An intimate polycarbonate/poly(methyl methacrylate)/poly(vinyl acetate) ternary blend via coalescence from their common inclusion compound with γ‐cyclodextrin

In this study, we successfully report an intimate ternary blend system of polycarbonate (PC)/poly(methyl methacrylate) (PMMA)/poly(vinyl acetate) (PVAc) obtained by the simultaneous coalescence of the three guest polymers from their common γ‐cyclodextrin (γ‐CD) inclusion compound (IC). The thermal transitions and the homogeneity of the coalesced ternary blend were studied by differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). The observation of a single, common glass transition strongly suggests the presence of a homogeneous amorphous phase in the coalesced ternary polymer blend. This was further substantiated by solid‐state ¹³C NMR observation of the T_1ρ(¹H)s for each of the blend components. For comparison, ternary blends of PC/PMMA/PVAc were also prepared by traditional coprecipitation and solution casting methods. TGA data showed a thermal stability for the coalesced ternary blend that was improved over the coprecipitated blend, which was phase‐segregated. The presence of possible interactions between the three polymer components was investigated by infrared spectroscopy (FTIR). The analysis indicates that the ternary blend of these polymers achieved by coalescence from their common γ‐CD–IC results in a homogeneous polymer blend, possibly with improved properties, whereas coprecipitation and solution cast methods produced phase separated polymer blends. It was also found that control of the component polymer molar ratios plays a key role in the miscibility of their coalesced ternary blends. Coalescence of two or more normally immiscible polymers from their common CD–ICs appears to be a general method for obtaining well‐mixed, intimate blends. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 4182–4194, 2004     

Poly(ether ether ketone)/poly(aryl ether sulfone) blends: Melt rheological behavior

Dynamic rheological measurements were carried out on blends of poly(ether ether ketone) (PEEK)/poly(aryl ether sulfone) (PES) in the melt state in the oscillatory shear mode. The data were analyzed for the fundamental rheological behavior to yield insight into the microstructure of PEEK/PES blends. A variation of complex viscosity with composition exhibited positive–negative deviations from the log‐additivity rule and was typical for a continuous‐discrete type of morphology with weak interaction among droplets. The point of transition showed that phase inversion takes place at composition with a 0.6 weight fraction of PEEK, which agreed with the actual morphology of these blends observed by scanning electron microscopy. Activation energy for flow, for blend compositions followed additive behavior, which indicated that PEEK/PES blends may have had some compatibility in the melt. Variation of the elastic modulus (G′) with composition showed a trend similar to that observed for complex viscosity. A three‐zone model used for understanding the dynamic moduli behavior of polymers demonstrated that PEEK follows plateau‐zone behavior, whereas PES exhibits only terminal‐zone behavior in the frequency range studied. The blends of these two polymers showed an intermediate behavior, and the crossover frequency shifted to the low‐frequency region as the PEEK content in PES increased. This revealed the shift of terminal‐zone behavior to low frequency with an increased PEEK percentage in the blend. Variation of relaxation time with composition suggested that slow relaxation of PEEK retards the relaxation process of PES as the PEEK concentration in the blend is increased because of the partial miscibility of the blend, which affects the constraint release process of pure components in the blend. A temperature‐independent correlation observed in the log–log plots of G′ versus loss modulus (G″) for different blend systems fulfilled the necessary condition for their rheological simplicity. Further, the composition‐dependent correlations of PEEK/PES blends observed in a log–log plot of G′ versus G″ showed that the blends are either partially miscible or immiscible and form a discrete‐continuous phase morphology. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1548–1563, 2004     

Miscibility and phase structure of binary blends of polylactide and poly(methyl methacrylate)

Blends of amorphous poly(DL‐lactide) (DL‐PLA) and crystalline poly(L‐lactide) (PLLA) with poly(methyl methacrylate) (PMMA) were prepared by both solution/precipitation and solution‐casting film methods. The miscibility, crystallization behavior, and component interaction of these blends were examined by differential scanning calorimetry. Only one glass‐transition temperature (T_g) was found in the DL‐PLA/PMMA solution/precipitation blends, indicating miscibility in this system. Two isolated T_g's appeared in the DL‐PLA/PMMA solution‐casting film blends, suggesting two segregated phases in the blend system, but evidence showed that two components were partially miscible. In the PLLA/PMMA blend, the crystallization of PLLA was greatly restricted by amorphous PMMA. Once the thermal history of the blend was destroyed, PLLA and PMMA were miscible. The T_g composition relationship for both DL‐PLA/PMMA and PLLA/PMMA miscible systems obeyed the Gordon–Taylor equation. Experiment results indicated that there is no more favorable trend of DL‐PLA to form miscible blends with PMMA than PLLA when PLLA is in the amorphous state. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 23–30, 2003     

Thermoplastic blend demixing by a high‐pressure,high‐temperature process

The analysis of a thermoplastic polymer blend requires a precise separation of the blend components, which is usually performed by selective solvent extraction. However, when the components are high‐molecular‐weight polymers, a complete separation is very difficult. The use of fluids in near critical and supercritical conditions becomes a promising alternative to reach a much more precise separation. In this work, a method to separate reactive and physical blends from high‐molecular‐weight commercial polymers is proposed. Polyethylene (PE)/polystyrene (PS) blends were separated into their components with n‐propane, n‐pentane, and n‐heptane at near critical and supercritical conditions. The selectivity of each solvent was experimentally studied over a wide range of temperatures for assessing the processing windows for the separation of pure components. The entire PE phase was solubilized by n‐pentane and n‐heptane at similar temperatures, whereas propane at supercritical conditions could not dissolve the fraction of high‐molecular‐weight PE. The influence of the blend morphology and composition on the efficiency of the polymer separation was studied. In reactive blends, the in situ copolymer formed was solubilized with the PE phase by chemical affinity. The method proposed for blend separation is easy, rapid, and selective and seems to be a promising tool for blend separation, particularly for reactive blends, for which the isolation of the copolymer is essential for characterization © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 2361–2369, 2005     

Miscibility level and mechanical characterization of blends of two liquid‐crystalline polymers based on p‐hydroxybenzoic acid

Injection‐molded blends composed of two liquid‐crystalline polymers (LCPs) based on 60/40 p‐hydroxybenzoic acid/ethylene terephthalate (R3) and 73/27 p‐hydroxybenzoic acid/2,6‐hydroxynaphthoic acid (VA) copolymers, respectively, were obtained across the whole composition range. The two amorphous phases of the blends contained only slight amounts of the minority component, and the occurrence of some chemical reaction, mainly at high VA contents, was detected by Fourier transform infrared. Synergisms in the modulus of elasticity and in the tensile strength were seen in most of the blend compositions. The largest synergism was in the 50/50 R3/VA blend, which showed a modulus of elasticity 26% higher than that of either of the two components and a 17% positive deviation in the tensile strength with respect to the rule of mixtures. The different orientation of the LCPs in the blends explains the differences in the mechanical behavior. However, contrary to previous works on LCP blends and despite the almost complete immiscibility, the observed negative volume of mixing appears to be the main parameter that determines the synergistic mechanical behavior. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1022–1032, 2003     

Thermal characterization of polycarbonate/polycaprolactone blends

In this work, we prepared blends of bisphenol A polycarbonate (PC) and poly(ϵ‐caprolactone) (PCL) in a wide composition range by melt mixing and solution mixing. Two different molecular weights of PCL were used (nominally, 10.000 g/mol, PCL10, and 80.000 g/mol, PCL80). The thermal behavior of both systems was studied via differential scanning calorimetry under dynamic and isothermal conditions. The blends were miscible in the entire composition range in the liquid and amorphous states, as indicated by the single glass‐transition temperature (T_g) exhibited by both the PC/PCL10 and PC/PCL80 blends. The compositional variation of the T_g was accurately described by the Fox equation for the PC/PCL80 blends, whereas slight deviations from this equation were exhibited by the PC/PCL10 blends. For blend compositions containing 40% or more PCL, either one or both blend components crystallized. Crystallization occurred during cooling from the melt or during subsequent heating in the form of cold crystallization. Although PCL crystallization was reduced and its crystallization rate decreased with the addition of PC, PCL was a very effective macromolecular plasticizer for PC, to the extent that crystallization during the scan was detected for some blend compositions. Isothermal crystallization experiments allowed the determination of equilibrium melting points (T) by the Hoffman–Weeks extrapolation method. A T depression was found for both PCL and PC components as the content of the other blend component was increased. The Avrami equation was closely obeyed by both blend components during the isothermal overall crystallization kinetics up to crystalline conversion degrees of 60–70% and with values of Avrami indices ranging from 3 to 4, depending on the crystallization temperature employed. © 2001 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 39: 771–785, 2001     

Thermal,morphology, and NMR characterizations on phase behavior and miscibility in blends of isotactic polystyrene with poly(cyclohexyl methacrylate)

The miscibility and phase behavior in a binary blend of isotactic polystyrene (iPS) and poly(cyclohexyl methacrylate) (PCHMA) were investigated by differential scanning calorimetry, optical microscopy (OM), and solid‐state ¹³C cross‐polarity/magic‐angle spinning NMR. The iPS/PCHMA blend was miscible when all compositions showed a single composition‐dependent glass‐transition temperature (T_g) and when the blend went through a thermodynamic phase transition upon heating to above the lower critical solution temperature as determined by OM measurements. The ¹H NMR spin‐relaxation times in the laboratory frame (T) and in the rotating frame (T) for iPS/PCHMA blends with various compositions and neat components were directly measured through solid‐state¹³C NMR. The results of T indicated that the blends are homogeneous, at least on a scale of 75–85 nm, confirming the miscibility of the system. The single decay and composition‐dependent T values for each blend further demonstrated the blends are homogeneous on a scale of 2.5–3.5 nm. The results suggested that iPS and PCHMA are intimately mixed at the molecular level within the blends at all compositions. The tacticity of polystyrene does not seem to adversely influence the miscibility in blends of iPS/PCHMA. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 772–784, 2003     

Local compositional fluctuations in PPO/HIPSand PPO/SBS blends

Solid-state NMR relaxation has been used to explore the distribution of components in poly(phenylene oxide) (PPO) high impact polystyrene (HIPS) and PPO/poly(styrene-b-butadiene-b-styrene) (SBS) blends. The nuclear relaxation of PPO in the former system is single exponential for all compositions, but the relaxation of PS in the blend is simple exponential only when the PPO content is low but is otherwise nonexponential. The nuclear magnetization decay curves were analyzed in terms of statistical compositional fluctuation at the scale of spin diffusion distances of several nm. Distribution functions for nuclear relaxation and for blend composition have been derived. Extraction of low molecular weight occluded PS from HIPS resulted in blends having reduced homogeneity. Addition of low molecular weight PS enhanced homogeneity in both the PPO/HIPS and PPO/SBS blends. © 1994 John Wiley & Sons, Inc.     

Thermal,crystallization, mechanical,and rheological characteristics of poly(trimethylene terephthalate)/poly(ethylene terephthalate) blends

Blends of poly(trimethylene terephthalate) (PTT) and poly(ethylene terephthalate) in the amorphous state were miscible in all of the blend compositions studied, as evidenced by a single, composition‐dependent glass‐transition temperature observed for each blend composition. The variation in the glass‐transition temperature with the blend composition was well predicted by the Gordon–Taylor equation, with the fitting parameter being 0.91. The cold‐crystallization (peak) temperature decreased with an increasing PTT content, whereas the melt‐crystallization (peak) temperature decreased with an increasing amount of the minor component. The subsequent melting behavior after both cold and melt crystallizations exhibited melting point depression behavior in which the observed melting temperatures decreased with an increasing amount of the minor component of the blends. During crystallization, the pure components crystallized simultaneously just to form their own crystals. The blend having 50 wt % of PTT showed the lowest apparent degree of crystallinity and the lowest tensile‐strength values. The steady shear viscosity values for the pure components and the blends decreased slightly with an increasing shear rate (within the shear rate range of 0.25–25 s^?1); those of the blends were lower than those of the pure components. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 676–686, 2004     

Control of phase separation behavior of PC/PMMA blends and their application to the gas separation membranes

Gas transport and thermodynamic properties for the blends of polycarbonate (PC) and polymethylmethacrylate (PMMA) were studied. To explore glass transition temperatures of blends and their phase separation temperatures due to a lower critical solution temperature, LCST, a type of phase boundary, transparent blend films that are miscible and do not contain solvent-induced PC crystals were prepared by controlling molecular weights of each component. The average value of interaction energy densities between PC and PMMA obtained from the phase boundaries and the equation of a state theory based on the lattice fluid model was 0.04 cal/cm³. This result confirmed that miscibility of PC and PMMA blends at equilibrium depends upon the molecular weights of components. Gas transport properties of miscible blends and immiscible blends having the same chemical components and composition but a difference in morphology were examined at 35°C and 1 atm for the gases N₂ and O₂. Permeability and apparent diffusion coefficients were ranked in the order of the immiscible blend having a domain–matrix structure > the immiscible blend having an interconnected structure > the miscible blend. These results might be related to the differences in the local chain motions that depend on the intermolecular mixing level. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 2950–2959, 1999     

Biodiesel from soybean oil,castor oil and their blends

Even not being described in the EN 14112 standard, PDSC has been used for the determination of the biodiesel oxidative stability, by OIT and OT measurements. In this study, biodiesel blends were obtained by mixing soybean (BES) and castor (BEM) ethyl esters and its induction periods were measured by Rancimat and PDSC. The blends (BSM _X ) showed intermediate values of OSI, OT, and OIT, compared with BES and BEM. Although, the molar fraction of the components varied linearly in BSM _X , OSI, OT, and OIT values increased exponentially in relation to the castor biodiesel amount in the blends. Introduction of castor oil biodiesel increased the blend stability, so the BSM₃₀ blend reached the OSI limit of 6 h. OSI, OIT, and OT showed a high-linear correlation, pointing out that PDSC can be used in the analysis of this kind of biodiesel, with a smaller sample and analysis time, as compared to Rancimat. The use of biodiesel blends was a good alternative in the correction of the oxidative stability of the final product without the need of antioxidant addition.     

Phase separation,porous structure,and cure kinetics in aliphatic epoxy resin containing hyperbranched polyester

Thermosetting blends of an aliphatic epoxy resin and a hydroxyl‐functionalized hyperbranched polymer (HBP), aliphatic hyperbranched polyester Boltorn H40, were prepared using 4,4′‐diaminodiphenylmethane (DDM) as the curing agent. The phase behavior and morphology of the DDM‐cured epoxy/HBP blends with HBP content up to 40 wt % were investigated by differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), and scanning electron microscopy (SEM). The cured epoxy/HBP blends are immiscible and exhibit two separate glass transitions, as revealed by DMA. The SEM observation showed that there exist two phases in the cured blends, which is an epoxy‐rich phase and an HBP‐rich phase, which is responsible for the two separate glass transitions. The phase morphology was observed to be dependent on the blend composition. For the blends with HBP content up to 10 wt %, discrete HBP domains are dispersed in the continuous cured epoxy matrix, whereas the cured blend with 40 wt % HBP exhibits a combined morphology of connected globules and bicontinuous phase structure. Porous epoxy thermosets with continuous open structures on the order of 100–300 nm were formed after the HBP‐rich phase was extracted with solvent from the cured blend with 40 wt % HBP. The DSC study showed that the curing rate is not obviously affected in the epoxy/HBP blends with HBP content up to 40 wt %. The activation energy values obtained are not remarkably changed in the blends; the addition of HBP to epoxy resin thus does not change the mechanism of cure reaction of epoxy resin with DDM. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 889–899, 2006     

Dynamic Mechanical Thermal Analysis of Polyamide 6/Biopol Blends

The temperature dependence investigated by means of DMTA of dynamic storage modulusE′, dynamic loss modulus E″ and loss tangent tgδ of blends obtained from polyamide 6 and poly(β-hydroxybutyrate-co-β-hydroxyvalerate) (Biopol D600G) indicated, that the dynamic mechanical properties of the blends containing up to 40% Biopol D600G are governed by the properties of polyamide 6. First at the 50% Biopol D600G content in the blend the transitions of the Biopol phase become visible and dominant. The shifts of the loss modulus maxima of the blends might indicate some interactions between the blend components in the amorphous phase. This revised version was published online in August 2006 with corrections to the Cover Date.     

Morphology,structure, and properties of in situ compatibilized linear low‐density polyethylene/polystyrene and linear low‐density polyethylene/high‐impact polystyrene blends

Blends of linear low‐density polyethylene (LLDPE) with polystyrene (PS) and blends of LLDPE with high‐impact polystyrene (HIPS) were prepared through a reactive extrusion method. For increased compatibility of the two blending components, a Lewis acid catalyst, aluminum chloride (AlCl₃), was adopted to initiate the Friedel–Crafts alkylation reaction between the blending components. Spectra data from Raman spectra of the LLDPE/PS/AlCl₃ blends extracted with tetrahydrofuran verified that LLDPE segments were grafted to the para position of the benzene rings of PS, and this confirmed the graft structure of the Friedel–Crafts reaction between the polyolefin and PS. Because the in situ generated LLDPE‐g‐PS and LLDPE‐g‐HIPS copolymers acted as compatibilizers in the relative blending systems, the mechanical properties of the LLDPE/PS and LLDPE/HIPS blending systems were greatly improved. For example, after compatibilization, the Izod impact strength of an LLDPE/PS blend (80/20 w/w) was increased from 88.5 to 401.6 J/m, and its elongation at break increased from 370 to 790%. For an LLDPE/HIPS (60/40 w/w) blend, its Charpy impact strength was increased from 284.2 to 495.8 kJ/m². Scanning electron microscopy micrographs showed that the size of the domains decreased from 4–5 to less than 1 μm, depending on the content of added AlCl₃. The crystallization behavior of the LLDPE/PS blend was investigated with differential scanning calorimetry. Fractionated crystallization phenomena were noticed because of the reduction in the size of the LLDPE droplets. The melt‐flow rate of the blending system depended on the competition of the grafting reaction of LLDPE with PS and the degradation of the blending components. The degradation of PS only happened during the alkylation reaction between LLDPE and PS. Gel permeation chromatography showed that the alkylation reaction increased the molecular weight of the blend polymer. The low molecular weight part disappeared with reactive blending. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1837–1849, 2003     

Miscibility enhancement in blends of polystyrene and polyisoprene modified with electron donor–electron acceptor groups

The use of electron donor–electron acceptor groups to enhance miscibility in polymer blends has been investigated, using the immiscible binary pair polystyrene and polyisoprene as the basic materials. These polymers have been modified by copolymerization with monomers that are either donor or acceptor groups. The copolymers synthesized were poly(styrene-stat-N-itaconimidyl-3,5-dinitrobenzoate), which contains the electron acceptor, and poly[isoprene-stat-N-(2-hydroxyethyl) carbazole methacrylate], which contains the electron donor. Blends were examined using differential scanning calorimetry and dynamic mechanical thermal analysis. The criterion of miscibility was taken to be the presence of only one glass transition temperature in the binary blend, and it was established that at least 20 mol% of the donor–acceptor units had to be incorporated into each chain before a stable one-phase blend was obtained. Miscible blends were observed to undergo a “decomplexation” reaction above the blend T_g, to form partially phase separated blends, with each phase rich in one component and diluted by the second. The value of the blend T_g was above that expected from a weighted average of those of the components, indicating that specific intermolecular interactions, probably charge-transfer complexes, which led to nonbonding crosslinking were present in the blend and stabilized the one-phase system.     

In‐line monitoring of immiscible polymer blends in a rheometer with a fiber‐optics‐assisted fluorescence detection system

In‐line studies of the initial stages of shear‐induced coalescence in two‐phase polymer blends were carried out with a home‐built device combining a cone and plate rheometer and a fiber‐optic‐assisted fluorescence detection system. A blend of 90 wt % poly(2‐ethylhexyl methacrylate) (PEHMA) and 10 wt % poly(butyl methacrylate) (PBMA) was prepared by the casting of films onto a solid substrate from mixed aqueous latex dispersions of the two polymers. The dispersions were prepared via emulsion polymerization under conditions in which both components were formed as spherical particles with a very narrow size distribution. By using a 14:1 particle ratio of PEHMA to PBMA, we obtained films in which 120‐nm PBMA particles were surrounded by a PEHMA matrix. The blend contained phenanthrene‐labeled PBMA particles and anthracene‐labeled PBMA particles in a ratio of 4:1, whereas the PEHMA matrix polymer was unlabeled. We monitored the anthracene‐to‐phenanthrene fluorescence intensity ratio (I₄₇₀/I₃₆₀) as a measure of direct nonradiative energy transfer from phenanthrene to anthracene, whereas the blend was sheared at different shear rates and temperatures. Under no‐shear conditions, the results of in‐line experiments were in good agreement with the results of off‐line measurements of energy transfer by conventional techniques. In blends under shear, the two sets of experiments, in‐line and off‐line, did not agree with each other. The cause of this disagreement was associated with normal forces in the blend under shear that affected the optical path length and the relative intensities of the fluorescence signals of the phenanthrene and anthracene groups in the blend. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 2302–2316, 2001     

Blends of polycarbonate and poly(ϵ‐caprolactone) and the determination of the polymer–polymer interaction parameter of the two polymers

The thermal properties of blends of polycarbonate (PC) and poly(ε‐caprolactone) (PCL) were investigated by differential scanning calorimetry (DSC). From the thermal analysis of PC‐PCL blends, a single glass‐transition temperature (T_g) was observed for all the blend compositions. These results indicate that there is miscibility between the two components. From the modified Lu and Weiss equation, the polymer–polymer interaction parameter (χ₁₂) of the PC‐PCL blends was calculated and found to range from −0.012 to −0.040 with the compositions. The χ₁₂ values calculated from the T_g method decreased with the increase of PC weight fraction. By taking PC‐PCL blend as a model system, the values of χ₁₂ were compared with two different methods, the T_g method and melting point depression method. The two methods are in reasonably good agreement for the χ₁₂ values of the PC‐PCL blends. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 2072–2076, 2000     

Surface tension of polystyrene blends: Theory and experiment

Surface tension of linear–linear and star/linear polystyrene blends were measured using a modified Wilhelmy method. Our results show that for both polystyrene blend systems, the surface tension‐composition profile is convex, indicating a strong surface excess of the component with lower surface energy. Star/linear blends display more convex surface tension profiles than their linear–linear counterparts, indicative of stronger surface segregation of the branched‐component relative to linear chains. As a first step toward understanding the physical origin of enhanced‐surface segregation of star polymers, self‐consistent field (SCF) lattice simulations (both incompressible and compressible models) and Cahn‐Hilliard theory were used to predict surface tension‐composition profiles. Results from the lattice simulations indicate that the highly convex surface tension profiles observed in the star/linear blend systems are only possible if an architecture‐dependent, Flory interaction parameter (χ = 0.004) is assumed. This conclusion is inconsistent with results from bulk differential scanning calorimetry (DSC) measurements, which indicate sharp glass transitions in both the star/linear and linear/linear homopolymer blends and a simple linear relationship between the bulk glass transition temperature and blend composition. To implement the Cahn‐Hilliard theory, pressure‐volume‐temperature (PVT) data for each of the pure components in the blends were first measured and the data used as input for the theory. Consistent with the experimental data, Cahn‐Hilliard theory predicts a larger surface excess of star molecules in linear hosts over a wide composition range. Significantly, this result is obtained assuming a nearly neutral interaction parameter between the linear and star components, indicating that the surface enrichment of the stars is not a consequence of complex phase behavior in the bulk. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 1666–1685, 2009     

Control of droplet size of polymer–diluent blends through thermally induced phase separation

The effects of process conditions and molecular structure of polymer and diluent on the droplet size of membranes formed by thermally induced phase separatiom (TIPS) process were examined. The observed upper critical solution temperature–type phase boundaries of nylon‐12 blended with poly(ethylene glycol) (PEG) and nylon 12 diluted with poly(ethylene glycol) dimethyl ether (PEGDE) and their interaction energy densities calculated using the Flory–Huggins theory suggest that the nylon‐12/PEGDE blends are less stable than the nylon‐12–PEG blends. Infrared spectra confirmed that the difference in phase stability might come from specific interactions of the hydroxyl terminal groups of PEG with the amide groups from nylon‐12, which are not be feasible in the nylon‐12–PEGDE blends. The phase stability of diluent PEG blended with various nylons that are different in the number of methyl groups in the repeat unit was ranked in the order of: nylon‐6–PEG blend < nylon‐12–PEG blend < nylon‐11–PEG blend. We also noted that the phase‐separated droplets grew by both coalescence and the Oswald ripening process after the onset of phase separation. As a result, the cubic exponent of average droplet radius (R³) plotted against time satisfied the linear relationship. As the blends became less stable, the droplet growth rate increased and larger equilibrium droplets formed at a constant quenching depth. The TIPS membranes with desired pore structure could be prepared by controlling the molecular structure of components as well as by varying processing conditions such as quenching depth and annealing time. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 3042–3052, 2000     

Physical properties and phase separation structure of Antheraea pernyi/Bombyx mori silk fibroin blend films

The physical structure and compatibility of solution-cast Antheraea pernyi/Bombyx mori silk fibroin blend films were stuided by differential scanning calorimetry (DSC), thermomechanical (TMA) and thermogravimetric (TGA) analysis, dynamic viscoelastic measurement, infrared spectroscopy, and x-ray diffractometry. The DSC curves of the blend films showed independent endotherms at 280 and 358°C, corresponding to the thermal decomposition of B. mori and A. pernyi silk fibroins with random coil conformation. The intensity was roughly proportionate to the amount of each component in the blend. The thermal behavior corresponding to the conformational transitions induced by heating on A. pernyi and B. mori silk fibroins overlapped in the temperature range 190–230°C. Thermal expansion and contraction properties, as well as weight retention behavior of the blend films were intermediate between the pure components, as shown by the TMA and TGA curves. The onset temperature of the storage modulus curve decreased markedly, approaching that of B. mori silk fibroin film when the amount of this component in the blend increased. The loss modulus curve of the blend films showed two peaks at ca. 190 and 210°C, the former corresponding to B. mori, and the latter to A. pernyi silk fibroin. Infrared spectra of the blends exhibited absorption bands characteristic of the pure components overlapping in the spectral region 2000–400 cm^?1. The x-ray diffraction peaks at 23 and 21.5°, attributed to the crystalline spacings of A. pernyi and B. mori fibroins, respectively, overlapped in the diffraction curves of the blends, while the peak at 11.4°, of A. pernyi, increased as the content of this fibroin in the blend increased. The degree of crystallinity, calculated from the x-ray diffraction curves, diminished as the amount of B. mori silk fibroin decreased. A low degree of compatibility exists between the two fibroins when they are cast from aqueous solution in the experimental conditions adopted in this work. © 1994 John Wiley & Sons, Inc.