吸附相反应技术制备MnOx/CeO2/SiO2催化剂及其低温选择性催化还原Nox

采用吸附相反应技术制备得到了MnO_x/CeO₂/SiO₂催化剂,通过X 射线衍射（XRD）、透射电子显微镜（TEM）、高分辨透射电子显微镜（HRTEM）、紫外激光拉曼（Raman）等手段对催化剂进行了表征. HRTEM分析表明活性组分MnO_x与CeO₂都均匀分布在载体SiO₂表面;XRD分析表明Mn₃O₄特征峰随着CeO₂含量的增加逐渐减小至完全消失,CeO₂的加入降低了MnO_x的结晶程度,增加了MnO_x的分散性;Raman光谱表明催化剂表面的Mn离子能够进入CeO₂晶格,激发出空穴氧,随着CeO₂负载量的增加,催化剂氧空穴浓度先升高后降低.以NH₃为还原剂,考评催化剂的NO_x低温选择性催化还原（SCR）性能,催化剂催化活性随CeO₂负载量增加先升高后降低,与催化剂氧空穴浓度变化规律一致,说明催化剂活性受氧空穴浓度影响,氧空穴浓度升高,催化剂催化活性升高.     

制备方法对CuO/CeO_2-ZrO_2催化CO低温氧化活性的影响

采用微波加热分解法(一步法)和微波加热处理共沉淀+浸渍法(两步法)制备了CuO/CeO2-ZrO2催化剂,并对其进行了X射线衍射、低温氮气吸附/脱附和程序升温还原等表征,采用色谱流动法考察了催化剂的催化CO低温氧化性能.结果表明,一步法比两步法更有利于使催化剂表面CuO高度分散,CuO与CeO2-ZrO2间的相互作用更强,CuO更容易被还原,从而具有更高的催化CO氧化活性.与CeO2-ZrO2有相互作用的高分散和小颗粒CuO有利于催化剂活性的提高,与CeO2-ZrO2无相互作用的大颗粒CuO对催化剂的活性有抑制作用.     

A comparative study on the dispersion behaviors and surface acid properties of molybdena on CeO2 and ZrO2 (Tet)

Dispersion of molybdena on CeO₂, ZrO₂ (Tet), and a mixture of CeO₂ and ZrO₂ (Tet), was investigated by using laser Raman spectroscopy (LRS), Fourier transform infrared spectroscopy (FT-IR), X-ray diffraction (XRD) and temperature programmed reduction (TPR). The results indicate that molybdena is dispersed on both individual oxide support and mixed oxide support at the adopted molybdena loadings (0.2 and 0.8 mmol Mo⁶⁺/100 m²) and the structure of the supported molybdena species is intimate association with its loading amount. Two molybdena species are identified by Raman results, i.e. isolated MoO²⁻₄ species at 0.2 mmol Mo⁶⁺/100 m² and polymolybdate species at 0.8 mmol Mo⁶⁺/100 m². IR spectra of ammonia adsorption prove that isolated MoO²⁻₄ species are Lewis acid sites on the Mo/Ce and/or Zr samples, and the polymolybdate species are Brönsted acid sites on the Mo/Ce and/or Zr samples. Moreover, a combination of the Raman, IR and TPR results confirms that at 0.2 mmol Mo⁶⁺/100 m² Ce + Zr, molybdena is preferentially dispersed on the surface of CeO₂ when a mixed oxide support (CeO₂ and ZrO₂) is present, which was explained in term of the difference of the surface basicity between CeO₂ and ZrO₂ (Tet). Surface structures of the oxide supports were also taken into consideration.     

Dispersion state of CuO on CeO2

XRD and XPS are used to study the dispersion state of CuO on ceria surface. The dispersion capacity values of CuO measured by the two methods are consistent, which are of 1.20 mmol CuO/100 m² CeO₂. In addition, the results reveal that highly dispersed Cu²⁺ ions are formed at low CuO loadings and that increasing the CuO content to a value higher than its dispersion capacity produces crystalline CuO after the surface vacant sites on CeO₂ are filled. The atomic composition of the outermost layer of the CuO/CeO₂ samples has been probed by using static secondary ion mass spectroscopy (SSIMS), and the ratim of Cu/Ce are found to be 0.93 and 0.46 for the 1.22 and 0.61 mmol CuO/CeO₂ samples respectively. Temperature-programmed reduction (TPR) profile with two reduction peaks at 156 and 165°C suggests that the reduction of highly dispersed Cu²⁺ ions consists of two steps and is easier than that of CuO crystallites, in which the TPR profile has only one reduction peak at about 249°C. The above experimental results are in good agreement with the prediction of the incorporation model. Project supported by the National Natural Science Foundation of China.     

非晶态ZrO2镶嵌的超细CeO2催化HCl氧化

采用不同方法制备了铈锆复合氧化物催化剂用于催化HCl氧化反应。自发沉积策略制备的CeO₂@ZrO₂催化剂中,超细CeO₂纳米粒子均匀的镶嵌于非晶态ZrO₂中。CeO₂粒子显著的“尺寸效应”使得该催化剂具有更高的Ce³⁺和氧空位浓度,而较高的Ce³⁺和氧空位浓度使得催化剂具有优异的低温氧化还原性能和储释氧能力。催化性能测试表明,CeO₂@ZrO₂催化剂展现出最好的催化活性（1.90 g_Cl2·g_cat^-1·h^-1）,同时CeO₂粒子周围非晶态的ZrO₂阻碍CeO₂的高温烧结,提高了该催化剂的稳定性。     

非晶态ZrO_2镶嵌的超细CeO_2催化HCl氧化

采用不同方法制备了铈锆复合氧化物催化剂用于催化HCl氧化反应。自发沉积策略制备的CeO_2@ZrO_2催化剂中,超细CeO_2纳米粒子均匀的镶嵌于非晶态ZrO_2中。CeO_2粒子显著的"尺寸效应"使得该催化剂具有更高的Ce~(3+)和氧空位浓度,而较高的Ce~(3+)和氧空位浓度使得催化剂具有优异的低温氧化还原性能和储释氧能力。催化性能测试表明,CeO_2@ZrO_2催化剂展现出最好的催化活性(1.90 gCl2·gcat~(-1)·h~(-1)),同时CeO_2粒子周围非晶态的ZrO_2阻碍CeO_2的高温烧结,提高了该催化剂的稳定性。     

Au/CeO2中强金属-载体相互作用的形貌效应

以Au/CeO₂为研究对象,通过构建不同形貌的CeO₂载体来研究强金属-载体相互作用（SMSI）的形貌效应。分别以纳米立方块和纳米棒作为载体,通过高分辨（扫描）透射电子显微、光电子能谱、氢程序升温还原等一系列表征方法揭示了CeO₂纳米立方块表面更易发生质量传输并形成CeO_2-x包覆层。此包覆层大幅抑制了催化剂对小分子气体的吸附能力,并减少了催化活性位点的暴露,对探针反应（丁二烯选择性催化加氢）的催化活性影响显著。以上研究结果表明CeO₂纳米立方块比CeO₂纳米棒更易构建SMSI体系。     

CeO_2/ZnO复合纳米管的制备及其光催化性能的研究

用纳米CeO2掺入ZnO纳米管制备了CeO2/ZnO复合纳米管,考察了复合纳米管的光学及其光催化性能,并运用X射线衍射、透射电镜、比表面积测定和紫外-可见漫反射光谱等技术对样品进行了表征.结果表明,与ZnO纳米管相比,CeO2/ZnO复合纳米管的比表面积虽有所降低,但光催化活性有所提高,随着复合纳米CeO2量的增加,催化剂的光催化活性相应降低,太阳光下CeO2/ZnO复合纳米管对甲基橙溶液也有较高的催化活性.     

Catalytic methanol decomposition to carbon monoxide and hydrogen over Pd/CeO2-ZrO2-La2O3 with different Ce/Zr molar ratios

The catalytic behaviors of Pd (1.4 wt%) catalysts supported on CeO₂-ZrO₂-La₂O₃ mixed oxides with different Ce/Zr molar ratios were investigated for methanol decomposition. Nitrogen adsorption-desorption (BET), X-ray photoelectron spectroscopy (XPS), H₂ temperature-programmed reduction (H₂-TPR), X-ray diffraction (XRD) and Pd dispersion analysis were used for their characterization. Pd/Ce_0.76Zr_0.18 La_0.06O_1.97 catalyst showed the highest BET surface area, best Pd dispersion capability and strongest metal-support interaction. Moreover, XPS showed that there was lattice defect oxygen or mobile oxygen. According to the result of O 1s measurements the lattice defect oxygen or mobile oxygen helped to maintain Pd in a partly oxidized state and increased the activity for methanol decomposition. The Pd/Ce_0.76Zr_0.18La_0.06O_1.97 catalyst exhibited the best activity. A 100% conversion of methanol was achieved at around 260 °C, which was about 20-40 °C lower than other catalysts     

Insight into the Morphology-Dependent Catalytic Performance of CuO/CeO2 Produced by Tannic Acid for Efficient Hydrogenation of 4-Nitrophenol

The construction of a heterogeneous nanocatalyst with outstanding catalytic performance via an environmentally benign and cost-effective synthetic category has long been one of the challenges in nanotechnology. Herein, we synthesized highly efficient and low-cost mesoporous morphology-dependent CuO/CeO₂-Rods and CuO/CeO₂-Cubes catalysts by employing a green and multifunctional polyphenolic compound (tannic acid) as the stabilizer and chelating agent for 4-nitrophenol (4-NP) reduction reaction. The CuO/CeO₂-Rods exhibited excellent performance, of which the activity was 3.2 times higher than that of CuO/CeO₂-Cubes. This can be connected with the higher density of oxygen vacancy on CeO₂-Rods (110) than CeO₂-Cubes (100), the oxygen vacancy favors anchoring CuO species on the CeO₂ support, which promotes the strong interaction between finely dispersed CuO and CeO₂-Rods at the interfacial positions and facilitates the electron transfer from BH₄⁻ to 4-NP. The synergistic catalytic mechanism illustrated that 4-NP molecules preferentially adsorbed on the CeO₂, while H₂ from BH₄⁻ dissociated over CuO to form highly active H* species, contributing to achieving efficient hydrogenation of 4-NP. This study is expected to shed light on designing and synthesizing cost-effective and high-performance nanocatalysts through a greener synthetic method for the areas of catalysis, nanomaterial science and engineering, and chemical synthesis.     

Reaction of NO at low temperature by ACF loading urea and rare-earth element oxides (La2O3, CeO2)

Loaded catalysts of 10–50% (w/w) urea loaded on activated carbon fibers (ACF), referred to as urea/ACF, and 10%urea–5–15% (w/w) La₂O₃/ACF and CeO₂/ACF were prepared by an impregnation method and used for removal of NO at low temperature (30–120°C). The experimental results showed that the catalytic activity of urea/ACF could be greatly improved by loaded rare-earth element oxides. Furthermore, 10%urea–5%La₂O₃/ACF and 10%urea–10%CeO₂/ACF could maintain high and stable catalytic activity at 100°C.     

Opposite Face Sensitivity of CeO2 in Hydrogenation and Oxidation Catalysis

The determination of structure–performance relationships of ceria in heterogeneous reactions is enabled by the control of the crystal shape and morphology. Whereas the (100) surface, predominantly exposed in nanocubes, is optimal for CO oxidation, the (111) surface, prevalent in conventional polyhedral CeO₂ particles, dominates in C₂H₂ hydrogenation. This result is attributed to the different oxygen vacancy chemistry on these facets. In contrast to oxidations, hydrogenations on CeO₂ are favored over low‐vacancy surfaces owing to the key role of oxygen on the stabilization of reactive intermediates. The catalytic behavior after ageing at high temperature confirms the inverse face sensitivity of the two reaction families.     

合成方法对Rh/CeO2-ZrO2-La2O3催化剂的结构、表面性能及DeNOx活性的影响

用沉积沉淀法合成两种不同系列的CeO2-ZrO2-La2O3混合氧化物(ZrO2和La2O3沉积CeO2粒子(标记为A-x)以及CeO2和La2O3沉积ZrO2粒子(标记为B-x)),并用作Rh催化剂的载体。XRD、拉曼、TPR、XPS和O2脉冲等表征结果显示出不同的沉积顺序将导致不同的结构和氧化还原性能,且B-x具有更高的氧迁移性、储氧能力和表面Ce浓度。当其负载Rh后,Rh/B-x催化剂具有更高的NO和CO转化率及N2选择性,且Ce的最佳含量为50at%。这可能归因于Rh负载于富铈表面形成更多有利于NO分解的表面Ce3+活性位。     

Characterization of an all Sol-Gel Electrochromic Device WO3/Ormolyte/CeO2-TiO2

Electrochemical lithium intercalation in thin films of CeO₂-TiO₂ and WO₃, prepared by the sol-gel technique was investigated with cyclic voltammetry and spectroelectrochemical techniques in propylene carbonate solutions. A solid state system having the configuration WO₃/Ormolyte/CeO₂-TiO₂ has been assembled. The solid electrolyte, an organically modified electrolyte (ormolyte), was prepared with different [O]/[Li] ratios. The transmittance variation of this system during a potentiostatic step from –0.7 V to 0.8 V was about 35% at 550 nm.     

Thermal behaviour of CO2 laser-irradiated CeO2 doped with Yb2O3

Results concerning the thermal behaviour of Yb₂O₃-doped CeO₂ samples irradiated with CO₂ laser beams in continuous wave are presented.

---

Zusammenfassung Es werden Ergebnisse einer Untersuchung des thermischen Verhaltens von CeO₂-Proben dargelegt, die mit CO₂-Laser bestraht wurden.

     

Selective catalytic reduction of NO with CO on Pt/W–Ce–Zr catalysts

Various Pt catalysts (Pt/ZrO₂, Pt/CeO₂, Pt/CeZrO, Pt/WO₃/ZrO₂ and Pt/WO₃/CeZrO) were prepared and characterized, and their catalytic reduction reactions of NO by CO, with or without the presence of excess oxygen, were investigated. The results of temperature-programmed experiments showed that CO could be easily oxidized over Pt/CeO₂ and Pt/CeZrO while the introduction of WO₃ into the catalyst (Pt/WO₃/CeZrO) inhibited the reduction of catalyst surface; NO could not dissociate over those catalysts in oxidized state but after CO reduction at a low temperature, NO dissociation took place only over Pt/CeO₂ and Pt/CeZrO catalysts. For NO + CO reaction, those easily reduced catalysts Pt/CeO₂ and Pt/CeZrO exhibited better catalytic performances, and NO could be rapidly converted below 350 °C. For the reaction with the presence of excess O₂, the NO conversions were significantly inhibited, but better NO conversions were obtained over the tungstate-contained catalysts when compared with Pt/CeO₂ and Pt/CeZrO. The higher activities of Pt/W–Ce–Zr catalysts were attributed to their high acidities.     

A Facile Approach to Well-Dispersible CeO2 Nanoparticles

18 nm CeO₂ with surface being functionalized by nitrate groups were prepared to yield a stable suspension in acidic aqueous solution. Different from the bare ones, these suspensions precipitated rapidly when the solution became basic. Further tuning the solution back to acidic led to a stable suspension again. This phenomenon was explained in terms of the electrostatic repulsion of electrical double layers of intensive surface bound nitrate groups and acidic medium.     

Preparation and characterization of mesoporous TiO2-CeO2 nanopowders respond to visible wavelength

Mesoporous TiO₂-CeO₂ nanopowders responding to visible wavelength were synthesized by using a surfactant assisted sol-gel technique. They were obtained using metal alkoxide precursors modified with acetylacetone (ACA) and laurylamine hydrochloride (LAHC) as surfactant. The samples were characterized by XRD, nitrogen adsorption isotherm, SEM, TEM, and selected area electron diffraction (SAED), respectively. The 95 mol% TiO₂-5 mol% CeO₂ system yielded single anatase phase, however, further addition of the CeO₂ formed cubic CeO₂ structure while anatase TiO₂ decreased. Additions of 5 and 10 mol% CeO₂ increased the surface area, but those of 25, 50, and 75 mol% CeO₂ did not affect it very much. By using this mixed metal oxides system, TiO₂ can be modified to respond to the visible wavelength. The mixed metal oxides had catalytic activity (evaluating the formation rate of I₃⁻) about 2-3 times higher than pure CeO₂, while nanosize anatase type TiO₂ materials had no catalytic activity under visible light. The catalytic activity was almost proportional to the specific surface area. The formation rate of I₃⁻ was much improved by changing the calcination temperature and calcination period. Highest catalytic activity in this study was obtained for the 50 mol% TiO₂-50 mol% CeO₂ nanopowders calcined at 250 °C for 24 h.     

Batch and Flow Synthesis of CeO2 Nanomaterials Using Solid-State Microwave Generators

Microwave-assisted synthesis in combination with flow synthesis offers an interesting approach to develop faster and more sustainable procedures for the preparation of homogeneous nanomaterials. Recently, solid-state generators of microwaves appeared as a tool with improved control over power and frequency. Cerium oxide, despite its excellent catalytic activity, has not been prepared before using solid-state generators or microwave-assisted flow chemistry. We report a procedure for the preparation of nanoparticulated CeO₂ (around 4 nm) under 2.45 GHz microwaves in only 30 s. The materials are further calcined at 800 °C to increase particle size, with a better defined particle size and crystallinity. The procedure was tested in batch at pH 11 and 12 and diverse potencies, and the products were characterized by TEM, XRD, DLS, and N₂ adsorption–desorption isotherms. The materials were similar at the diverse pH values and potencies. XRD confirms the crystallinity of the CeO₂ material with a fluorite-like structure. They are composed of particles around 40 nm that aggregate as structures of around 100 nm. The procedure was successfully adapted to flow synthesis, obtaining materials with structure and properties equivalent to batch synthesis. The batch and flow materials offer peroxidase properties, opening the door for their use as ROS scavengers.     

CeO2-ZrO2-La2O3-Al2O3 composite oxide and its supported palladium catalyst for the treatment of exhaust of natural gas engined vehicles

Composite supports CeO2-ZrO2-Al2O3 (CZA) and CeO2-ZrO2-Al2O3-La2O3 (CZALa) were prepared by co-precipitation method. Palladium catalysts were prepared by impregnation and their purification ability for CH4, CO and NOx in the mixture gas simulated the exhaust from natural gas vehicles (NGVs) operated under stoichiometric condition was investigated. The effect of La2O3 on the physicochemical properties of supports and catalysts was characterized by various techniques. The characterizations with X-ray diffraction (XRD) and Raman spectroscopy revealed that the doping of La2O3 restrained effectively the sintering of crystallite particles, maintained the crystallite particles in nanoscale and stabilized the crystal phase after calcination at 1000 ℃. The results of N2-adsorption, H2-temperature-programmed reduction (H2-TPR) and oxygen storage capacity (OSC) measurements indicated that La2O3 improved the textural properties, reducibility and OSC of composite supports. Catalytic activity testing results showed that the catalysts exhibit excellent activities for the simultaneous removal of methane, CO and NOx in the simulated exhaust gas. The catalysts supported on CZALa showed remarkable thermal stability and catalytic activity for the three pollutants, especially for NOx. The prepared palladium catalysts have high ability to remove NOx, CH4 and CO, and they can be used as excellent catalysts for the purification of exhaust from NGVs operated under stoichiometric condition. They also have significant potential in industrial application because of their high performance and low cost.