohols, allyl, diallyl, and carboxylic acids.     

Confined crystallization behaviors in polyethylene/silica nanocomposites: Synergetic effects of interfacial interactions and filler network

The confinement effects introduced by nanoparticles have been reported to influence the phase behaviors thus the properties of polymer nanocomposites. In this study, molecular dynamics and crystallization behaviors of polyethylene (PE) composited with three types of silica (SiO₂) nanoparticles, namely unmodified SiO₂, hydrophobically modified SiO₂, SiO₂‐APTES (3‐aminopropyltriethoxysilane) and SiO₂‐PTES (n‐propyltriethoxysilane), were systematically investigated via a combination of DSC, XRD and ¹H solid‐state NMR measurements. The suppressions in crystallization and chain mobilities of PE rank in the order of unmodified SiO₂ < SiO₂‐APTES < SiO₂‐PTES due to the increasing interfacial interactions between PE and SiO₂ nanoparticles. Additionally, independent of polymer–nanoparticle interactions, a silica network forms for all three kinds of nanocomposites when SiO₂ content reaches 83 wt %. The mobilities of polymer chains are severely restricted by such a percolated network structure, leading to a turning point in the crystallization ability of nanocomposites and a new crystallization peak at 45 °C lower than that of pure PE. The synergetic effects of interfacial interactions and filler network on polymer crystallization have been thoroughly studied in this work, which will provide guidance on modifying and designing nanocomposites with controlled properties. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 498–505     

Compatibilisation effect of PP-g-MA copolymer on iPP/SiO2 nanocomposites prepared by melt mixing

In the present study, a series of iPP/SiO₂ nanocomposites, containing 1, 2.5, 5, 7.5, 10 and 15 wt% SiO₂ nanoparticles, were prepared by melt mixing in a twin screw co-rotating extruder. Poly(propylene-g-maleic anhydride) copolymer (PP-g-MA) containing 0.6 wt% maleic anhydride content was added to all nanocomposites at three different concentrations, 1, 2.5 and 5 wt%, based on silica content. Mechanical properties such as tensile strength at break and Young’s modulus were found to increase and to be mainly affected by the content of silica nanoparticles as well as by the copolymer content. For the tensile strength at break as well as for yield point, a maximum was observed, corresponding to the samples containing 2.5-5 wt% SiO₂. At higher concentrations, large nanosilica agglomerates are formed that have as a result a decrease in tensile strength. Young’s modulus increases almost linearly on the addition of SiO₂, and takes values up to 60% higher than that of neat iPP. Higher concentrations of PP-g-MA resulted in a further enhancement of mechanical properties due to silica agglomerate reduction. This finding was verified from SEM and TEM micrographs. Evidently the surface silica hydroxyl groups of SiO₂ nanoparticles react with maleic anhydride groups of PP-g-MA and lead to a finer dispersion of individual SiO₂ nanoparticles in the iPP matrix. The enhanced adhesion in the interface of the two materials, as a result of the mentioned reaction, has been studied and proved by using several equations. The increased Vicat point of all nanocomposites, by increasing the PP-g-MA content, can also be mentioned as a positive effect.     

Enhancing mechanical and thermal properties of PLLA ligaments with fumed silica nanoparticles and montmorillonite

Nanocomposites of poly(l-lactic acid) (PLLA) containing 2.5 wt% of fumed silica nanoparticles (SiO₂) and organically modified montmorillonite (OMMT) were prepared by solved evaporation method. From SEM micrographs it was observed that both nanoparticles were well dispersed into PLLA matrix. All nanocomposites exhibited higher mechanical properties compared to neat PLLA, except elongation at break, indicating that nanoparticles can act as efficient reinforcing agents. Nanoparticles affect, also, the thermal properties of PLLA and especially the crystallization rate, which in all nanocomposites is faster than that of neat PLLA. From the thermogravimetric curves it can be seen that neat PLLA nanocomposites present a relatively better thermostability than PLLA, and this was also verified from the calculation of activation energy (E). From the variation of E with increasing degree of conversion it was found that PLLA/nanocomposites decomposition takes place with a complex reaction mechanism, with the participation of two different mechanisms. The combination of models, nth order and nth order with autocatalysis (Fn–Cn), for PLLA and PLLA/OMMT as well as the combination of Fn–Fn for PLLA/SiO₂ give the better results. For the PLLA/OMMT the values of the E for both mechanisms are higher than neat PLLA. For the PLLA/SiO₂ nanocomposite the value of the E is higher than the corresponding value for PLLA, for the first area of mass loss, while the E of the second mechanism has a lower value.     

Nanoflower-like composites of ZnO/SiO2 synthesized using bamboo leaves ash as reusable photocatalyst

In this study, the synthesis of ZnO/SiO₂ nanocomposites using bamboo leaf ash (BLA) and tested their photocatalytic activity for rhodamine B decolorization have been conducted. The nanocomposites were prepared by the sol–gel reaction of zinc acetate dihydrate, which was used as a zinc oxide precursor, with silica gel obtained from the caustic extraction of BLA. The effect of the Zn content (5, 10, and 20 wt%) on the physicochemical characteristics and photocatalytic activity of the nanocomposites was investigated. The results of X-ray diffraction, scanning electron microscopy, gas sorption, and transmission electron microscopy characterization confirmed the mesoporous structure of the composites containing nanoflower-like ZnO (wurtzite) nanoparticles of 10–30 nm in size dispersed on the silica support. Further, the nanocomposites were confirmed to be composed of ZnO/SiO₂ by X-ray photoelectron spectroscopy analysis. Meanwhile, diffuse-reflectance UV–visible spectrophotometry analysis of the nanocomposites revealed band gap energies of 3.38–3.39 eV. Of the tested nanocomposites, that containing 10 wt% Zn exhibited the highest decolorization efficiency (99%) and fastest decolorization rate. In addition, the degradation efficiencies were not reduced significantly after five repeated runs, demonstrating the reusability of the nanocomposite catalysts. Therefore, the ZnO/SiO₂ nanocomposite obtained from BLA is a promising reusable photocatalyst for the degradation of dye-polluted water.     

Enhancement of water barrier properties and tribological performance of hybrid glass fiber/epoxy composites with inclusions of carbon and silica nanoparticles

Water barrier properties and tribological performance (hardness and wear behavior) of new hybrid nanocomposites under dry and wet conditions were investigated. The new fabricated hybrid nanocomposite laminates consist of epoxy reinforced with woven and nonwoven tissue glass fibers and two different types of nanoparticles, silica (SiO₂) and carbon black nanoparticles (C). These nanoparticles were incorporated into epoxy resin as a single nanoparticle (either SiO₂ or C) or combining SiO₂ and C nanoparticles simultaneously with different weight fractions. The results showed that addition of carbon nanoparticles with 0.5 and 1 wt% resulted in maximum reduction in water uptake by 28.55% and 21.66%, respectively, as compared with neat glass fiber reinforced epoxy composites. Addition of all studied types and contents of nanoparticles improves hardness in dry and wet conditions over unfilled fiber composites. Under dry conditions, maximum reduction of 47.26% in weight loss was obtained with specimens containing 1 wt% carbon nanoparticles; however, in wet conditions, weight loss was reduced by 17.525% for specimens containing 0.5 wt% carbon nanoparticles as compared with unfilled fiber composites. Diffusion coefficients for different types of the hybrid nanocomposites were computed using Fickian and Langmuir models of diffusion. Copyright © 2017 John Wiley & Sons, Ltd.     

Cyanate Ester/Functionalized Silica Nanocomposite: Synthesis,Characterization and Properties

In this paper silica nanoparticles with covalently grafted polymer chains were incorporated into bisphenol A dicyanate ester (BADCy) to prepare composites which resulted in improvements in the mechanical and thermal properties. Fourier‐transform infrared (FT‐IR) spectroscopy transmission electron microscopy (TEM) and thermogravimetric analysis (TGA) were employed to examine the surface functionalization of silica nanoparticles. The effects of functionalized SiO₂ (F‐SiO₂) on the curing reactivity mechanical and thermal properties of BADCy resin were investigated systematically. The curing reaction of the system was facilitated with the addition of F‐SiO₂. Meanwhile compared with the neat resin the incorporation of appropriate content of modified F‐SiO₂ can enhance the mechanical properties including impact flexural strengths and fracture toughness K_IC of BADCy resin. In addition the thermal stability of BADCy/F‐SiO₂ nanocomposites is also superior to that of pure BADCy resin.     

Organic–inorganic polypyrrole‐surface modified SiO2 hybrid nanocomposites: a facile and green synthetic approach

Organic–inorganic hybrid nanocomposites composed of conductive polypyrrole (PPy) and surface modified silica (SiO₂) were successfully prepared through an in situ chemical oxidative polymerization in supercritical carbon dioxide (scCO₂). SiO₂ nanoparticles were surface modified using 3‐methacryloxypropyltrimethoxysilane (MPTMS) in order to disperse well in the medium. Transmission electron microscopy (TEM) and scanning electron microscopy (SEM) showed that the SiO₂ nanoparticles were encapsulated into the polymer. UV‐visible spectra of the diluted colloidal dispersions of PPy/SiO₂ hybrid nanocomposites were similar to those of PPy system. Fourier transform infrared spectroscopy (FT‐IR) suggested the strong interaction between PPy and SiO₂. Surface characterizations of nanocomposites were described by X‐ray photoelectron spectroscopy (XPS). The nanocomposites synthesized in scCO₂ have been shown to possess higher electrical conductivity and thermal stability. Copyright © 2009 John Wiley & Sons, Ltd.     

Ultrasonically assisted in situ emulsion polymerization: a facile approach to prepare conducting copolymer/silica nanocomposites

Ultrasonically assisted in situ emulsion polymerization was used to prepare electrically conducting copolymer poly(aniline‐co‐p‐phenylenediamine) [poly(Ani‐co‐pPD)] and silica (SiO₂) nancomposites. This approach can solve problems in the dispersion and stabilization of SiO₂ nanoparticles in the copolymer matrix. It was found that the aggregation of SiO₂ nanoparticles could be reduced under ultrasonic irradiation. Scanning transmission electron microscopy (STEM) confirmed that the resulting poly(Ani‐co‐pPD)/SiO₂ nanocomposite particles were spherical in shape, in which SiO₂ nanoparticles were well dispersed. The comonomer molecules were absorbed on the surface of SiO₂ particles and then polymerized to form core–shell nanocomposite. The incorporation of SiO₂ in the nanocomposite was supported by Fourier transform infrared spectroscopy (FT‐IR). UV‐visible spectra of the diluted colloid dispersion of nanocomposite particles were similar to those of the neat copolymer. Conductivity of nanocomposites was higher than the value obtained for the neat copolymer. Copyright © 2009 John Wiley & Sons, Ltd.     

Synthesis and characterization of Fe2O3/SiO2 nanocomposites

Fe₂O₃/SiO₂ nanocomposites based on fumed silica A-300 (S_BET = 337 m²/g) with iron oxide deposits at different content were synthesized using Fe(III) acetylacetonate (Fe(acac)₃) dissolved in isopropyl alcohol or carbon tetrachloride for impregnation of the nanosilica powder at different amounts of Fe(acac)₃ then oxidized in air at 400–900 °C. Samples with Fe(acac)₃ adsorbed onto nanosilica and samples with Fe₂O₃/SiO₂ including 6–17 wt% of Fe₂O₃ were investigated using XRD, XPS, TG/DTA, TPD MS, FTIR, AFM, nitrogen adsorption, Mössbauer spectroscopy, and quantum chemistry methods. The structural characteristics and phase composition of Fe₂O₃ deposits depend on reaction conditions, solvent type, content of grafted iron oxide, and post-reaction treatments. The iron oxide deposits on A-300 (impregnated by the Fe(acac)₃ solution in isopropanol) treated at 500–600 °C include several phases characterized by different nanoparticle size distributions; however, in the case of impregnation of A-300 by the Fe(acac)₃ solution in carbon tetrachloride only α-Fe₂O₃ phase is formed in addition to amorphous Fe₂O₃. The Fe₂O₃/SiO₂ materials remain loose (similar to the A-300 matrix) at the bulk density of 0.12–0.15 g/cm³ and S_BET = 265–310 m²/g.     

Characterisation of nickel–zinc ferrite/silica nanocomposites with low ferrite concentration obtained by an improved modified sol–gel method

The paper presents a study regarding the structure, morphology and magnetic behaviour of x% (Ni_0.65Zn_0.35Fe₂O₄)/(100 − x)% SiO₂ ferrimagnetic nanocomposites for low Ni–Zn ferrite concentration (x = 5, 10, 15, 20 and 30 mass percent) obtained by an improved modified sol–gel method. The obtained gels and nanocomposites have been characterized by fast Fourier transform-infrared (FT-IR) spectrometry, X-ray diffraction (XRD), transmission electron microscopy (TEM) and magnetic measurements (MM). The addition of a supplementary quantity of diol in the synthesis, corresponding to a molar ratio EG : TEOS = 1:1, and the control of the thermal treatment applied to the precursor xerogels tetraethylortosilicate (TEOS)–metal nitrates (MN)–ethylene glycol (EG) leads to fine (~2–9 nm), almost spherical Ni–Zn ferrite nanoparticles homogenously dispersed inside the amorphous SiO₂ matrix. TEM images reveal the fine nature and the narrow size distribution of the ferrite nanoparticles. Nanoparticles diameter increases with the ferrite concentration and with the annealing temperature. For all concentrations of ferrite in SiO₂ and all annealing temperature, we have obtained Ni_0.65Zn_0.35Fe₂O₄ ferrite as single phase (proven by XRD) in the amorphous silica matrix, only after a pre-treatment of synthesized gels, at 573 K, for 3 h. The magnetic behaviour of ferrite nanoparticles in quasi-static magnetic fields is very particular, depending on the annealing temperature and the ferrite content in silica matrix. We have obtained superparamagnetic behaviour for the nanocomposites, for a concentration of 30% ferrite in SiO₂ at high annealing temperature, of 1,273 K.     

Characterization of Fumed Alumina/Silica/Titania in the Gas Phase and in Aqueous Suspension

Fumed oxide alumina/silica/titania was studied in comparison with fumed alumina, silica, titania, alumina/silica, and titania/silica by means of XRD, ¹H NMR, IR, optical, dielectric relaxation, and photon correlation spectroscopies, electrophoresis, and quantum chemical methods. The explored Al₂O₃/SiO₂/TiO₂ consists of amorphous alumina (22 wt%), amorphous silica (28 wt%), and crystalline titania (50 wt%, with a blend of anatase (88%) and rutile (12%)) and has a wide assortment of Brønsted and Lewis acid sites, which provide a greater acidity than that of individual fumed alumina, silica, or titania and an acidity close to that of fumed alumina/silica or titania/silica. The changes in the Gibbs free energy (ΔG) of interfacial water in an aqueous suspension of Al₂O₃/SiO₂/TiO₂ are close to the ΔG values of the dispersions of pure rutile but markedly lower than those of alumina, anatase, or rutile covered by alumina and silica. The zeta potential of Al₂O₃/SiO₂/TiO₂ (pH of the isoelectric point (IEP) equals ≈3.3) is akin to that of fumed titania (pH(IEP_TiO2) ≈ 6) at pH > 6, but it significantly differs from the ζ of fumed alumina (pH(IEP_Al2O3) ≈ 9.8) at any pH value as well as those of fumed silica, titania/silica, and alumina/silica at pH < 6. The particle size distribution in the diluted aqueous suspensions of Al₂O₃/SiO₂/TiO₂ studied by means of photon correlation spectroscopy depends relatively slightly on pH in contrast to the titania/silica or alumina/silica dispersions. Theoretical calculations of oxide cluster interaction with water show a high probability of hydrolysis of Al–O–Ti and Si–O–Ti bonds strained at the interface of alumina/titania or silica/titania due to structural differences in the lattices of the corresponding individual oxides. Ab initio calculated chemical shift δ_H values of H atoms in different hydroxyl groups at the oxide clusters and in bound water molecules are in agreement with the ¹H NMR data and show a significant impact of charged particles (H₃O⁺ or OH⁻) on the average δ_H values of water droplets with (H₂O)_n at n between 2 and 48.     

Simultaneously toughening and reinforcing poly(lactic acid)/thermoplastic polyurethane blend via enhancing interfacial adhesion by hydrophobic silica nanoparticles

This work focuses on satisfactorily toughening and reinforcing poly(lactic acid)/thermoplastic polyurethane (PLA/TPU) blend with low TPU content (10 wt%) using appropriate amounts of hydrophobic silica nanoparticles (SiO₂) via simple melt mixing. Both thermodynamic prediction and transmission electron microscopy micrographs demonstrate that most SiO₂ nanoparticles distribute at interfaces between the PLA and TPU phases. This improves interfacial adhesion between the phases, which is attributed to good bonding strength between the PLA and SiO₂ via hydrophobic interaction and formation of hydrogen bonds between the TPU and SiO₂. The PLA/TPU (90/10) ternary blend nanocomposite with 2 wt% SiO₂ exhibits obviously high impact strength (about 5.0 and 12.6 times that of the corresponding blend and PLA, respectively) and higher tensile strength than the blend and even the PLA. Crazing is the main reason for improved impact toughnesses of the blend nanocomposites. This work provides a simple and effective strategy to endow PLA/elastomer blends with optimum strength–toughness balance by adding appropriate amounts of nanoparticles.     

Synthesis and characterization of poly1-hexene/silica nanocomposites

SiO₂ nano particles, with particle size of 12 nm, were first modified by substituting surface OH groups with O-hexyl moiety. Then, poly1-hexene/modified-SiO₂ composites with various nano-SiO₂ weight fractions were prepared by three different methods: in situ, solution, and melt methods and designated as PH-SiO₂/Insitu, PH-SiO₂/Sol and PH-SiO₂/Melt, respectively. PH-SiO₂/Insitu samples showed highly uniform particle dispersion up to 30 wt. % of silica while in PH-SiO₂/Sol and PH-SiO₂/Melt samples agglomeration of the silica nanoparticles occurred for filler contents ≥5 wt. % (i.e. 5, 10, 20 and 30 wt%). In the synthesized composites, the storage modulus significantly increased as high as 20.7 times when compared with neat poly1-hexene. Maximum decomposition temperature (T_max) and char yield at 600 °C increased with increasing silica level. Rheological results showed that G^ʹ> G^ʺ over the frequency range, illustrating the elastic behavior of the composite samples. In fact, samples showed the characteristic of a non-Newtonian fluid with a strong shear thinning effect in which η* increased with increasing filler weight fraction. From the results, it can be expected that modified silica could replace silica nanoparticles in polyolefin nanocomposite reinforcement.     

Low molecular weight aromatic compounds possessing a nonflammable characteristic in fluoroalkyl end‐capped acrylic acid oligomer/silica nanocomposite matrices after calcination at 800 °C under atmospheric conditions

Fluoroalkyl end‐capped acrylic acid oligomer [R_F‐(ACA)_n‐R_F] reacted with tetraethoxysilane and silica nanoparticles in the presence of low molecular weight aromatic compounds [ Ar‐H ] such as cetylpyridinium chloride (CPC) and bisphenol AF under alkaline conditions to afford R_F‐(ACA)_n‐R_F/SiO₂ nanocomposites‐encapsulated Ar‐H in 47–94% isolated yields. These fluorinated silica nanocomposites‐encapsulated Ar‐H can exhibit no weight loss behavior corresponding to the contents of Ar‐H after calcination at 800 °C under atmospheric conditions, although fluoroalkyl end‐capped acrylic acid oligomer in the nanocomposites decomposed completely under similar conditions. UV‐vis spectra of well‐dispersed methanol solutions of R_F‐(ACA)_n‐R_F/SiO₂/CPC nanocomposites before calcination show that CPC can be encapsulated into fluorinated silica nanocomposites with encapsulated ratios: 23–43%. The fluorinated nanocomposites after calcination was found to exhibit a higher antibacterial activity related to the presence of CPC in the composites. Encapsulated bisphenol AF into R_F‐(ACA)_n‐R_F/SiO₂ nanocomposites before and after calcination at 800 °C can exhibit a good releasing ability toward methanol with released ratios: 48 and 26%, respectively. ¹H MAS NMR, HPLC analysis, and LC‐MS spectra of R_F‐(ACA)_n‐R_F/silica nanocomposites‐encapsulated bisphenol AF also showed the presence of bisphenol AF in the nanocomposites even after calcination at 800 °C under atmospheric conditions. These findings suggest that CPC and bisphenol AF can exhibit a nonflammable characteristic in the fluorinated silica nanocomposites. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Optimizing Melt‐Processing Conditions for the Preparation of iPP/Fumed Silica Nanocomposites: Morphology,Mechanical and Gas Permeability Properties

A series of iPP/SiO₂ nanocomposites, containing 1, 2.5, 5, 7.5, and 10 wt.‐% fumed silica nanoparticles, were prepared by melt mixing in a twin screw co‐rotating extruder. The effect of different extrusion parameters was evaluated. The size of aggregates increased with increase in SiO₂ content and repetition of the mixing process improved the filler's dispersion. A similar effect was also exhibited by either increasing the rotor speed or the mixing temperature, with the latter being more pronounced at the ranges studied. The mechanical properties of the prepared nanocomposites were evaluated and various models used to explain the observed enhancements. However, only the three‐phase model could provide some correlation with the experimental results. All nanocomposites displayed lower permeability to gases.

     

Synthesis and characterization of high surface area TiO2/SiO2 mesostructured nanocomposite

Recently titania synthesis was reported using various structuration procedures, leading to the production of solid presenting high surface area but exhibiting moderate thermal stability. The study presents the synthesis of TiO₂/SiO₂ nanocomposites, a solid that can advantageously replace bulk titania samples as catalyst support. The silica host support used for the synthesis of the nanocomposite is a SBA-15 type silica, having a well-defined 2D hexagonal pore structure and a large pore size. The control of the impregnation media is important to obtain dispersed titania crystals into the porosity, the best results have been obtained using an impregnation in an excess of solvent. After calcination at low temperature (400 °C), nanocomposites having titania nanodomains (～2–3 nm) located inside the pores and no external aggregates visible are obtained. This nanocomposite exhibits high specific surface area (close to that of the silica host support, even with a titania loading of 55 wt.%) and a narrow pore size distribution. Surprisingly, the increase in calcination temperature up to 800 °C does not allow to detect the anatase to rutile transition. Even at 800 °C, the hexagonal mesoporous structure of the silica support is maintained, and the anatase crystal domain size is evaluated at ～10 nm, a size close to that of the silica host support porosity (8.4 nm). Comparison of their physical properties with the results presented in literature for bulk samples evidenced that these TiO₂/SiO₂ solids are promising in term of thermal stability.     

(Co)polyimides from commonly used monomers, and their nanocomposites

Synthesis of (co)polyimides from aromatic dianhydrides (pyromellitic dianhydride (PMDA), symmetric 3,3′,4,4′-biphenyltetracarboxylic dianhydride (sBPDA)) and diamines (4,4′-oxydianiline (ODA), p-phenylenediamine (PDA)) commonly used for the production of commercial polyimides, as well as the preparation of their nanocomposites with SiO₂ nanoparticles were performed with the aim to find ways to control technical performance of polyimides. The (co)polyimide films prepared under mild thermal imidization conditions were analyzed by FTIR, WAXD, DSC and TG, and characterized by transition temperatures and the temperatures of 5% and 10% mass loss, as well as tensile parameters.Films of PMDA/sBPDA–ODA copolyimides at the ambient temperature had a 20% higher ultimate strength and exhibited a higher tensile modulus than the reference polyimide (PMDA–ODA). However, lowering the transition temperature of the polyimide by partial substitution of an sBPDA monomeric unit for PMDA resulted in lowering the modulus at higher temperatures. The best performance was exhibited by semi-crystalline films of sBPDA–ODA/PDA copolyimide, which had a 35% higher ultimate strength and a 64% higher elongation at break at the ambient temperature than the reference polyimide (sBPDA–PDA), and also retained the strength and exhibited a 200% higher elongation at a temperature of 200 °C.Unexpectedly, the elongation at break of PMDA–ODA based (co)polyimide nanocomposites with hydrophobic SiO₂ nanoparticles was greater than that of the baseline (co)polyimides. It was neither the case with PMDA–ODA nanocomposites with hydrophilic SiO₂ nanoparticles, nor with sBPDA–PDA (co)polyimide based nanocomposites with hydrophobic SiO₂ nanoparticles.     

Infiltration of SiO<Subscript>2</Subscript>/SiOC Nanocomposites by a Multiple Sol Infiltration-Pyrolysis Process

SiO₂ containing hybrid inorganic-organic nanocomposites prepared by the sol-gel method from silica nanoparticles, tetraethylorthosilicate and silanol terminated polydimethylsiloxane were used as precursors for obtaining porous SiO₂/SiOC nanocomposites by pyrolysis in nitrogen atmosphere. A tetraethylorthosilicate sol and a triethoxysilane/methyldiethoxysilane sol, prepared by the sol-gel method and investigated by FT-IR, were used for a multiple sol infiltration-pyrolysis process in vacuum as precursors for a secondary SiO₂ and SiOC glassy phase respectively. As the density and porosity of these materials depends on the starting precursor composition, the sol infiltration-pyrolysis process was carried out in order to decrease the porosity and increase the density of such materials. This process was monitored using the sample weight gain and by a non-destructive method for measuring of the E modulus on each cycle. The initial and final material was also characterized by means of Hg porosimetry and the three-point bend test, at room temperature, of the nanocomposites was also examined.