Understanding phenol adsorption mechanisms on activated carbons

The interactions between phenol molecules and activated carbons were investigated in order to understand the adsorption mechanism of this aromatic compound. A series of activated carbons with varied chemical composition but similar porous features were synthesized and submitted to phenol exposure from aqueous phase, followed by thermogravimetric analysis and identification of the desorbed species by temperature programmed desorption coupled with mass spectrometry. Based on these experiments, both physi- and chemisorption sites for phenol were identified on the activated carbons. Our results demonstrate that physisorption of phenol depends strictly on the porosity of the activated carbons, whereas chemisorption depends on the availability of the basal planes in the activated carbons. Thus, oxidation of the carbon can suppress the fraction of chemisorbed phenol since the surface functionalities incorporate to the edges of the basal planes; notwithstanding, hydrophilic carbons may present a small but not negligible contribution of chemisorbed phenol depending on the extent of the functionalization. Moreover, these adsorption sites (chemi-) are recovered by simply removal of the surface functionalities after thermal annealing.     

Role of surface chemistry in adsorption of phenol on activated carbons

Two samples of activated carbon of wood origin were oxidized using ammonium persulfate. The structural properties and surface chemistry of the samples and their oxidized counterparts were characterized using sorption of nitrogen and Boehm titration, respectively. Phenol adsorption from solution (at trace concentrations) was studied at temperatures close to ambient without maintaining a specific pH of the solution. The results showed, as expected, that the phenol uptake is dependent on both the porosity and surface chemistry of the carbons. Furthermore, phenol adsorption showed a strong dependence on the number of carboxylic groups due to two factors: (1) phenol reacts with carboxylic groups on the carbon surface, forming an ester bond, and (2) carboxylic groups on the carbon surface remove the pi-electron from the activated carbon aromatic ring matrix, causing a decrease in the strength of interactions between the benzene ring of phenol and the carbon's basal planes, which decreases the uptake of phenol.     

Calorimetric evaluation of activated carbons modified for phenol and 2,4-dinitrophenol adsorption

Two commercial activated carbons with differences in their superficial chemistry, one granular and the other pelletised, were modified for use in phenol and 2,4-dinitrophenol adsorption. In this paper, changes to the activated carbon surface will be evaluated from their immersion calorimetry in water and benzene, and they will then be compared with Area BET, chemical parameters, micropore size distributions and hydrophobicity factors of the modified activated carbons. The activated carbons were modified using 60 % solutions of phosphoric acid (H₃PO₄), nitric acid (HNO₃), zinc chloride (ZnCl₂) and potassium hydroxide (KOH); the activated carbon/solution ratio was 1:3 and impregnation was conducted 291 K for a period of 72 h before samples were washed until a constant pH was obtained. Water immersion calorimetry showed that the best results were obtained from activated carbons modified with nitric acid, which increased from ?10.6 to ?29.8 J g^?1 for modified granular activated carbon, and ?30.9 to ?129.3 J g^?1 for pelletised activated carbon. Additionally, they showed the best results in phenol and 2.4-dititrophenol adsorption. Those results indicate that impregnation with nitric acid under the employed conditions could generate a greater presence of oxygenated groups on their surface, which favours hydrogen bond formation and the increased adsorption of polar compounds. It should also be noted that immersion enthalpy in benzene for modified activated carbon with nitric acid is the method with the lowest value, which is consistent with the increased presence of polar groups on its surface. Regarding hydrophobicity factors, it was observed that granular carbons modified with nitric acid and potassium hydroxide have the lowest ratios, indicating greater interaction with water.     

Structural, textural and adsorption characteristics of nanosilica mechanochemically activated in different media

The structural, textural, and adsorption characteristics of mechanochemically activated (MCA) fumed silica A-300 as dry or water, ethanol, or water/ethanol-wetted powders (0.5 g of a solvent per gram of silica) in a ball mill for 1-6 h were studied in comparison with those of the initial powder. The MCA treatment enhances bulk density (ρ(b)) of the powder (from 0.045 g/cm(3) for the initial silica to 0.4 g/cm(3) for 6 h-MCA-treated water-wetted silica) depending on medium type and MCA time (t(MCA)). Stronger effects are observed for the MCA treatment of water-wetted silica than of dry or ethanol- or water/ethanol-wetted samples. The MCA treatment weakly affects the specific surface area (S(BET)). However, void (pore) size distribution, porosity, particle aggregation and size distribution in aqueous suspension, behavior of interfacial water, properties of poly(vinyl alcohol)/silica composites and adsorption of gelatin depend more strongly on the t(MCA) and ρ(b) values. Some of the observed changes in the characteristics (e.g., gelatin adsorption) depend on the ρ(b) value but are independent of the medium type used on the MCA. Other characteristics are nonlinear functions of both t(MCA) and ρ(b) values.     

Naphthalene adsorption on activated carbons using solvents of different polarity

The hydrophobic-hydrophilic character of a series of microporous activated carbons was explored as a key factor in competitive adsorption of a non-polar compound from liquid phase. The selectivity of the carbon surface towards naphthalene was explored by performing the adsorption isotherms in water, cyclohexane and heptane. Solvent polarity and adsorbent hydrophobic character were found to strongly influence the adsorption capacity of naphthalene. In aqueous media, despite the non-polar character of the adsorbate, surface acidity lowered adsorption capacity. This is attributed to the competition of water from the adsorption sites, via H-bonding with surface functionalities and the formation of hydration clusters that reduce the accessibility and affinity of naphthalene to the inner pore structure. In organic media the uptake decreased due to competition of the hydrophobic solvent for the active sites of the carbon and to solvation effects. This competitive effect of the solvent is minimized in oxidized carbons as opposed to the trend obtained in aqueous solutions. The results confirmed that although adsorption of naphthalene strongly depends on the narrow microporosity of the adsorbent, competitive adsorption of the solvent for the active sites becomes important.     

Adsorption of phenol by oil-palm-shell activated carbons

Steam activated carbons from oil-palm shells were prepared and used in the adsorption of phenol. The activated carbon had a well-developed mesopore structure which accounted for 45% of the total pore volume. The BET surface area of the activated carbon was 1183 m²/g and a total pore volume of 0.69 cm³/g using N₂ adsorption at 77 K. The adsorption capacity of the activated carbon for phenol was 319 mg/g of adsorbent at 298 K. The adsorption isotherms could be described by both the Langmuir-Freundlich and the Langmuir equations. The adsorption kinetics consisted of a rapid initial uptake phase, followed by a slow approach to equilibrium. A new multipore model is proposed that takes into account of a concentration dependent surface diffusion coefficient within the particle. This model is an improvement to the traditional branched pore model. The theoretical concentration versus time curve generated by the proposed model fitted the experimental data for phenol adsorption reasonably well. Phenol adsorption tests were also carried out on a commercial activated carbon known as Calgon OLC Plus 12×30 and the agreement between these adsorption data and the proposed model was equally good.     

Prediction of the micropore structure parameters and adsorption properties of activated carbons

A regularity govering variations of volume and linear size of micropores in carbon adsorbents during their vapor-gas activation was found. A parameter was proposed that characterizes the degree of development of the micropore system in activating carbons and an initial carbonized material. The parameter is defined as the number (or surface area) of micropores in the volume unit of the micropore zones. This parameter allows one to rationalize the choice of carbonized materials for the preparation of activated carbons with specified adsorption properties and to establish the range of activation beyond which the structure of the micropores loses stability. Furthermore, the parameter serves to predict how activation affects micropore structure parameters and adsorption properties of carbons. This in turn indicates the optimal degrees of microporosity of carbons needed to attain required adsorption properties.     

On the mechanisms of phenol adsorption by carbons

The removal of phenol and related compounds from dilute aqueous solutions by activated carbons corresponds to the coating of the micropore walls and of the external surface by a monolayer. This process is described by an analog of the Dubinin—Radushkevich—Kaganer equation. On the other hand, as suggested by immersion calorimetry at 293 K, in the case of concentrated solutions, the mechanism corresponds to the volume filling of the micropores, as observed for the adsorption of phenol from the vapor phase. The equilibrium is described by the Dubinin—Astakhov equation. It follows that the removal of phenol from mixtures with water depends on the relative concentrations, and the limiting factor for adsorption is either the effective surface area of the carbon, or the micropore volume.     

Comparisons of porous and adsorption properties of carbons activated by steam and KOH

In this work, fir woods and pistachio shells were used as source materials to prepare porous carbons, which were activated by physical (steam) and chemical (KOH) methods. Pore properties of these activated carbons including the BET surface area, pore volume, pore size distribution, and pore diameter were first characterized by a t-plot method based on N(2) adsorption isotherms. Highly porous activated carbons with BET surface area up to 1009-1096 m(2)/g were obtained. The steam and KOH activation methods produced carbons with mesopore content in the range 9-15 and 33-49%, respectively. The adsorption equilibria and kinetics of tannic acid, methylene blue, 4-chlorophenol, and phenol from water on such carbons at 30 degrees C were then investigated to check their chemical characteristics. The Freundlich equation gave a better fit to all adsorption isotherms than the Langmuir equation. On the other hand, the intraparticle diffusion model could best follow all adsorption processes. In comparison with KOH-activated carbons, it was shown that the rate of external surface adsorption with steam-activated carbons was significantly higher but the rate of intraparticle diffusion was much lower.     

Prediction of adsorption behavior of activated carbons

A study was made of the effect of temperature on predictive equations recently developed and applied to gas adsorption by beds of activated and impregnated carbons. Adsorption parameters, obtained for the adsorbate DMMP on small gram quantities of impregnated carbon at 25°C and applied to carbon bed breakthru times, were analyzed for changes resulting from direct temperature effects on gas diffusion, adsorption—desorption equilibria, volume expansion, relative pressure, and adsorbate—adsorbent interactions. Modifications in the adsorption parameters, calculated for bed temperatures ranging between 40.3 and 46.7°C, were used in the kinetic equations to predict breakthru times for M10 gas filters, each containing 13,847 g of carbon. The predicted values compared very well with those experimentally determined, the mean deviation in breakthru time being 5.82%, without regard to sign. A general analysis of a 10°C rise in temperature, from 25 to 35°C, for the M10 gas filter under the test conditions used, showed that the breakthru time would be lowered 20.0 min, 87% of this lowering due to a reduced adsorption rate constant, 9% due to a reduced adsorption capacity, and 4% due to volume expansion effects on concentration and flowrate.     

Reactive adsorption of penicillin on activated carbons

A series of activated carbons with varied surface chemistry, obtained by wet oxidation and thermal treatment, was used for the removal of penicillin from low concentration aqueous solution. It was found that the carbon surface chemistry favors the degradation of the antibiotic, giving rise to various intermediates detected both in solution and in the adsorbed phase (deposited with the pore structure of the activated carbons). The confinement of penicillin molecules entrapped in the nanopores of activated carbons of acidic nature accelerates their degradation compared to that one in the bulk solution, which can be linked the strong local pH fall inside the pores. Degradation also takes place in activated carbons of basic pH, although the nature and partition of the intermediates formed differ from those in the acidic carbons. In both cases most of the breakdown products do not present therapeutic activity.     

Effects of pyrolysis conditions on the physical characteristics of oil-palm-shell activated carbons used in aqueous phase phenol adsorption

Oil-palm shells, a biomass by-product from palm-oil mills, were converted into activated carbons by vacuum or nitrogen pyrolysis, followed by steam activation. The effects of pyrolysis environment, temperature and hold time on the physical characteristics of the activated carbons were studied. The optimum pyrolysis conditions for preparing activated carbons for obtaining high pore surface area are vacuum pyrolysis at a pyrolysis temperature of 675 °C and 2 h hold time. The activation conditions were fixed at a temperature of 900 °C and 1 h hold time. The activated carbons thus obtained possessed well-developed porosities, predominantly microporosities. For the pyrolysis atmosphere, it was found that significant improvement in the surface characteristics of the activated carbons was obtained for those pyrolysed under vacuum. Adsorption capacities of activated carbons were determined using phenol solution. For the activated carbons pyrolysed under optimum vacuum conditions, a maximum phenol adsorption capacity of 166 mg/g of carbon was obtained. A linear relationship between the BET surface area and the adsorptive capacity was shown.     

Energetics of methane adsorption on microporous activated carbons

The influence of microporous carbon surface oxidation on energetics of methane adsorption at 308 K is discussed. Obtained adsorption heats and integral molar entropies of the adsorbate show that microporous carbon surface oxidation changes the methane adsorption process. This is probably resulted by the existence of an endothermic effect during adsorption in oxidized carbon micropores.     

Kinetic,isothermal and thermodynamic studies on Th(IV) adsorption by different modified activated carbons

In this study, the performance of modified adsorbents obtained from activated carbon for the adsorption of thorium(IV) ions from aqueous media was investigated. The analytical and spectroscopic methods such as FT-IR, BET, SEM and UV–Vis were used to examine the properties of the modified materials. According to the analysis results, the both adsorbents had large surface areas after modification. Then, temperature, pH, mixing time and solution concentration parameters were observed to determine optimum thorium adsorption conditions on modified materials. The obtained results from the experiments were applied different three kinetic models and adsorption isotherms and thermodynamic parameters were calculated and then all of the results were interpreted. The adsorption process for both adsorption systems was observed to be compatible with the pseudo-second-order kinetic model. The adsorption equilibrium data were best described by the Langmuir model for modified adsorbent with KMnO₄ and by the Freundlich model for modified adsorbent with NaOH. Furthermore, the calculated thermodynamic parameters (ΔG°, ΔH° and ΔS°) showed that the both adsorption processes were endothermic and spontaneous. The data show that modified adsorbents can be used as influential and low-cost adsorbents to remove thorium ion. Modified new adsorbents were highly selective for thorium ion in competitive adsorption studies.

     

Comparative study on composition, structure, and adsorption behavior of activated carbons derived from different synthetic waste polymers

The composition, structure, and adsorption behavior of activated carbons (ACs) derived from three different types of waste polymers, i.e., tire rubber (TR), polyvinyl chloride (PVC), and polyethyleneterephtalate (PET), by KOH activation were compared. The AC derived from PET exhibited the largest surface area (2831 m(2)/g) and pore volume (1.68 cm(3)/g) due to the homogenous aromatic composition of PET. The AC derived from PVC exhibited relatively lower surface area (2666 m(2)/g) but more narrowed pore size distribution (2-3 nm). The complex composition and high ash content of tire particles resulted in AC product with significantly lower surface area (398.5 m(2)/g) and heterogeneous pore width. Adsorption data of methylene blue (MB) were fitted well by Langmuir equation, indicating monolayer coverage on the ACs. The high oxygen content of PET-derived AC heavily affected its adsorption to MB and iodine. Due to the remarkable surface area and highly mesoporous structures, ACs based on both PET and PVC exhibited much higher adsorption capacities than that of TR and commercial coal-based AC (F400). This study demonstrates that the properties of ACs are highly dependent on their starting polymers and the potential of converting synthetic polymer waste into effective adsorbents for environmental remediation and cleanup.     

Palladium catalysts supported on activated carbon with different textural and surface chemical properties

A commercial activated carbon was used as catalyst support in Pd/AC catalysts. The effects of the different surface oxygen groups and textural properties of the carbon supports on the metal dispersion of the supported catalysts were analyzed.     

Structural characteristics of modified activated carbons and adsorption of explosives

Several series of activated carbons prepared by catalytic and noncatalytic gasification and subsequent deposition of pyrocarbon by pyrolysis of methylene chloride or n-amyl alcohol were studied by FTIR, chromatography, and adsorption methods using nitrogen and probe organics (explosives). The relationships between the textural characteristics of carbon samples and the recovery rates (eta) of explosives on solid-phase extraction (SPE) using different solvents for their elution after adsorption were analyzed using experimental and quantum chemical calculation results. The eta values for nitrate esters, cyclic nitroamines, and nitroaromatics only partially correlate with different adsorbent parameters (characterizing microporosity, mesoporosity, pore size distributions, etc.), polarity of eluting solvents, or characteristics of probe molecules, since there are many factors strongly affecting the recovery rates. Some of the synthesized carbons provide higher eta values than those for such commercial adsorbents as Hypercarb and Envicarb.     

Activated carbons obtained from agro-industrial waste: textural analysis and adsorption environmental pollutants

In this study, we aimed to use as a new lignocellulosic precursor in the production of activated carbon. The physicochemical characteristics of the activated carbons obtained under optimum conditions were determined by using some techniques such as thermo-gravimetric (TG/DTG) analysis, nitrogen adsorption–desorption, scanning electron microscopy (SEM) and surface functional group analysis by Fourier transform infrared spectroscopy (FT-IR), Boehm titration method and point of zero charge (pHpzc). In addition, the activated carbons were tested to remove phenols from aqueous solutions. The results indicated that activated carbon the orange peel, pine cone and yerba mate, could be employed as an alternative low-cost activated carbon for the removal the phenolic contaminants from wastewater.