基于数字全息和数字图像相关方法的面内位移测量

针对一套数字全息装置只能测量离面位移这一个维度位移的局限性问题,将数字全息与数字图像相关方法相结合,利用数字全息重建的强度图像,实现了面内另外两个维度位移的测量,拓宽了一套数字全息装置的测量能力.该方法对待测物体位移前后的全息图数值重建得到两幅强度图,然后对变形前后的强度图应用数字图像相关方法得到面内两个维度位移的测量...     

数字全息干涉法流体质扩散系数实验研究

本文首先对数字全息干涉术中的数字图像处理理论以及数字全息干涉法实验原理作了详细研究.在此基础上,对数字图像处理中全息图的预处理、全息图像的频域滤波、数字干涉条纹再现等关键技术做了详细阐述.自行设计和搭建了数字全息干涉法流体质扩散系数测量实验台.以0.33 mol·L-1的氯化钾溶液-水的扩散体系作为标准物质,测量了其质扩散系数.结果显示,与文献数据比较测量相对偏差绝对平均值为1.30%,验证了实验台的可靠性.     

基于滤波成像的大视角数字全息技术

为提高数字全息再现像视角,提出一种基于滤波成像的数字全息技术来实现大视角的三维物体面型测量.利用离轴像面数字全息技术,通过在4F相干图像处理系统的空间频谱面处放置可移动的低通滤波器,使满足CCD分辨率的物光波与参考光波干涉形成全息图,并控制低通滤波及成像区域分别记录不同谱段的子全息图.再现时,首先对子全息图进行数字傅里叶变换,重构对应频谱段,并对频谱段进行拼接形成完整的物光频谱;而后通过数字再现获得大视角的数字全息再现像.利用该方法测量了圆柱形表面(光滑的缝纫针)的三维形貌,并取得了较好的实验结果.     

基于滤波成像的大视角数字全息技术

为提高数字全息再现像视角,提出一种基于滤波成像的数字全息技术来实现大视角的三维物体面型测量.利用离轴像面数字全息技术,通过在4F相干图像处理系统的空间频谱面处放置可移动的低通滤波器,使满足CCD分辨率的物光波与参考光波干涉形成全息图,并控制低通滤波及成像区域分别记录不同谱段的子全息图.再现时,首先对子全息图进行数字傅里叶变换,重构对应频谱段,并对频谱段进行拼接形成完整的物光频谱|而后通过数字再现获得大视角的数字全息再现像.利用该方法测量了圆柱形表面（光滑的缝纫针）的三维形貌,并取得了较好的实验结果.     

基于POCS的数字全息显微系统的超分辨实验研究

为提高数字全息显微系统的重建效果,将凸集投影算法应用于数字全息中,以实现数字全息的超分辨重建.首先,在数字全息和凸集投影法的理论基础上,搭建透射式离轴数字全息显微实验光路.然后,利用分辨率板验证凸集投影法在全息图超分辨率复原中的有效性.最后,通过微透镜阵列验证该方法在三维重建中的可行性.将参考全息图的三维重建结果,分别与低分辨率全息图和超分辨率复原全息图的重建结果进行残差估计.结果表明,后者残差的峰谷值和均方根值相比前者分别降低了36.88%和70.66%,证明该方法能够实现数字全息的超分辨重建.     

压缩感知重建数字同轴全息

数字重建是数字全息技术的关键步骤.传统的重建算法存在共轭像、聚焦物体与背景离焦物体相互干扰等问题.应用新兴的压缩感知技术,研究了全息图像的稀疏重建.基于衍射的线性运算,导出了利用压缩感知重建数字同轴全息三维空间的算法.利用该算法对颗粒的模拟全息图和数字显微全息实验全息图进行了重建,并将重建结果与传统的卷积重建结果进行了...     

多模式光学数字全息实验教学系统

研究设计了一种多模式现代光学数字全息成像实验教学系统.该系统可通过多光路模式与CcD技术相结合建立并记录数字全息图频率场,采用不同数学算法和程序实现全息图的全数字化重构再现与图像的三维测量,并通过界面设计详细演示数字全息成像的原理与过程.     

动态数字彩虹全息显示的研究

提出一种动态数字彩虹全息显示术,该技术将计算机制全息术和动态双视彩虹全息合成术相结合,根据彩虹全息的基元全息图为“线全息图”以及双眼立体视觉的特点,计算物点的线全息图上两个片断,使得两个全息图片断分别对应左右眼视图,同时对彩虹全息图的狭缝像进行横向分割,使得不同区域成为物体不同姿态的视窗,从而达到动态显示的效果.给出了数字动态全息的计算方法,并得到了初步的实验结果.     

基于DMD的数字全息显示及其再现像质增强

采用DMD作为空间光调制器构建了一套数字全息显示系统.分析了数字全息图光学再现中影响再现图像质量的因素,提出了一种采用频域滤波重建高条纹对比度滤波全息图来改善其光学再现图像质量的新方法.采用信噪比及图像亮度作为评价参量,对原始全息图和滤波全息图的数值再现像进行定量分析表明,滤波后全息图的再现像质量明显优于原始全息图的再现像.基于DMD数字全息显示系统的光学再现实验也验证了理论分析结果.     

超分辨率数字全息实验研究

为提高全息成像的分辨率,对超分辨率数字全息进行实验研究,介绍了全息和超分辨率的基本理论。试验中以激光二极管尾纤发射端作为点光源,采用非放大的光路系统,拍摄了一组亚像素位移的LR全息图。通过对LR全息图和SR全息图重建的结果对比,结果显示该方法能够实现全息图亚像素位移,经超分辨率重建的图像分辨率明显提升。通过使用更高精度的位移装置和更有针对性的超分辨率算法将会进一步提升效果。     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.     

A stereo matching algorithm using multi-peak candidate matches and geometric constraints

Gray cross correlation matching technique is adopted to extract candidate matches with gray cross correla- tion coefficients less than some certain range of maximal correlation coefficient called multi-peak candidate matches. Multi-peak candidates are extracted corresponding to three closest feature points at first. The corresponding multi-peak candidate matches are used to construct the model polygon. Correspondence is determined based on the local geometric relations between the three feature points and the multi-peak candidates. The disparity test and the global consistency checkout are applied to eliminate the remaining ambiguous matches that are not removed by the local geometric relational test. Experimental results show that the proposed algorithm is feasible and accurate.