Development of Zn(II) sensors based on the assisted transfer of metal ions by hydrophobic ligands through gel-supported microinterfaces

Square-wave voltammetry (SWV) has been used to study the transfer of zinc(II) ion under static conditions, assisted by 5,6-diphenyl-3-(2-pyridyl)-1,2,4-triazine (DPT), through gel-supported microinterfaces. Microhole arrays created by laser photoablation of thin polyester films were used to support an organic gel phase prepared by addition of 1,3?:?2,4-dibenzylidenesorbitol (DBS) to a solution of o-nitrophenyloctyl ether (o-NPOE) with the appropriate supporting electrolyte. The results show that SWV can be used with the gel-supported microinterfaces if a gelified aqueous reference is used for the organic phase. Under such conditions a preliminary estimate of the detection limit for the determination of Zn²⁺ is 5 × 10^–8 mol L^–1.     

Optimisation of the conditions for stripping voltammetric analysis at liquid–liquid interfaces supported at micropore arrays: a computational simulation

Micropore membranes have been used to form arrays of microinterfaces between immiscible electrolyte solutions (μITIES) as a basis for the sensing of non-redox-active ions. Implementation of stripping voltammetry as a sensing method at these arrays of μITIES was applied recently to detect drugs and biomolecules at low concentrations. The present study uses computational simulation to investigate the optimum conditions for stripping voltammetric sensing at the μITIES array. In this scenario, the diffusion of ions in both the aqueous and the organic phases contributes to the sensing response. The influence of the preconcentration time, the micropore aspect ratio, the location of the microinterface within the pore, the ratio of the diffusion coefficients of the analyte ion in the organic and aqueous phases, and the pore wall angle were investigated. The simulations reveal that the accessibility of the microinterfaces during the preconcentration period should not be hampered by a recessed interface and that diffusional transport in the phase where the analyte ions are preconcentrated should be minimized. This will ensure that the ions are accumulated within the micropores close to the interface and thus be readily available for back transfer during the stripping process. On the basis of the results, an optimal combination of the examined parameters is proposed, which together improve the stripping voltammetric signal and provide an improvement in the detection limit.     

Toxicity screening by electrochemical detection of DNA damage by metabolites generated in situ in ultrathin DNA-enzyme films

Rapid detection of DNA damage could serve as a basis for in vitro genotoxicity screening for new organic compounds. Ultrathin films (20-40 nm) containing myoglobin or cytochrome P450(cam) and DNA grown layer-by-layer on electrodes were activated by hydrogen peroxide, and the enzyme in the film generated metabolite styrene oxide from styrene. This styrene oxide reacted with double stranded (ds)-DNA in the same film, mimicking metabolism and DNA damage in human liver. DNA damage was detected by square wave voltammetry (SWV) by using catalytic oxidation with Ru(bpy)(3)(2+) (bpy = 2,2'-bipyridine) and by monitoring the binding of Co(bpy)(3)(3+). Damaged DNA reacts more rapidly than intact ds-DNA with Ru(bpy)(3)(3+), giving SWV peaks at approximately 1 V versus SCE that grow larger with reaction time. Co(bpy)(3)(3+) binds more strongly to intact ds-DNA, and its SWV peaks at 0.04 V decreased as DNA was damaged. Little change in SWV signals was found for incubations of DNA/enzyme films with unreactive organic controls or hydrogen peroxide. Capillary electrophoresis and HPLC-MS suggested the formation of styrene oxide adducts of DNA bases under similar reaction conditions in thin films and in solution. The catalytic SWV method was more sensitive than the Co(bpy)(3)(3+) binding assay, providing multiple measurements over a 5 min reaction time.     

Square‐Wave Voltammetric Transfer of Silver Ions Across the Water|1,2‐Dichloroethane Interface

Recently reported studies on the transfer of silver ions across the aqueous|1,2‐dichloroethane interface using cyclic voltammetry (CV), facilitated by organic phase electrolyte anions, have been augmented by square‐wave voltammetry (SWV) and square‐wave stripping voltammetry (SWSV) studies and by consideration of the possible transfers of additional metal cations. Using SWV and SWSV, detection limits have been improved, from the 0.02 mM obtained by CV, to 1.4 μM (SWV) and 2 nM (SWSV). Additional studies show that mercury(I and II) ions, platinum(II) ions and gold(III) ions are also transferable across this interface, to differing extents. Of these three ions studied, highest sensitivity is achieved for the gold species.     

Three component reactions：An efficient and green synthesis of 3, 4-dihydropyrimidin-2-(1H)-ones and thiones using silica gel-supported L-pyrrolidine-2-carboxylic acid-4-hydrogen sulfate

An environmentally benign aqueous protocol for the synthesis of 3,4-dihydropyrimidin-2-(1H)-ones and thiones promoted by a green catalyst,silica gel-supported L-pyrrolidine-2-carboxylic acid-4-hydrogen sulfate,has been developed.The use of nontoxic,thermally stable and inexpensive amino acid catalyst makes the process simple with minimal amount of chemical waste.Compared with classical Biginelli reaction conditions,this new method has the advantages of high yields and simple workup procedures.     

Ceric ammonium nitrate on silica gel for efficient and selective removal of trityl and silyl groups

Silica gel-supported ceric ammonium nitrate (CAN-SiO2) was found effective for rapid and selective cleavage of trityl (Tr), monomethoxytrityl (MMTr), and dimethoxytrityl (DMTr) groups from protected nucleosides and nucleotides under mild conditions. Efficiency of deprotections depended upon the stability of the resultant carbocationic species: DMTr+ > MMTr+ > Tr+. Use of a catalytic amount of this solid-supported reagent can also efficiently and selectively remove the tert-butyldimethylsilyl or the triisopropylsilyl group from a primary hydroxyl functionality in di- or trisilyl ethers of ribonucleosides. A comparative study of deprotection reactions by utilization of CAN alone or CAN-SiO2 indicates a remarkable increase in the rate of the reactions involving a solid support. The mechanism of electron-transfer processes is proposed for the use of CAN-SiO2 in the removal of these protective groups from organic molecules.     

Voltammetric investigation of Tamsulosin

The electrooxidative behavior and determination of Tamsulosin HCl (TAM), one of the alpha(1)-adrenoceptor antagonist, on a glassy carbon disc electrode were investigated for the first time by using cyclic, linear sweep, differential pulse (DPV) and square wave voltammetry (SWV). TAM showed an irreversible oxidation behavior at all pH values and buffers studied. From the electrochemical response, the main oxidation step was found to be related to the methoxy group on the phenyl ring. DPV and SWV were used to generate peak current versus concentration curves for TAM. A linear response was obtained in the range comprised between 2x10(-6) and 4x10(-4) M for both techniques with detection limit of 3.34x10(-7) M for DPV and 2.45x10(-7) M for SWV. The methods were proposed for the determination of TAM in dosage forms adopting both DPV and SWV modes. The methods were extended to the in vitro determination of TAM in spiked serum samples.     

Thin‐Film Voltammetry of a Lutetium Bisphthalocyanine at Ionic Liquid|Water Interface

At room temperature, tetraoctylphosphonium bromide is a viscous ionic liquid, this gel‐like organic phase can be cast over a basal‐plane graphite electrode (BPGE). Cyclic voltammetry at such a modified electrode, in contact with an aqueous solution have revealed one reversible oxidation and five reversible reduction steps for a Lu^III bisphthalocyanine dissolved in the ionic liquid film, a proof that the highly reactive reduced species were protected from interaction with water in this highly lipophilic phase. It has also been shown that the redox properties are influenced by the ions in the aqueous phase, a property which has been attributed to ion‐pairing effects; obviously, the ion transfers at the organic|aqueous interface has been ignored. Electrochemistry of Lu(III)[(_tBu)₄Pc]₂ (cyclic voltammetry and square wave voltammetry) under similar conditions shows that the nature and concentration of the anion in the aqueous solution in contact with the ionic liquid film influences the potential of the electrode reaction. This can be attributed to variations of the interfacial potential and also because the organic phase is an anion exchanger. Moreover, SWV experiments suggest that the rate of the overall reaction varies with the nature and concentration of the anion of the aqueous electrolyte, which implies that the ion transfer through the organic|aqueous interface is slower than the electron exchange rate of the molecule at the surface of graphite.     

A simultaneous study of kinetics and thermodynamics of anion transfer across the liquid/liquid interface by means of Fourier transformed large-amplitude square-wave voltammetry at three-phase electrode

This paper describes a novel application of Fourier transformed large-amplitude square-wave voltammetry (FT-SWV) in combination with three-phase edge plane pyrolytic graphite (EPPG) electrode to investigate both the kinetics and thermodynamics of anion transfer across the liquid/liquid interface using a conventional three-electrode arrangement. The transfer of anion from aqueous phase to organic phase was electrochemically driven by reversible redox transformation of confined redox probe in the organic phase. The kinetics and thermodynamics of anion transfer were inspected by a so-called "quasi-reversible maximum" (QRM) emerged in the profile of even harmonic components of power spectrum obtained by Fourier transformation (FT) of time-domain total current response and formal potential E(f) of first harmonic voltammogram obtained by application of inverse FT on the power spectrum. Besides, a systematic study of patterns of behavior of a variety of anions at the same concentration and a specific anion at different concentrations on kinetics and thermodynamics and the effect of amplitude ΔE on QRM were also conducted, aiming to optimize the measurement conditions. The investigation mentioned above testified that the ion transfer across the liquid/liquid interface controls the kinetics of overall electrochemical process, regardless of either FT-SWV or traditional SWV investigation. Moreover, either the kinetic probe f(max) or the thermodynamic probe E(f) can be served as a way for analytical applications. Interestingly, a linear relationship between peak currents of the first harmonic components and concentrations of perchlorate anion in the aqueous solutions can be observed, which is somewhat in accordance with a finding obtained by Fourier transformed alternating current voltammetry (FT-ACV) [Bond, A. M.; Duffy, N. W.; Elton, D. M.; Fleming, B. D. Anal. Chem. 2009, 81, 8801-8808]. This may open a new door for analytical detection of a wide spectrum of electrochemically inactive analytes of biological and environmental significance. Compared with traditional SWV, FT-SWV is much simpler and faster in ion transfer kinetics estimation and also provides a new access to thermodynamics evaluation.     

Effect of probiotication on antioxidant and antibacterial activities of pomegranate juices from sour and sweet cultivars

There is an increasing interest in using pomegranate juice as a natural antioxidant rather than synthetic compounds. In this study, the antioxidant capacities of probioticated and nonprobioticated aril juices of sweet (SWV) and sour (SV) pomegranate cultivars were determined by two different methods: ferric reducing antioxidant power (FRAP) and 1,1-diphenyl 2-picrylhydrazyl assay. Total counts of Lactobacillus casei GG increased by about 3 log in SWV and 2 log in SV juices after incubation for 48 h. Probiotication improved the antioxidant activity of SWV juice from 74.4% to 91.82%, and SV juice from 82.64% to 97.8%. Based on the FRAP value, the reducing power of the probioticated pomegranate juices was also much stronger than the nonprobioticated juices. The FRAP values for SWV and SV probioticated juices were 97.34 and 120.7 mmol L(-1), respectively, which were notably higher than 85.87 and 93.4 mmol L(-1) for SWV and SV nonprobioticated juices. Both fermentated and nonfermentated juices exhibited a potent and wide-spectrum antibacterial effect, with the highest activity against Pseudomonas aeruginosa. SV juice showed wider zones of growth inhibition. The results of this study verify for the first time that probiotication of SWV and SV pomegranate juices can add to their beneficial antioxidant activities.     

Determination of trace levels of titanium in polyolefin polymers by catalytic reduction using square wave voltammetry

A sensitive and rapid method for the determination of trace levels of titanium in polyolefin polymers using square wave voltammetry is discussed. It involves ashing, acid digestion of polymer samples and determination of titanium(IV) by catalytic reduction using square wave voltammetric (SWV) technique. A well defined peak of titanium(IV) in Britton-Robinson buffer solution containing EDTA and KBrO(3) is observed in the potential range of -0.10 to -0.40 vs. Ag/AgCl. Calibration graphs were linear in the range 0.05-0.25 microg/ml for titanium. Effects of pH and concentration of bromate, EDTA and buffer constituents are studied for the optimization of experimental conditions. Interference from other concomitants present in the polymer matrix are studied. Low density polyethylene (LDPE) obtained by tubular process was used for preparing the synthetic standards in order to optimize the experimental conditions and good recoveries (99-101%) were obtained. The method was extended to different polyolefin samples and the results obtained for the titanium content compared with those obtained by UV/Vis spectrophotometry. Statistical evaluation showed no significant bias between the two methods. SWV is found suitable for the estimation of Ti in the range 1-50 microg/g in polyolefin polymers with a RSD < 2.0%.     

One-pot synthesis of 2-amino-3-cyano-4-arylsubstituted tetrahydrobenzo[<Emphasis Type="Italic">b</Emphasis>]pyrans catalysed by silica gel-supported polyphosphoric acid (PPA-SiO<Subscript>2</Subscript>) as an efficient and reusable catalyst

A convenient method for the synthesis of tetrahydrobenzo[b]pyrans by a one-pot three-component cyclocondensation of dimedone, aryl aldehydes, and malononitrile in water using silica gel-supported polyphosphoric acid (PPA-SiO₂) as an efficient and reusable catalyst is described. The present methodology offers several advantages, such as a simple procedure with ease of handling, short reaction time, high yields, and the absence of any volatile and hazardous organic solvents.     

Application of a Carbon Paste Electrode Modified with a Schiff Base Ligand to Mercury Speciation in Water

A carbon paste electrode, modified with benzylbisthiosemicarbazone is used for mercury speciation in water samples. Mercury ion is selectively accumulated on the electrode surface at open circuit and its analysis was performed by cyclic voltammetry or square‐wave voltammetry (SWV). A detection limit of 8 μg L^?1 (3σ) was found for 15 min of accumulation using SWV as measurement technique. The effect of several metallic ions and organic substances on voltammetric signal is examined. For speciation purposes, a ligand competition methodology between ligands in solution and electrode is used. Model mercury complexes are characterized as a function of their dissociation kinetics. The method was applied to mercury speciation in water samples from the Jarama River in Madrid.     

Electrochemical behavior of thiamine on a self-assembled gold electrode and its square-wave voltammetric determination in pharmaceutical preparations.

The electrochemical behavior of thiamine on a self-assembled electrode of L-cysteine (Cys/SAM/Au) has been investigated and Cys/SAM/Au can be used to detect thiamine using square-wave voltammetry (SWV). At pH 11.40 Britton-Robinson buffer, thiamine exhibits a well-defined anodic peak on Cys/SAM/Au. Under the optimized conditions, the anodic peak current of SWV was linear with the content of thiamine in the range of 1.1 x 10(-8) - 2.2 x 10(-6) mol/L; the detection limit was 5.5 x 10(-9) mol/L. The method was successfully applied to the determination of thiamine in pharmaceutical preparations.     

Controlling the Bonding Site of Photosynthetic Reaction Centers on Au Electrode by Different Bifunctional Agents

The orientation of the immobilized protein is the key factor to effect the surface electrochemistry of the redox couples therein. The photosynthetic reaction centers (RCs) composite film was fabricated by self-assembled monolayers (SAMs) on Au electrode. The bifunctional reagents e.g. 4-aminothiophenol (ATP), 2-mercaptoehtylamine (MEA), 2-mercaptoethanol (ME), 2-mercaptoacetic acid (MAA), and Poly(dimethyldiallylammonium) chloride(PDDA) were found to bond RCs at different sites. The square wave voltammetry (SWV), bulk electrolysis were employed for characterizing the composite film. The electrochemically-driven electron transfer (ET) behavior in films was found driven by SWV or bulk electrolysis. In case the electrode was modified directly by amino compound reagent, the greater force was needed. If the film was activated by SWV with frequency of 15 Hz, the SWV amplitude of about lOOmV for MAA-PDDA-RC and 250 mV or more for MA-RC film was needed respectively. When the ME-PDDA-RC composite film was stimulated by SWV, the peak for the bacteriochlorophyll dimmer (P) and secondary quinone (Q_B) appeared at first, then the peak of primary quinone (Q_A) came into being. Further more,if the simulated signal of SWV was continually applied, all of the peak current increased. On the other hand, the opposite process was observed while the potential of -0.4 V was applied by bulk electrolysis. For all the composite films,the redox potential for P⁺/P declined with frequency increasing from 30 to 150 Hz.As reported before, the redox potential of species in RC were:0.45-0.60 V (vs.NHE)for P⁺/p, +0.05~-0.15 V for Q_A and -0.20~-0.35 V for Q_B.     

Bioelectrochemical Magnetic Immunosensing of Trichloropyridinol: A Potential Insecticide Biomarker

A fast, simple and sensitive bioelectrochemical magnetic immunosensing method is developed to monitor a potential insecticide biomarker, trichloropyridinol (TCP), in environmental sample. A magnet/glassy carbon (MGC) working electrode was used to accumulate immunocomplex associated magnetic beads and separate free and unbound reagents after liquid phase competitive immunoreaction among TCP antibody coated magnetic beads, TCP analyte and horseradish peroxidase (HRP) labeled TCP. The activity of HRP tracers was monitored by square‐wave voltammetry (SWV) by scanning electrocactive enzymatic product in the presence of 3,3′,5,5′‐tetramethylbenzidine dihydrochloride and hydrogen peroxide (TMB‐H₂O₂) substrate solution. The electrochemical signal of enzymatic product was greatly enhanced by dual accumulation events: magnetic accumulation of enzyme tracers bound magnetic beads and constant potential accumulation of enzymatic product. The voltammetric characteristics of substrate and enzymatic product were investigated, and the parameters of SWV analysis and immunoassay were optimized. Under the optimal conditions the immunosensor was used to measure as low as 5 ng L^?1 (ppt) TCP, which is 50‐fold lower than the value indicated by the manufacture of the TCP RaPID Assay kit (0.25 μg/L, colorimetric detection). The performance of the developed immunosensing system was successfully evaluated with river water samples spiked with TCP, indicating this convenient and sensitive technique offers great promise for decentralized environmental application. This technique could be readily used for detection of other environmental contaminants by developing specific antibodies against the contaminants and are expected to open new opportunities for environmental monitoring and public health.     

Detection of haemoglobin using an adsorption approach at a liquid–liquid microinterface array

The behaviour of haemoglobin (Hb) at the interface between two immiscible electrolyte solutions (ITIES) has been examined for analytical purposes. When Hb is fully protonated under acidic conditions (pH <pI) in the aqueous phase, it undergoes a potential-dependent adsorption and complexation, at the interface, with the anions of the organic phase electrolyte. When utilised as a simple and fast preconcentration step, consisting of adsorbing the protein at the interface, in conjunction with voltammetric desorption, this opens up the ITIES to the adsorptive stripping voltammetry approach. Utilising a 60 s adsorption step and linear sweep voltammetry, a linear response to Hb concentration in aqueous solution over the range 0.01–0.5 μM was achieved. The equation of the best-fit straight line was I _p ? =?7.46 C???0.109, R?=?0.996, where I _p is the peak current (in nanoampere) and C is haemoglobin concentration (in micromolar). The calculated detection limit (3σ) was 48 nM for a 60 s preconcentration period, while the relative standard deviation was 13.3 % for six successive measurements at 0.1 μM Hb. These results illustrate the prospects for simple, portable and rapid label-free detection of biomacromolecules offered by electrochemistry at arrays of liquid–liquid microinterfaces.     

用对氨基苯酚改性的碳纳米管糊电极同时测定羟胺和苯酚(英文)

A carbon paste electrode that was chemically modified with multiwall carbon nanotubes and p-aminophenol was used as a selective electrochemical sensor for the simultaneous detection of hydroxylamine (HX) and phenol. Cyclic voltammetry, double potential-step chronoamperometry, square wave voltammetry (SWV), and electrochemical impedance spectroscopy were used to investigate the use of p-aminophenol in the carbon nanotubes paste matrixes as a mediator for the electrocatalytic oxidation of HX and phenol in aqueous solution. The coefficient of electron transfer and catalytic reaction rate constant were determined using the electrochemical methods. Under optimized conditions, the electrocatalytic oxidation current peaks for HX and phenol increased linearly with concentration in the range of 0.5-180.0 and 10.0-650.0 μmol/L for HX and phenol, respectively. The detection limits for HX and phenol were 0.15 and 7.1 μmol/L, respectively. The anodic potential peaks of HX and phenol were separated by 0.65 V in SWV. Because of good selectivity and sensitivity, the present method provides a simple method for the selective detection of HX and phenol in practical samples such as water samples.     

Silica gel-supported bis-cinchona alkaloid: a chiral catalyst for the heterogeneous asymmetric desymmetrization of meso-cyclic anhydrides

A one-pot conversion of meso-cyclic anhydrides with alcoholysis in diethyl ether using SGS-(DHQ)₂AQN 4, a silica gel-supported chiral catalyst, into the corresponding desymmetrized mono ester acids was achieved with enantiomeric excesses of up to 84% under mild and efficient conditions.     

Electroanalysis of the Anthelmintic Drug Bithionol at Edge Plane Pyrolytic Graphite Electrode

An electrochemical study of the anthelmintic drug bithionol using edge plane pyrolytic graphite electrode (EPPGE) is presented for the first time by applying different electrochemical techniques, such as cyclic voltammetry (CV), square‐wave voltammetry (SWV), square‐wave adsorptive stripping voltammetry (SWAdSV), and alternating current (AC) impedance spectroscopy. Mechanistic aspects of the electrode reaction were studied implying a quasireversible electrode reaction from an adsorbed state of the reactant, coupled with a follow‐up chemical reaction to a final electroinactive product. The overall mechanism appears totally irreversible under conditions of CV at moderate scan rate, while being quasireversible under conditions of the fast SWV. Furthermore, an optimisation of the analytical procedure for quantitative determination of bithionol was conducted by applying SWV in an adsorptive stripping mode. The calibration curve was constructed in the concentration range of 0.1–1.0 μmol L^?1 (R²=0.9984) with a sensitivity of 3.6 μA L μmol^?1 and LOD of 26.7 nmol L^?1. The simple and sensitive SWAdSV procedure was proved to be suitable for the analysis of spiked urine samples.