含亚胺结构新型磷-氮协效阻燃化合物的合成及对环氧树脂的阻燃作用

采用醛胺缩合反应,以4-(5,5-二甲基-1,3-二氧杂环己内磷酰基)苯甲醛(PCHO)分别与对苯二胺、乙二胺反应合成两种磷酸酯-亚胺双官能化合物阻燃剂(FR:N¹,N⁴-二[4-(5,5-二甲基-1,3-二氧杂环己内磷酰氧基)苯基亚甲基]-1,4-苯二胺(PNB)和N¹,N²-二[4-(5,5-二甲基-1,3-二氧杂环己内磷酰氧基)苯基亚甲基]-1,2-乙二胺(PNE)),研究了FR对4,4'-二氨基二苯砜(DDS)固化双酚A二缩水甘油醚型环氧树脂(DGEBA)体系的阻燃作用及阻燃机理。 研究发现FR的引入显著提高了DGEBA/DDS在700 ℃时的残炭率(R_c),同时提升了材料的阻燃性能,其中以乙二胺合成的PNE阻燃性能显著优于以苯二胺合成的PNB。 当磷添加质量分数为1.5%时,PNE-1.5/DGEBA/DDS在N₂气下的R_c为35.1%,在空气下的R_c为14.4%,极限氧指数(LOI)为33.2%,并可达阻燃等级UL-94最高阻燃级别V-0级。 同时,PNE-1.5/DGEBA/DDS相较于DGEBA/DDS保持了弯曲强度和76%以上的冲击强度,机械性能显著优于PNB-1.5/DGEBA/DDS。 通过阻燃机理分析FR在DGEBA/DDS体系中具有凝聚相、气相及磷-氮协效共同作用的阻燃特点。 磷酸酯-亚胺双官能团化合物FR对环氧树脂体系具有良好的阻燃作用,其中PNE阻燃效率高、机械性能负面影响小,具有潜在应用价值。     

氧化石墨烯与Si-P低聚物在环氧树脂中的协同阻燃作用

采用Hummers方法制备了氧化石墨烯(GO),并通过扫描电镜(SEM)和原子力显微镜(AFM)对GO微观形貌进行了表征.详细研究了GO与硅磷低聚物(DMS-DOPO)在环氧树脂(EP)力学性能和阻燃性能中的协同作用.万能材料试验测试结果表明,GO和DMS-DOPO分别对拉伸强度和断裂伸长率提高效果明显,二者协同后,可使EP拉伸强度和断裂伸长率分别提高17.1%和42.2%.采用热重分析(TG)、极限氧指数(LOI)、垂直燃烧(UL-94)、锥型量热(CONE)和SEM对EP及其阻燃材料的热性能、燃烧性能以及炭层微观形貌进行了表征.EP/DMS-DOPO/GO在600℃残留量为EP的5.2倍,比EP/DMS-DOPO和EP/GO分别提高4.4%和208.6%.EP/DMS-DOPO/GO的LOI值大于30,并能通过UL-94 V-0级别,燃烧过程中可形成内部结构疏松多孔、外表面致密的膨胀炭层.DMS-DOPO和GO协同后使EP热释放速率峰值由1154 k W·m-2降低到710 k W·m-2,总烟释放量降低30%.     

含烯丙基六苯氧基环三磷腈的合成及其在阻燃丙烯酸酯树脂中的应用

以六氯环三磷腈（HCCP）、苯酚和2-烯丙基苯酚为原料,合成了新型含烯丙基的环磷腈阻燃单体（2-烯丙基苯氧基）五苯氧基环三磷腈（APPCP),用红外光谱、核磁氢谱、质谱和元素分析表征其组成和结构。 将APPCP与丙烯酸酯单体共聚制备了阻燃丙烯酸酯树脂,测试了共聚丙烯酸酯树脂的热稳定性和阻燃性,当APPCP用量为20%时,共聚丙烯酸酯树脂燃烧等级（UL-94）可达V-0级,极限氧指数（LOI）高达31.2%,在空气中600 ℃时残留质量提高至23.2%。     

碳纳米管改性环氧树脂的导热和阻燃性能

以双酚A二缩水甘油醚(DGEBA)环氧树脂(Epoxy Resin,EP)为基体、甲基六氢苯酐(MHHPA)为固化剂、以多壁碳纳米管(MWCNTs)为添加剂制备了环氧树脂/碳纳米管纳米复合材料。通过对微观结构、玻璃化转变温度(Tg)、热失重、热导率和锥形量热测试结果分析,研究了质量分数少于1.5%的MWCNTs对环氧树脂的导热和阻燃性能影响,结果表明,MWCNTs质量分数为1.5%时,复合材料发生团聚;纳米复合材料随着MWCNTs质量分数的增加Tg值先增加后降低;失重5%时,对应的温度先增加后降低,残炭量增加;样品的热导率呈现先升高后降低的趋势,当MWCNTs质量分数为1%时,复合材料的热导率最大;MWCNTs加入后环氧树脂的总释热量减少,释烟量增加,阻燃性得到一定程度的提高。     

A Bridge-Linked Phosphorus-Containing Flame Retardant for Endowing Vinyl Ester Resin with Low Fire Hazard

The high flammability of vinyl ester resin (VE) significantly limits its widespread application in the fields of electronics and aerospace. A new phosphorus-based flame retardant 6,6’-(1-phenylethane-1,2 diyl) bis (dibenzo[c,e][1,2]oxaphosphinine 6-oxide) (PBDOO), was synthesized using 9,10-dihydro-9-oxa-10-phosphaphenanthrene-10-oxide (DOPO) and acetophenone. The synthesized PBDOO was further incorporated with VE to form the VE/PBDOO composites, which displayed an improved flame retardancy with higher thermal stability. The structure of PBDOO was investigated using Fourier transformed infrared spectrometry (FTIR) and nuclear magnetic resonances (NMR). The thermal stability and flame retardancy of VE/PBDOO composites were investigated by thermogravimetric analysis (TGA), vertical burn test (UL-94), limiting oxygen index (LOI), and cone calorimetry. The impacts of PBDOO weight percentage (wt%) on the flame-retardant properties of the formed VE/PBDOO composites were also examined. When applying 15 wt% PBDOO, the formed VE composites can meet the UL-94 V-0 rating with a high LOI value of 31.5%. The peak heat release rate (PHRR) and the total heat release (THR) of VE loaded 15 wt% of PBDOO decreased by 76.71% and 40.63%, respectively, compared with that of untreated VE. In addition, the flame-retardant mechanism of PBDOO was proposed by analyzing pyrolysis behavior and residual carbon of VE/PBDOO composites. This work is expected to provide an efficient method to enhance the fire safety of VE.     

聚磷酸酯阻燃剂复配聚磷酸铵对环氧树脂阻燃性能的影响

合成了一种9,10-二氢-9-氧杂-10-磷杂菲-10-氧化物(DOPO)的衍生物——聚苯氧基磷酸-2-10-氢-9-氧杂-磷杂菲基对苯二酚酯(POPP), 以间苯二胺(m-PDA)为固化剂, 环氧树脂(EP)为基料, POPP为阻燃剂, 复配聚磷酸铵(APP), 制备了不同磷含量的阻燃环氧树脂. 利用极限氧指数(LOI)和垂直燃烧(UL94)实验表征了环氧树脂的阻燃性能; 以热重分析、 锥型量热和扫描电镜分析了阻燃环氧树脂的热性能和表面形态. 研究结果表明, 阻燃剂总加入量(质量分数)为5%时即可达到UL94 V-0级, 同时LOI值为27.7%; 当总加入量为15%, 即w_POPP=5%, w_APP=10 %时, 其LOI值可达到33.8%. 随着磷含量的增加, 阻燃环氧树脂的初始降解温度略有降低, 但高温下的残炭率明显增加. POPP/APP的加入在很大程度上降低了环氧树脂的热释放速率、 有效燃烧热、 烟释放量和有毒气体释放量. 阻燃环氧树脂在高温下形成比较稳定的致密膨胀炭层, 为底层的环氧树脂主体隔绝了分解产物及热量和氧气交换, 增强了高温下的热稳定性.     

密胺树脂/硼酸锌双层包覆微胶囊化红磷的制备及其在阻燃聚烯烃中的应用

描述了采用密胺树脂和硼酸锌连续双层包覆微胶囊化红磷(MRP)的最新制备方法。采用红外光谱、电子能谱和透射电镜等分析手段对其进行了表征，并证实红磷已被完全包覆。实验数据表明：经包覆的MRP的热稳定性获得了明显改善，吸水率和磷化氢的发生量均大大减少。MRP作为阻燃助剂应用于聚烯烃阻燃材料表现出了良好的阻燃效果。实时红外和热失重测量以及扫描电镜观察表明：其阻燃机制是红磷受热时与树脂反应促进了含磷膨胀炭层的形成，从而提高了材料的热稳定性，碳层起到了隔氧、隔热作用，而且主要在凝聚相中发挥其阻燃作用。     

Improving Thermal and Flame Retardant Properties of Epoxy Resin with Organic NiFe‐Layered Double Hydroxide‐Carbon Nanotubes Hybrids

To improve the dispersion of carbon nanotubes (CNTs) and flame retardancy of layered double hydroxide (LDH) in epoxy resin (EP), organic nickel‐iron layered double hydroxide (ONiFe‐LDH‐CNTs) hybrids were assembled through co‐precipitation. These hybrids were further used as reinforcing filler in EP. EP/ONiFe‐LDH‐CNTs nanocomposites containing 4 wt% of ONiFe‐LDH‐CNTs with different ratios of ONiFe‐LDH and CNTs were prepared by ultrasonic dispersion and program temperature curing. The structure and morphology of the obtained hybrids were characterized by different techniques. The dispersion of nanofillers in the EP matrix was observed by transmission electron microscopy (TEM). The results revealed a coexistence of exfoliated and intercalated ONiFe‐LDH‐ CNTs in polymer matrix. Strong combination of the above nanofillers with the EP matrix provided an efficient thermal and flame retardant improvement for the nanocomposites. It showed that EP/ONiFe‐LDH‐CNTs nanocomposites exhibited superior flame retardant and thermal properties compared with EP. Such improved thermal properties could be attributed to the better homogeneous dispersion, stronger interfacial interaction, excellent charring performance of ONiFe‐LDH and synergistic effect between ONiFe‐LDH and CNTs.     

Phosphorus Modified Cardanol: A Greener Route to Reduce VolaTile Organic Compounds and Impart Flame Retardant Properties to Alkyd Resin Coatings

Novel phosphorylated cardanol molecules based on phosphonate (PO₃CR) and phosphate (PO₄CR) functions were synthetized. Those molecules have two main actions which are described in this article: the reduction in volatile organic compounds (VOC) and the development of flame retardant (FR) properties conferred on alkyd resins used as coatings for wood specimen. Phosphorylated cardanol compounds have been successfully grafted by covalent bonds to alkyd resins thanks to an auto-oxidative reaction. The impact of the introduction of PO₃CR and PO₄CR on the film properties such as drying time and flexibility has been studied and the thermal and flame retardant properties through differential scanning calorimeter, thermogravimetric analysis and pyrolysis-combustion flow calorimeter. These studies underscored an increase in the thermal stability and FR properties of the alkyd resins. In the cone calorimeter test, the lowest pHRR was obtained with 3 wt% P of phosphate-cardanol and exhibited a value of 170 KW.m⁻², which represented a decrease of almost 46% compared to the PO_xCR-free alkyd resins. Moreover, a difference in the mode of action between phosphonate and phosphate compounds has been highlighted. The most effective coating which combined excellent FR properties and good coating properties has been obtained with 2 wt% P of phosphate-cardanol. Indeed, the film properties were closed to the PO_xCR-free alkyd resin and the pHRR decreased by 41% compared to the reference alkyd resin.     

High Loading Pt Core/Carbon Shell Derived from Platinum‐Aniline Complex for Direct Methanol Fuel Cell Application

A novel approach to high loaded Pt core/carbon shell catalyst synthesis from a Pt‐aniline complex was reported. The Pt‐aniline complex was successfully synthesized by irradiating an ultrasound to the hexachloro platinic acid and aniline monomer mixture. The highly viscous nature of aniline leads to reproducible hexagonal plate like Pt‐aniline complex crystals. The chemical composition of the Pt‐aniline complex was identified as [PtCl₂(C₆H₅NH₂)₂] with the help of NMR, XPS, HR ESI‐MS, and TGA analyses. Furthermore, the Pt‐aniline hexagonal plates were sintered at various temperatures like 400 °C, 500 °C, and 700 °C for an hour. This formed the highly dispersed carbon covered Pt nano particles with loading of 80.1 wt %, 81.3 wt %, and 83.4 wt % for HP‐4, HP‐5, and HP‐7, respectively. After supporting it on Vulcan XC‐72, Pt core/carbon shell pyrolyzed at a low temperature showed excellent performance in methanol oxidation reaction. In addition, Pt core/carbon shell prepared at a high temperature revealed excellent tolerance to methanol.     

Cobalt Phthalocyanine Immobilized on Graphene Oxide: An Efficient Visible‐Active Catalyst for the Photoreduction of Carbon Dioxide

New graphene oxide (GO)‐tethered–Co^II phthalocyanine complex [CoPc–GO] was synthesized by a stepwise procedure and demonstrated to be an efficient, cost‐effective and recyclable photocatalyst for the reduction of carbon dioxide to produce methanol as the main product. The developed GO‐immobilized CoPc was characterized by X‐ray diffraction (XRD), FTIR, XPS, Raman, diffusion reflection UV/Vis spectroscopy, inductively coupled plasma atomic emission spectroscopy (ICP‐AES), thermogravimetric analysis (TGA), Brunauer–Emmett–Teller (BET), scanning electron microscopy (SEM), and transmission electron microscopy (TEM). FTIR, XPS, Raman, UV/Vis and ICP‐AES along with elemental analysis data showed that Co^II–Pc complex was successfully grafted on GO. The prepared catalyst was used for the photocatalytic reduction of carbon dioxide by using water as a solvent and triethylamine as the sacrificial donor. Methanol was obtained as the major reaction product along with the formation of minor amount of CO (0.82 %). It was found that GO‐grafted CoPc exhibited higher photocatalytic activity than homogeneous CoPc, as well as GO, and showed good recoverability without significant leaching during the reaction. Quantitative determination of methanol was done by GC flame‐ionization detector (FID), and verification of product was done by NMR spectroscopy. The yield of methanol after 48 h of reaction by using GO–CoPc catalyst in the presence of sacrificial donor triethylamine was found to be 3781.8881 μmol g^?1 cat., and the conversion rate was found to be 78.7893 μmol g^?1cat. h^?1. After the photoreduction experiment, the catalyst was easily recovered by filtration and reused for the subsequent recycling experiment without significant change in the catalytic efficiency.     

Core Shell Nanostructure: Impregnated Activated Carbon as Adsorbent for Hydrogen Sulfide Adsorption

This study focuses on the synthesis, characterization, and evaluation of the performance of core shell nanostructure adsorbent for hydrogen sulfide (H₂S) capture. Commercial coconut shell activated carbon (CAC) and commercial mixed gas of 5000 ppm H₂S balanced N₂ were used. With different preparation techniques, the CAC was modified by core shell impregnation with zinc oxide (ZnO), titanium oxide (TiO₂), potassium hydroxide (KOH), and zinc acetate (ZnAC₂). The core structure was prepared with CAC impregnated by single chemical and double chemical labelled with ZnAC₂-CAC (single chemical), ZnAC₂/KOH-CAC, ZnAC₂/ZnO-CAC, and ZnAC₂/TiO₂-CAC. Then, the prepared core was layered either with KOH, TiO₂, NH₃, or TEOS for the shell. The synthesized adsorbents were characterized in physical and chemical characterization through scanning electron microscopy (SEM), thermal gravimetric analysis (TGA), and Brunauer-Emmett-Teller (BET) analyzers. Operation of the adsorber column takes place at ambient temperature, with absolute pressure at 1.5 bar. The H₂S gas was fed into the column at 5.5 L/min and the loaded adsorbents were 150 g. The performance of synthesized adsorbent was analyzed through the adsorbent’s capability in capturing H₂S gas. Based on the results, ZnAc₂/ZnO/CAC_WOS shows a better adsorption capacity with 1.17 mg H₂S/g and a 53% increment compared to raw CAC. However, the degradation of the adsorbents was higher compared to ZnAc₂/ZnO/CAC_OS and to ZnAc₂/ZnO/CAC_WS ZnAc₂/ZnO/CAC_OS. The presence of silica as a shell has potentially increased the adsorbent’s stability in several cycles of adsorption-desorption.     

Axial Modification of Cobalt Complexes on Heterogeneous Surface with Enhanced Electron Transfer for Carbon Dioxide Reduction

Efficient electron communication between molecular catalyst and support is critical for heterogeneous molecular electrocatalysis and yet it is often overlooked during the catalyst design. Taking CO₂ electro-reduction on tetraphenylporphyrin cobalt (PCo) immobilized onto graphene as an example, we demonstrate that adding a relay molecule improves the interfacial electron communication. While the directly immobilized PCo on graphene exhibits relatively poor electron communications, it is found that diphenyl sulfide serves as an axial ligand for PCo and it improves the redox activity of PCo on the graphene surface to facilitate the generation of [PCo]^.- active sites for CO₂ reduction. Thus, the turnover frequencies of the immobilized Co complexes are increased. Systematic structural analysis indicates that the benzene rings of diphenyl sulfide exhibit strong face-to-face stacking with graphene, which is proposed as an efficient medium to facilitate the interfacial electron communication.     

金属有机框架衍生的多孔碳修饰电极同时检测邻苯二酚和对苯二酚

本文运用金属有机框架(MOFs)作为模板,在惰性气体下热处理,合成金属有机框架衍生多孔碳材料(Metal Organic Frameworks Derived Porous Carbon,MDPC)。采用扫描电子显微镜(SEM)和X射线粉末衍射(XRD)分别对MDPC进行形貌和相纯度的表征。采用滴涂法将MDPC修饰在玻碳电极表面,运用循环伏安法(CV)、差分脉冲伏安法(DPV)、交流阻抗法(EIS)等电化学方法对该电极进行电化学表征,研究邻苯二酚(CC)和对苯二酚(HQ)在MDPC修饰电极上的电化学行为。结果表明,该修饰电极对CC和HQ这两种异构体表现出优异的氧化还原电活性和区分效果。在最佳实验条件下,CC和HQ的浓度在0.5~80μmol/L的范围内与氧化峰电流呈现良好的线性关系。CC和HQ的检测限分别为0.031μmol/L和0.11μmol/L。该方法电流响应大、灵敏度高、检测限低,具有实际应用前景。     

Palladium Nanoparticles Immobilized on Individual Calcium Carbonate Plates Derived from Mussel Shell Waste: An Ecofriendly Catalyst for the Copper‐Free Sonogashira Coupling Reaction

The conversion of waste into high‐value materials is considered an important sustainability strategy in modern chemical industries. A large volume of shell waste is generated globally from mussel cultivation. In this work, mussel shell waste (Perna viridis ) is transformed into individual calcium carbonate plates (ICCPs) and is applied as a support for a heterogeneous catalyst. Palladium nanoparticles (3–6 nm) are deposited with an even dispersion on the ICCP surface, as demonstrated by X‐ray diffraction and scanning electron microscopy. Using this system, Sonogashira cross‐coupling reactions between aryl iodides and terminal acetylenes were accomplished in high yields with the use of 1 % Pd/ICCP in the presence of potassium carbonate without the use of any copper metal or external ligand. The Pd/ICCP catalyst could also be reused up to three times and activity over 90 % was maintained with negligible Pd‐metal leaching. This work demonstrates that mussel shell waste can be used as an inexpensive and effective support for metal catalysts in coupling reactions, as demonstrated by the successful performance of the Pd‐catalyzed, copper‐free Sonogashira cross‐coupling process.     

源自水稻壳的高比表面纳米二氧化硅负载12-磷钨酸:一种高效纳米催化剂用于几种有机反应(英文)

Nano silica was prepared from rice husk with high surface area.X-ray diffraction(XRD) pattern showed that the amorphous form of silica was produced.Chemical composition of the nano silica was estimated by X-ray fluorescence spectroscopy and CHN analysis.The nano silica was used as a support for H3PW12O40.The nano silica and nano silica supported H3PW12O40 were characterized by inductively coupled plasma,XRD,transmission electron microscopy(TEM),N2 adsorption-desorption,and Fourier transform infrared spectroscopy.TEM images of nano silica as well as the supported catalyst displayed average size of 6 and 7 nm,respectively.The catalyst showed excellent activity in some important organic reactions including Biginelli,Hantzsch,Mannich,and Claisen-Schmidt reactions with good reusability.Catalytic activity of this nano catalyst is an improvement over the commercially available silica that is used to support H3PW12O40.     

Carbon Nanotubes Decorated with CoP Nanocrystals: A Highly Active Non‐Noble‐Metal Nanohybrid Electrocatalyst for Hydrogen Evolution

The development of effective and inexpensive hydrogen evolution reaction (HER) electrocatalysts for future renewable energy systems is highly desired. The strongly acidic conditions in proton exchange membranes create a need for acid‐stable HER catalysts. A nanohybrid that consists of carbon nanotubes decorated with CoP nanocrystals (CoP/CNT) was prepared by the low‐temperature phosphidation of a Co₃O₄/CNT precursor. As a novel non‐noble‐metal HER catalyst operating in acidic electrolytes, the nanohybrid exhibits an onset overpotential of as low as 40 mV, a Tafel slope of 54 mV dec^?1, an exchange current density of 0.13 mA cm^?2, and a Faradaic efficiency of nearly 100 %. This catalyst maintains its catalytic activity for at least 18 hours and only requires overpotentials of 70 and 122 mV to attain current densities of 2 and 10 mA cm^?2, respectively.     

Utilization of N,N‐Dialkylcarbamic Acid Derived from Secondary Amines and Supercritical Carbon Dioxide: Stereoselective Synthesis of Z Alkenyl Carbamates with a CO2‐Soluble Ruthenium–P(OC2H5)3 Catalyst

Reversible transformation of diethylamine ( 1 ) and supercritical carbon dioxide (scCO₂) into N,N‐diethylcarbamic acid ( 2 ) was confirmed by direct acquisition of ¹H and ¹³C{¹H} NMR spectra. The equilibrium between 1 +CO₂ and 2 is strongly influenced by conditions of the supercritical state. Low temperature favors formation of carbamic acid, whereas high temperature causes decarboxylation. On the basis of the spectroscopic results of carbamic acid formation under scCO₂ conditions, the ruthenium‐catalyzed formation of alkenyl carbamates from terminal alkynes, 1 , and carbon dioxide was investigated to demonstrate the useful transformation of elusive carbamic acids. Selectivity toward the CO₂‐fixation products over enynes obtained by dimerization of the alkyne substrates was improved by the use of scCO₂ as a reaction medium. In particular, a CO₂‐soluble ruthenium complex, trans‐[RuCl₂{P(OC₂H₅)₃}₄], was found to be effective in affording Z alkenyl carbamates with high stereoselectivity.