A highly sensitive method for determination of paracetamol by adsorptive stripping voltammetry using a carbon paste electrode modified with nanogold and glutamic acid

A reliable and simple sensor was fabricated by modifying a carbon paste electrode with nanosized gold particles and poly (glutamic acid) for determination of paracetamol (PAR). The modified electrode exhibited an effective catalytic response to the oxidation and reduction of PAR with good reproducibility and stability. The determination was carried out by differential pulse adsorptive stripping voltammetry after a 30 s accumulation time with an open circuit potential and under stirring. The calibration curve is linear in the range from 0.05 to 70 μM of PAR (with a correlation coefficient of 0.9990), and the sensitivity is 1.51 μA·μM^-1. The modified electrode was used to detect PAR in commercial tablets.     

Electrochemical behavior of tartaric acid at CuGeO3 nanowire modified glassy carbon electrode

The electrochemical behavior of tartaric acid at the CuGeO₃ nanowire modified glassy carbon electrode has been investigated by cyclic voltammetry (CV). The results show that two pairs of semireversible electrochemical peaks are observed and can be assigned to the process of oxidation–reduction and adsorption–desorption of tartaric acid at the modified glassy carbon electrode, respectively. The intensity of the CV peaks increases linearly with the increase of the content of tartaric acid in the range of 0.01–5 mM and scan rate ranging from 25–200 mV s^?1. CuGeO₃ nanowire modified glassy carbon electrode exhibits good detection ability for tartaric acid in neutral solution with the detection limit of 8.9 and 7.7 μM for cvp1 and cvp2, respectively, at a signal-to-noise ratio of 3. The CuGeO₃ nanowire modified glassy carbon electrode has good reproducibility and stability.     

Electrochemical behavior and voltammetric determination of L-tryptophan and L-tyrosine using a glassy carbon electrode modified with single-walled carbon nanohorns

We report a simple method for the direct and quantitative determination of L-tryptophan (Trp) and L-tyrosine (Tyr) using a glassy carbon electrode (GCE) modified with single-walled carbon nanohorns (SWCNHs). The SWCNH modified GCE exhibits high electrocatalytic activity towards the oxidation of both Trp and Tyr. It shows a linear response to Trp between 0.5 and 50 μM and to Tyr between 2 and 30 μM. The detection limits for Trp and Tyr are 50 nM and 400 nM, respectively. In addition, the modified GCE displays good selectivity and good sensitivity, thus making it suitable for the determination of Trp and Tyr in spiked serum samples.

Electrochemistry and voltammetric determination of L-tryptophan and L-tyrosine using a glassy carbon electrode modified with a Nafion/TiO2-graphene composite film

We describe a glassy carbon electrode (GCE) modified with a film composed of Nafion and TiO₂-graphene (TiO₂-GR) nanocomposite, and its voltammetric response to the amino acids L-tryptophane (Trp) and L-tyrosine (Tyr). The incorporation of TiO₂ nanoparticles with graphene significantly improves the electrocatalytic activity and voltammetric response compared to electrodes modified with Nafion/graphene only. The Nafion/TiO₂-GR modified electrode was used to determine Trp and Tyr with detection limits of 0.7 and 2.3 μM, and a sensitivity of 75.9 and 22.8 μA mM^?1 for Trp and Tyr, respectively.

Highly sensitive hydrogen peroxide sensor based on a glassy carbon electrode modified with platinum nanoparticles on carbon nanofiber heterostructures

We are presenting a sensor for hydrogen peroxide (H₂O₂) that is based on the use of a heterostructure composed of Pt nanoparticles (NPs) and carbon nanofibers (CNFs). High-density Pt NPs were homogeneously loaded onto a three-dimensional nanostructured CNF matrix and then deposited in a glassy carbon electrode (GCE). The resulting sensor synergizes the advantages of the conducting CNFs and the nanoparticle catalyst. The porous structure of the CNFs also favor the high-density immobilization of the NPs and the diffusion of water-soluble molecules, and thus assists the rapid catalytic oxidation of H₂O₂. If operated at a working voltage of −0.2 V (vs. Ag/AgCl), the modified GCE exhibits a linear response to H₂O₂ in the 5 μM to 15 mM concentration range (total analytical range: 5 μM to 100 mM), with a detection limit of 1.7 μM (at a signal-to-noise ratio of 3). The modified GCE is not interfered by species such as uric acid and glucose. Its good stability, high selectivity and good reproducibility make this electrode a valuable tool for inexpensive amperometric sensing of H₂O₂.

The Pt NPs/CNF heterostructure-based H₂O₂ sensor synergizes the advantages of both the conducting carbon nanofibers and the nanoparticle catalyst. The 3D structure of the nanofibers favor high density immobilization of the nanoparticles and penetration by water-soluble molecules, which assists the catalyic oxidation of H₂O₂. The sensor shows outstanding performance in terms of detection range, detection limit, response time, stability and selectivity.

     

Electrochemical determination of nitrite via covalent immobilization of a single-walled carbon nanotubes and single stranded deoxyribonucleic acid nanocomposite on a glassy carbon electrode

A novel method has been developed for determination of nitrite by modifying the surface of a glassy carbon electrode (GCE) using single-walled carbon nanotubes with covalently immobilized single-strand deoxyribonucleic acid. The modified electrodes were characterized by field emission scanning electron microscopy, X-ray photoelectron spectroscopy, and electrochemical techniques. The results demonstrate that the nanotube-DNA nanocomposite has been successfully immobilized on the surface of the GCE. The new electrode, under optimum conditions at room temperature, exhibits excellent electrocatalytic activity towards the oxidation of nitrite, with a significantly reduction of the overpotential. The linear range for the detection of nitrite is from 0.6 to 540 μM, with a sensitivity of 0.216 μA?μM^?1, and a detection limit as low as 0.15 μM. The electrode showed good reproducibility and high stability and was successfully used to analyze nitrite in water and sausage samples.     

Simultaneous sensing of L-tyrosine and epinephrine using a glassy carbon electrode modified with nafion and CeO2 nanoparticles

An electrochemical sensor was developed and tested for detection of L-tyrosine in the presence of epinephrine by surface modification of a glassy carbon electrode (GCE) with Nafion and cerium dioxide nanoparticles. Fabrication parameters of a surfactant-assisted precipitation method were optimized to produce 2–3 nm CeO₂ nanoparticles with very high surface-to-volume ratio. The resulting nanocrystals were characterized structurally and morphologically by X-ray diffractometery (XRD), scanning and high resolution transmission electron microscopy (SEM and HR-TEM). The nanopowder is sonochemically dispersed in a Nafion solution which is then used to modify the surface of a GCE electrode. The electrochemical activity of L-tyrosine and epinephrine was investigated using both a Nafion-CeO₂ coated and a bare GCE. The modified electrode exhibits a significant electrochemical oxidation effect of L-tyrosine in a 0.2 M Britton-Robinson (B-R) buffer solution of pH 2. The electro-oxidation peak current increases linearly with the L-tyrosine concentration in the molar concentration range of 2 to 160 μM. By employing differential pulse voltammetry (DPV) for simultaneous measurements, we detected two reproducible peaks for L-tyrosine and epinephrine in the same solution with a peak separation of about 443 mV. The detection limit of the sensor (signal to noise ratio of 3) for L-tyrosine is ~90 nM and the sensitivity is 0.20 μA μM⁻¹, while for epinephrine these values are ~60 nM and 0.19 μA μM⁻¹. The sensor exhibited excellent selectivity, sensitivity, reproducibility and stability as well as a very good recovery time in real human blood serum samples.

Simultaneous electrochemical determination of L-tyrosine and epinephrine in blood plasma with Nafion-CeO₂/GCE modified electrode showing a 443 mV peak-to-peak potential difference between species oxidation peak currents.

     

A <Emphasis Type="SmallCaps">l</Emphasis>-tryptophan sensor based on tellurium nanorods modified glassy carbon electrode

An electrochemical l-tryptophan sensor based on tellurium nanorods modified glassy carbon electrode was proposed. The tellurium nanorods were synthesized by a chemical reduction method. The morphology and structures of the nanorods were characterized by scanning electron microscope (SEM) and transmission electron microscope (TEM). Owing to the special structure of the tellurium nanorods, the sensor exhibits excellent electrocatalytic ability towards the oxidation of l-tryptophan and shows linearity in the range from 0.02 to 11.48 μM with a sensitivity of 256 μA mM^?1 cm^?2 with a correlation coefficient of 0.9945. The detection limit was 0.01 μM with signal-to-noise ratio of 3, and the response time was found to be 2 s. Moreover, the sensor also exhibited long-term stability, good reproducibility and anti-interference, thus holding promise for sensing of l-tryptophan in practice.     

Fabrication and characterization of poly 2-napthol orange film modified electrode and its application to selective detection of dopamine

The present work is based on the use of a redox mediator containing an azo group for the selective determination of dopamine in the presence of uric acid and ascorbic acid by electrochemical method. A modified electrode was prepared by electrochemical polymerization of the poly 2-napthol orange film (P2NO) on the paraffin wax-impregnated graphite electrode (PIGE) by applying potential between ?0.6 and 0.8 V at scan rate of 50 mV s^?1 for 30 segments. The modified P2NO film electrode was characterized by ATR-IR spectroscopy, FE-SEM, cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), differential pulse voltammetry (DPV), hydrodynamic voltammetry (HDV), and chronoamperometry (CA). The P2NO film modified electrode exhibited selective determination of dopamine in the presence of uric acid and ascorbic acid, and the electrocatalytic activity for oxidation of dopamine was excellent. The linear range for the determination of dopamine was 0.6 to 250 μM with a limit of detection of 0.13 μM. The modified P2NO electrode showed good stability and reproducibility. The modified electrode was used for real sample analysis such as human blood serum, rat blood serum, and pharmaceutical samples (dopamine hydrochloride injection). The results obtained were found to be satisfactory.     

A highly sensitive nonenzymatic glucose sensor based on nickel oxide–carbon nanotube hybrid nanobelts

In this study, we demonstrated a highly sensitive electrochemical sensor for the determination of glucose in alkaline aqueous solution by using nickel oxide single-walled carbon nanotube hybrid nanobelts (NiO–SWCNTs) modified glassy carbon electrode (GCE). The hybrid nanobelts were prepared by the deposition of SWCNTs onto the Ni(SO₄)_0.3(OH)_1.4 nanobelt surface, followed by heat treatment at different temperatures ranging from 400 °C to 600 °C. The NiO–SWCNTs hybrid nanobelts modified electrode prepared at 500 °C displays enhanced electrocatalytic activity towards glucose oxidation, revealing a synergistic effect between the NiO and the deposited SWCNTs. The as-fabricated nonenzymatic glucose sensor exhibits excellent glucose sensitivity (2,980 μA cm^?2 mM^?1), lower detection limit (0.056 μM, signal/noise [S/N] ratio?=?3), and wider linear range (0.5–1,300 μM). Moreover, the sensor has been successfully used for the assay of glucose in serum samples with good recovery, ranging from 96.4 % to 102.4 %.     

A conductive crosslinked graphene/cytochrome c networks for the electrochemical and biosensing study

The direct electrochemistry of catalytically active cytochrome C (Cyt c) adsorbed together with a 3-dimensional network of chemically synthesized graphene on glassy carbon electrode has been readily obtained in aqueous phosphate buffer. Direct electrical communication between the redox center of Cyt c and the modified graphene-based electrode was established. The modified electrode was employed as a high-performance hydrogen peroxide (H₂O₂) biosensor. The Cyt c present in modified electrode exhibited a pair of quasi-reversible redox peaks with a midpoint potential of ?0.380 and ?0.2 V, cathodic and anodic, respectively. Investigations into the electrocatalytic activity of the modified electrode upon hydrogen peroxide exposure revealed a rapid amperometric response (5 s). Under optimized conditions, the linear range of response to H₂O₂ concentration ranged from 5 × 10^?7 to 2 × 10^?4 M with a detection limit of 2 × 10^?7 M at a signal-to-noise ratio of 3. The stability, reproducibility, and selectivity of the proposed biosensor are discussed in relation to the morphology and composition of the modified electrode.     

A highly stable nano γ-Fe2O3/gold-film modified electrode for electrochemically sensitive sensing to hydrazine

The magnetic γ-Fe₂O₃ material was prepared in a new way and characterized by transmission electron microscopy and X-ray diffraction. It was modified on a glass carbon electrode (GCE) coated with gold film to form nano γ-Fe₂O₃/Au/GCE. The electrooxidation of hydrazine has been deeply explored with the resulting electrode in 0.1 M phosphate-buffered saline (pH 7.0). The affecting factors containing pH of supporting electrolyte, scan rate, deposition time, amount of γ-Fe₂O₃, and possible interferences were investigated, and the oxidation mechanisms of hydrazine on the γ-Fe₂O₃/Au/GCE were also explored. The amperometric response to hydrazine is linear in the range of 0.02 to 11 μM, and the detection limit is 6 nM at a SNR of 3. The prepared sensor exhibited good sensitivity, stability, and lower detection limit for the determination of hydrazine injection.     

Amperometric nonenzymatic glucose sensor based on a glassy carbon electrode modified with a nanocomposite made from nickel(II) hydroxide nanoplates and carbon nanofibers

We report on a highly sensitive and selective nonenzymatic glucose sensor based on a glassy carbon electrode modified with a composite prepared from nickel(II) hydroxide nanoplates and carbon nanofibers. The nanocomposite was characterized by scanning electron microscopy and powder X-ray diffraction. Electrodes modified with pure Ni(OH)₂ and with the nanocomposite were characterized by electrochemical impedance spectroscopy. Cyclic voltammetric and amperometric methods were used to investigate the catalytic properties of the modified electrodes for glucose electrooxidation in strongly alkaline solution. The sensor exhibits a wide linear range (from 0.001 to 1.2 mM), a low detection limit (0.76 μM), fast response time (< 5 s), high sensitivity (1038.6 μA?·?mM^?1?·?cm^?2), good reproducibility, and long operational stability. Application of the nonenzymatic sensor for monitoring glucose in real samples was also demonstrated.

Poly(m-ferrocenylaniline) modified carbon nanotubes-paste electrode encapsulated in nafion film for selective and sensitive determination of dopamine and uric acid in the presence of ascorbic acid

A nafion covered carbon nanotubes-paste electrode modified with poly(m-ferrocenylaniline), (Nf/p(FcAni)-CNTsPE), provides a novel voltammetric sensor for the selective determination of dopamine (DA) and uric acid (UA) in the presence of ascorbic acid (AA). We studied the electrochemical activity of Nf/p(FcAni)-CNTsPE toward DA, UA, and AA by differential pulse voltammetry (DPV). DA and UA anodic peaks appear at 0.30 and 0.45 V, respectively while an anodic peak for AA was not observed. DPV oxidation peak values are linearly dependent on DA concentration over the range 1–150 μM (r² = 0.992), and on UA concentration over the range 5–250 μM (r² = 0.997). DA and UA detection limits are estimated to be 0.21 and 0.58 μM, respectively. The modified electrode shows both good selectivity and reproducibility for the selective determination of DA and UA in real samples. Finally, the modified electrode was successfully applied for the determination of DA and UA in pharmaceutical or biological sample fluids.     

Amperometric sensor for ascorbic acid based on a glassy carbon electrode modified with gold-silver bimetallic nanotubes in a chitosan matrix

We report on an amperometric sensor for ascorbic acid (AA) that is based on highly dense gold-silver nanotubes in a chitosan film on a glassy carbon electrode. The nanotubes were synthesized by a poly(vinyl pyrrolidone)-mediated polyol method employing a replacement reaction with silver nanowires as templates, and were characterized by scanning electron microscopy, energy-dispersive X-ray spectroscopy, and X-ray diffraction. Under the optimal conditions, the sensor exhibits good electrocatalytic activity towards the oxidation of AA, and this enables the determination of AA in the 5 μM to 2 mM concentration range, with a detection limit at 2 μM (at an S/N of 3). The response time is 2 s. The sensor displays good reproducibility, selectivity, sensitivity, and long-term stability.

A sensitive and selective nitrite sensor based on a glassy carbon electrode modified with gold nanoparticles and sulfonated graphene

We describe a highly sensitive and selective amperometric sensor for the determination of nitrite. A glassy carbon electrode was modified with a composite made from gold nanoparticles (AuNPs) and sulfonated graphene (SG). The modified electrode displays excellent electrocatalytic activity in terms of nitrite oxidation by giving much higher peak currents (at even lower oxidation overpotential) than those found for the bare electrode, the AuNPs-modified electrode, and the SG-modified electrode. The sensor has a linear response in the 10 μM to 3.96 mM concentration range, a very good detection sensitivity (45.44 μA mM^?1), and a lower detection limit of 0.2 μM of nitrite. Most common ions and many environmental organic pollutants do not interfere. The sensor was successfully applied to the determination of nitrite in water samples, and the results were found to be consistent with the values obtained by spectrophotometry.

The Electrochemical Behavior of Neurotransmitters at a Poly (Pyrrole‐ β‐Cyclodextrin) Modified Glassy Carbon Electrode

Abstract

A glassy carbon electrode surface was modified with an electropolymerized film made of pyrrole and β‐cyclodextrin 1∶1, in a 0.1 M LiClO₄ solution using cyclic voltammetry. The resulting modified electrode (Ppy/β‐CD) exhibits interesting electrocatalytic activity toward the electrochemical oxidation of neurotransmitters such as dopamine (DA) and norepinephrine (NE). Well‐resolved and reversible cyclic voltammograms (CVs) were obtained for these organic compounds in a 0.1 M H₂SO₄ solution. The effect of the pH on the voltammetric response of DA and NE was also investigated inside the range of pH 2.8–8.4. The oxidation current of norepinephrine increase linearly with the concentration inside the range of 4×10^?7 M–2×10^?6 M. The oxidation current of dopamine also followed the same trend range of 2×10^?6 M–10^?5 M. The detection limit was 6×10^?6 M for (DA) and 8×10^?7 M for (NE). As an example, the relative standard deviation for 1×10^?5 M of DA was 2.056%. The diffusion coefficients D for the molecules studied were determined by means of the measurement of the effect of the scan rate on the CVs of the neurotransmitters. All the results showed that the electron transfer was predominantly diffusion controlled at the conducting polymer/solution interface.

Interference phenomenon due to ascorbic acid (AA) toward the neurotransmitters was also investigated. The novel modified electrodes presented capability to resolve perfectly the AA and neurotransmitters oxidation peaks. This performance could be achieved even at a concentration 20 times higher than the neurotransmitters.

Finally, the newly fabricated Ppy/β‐CD film exhibits interesting analytical performances compared with other systems in the literature, such as higher sensitivity, rapid response, good mechanical stability and reproducibility.     

Nonenzymatic sensor for glucose based on a glassy carbon electrode modified with Ni(OH)2 nanoparticles grown on a film of molybdenum sulfide

A glassy carbon electrode (GCE) was modified with nickel(II) hydroxide nanoparticles and a film of molybdenum sulfide. The nanocomposite was prepared by two-step electrodeposition. Scanning electron microscopy reveals that the nanoparticles are uniformly deposited on the film. Cyclic voltammetry and chronoamperometry indicate that this modified GCE displays a remarkable electrocatalytic activity towards nonenzymatic oxidation of glucose. Response is linear in the 10–1,300 μM concentration range (R ² ?=?0.9987), the detection limit is very low (5.8 μM), response is rapid (< 2 s), and selectivity over ascorbic acid, dopamine, uric acid, fructose and galactose is very good.

Sensitive voltammetric determination of rutin at a carbon nanotubes-ionic liquid composite electrode

A new composite electrode of multiwall carbon nanotubes (MWNTs) and 1-dodecyl-3-methylimidazolium hexafluorophosphate (DDMIMPF₆) was fabricated to determine rutin. This electrode showed very attractive electrochemical performances compared to other kinds of ionic liquid modified electrodes and notably improved sensitivity and stability. Electrochemical behavior of rutin at the composite electrode had been investigated in pH 2.09 Britton–Robinson buffer solution by cyclic voltammetry and square wave voltammetry. The experimental results suggested that the composite electrode exhibited an electrocatalytic activity toward the redox of rutin. The electrochemical parameters of rutin were calculated with the results of the charge transfer coefficient (α) and the standard rate constant (k _s) as 0.48 and 2.09 s^?1. Under the selected conditions, the reduction peak current was linearly dependent on the concentration of rutin in the range of 0.03–1.5 μM, with a detection limit of 0.01 μM (S/N?=?3). The relative standard deviation for six times successive determination of 1 μM rutin was 1.6 %. The method was successfully applied to the determination of rutin in tablets and urine samples without the influence of the coexisting substances. In addition, the MWNTs/DDMIMPF₆ composite electrode exhibits a distinct advantage of simple preparation, surface renewal, good reproducibility, and stability.     

Lead-doped carbon ceramic electrode as a renewable surface composite electrode for the preparation of lead dioxide film and detection of <Emphasis Type="SmallCaps">l</Emphasis>-tyrosine

Lead-doped carbon ceramic electrode as a new type of renewable composite electrode was prepared by mixing the lead powder with electrode matrix before gelation. Pb on the electrode surface was then converted to lead dioxide by the potential scanning of the composite electrode in 0.1 M NaOH solution in the range of ? 0.3 to 0.7 V versus SCE. The composition and morphology of the electrodes were studied by energy dispersive X-ray spectrometry, scanning electron microscopy, and atomic force microscopy techniques. Cyclic voltammetry and chronoamperometry techniques were also used to study the electrocatalytic activity of the modified electrode toward the oxidation of the l-tyrosine. The best results were obtained at a working potential of 0.45 V (vs. SCE) in 0.1 M NaOH solution. The sensor exhibited a good linear response in the range of 5–1458 µM with a coefficient of determination of 0.9963. The detection limit was 0.77 µM, and sensitivity was 37.4 μA mM^?1. In addition, the modified electrode showed high stability and interference-free response for to detection of the l-tyrosine.