Determination of As(III) and total inorganic arsenic by flow injection hydride generation atomic absorption spectrometry

A simple procedure was developed for the direct determination of As(III) and As(V) in water samples by flow injection hydride generation atomic absorption spectrometry (FI–HG–AAS), without pre-reduction of As(V). The flow injection system was operated in the merging zones configuration, where sample and NaBH₄ are simultaneously injected into two carrier streams, HCl and H₂O, respectively. Sample and reagent injected volumes were of 250 μl and flow rate of 3.6 ml min⁻¹ for hydrochloric acid and de-ionised water. The NaBH₄ concentration was maintained at 0.1% (w/v), it would be possible to perform arsine selective generation from As(III) and on-line arsine generation with 3.0% (w/v) NaBH₄ to obtain total arsenic concentration. As(V) was calculated as the difference between total As and As(III). Both procedures were tolerant to potential interference. So, interference such as Fe(III), Cu(II), Ni(II), Sb(III), Sn(II) and Se(IV) could, at an As(III) level of 0.1 mg l⁻¹, be tolerated at a weight excess of 5000, 5000, 500, 100, 10 and 5 times, respectively. With the proposed procedure, detection limits of 0.3 ng ml⁻¹ for As(III) and 0.5 ng ml⁻¹ for As(V) were achieved. The relative standard deviations were of 2.3% for 0.1 mg l⁻¹ As(III) and 2.0% for 0.1 mg l⁻¹ As(V). A sampling rate of about 120 determinations per hour was achieved, requiring 30 ml of NaBH₄ and waste generation in order of 450 ml. The method was shown to be satisfactory for determination of traces arsenic in water samples. The assay of a certified drinking water sample was 81.7±1.7 μg l⁻¹ (certified value 80.0±0.5 μg l⁻¹).     

A simple and sensitive assay of nucleic acids based on the enhanced resonance light scattering of zwitterionics

A new assay of nucleic acids at nanogram level was established based on the enhanced resonance light scattering (RLS) signals of two zwitterionics cocamidopropyl hydroxysultaine (HSB) and lauryl betaine (BS-12). Under optimum conditions, the weak RLS signal of HSB is enhanced by nucleic acids, and the enhanced RLS intensity is proportional to the concentration of nucleic acids in the range of 0.02–7.3 mg l⁻¹ for calf thymus DNA and 0.01–8.6 mg l⁻¹ for fish sperm DNA. The detection limits were 1.5 ng ml⁻¹ for calf thymus DNA and 1.9 ng ml⁻¹ for fish sperm DNA. Plasmid DNA extracted from K-12-HB101 colt was determined with satisfactory results.     

A rapid and sensitive immunonanogold resonance scattering spectral probe for complement 3

Gold nanoparticles in size of about 10 nm was used to label goat anti-human complement 3 (anti-C3) to obtain a sensitive and selective immunoresonance scattering spectral probe for C3. It was based on the immune reaction between labeled anti-C3 and C3 in the pH 5.6 Na₂HPO₄–citric acid buffer solutions and in presence of polyethylene glycol (PEG). The resonance scattering (RS) intensity at 560 nm enhanced greatly with C3. Well linear relationships between the enhanced RS intensity (I_RS) and the C3 concentration in the range of 8.33–200 ng ml⁻¹ were obtained, with a detection limit of 2.8 ng ml⁻¹ and the limit of quantification 8.51 ng ml⁻¹ for C3. The convenient and selective and sensitive assay was applied to quantification of C3 in human sera, with satisfactory results.     

Application of a new resin functionalised with 6-mercaptopurine for mercury and silver determination in environmental samples by atomic absorption spectrometry

Polystyrene–divinylbenzene (8%) has been functionalised by coupling it through an ---N=N--- group with 6-mercaptopurine. The resulting chelating resin has been characterised by using elemental analysis, thermogravimetric analysis and infrared spectra. The resin is highly selective for Hg(II) and Ag(I) and has been used for preconcentrating Hg(II) and Ag(I) prior to their determination by atomic absorption spectrometry. The maximum sorption capacity for Hg(II) and Ag(I) was found to be 1.74 and 0.52 mmol g⁻¹, respectively, over the pH range 5.5–6.0. The calibration range for Hg(II) was linear up to 10 ng ml⁻¹ with a 3σ detection limit of 0.02 ng ml⁻¹; the calibration range for Ag(I) was linear up to 5 μg ml⁻¹ with a detection limit of 29 ng ml⁻¹. The recoveries of the metals were found to be 99.7±3.8 and 101.3±4.1% at the 95% confidence level for both Hg(II) and Ag(I). In column operation, it has been observed that Hg(II) and Ag(I) in trace quantities can be selectively separated from geological, medicinal and environmental samples.     

Flow injection determination of nitrite by fluorescence quenching

A simple, sensitive and selective fluorimetric method for the determination of nitrite ion in waters using a merging zones flow injection system is described. The fluorimetric determination is based on the measurement of the quenching effect produced by nitrite on proflavine (3,6-diaminoacridine) fluorescence (λ_ex/λ_em=290/519 nm).

The optimum experimental conditions were investigated by merging 0.5 ml of the sample and 0.5 ml of a solution of 5 mg l⁻¹ of proflavine (in 0.1 M HCl) in a flow injection system, on-line connected to a flow-cell placed in the conventional sample compartment of a spectrofluorimeter. The selected carrier solution and final flow rate were 0.1 M HCl and 0.5 ml min⁻¹, respectively. A reaction coil of 2 ml was used. As a result of the simplicity of this system, a sample throughput of about 50 samples h⁻¹ can be achieved with the proposed methodology.

The detection limit was 1.1 ng ml⁻¹ (3σ criterion) of nitrite. The repeatability for five sample injections containing 100 ng ml⁻¹ of nitrite was ±0.3% and the observed linear range extended up to 400 ng ml⁻¹. Also, the effect of interferences from various metals and anions commonly present in waters was also studied.

The method was successfully applied to the determination of low levels of nitrite in different water samples (river, fountain, tap and commercial drinking waters).     

Spectral studies on the interaction of Amido black 10B with DNA in the presence of cetyltrimethylammonium bromide

The interaction of Amido black 10B (AB) with DNA in basic medium was studied in the presence of cetyltrimethylammonium bromide (CTMAB) based on the measurements of resonance light scattering (RLS), UV–vis, CD spectra, and RLS imaging. The interaction has been proved to give a ternary complex of CTMAB–DNA–AB in Britton–Robinson buffer of pH 11.55, which exhibits strong negative Cotton effect at 233.3 nm and 642.8 nm, and strong RLS signals characterized at 469 nm. Experiments showed that the enhanced RLS intensities (ΔI_RLS) against the mixture of AB and CTMAB are proportional to the concentration of fish sperm DNA (fsDNA) and calf thymus DNA (ctDNA), respectively over the range of 0.03–1.0 and 0.05–1.5 μg ml⁻¹, with the limits of determination (3σ) of 7.3 ng ml⁻¹ for fsDNA and 7.0 ng ml⁻¹ for ctDNA.     

Resonance Rayleigh scattering, second-order scattering and frequency doubling scattering methods for the indirect determination of penicillin antibiotics based on the formation of Fe3[Fe(CN)6]2 nanoparticles

Under the HCl solution and heating condition, penicillin antibiotics such as amoxicillin (AMO), ampicillin (AMP), sodium cloxacillin (CLO), sodium carbenicillin (CAR) and sodium benzylpenicillin (BEN) could react with Fe(III) to produce Fe(II) which further reacted with Fe(CN)₆³⁻ to form a Fe₃[Fe(CN)₆]₂ complex. By virtue of hydrophobic force and Van der Waals force, the complex aggregated to form Fe₃[Fe(CN)₆]₂ nanoparticles with an average diameter of 45 nm. This resulted in a significant enhancement of resonance Rayleigh scattering (RRS) and non-linear scattering such as second-order scattering (SOS) and frequency doubling scattering (FDS). The increments of scattering intensity (ΔI) were directly proportional to the concentrations of the antibiotics in a certain range. The detection limits for the five penicillin antibiotics were 2.9–6.1 ng ml⁻¹ for RRS method, 4.0–6.8 ng ml⁻¹ for SOS method and 7.4–16.2 ng ml⁻¹ for FDS method, respectively. Among them, the RRS method exhibited the highest sensitivity and the AMO system was more sensitive than other antibiotics systems. Based on the above researches, a new highly sensitive and simple method for the indirect determination of penicillin antibiotics has been developed. It can be applied to the determination of penicillin antibiotics in capsule, tablet, human serum and urine samples. In this work, the spectral characteristics of absorption, RRS, SOS and FDS spectra, the optimum conditions of the reaction and the influencing factors were investigated. In addition, the reaction mechanism was discussed.     

Electrochemiluminescence sensor using tris(2,2′-bipyridyl)ruthenium(II) immobilized in Eastman-AQ55D–silica composite thin-films

An electrochemiluminescence (ECL) sensor with good long-term stability and fast response time has been developed. The sensor was based on the immobilization of tris(2,2′-bipyridyl)ruthenium(II) (Ru(bpy)₃²⁺) into the Eastman-AQ55D–silica composite thin films on a glassy carbon electrode. The ECL and electrochemistry of Ru(bpy)₃²⁺ immobilized in the composite thin films have been investigated, and the modified electrode was used for the ECL detection of oxalate, tripropylamine (TPA) and chlorpromazine (CPZ) in a flow injection analysis system and showed high sensitivity. Because of the strong electrostatic interaction and low hydrophobicity of Eastman-AQ55D, the sensor showed no loss of response over 2 months of dry storage. In use, the electrode showed only a 5% decrease in response over 100 potential cycles. The detection limit was 1 μmol l⁻¹ for oxalate and 0.1 μmol l⁻¹ for both TPA and CPZ (S/N=3), respectively. The linear range extended from 50 μmol l⁻¹ to 5 mmol l⁻¹ for oxalate, from 20 μmol l⁻¹ to 1 mmol l⁻¹ for TPA, and from 1 μmol l⁻¹ to 200 μmol l⁻¹ for CPZ.     

Efficiency and mechanism of new poly(acryl-phenylamidrazone phenylhydrazide) chelating fiber for adsorbing trace Ga, In, Bi, V and Ti from solution

A new po1y(acrylphenylamidrazone phenylhydrazide) chelating fiber is synthesized from polyacrylonitrile fiber and used for preconcentration and separation of trace Ga(III), In(III), Bi(III), V(V) and Ti(IV) from solution (5–50 ng ml⁻¹ Ti(IV) or V(V) and 50–500 ng ml⁻¹ Ga(III), In (III) or Bi(III) in 1000–100 ml of solution can be enriched quantitatively by 0.15 g of fiber at a 4 ml min⁻¹ flow rate in the pH range 5–7 with recoveries >95%). These ions can be desorbed quantitatively with 20 ml of 4 M hydrochloric acid at 2 ml min⁻¹ from the fiber column. When the fiber which had been treated with concentrated hydrochloric acid and washed with distilled water until neutral was reused eight times, the recoveries of the above ions by enrichment were still >95%. Two-hundred-fold to 10 000-fold excesses of Cu(II), Zn(II), Ca(II), Mn(II), Cr(III), Fe(III), Ba(II) and Al(III) caused little interference in the determination of these ions by inductively coupled plasma-atomic emission spectrometers (ICP-AES). The relative standard deviations for enrichment and determination of 50 ng ml⁻¹ Ga, In or Bi and 10 ng ml⁻¹ V or Ti are in the range 1.2–2.7%. The contents of these ions in real solution samples determined by this method were in agreement with the certified values of the samples with average errors <3.7%.     

Speciation of inorganic arsenic by electrochemical hydride generation atomic absorption spectrometry

A simple procedure was developed for the speciation of inorganic arsenic by electrochemical hydride generation atomic absorption spectrometry (EcHG–AAS), without pre-reduction of As(V). Glassy carbon was selected as cathode material in the flow cell. An optimum catholyte concentration for simultaneous generation of arsine from As(III) and As(V) was 0.06 mol l⁻¹ H₂SO₄. Under the optimized conditions, adequate sensitivity and difference in ratio of slopes of the calibration curves for As(III) and As(V) can be achieved at the electrolytic currents of 0.6 and 1 A. The speciation of inorganic arsenic can be performed by controlling the electrolytic currents, and the concentration of As(III) and As(V) in the sample can be calculated according to the equations of absorbance additivity obtained at two selected electrolytic currents. The calibration curves were linear up to 50 ng ml⁻¹ for both As(III) and As(V) at 0.6 and 1 A. The detection limits of the method were 0.2 and 0.5 ng ml⁻¹ for As(III) and As(V) at 0.6 A, respectively. The relative standard deviations were of 2.1% for 20 ng ml⁻¹ As(III) and 2.5% for 20 ng ml⁻¹ As(V). The method was validated by the analysis of human hair certified reference material and successfully applied to speciation of soluble inorganic arsenic in Chinese medicine.     

Development of an enzyme-linked immunosorbent assay for pentachlorophenol

Pentachlorophenol (PCP) is a hazardous pollutant with toxicity and potential carcinogenic properties being a serious threat to the environment. In this work, the development of an immunoassay for PCP is presented. A hapten was synthesised and conjugated to protein for rabbit immunisation. Three polyclonal antibodies were obtained and the best results were achieved in the antibody-coated format using antiserum R3. Calibration range was 0.3–30.5 ng ml⁻¹, with an average I₅₀ value of 2.9 ng ml⁻¹ and a detection limit of 0.1 ng ml⁻¹. The specificity of the assay was tested against PCP structurally related compounds. The method is highly specific for PCP and shows low cross-reactivity (CR) for chlorine-containing phenols, nitrophenols, benzenic and piridinic compounds. The good recoveries achieved with different water samples indicate that this assay can be a good alternative method for the determination of PCP in this kind of samples.     

Ultrasensitive assays of trans- and cis-β-carotenes in vegetable oils by high-performance liquid chromatography–thermal lens detection

The fact that β-carotene might be the protective factor against various cancers, suggests the need for a rapid reliable assay for this potential marker. We have proposed the method for selective, precise and simple profiling of carotenoids as well as for simultaneous ultrasensitive assaying of trans-β-carotene (TBC) and cis-β-carotene(s) (CBC) in five vegetable oils. The oil samples diluted 20 or 100 times were directly injected and analysed by means of the isocratic non-aqueous reversed-phase high-performance liquid chromatography (HPLC) combined with ultrasensitive thermal lens detection (TLS).

Elution of TBC was followed by CBC; both were identified and determined in olive, safflower, sesame, wheat germ and linseed oil by standard addition method. The presence of lutein/zeaxanthin, some xanthophyll and/or early eluting carotene may be also presumed in the aforementioned oils. The examined oils showed different and characteristic carotenoid/carotene profiles and characteristic TBC-to-CBC ratios. Both analytes were selectively detected in the presence of palmitic, oleic, linoleic, linolenic and stearic acid, β-sitosterol and --tocopherol. This extends applicability of the method to other vegetable oils as well.

Favourable analytical performances (high sensitivity, low limits of detection (LODs) and wide linearity span) enabled the direct analyses of highly diluted oils. This resulted in several major benefits of the proposed method, among which (i) reduced risk of stationary phase deterioration, (ii) avoiding the risk of carotenoids transformations and (iii) substantial labour and time savings. The TBC and CBC in diluted vegetable oils were reliably measured at ultratrace level (1–26 ng ml⁻¹) with the S/N ratio ranging from 4 to 140 and precisely determined (imprecision 0.4–8.3%). The concentrations of TBC+CBC estimated in the original oils were as follows: 90.5+51.2 ng ml⁻¹ in sesame oil, 146.0+164 ng ml⁻¹in safflower oil, 464.6+206.1 ng ml⁻¹in linseed oil, 453.7+143.3 ng ml⁻¹ in olive oil and 2.31+2.63 μg ml⁻¹ in wheat germ oil. The characteristic and variable portion of TBC within total β-carotene may serve as a reliable indicator of both, quality and authenticity of the vegetable oil. The HPLC–TLS assay proposed may therefore be successfully applied in nutritional, agricultural and epidemiological studies.     

Reverse flow injection spectrophotometric determination of iron(III) using norfloxacin

A reversed flow injection colorimetric procedure for determining iron(III) at the μg level was proposed. It is based on the reaction between iron(III) with norfloxacin (NRF) in 0.07 mol l⁻¹ ammonium sulfate solution, resulting in an intense yellow complex with a suitable absorption at 435 nm. Optimum conditions for determining iron(III) were investigated by univariate method. The method involved injection of a 150 μl of 0.04% w/v colorimetric reagent solution into a merged streams of sample and/or standard solution containing iron(III) and 0.07 mol l⁻¹ ammonium sulfate in sulfuric acid (pH 3.5) solution which was then passed through a single bead string reactor. Subsequently the absorbance as peak height was monitored at 435 nm. Beer's law obeyed over the range of 0.2–1.4 μg ml⁻¹ iron(III). The method has been applied to the determination of total iron in water samples digested with HNO₃–H₂O₂ (1:9 v/v). Detection limit (3σ) was 0.01 μg ml⁻¹ the sample through of 86 h⁻¹ and the coefficient of variation of 1.77% (n=12) for 1 μg ml⁻¹ Fe(III) were achieved with the recovery of the spiked Fe(III) of 92.6–99.8%.     

Spectrophotometric determination of tungsten(VI) enriched by nanometer-size titanium dioxide in water and sediment

The adsorption of W (VI) on different metal oxides (TiO₂, ZrO₂), different crystal form of TiO₂ (rutile, anatase) with high surface areas was studied and compared under different pH. A novel method for preconcentration of W (VI) with nanometer size titanium dioxide (rutile) and determination by spectrophotometry has been developed. W (VI) was selective adsorbed on 100 mg TiO₂ from 250 ml solution at pH 3.0, then eluted by 2 ml 9 mol l⁻¹ sodium hydroxide solution. The eluent was adjusted to 5 ml pH 0 solution, added 0.5 ml 12 mol l⁻¹ HCl, 0.3 ml 3% TiCl₃, 0.3 ml 50% NH₄SCN, stirred for 20 min, used for the analysis of W (VI) by measuring the absorbance at 402 nm with spectrophotometry, based on the chromogenic reaction between the W (VI) and the mixture of TiCl₃ and NH₄SCN. This method gave a concentration enhancement of 50 for 250 ml sample, eliminated the sizable interferences on direct determination with spectrophotometry. Detection limits (3σ, n=11) of 1.2 ng ml⁻¹, relative standard deviation of 2.3% at 10 ng ml⁻¹ level were obtained. The method was applied to determine the W (VI) in hot spring water, river water, tap water and stream sediment. Analytical recoveries of W (VI) added to samples were 98–101%.     

Preconcentration and determination of inorganic arsenic using a multisyringe flow injection system and hydride generation-atomic fluorescence spectrometry

A new multisyringe flow injection system for inorganic arsenic determination at trace levels by hydride generation-atomic fluorescence spectrometry (HGAFS) is presented. Preconcentration on a solid-phase was carried out using a column packed with an anion-exchange resin (Amberlite IRA-410). The reagents are dispensed to the system using a multisyringe burette coupled with two multi-port selection valves.

Different parameters were changing in order to make the system as effective as possible. An analytical curve was obtained for arsenic determination between 50 and 2000 ng l⁻¹. This new approach improved five times the sensitivity over a MSFIA–HGAFS technique developed previously by the authors. Detection limit of the proposed technique was (3σ_b/S) of 30 ng l⁻¹. The relative standard deviation (R.S.D.) of As at 1 μg l⁻¹ was 4.8% (n=7). A sample throughput of 10 h⁻¹ has been achieved. The proposed method has been applied to different reference solid and water materials with satisfactory results.     

Differential-pulse voltammetric determination of low μg l cyanide levels using EDTA, Cu(II) and a hanging mercury drop electrode

The proposed method for cyanide determination at the ultratrace level by differential pulse voltammetry is based in the sensitivity enhancement obtained when both Cu(II) and EDTA are present in the background electrolyte. Comparison of the detection limits and linear dynamic ranges using the conventional borate (pH 9.75), and the proposed borate-EDTA–Cu(II) background electrolytes was carried out. Best results have been obtained with the addition of 0.5 mmol l⁻¹ EDTA and 0.02 mmol l⁻¹ of Cu(II), which allow a detection limit of 1.7 μg l⁻¹ CN⁻ (65 nmol l⁻¹ — absolute detection limit 34 ng) with a precision better than ±2% for a 40 μg l⁻¹ level. Calibration range extended from detection limit up to 100 μg l⁻¹. Cyclic voltammetry indicates that the measured cyanide peak is obtained when the electrogenerated CuCN adsorbed onto the hanging mercury drop electrode surface, is oxidised at positive going potential scan. The method has been successfully applied to various industrial waste waters such as metal-finishing waste waters, water/sand mixtures from cleaning processes of coke production, leachates from wastes obtained from electrolytic cells of aluminium production, and liquors from gold extraction industry. Results obtained by the proposed method showed good agreement with those obtained by the standard methods (ion-selective potentiometry and the spectrophotometric pyridine method).     

Use of a peroxidase reactor in flow injection analysis for the determination of chloramine and the inhibition kinetics

A method for the determination of chloramine using a flow injection peroxidase reactor based on the inhibition reaction of the enzyme is developed. The immobilisation of the horseradish peroxidase is performed on the commercial polymer carrier VA Epoxy Biosynth. The peroxidase activity is detected photometrically based on the dehydration of the dye 2,2′-azino-di-[3-ethylenebenzthiazoline-6-sulphonate] (ABTS). The calibration of the method gives a linear concentration range from 0.026 to 1.04 mmol l⁻¹ (SD_n=3=below 5%). The detection limit was calculated to 26 μmol l⁻¹. A mixture out of competitive and non-competitive inhibition was analysed based on the Lineweaver–Burk plots.     

Development and application of a capillary electrophoresis-electrochemiluminescent method for the analysis of enrofloxacin and its metabolite ciprofloxacin in milk

Enrofloxacin (ENR) is a fluoroquinolone developed exclusively for the use in veterinary practice for the treatment of respiratory and gastrointestinal infections, and ciprofloxacin (CIP) is its main active metabolite. Their contents are regulated by the EU Council Regulation no. 2377/90 in animal edible tissues. We developed a sensitive and rapid method for the determination of ENR and CIP by capillary electrophoresis (CE) with electrochemiluminescence (ECL) detection. The method is based on the detection of aliphatic tertiary or secondary amino moieties in ENR and CIP with end-column tris(2,2-bipyridyl)ruthenium(II) electrochemiluminescence. Parameters that affect separation and detection were optimized. Under the optimized conditions, the calibration functions were linear in the range of 0.03–1 μg ml⁻¹ for ENR and 0.05–1.2 μg ml⁻¹ for CIP. The detection limits of ENR and CIR were 10 ng ml⁻¹ and 15 ng ml⁻¹, respectively, based on the signal-to-noise ratio of 3. The relative standard derivations of the peak height and the migration time for ENR and CIP were less than 4.13%. The developed method was successfully applied to determine ENR and CIP in milk with a solid-phase extraction procedure.     

Catalytic flow injection determination of vanadium by oxidation of N-(3-sulfopropyl)-3,3',5,5'-tetramethylbenzidine using bromate

A catalytic flow-injection (FI) method was developed for the determination of 10⁻⁹ mol l⁻¹ levels of vanadium(IV, V). The method is based on the catalytic effect of vanadium(V) on oxidation of N-(3-sulfopropyl)-3,3′,5,5′-tetramethylbenzidine (TMBZ·PS) using bromate as oxidant to form a yellow dye (λ_max=460 nm). The use of 5-sulfosalicylic acid (SSA) as an activator enhanced the sensitivity of the method. The calibration graphs with a working range 0.05–8.0 ng ml⁻¹ were obtained for vanadium(V). Vanadium(IV) was also determined, being oxidized by bromate. The detection limit (signal/noise, S/N=3) was 0.01 ng ml⁻¹ (ca. 2×10⁻¹⁰ mol l⁻¹) vanadium. The relative standard deviations (R.S.D.) for 15 determinations of 0.5 ng ml⁻¹ vanadium, and for ten determinations of 0.1 and 1.0 ng ml⁻¹ vanadium were 0.41, 2.6 and 0.25%, respectively, with a sampling rate of 15 samples h⁻¹. The proposed method was successfully applied to the determination of vanadium in natural waters.     

An intelligent flow analyser for the in-line concentration, speciation and monitoring of metals at trace levels

An intelligent and versatile flow system is proposed for the in-line speciation and/or concentration of metal ions at a wide range of concentrations without requiring manifold reconfiguration. On one hand, sample enrichment strategies are accomplished using packed-bed reactors, on the other hand speciation procedures are readily performed exploiting the selective complexation of the different oxidation states with the appropriate chromogenic reagents.

The potentials of the automated methodology were evaluated using the spectrophotometric monitoring of iron as a model of chemistry. Under the optimised physical and chemical variables, linear analytical curves over the ranges 0.025–0.5 or 2.0–40 mg l⁻¹ Fe were attained. The 3σ detection limit, the repeatability at the 0.5 mg l⁻¹ level, the enrichment factor for a sampling volume of 10 ml, and the maximum injection throughput were 8.4 ng ml⁻¹ Fe, 2.5%, 58.6 and 22 h⁻¹, respectively. The flowing system was applied to the speciation analysis of iron in waters, pharmaceutical formulations and agricultural products, using ICP-OES detection as an external reference method for total iron determination.

A remarkable feature of the expert system hereby presented is the ability to decide by itself if the pre-concentration and/or oxidation of the sample zone is required.