消能锥阀结构改进的三维数值模拟研究

对常规消能锥阀体型进行了改进,提出了一种新型的嵌套式消能锥阀.该新阀将原来通过阀体的一股环状射流变为两股互不平行的环状射流,通过这两股高速水流在阀口的碰撞提高消能率、改善流态.采用可压缩的两相流模型,辅以Realizable k–ε湍流模型来模拟锥阀附近水流的水力特性,对于自由水面的处理采用了VOF法,并进行压强场和流速场及消能情况的对比分析.结果显示:在上游进口端控制断面的水流流量相同的情况下使用嵌套式消能锥阀,阀前进水管道的压强可由原来的25kPa减小到15kPa,减小了40%;阀体所承受的压力由35kPa减小到10kPa,减小了57%;下游管道中水流落点之后的沿程断面平均流速减小了约0.1m/s.在上游进口端具有相同的总水头的情况下,嵌套式消能锥阀对流速水头及压强水头的消能能力都要比使用常规消能锥阀好.     

基于转捩/尺度适应模型与FW-H声学方程的气动噪声数值模拟研究

采用计算流体力学(CFD)同"声类比"相结合的方法进行噪声模拟,利用CFD数值模拟 MD30P30N多段翼型失速攻角附近流场以及其气动特性来校核近场精度,进一步通过结合可穿透数据面的FW-H声学方程进行气动噪声分析。为了准确捕捉近场流场信息,为噪声预测提供可靠的声源精度,本文基于k-ω剪应力输运(SST)湍流模型,建立了尺度适应分离流(SAS)模型,并采用γ-Re_θt转捩模型耦合k-ω SST湍流模型建立了边界层转捩数值模拟技术;充分利用尺度适应模型在边界层表现为雷诺平均(RANS)方法这一特点,将γ-Re_θt转捩模型与SAS模型结合,建立针对包含转捩、分离现象复杂流场的数值模拟技术。文中以RANS为控制方程,分别采用全湍流k-ω SST模型、γ-Re_θtSAS转捩/分离流模型对多段翼进行近场数值模拟计算,结合可穿透数据面的FW-H声学方程进行气动噪声预测,在分析其对流场及气动噪声影响的基础上,得出了几点结论。     

亚临界雷诺数下圆柱受迫振动的数值研究

在Navier-Stokes方程和k-ω湍流模型的基础上,利用流线迎风有限元方法结合ALE动网格技术对亚临界雷诺数下的圆柱受迫振动问题开展了数值模拟研究。本文的数值模型成功模拟了Re=5000条件下,圆柱发生受迫振动时尾迹区内的2S,2P和P+S尾流模式;对Re=10000情况下,无量纲振幅分别为0.3,0.4,0.5的圆柱受迫振动问题开展了数值模拟,分析了给定振幅条件下圆柱受力随振动频率的变化关系以及受迫振动的锁定区间。以上数值计算结果与Gopalkrishnan (1993)的实验结果基本符合。研究结果表明,二维数值模型能够基本正确地反映出圆柱发生受迫振动时的涡激振动特性以及有关的受力变化趋势,为今后进一步开展三维数值分析工作奠定了基础。     

内锥流量计流出系数预测方法研究

采用标准k-ε模型、RNG(Renormalization Group)k-ε模型、Realizable k-ε模型和Reynolds应力方程模型 RSM(Reynolds Stress Model) 对100 mm口径6种结构的内锥流量计内流场进行了数值模拟.在等效直径比β值为0.65的三种结构内锥流量计流出系数的仿真计算中,四种湍流模型计算结果与物理实验结果误差的平均值分别为4.19%,2.84%,2.88%和-0.822%;对β值为0.85的情况,各模型计算误差的平均值分别为11.8%,9.62%,9.30%和4.76%.研究结果表明,RSM模型在6种结构内锥流量计流出系数的预测中,计算精度较高,表现出了较好的性能,优于三种k-ε涡粘模型,更适于内锥流量计流场数值模拟与流出系数的预测.     

浮式海上风力机叶片气动性能的流固耦合分析

随着深水浮式海上风电场在世界范围内的兴起,浮式平台运动性能对风力机稳定运行及叶片气动载荷影响的研究具有重要意义。基于三维粘性不可压缩Navier-Stokes方程和适用于旋转流场分析的重整化群k-ε（RNG）湍流模型,数值模拟美国可再生能源实验室（NREL）5MW海上风力机的气动性能,并将数值模拟结果与NREL的设计参考数据进行对比分析,较好地验证了该数值模拟方法的有效性。进一步利用滑移网格技术模拟风力机叶片随浮式平台的典型周期性运动,实现浮式风力机叶片与周围流场的复杂非线性流固耦合分析,分别研究浮式平台不同运动幅值和运动周期对风力机叶片气动性能的影响规律,并从物理机理角度进行阐明分析。本文的主要研究成果,将对未来大型深水浮式海上风力机的气动性能分析及浮式平台系统的运动性能设计起到积极的指导作用。     

煤液化高压差调节阀空蚀/冲蚀磨损预测

针对煤液化示范工程中高压差调节阀高速气-液-粒三相流传输引起的阀芯严重空蚀和冲蚀磨损问题,采用k-ε湍流模型、Schnerr-Saur空化模型、随机轨道模型和冲蚀磨损模型,计算了典型开度下的速度、压力、相分率和磨损率等参数.计算结果表明:阀芯头部圆弧段下游附近有空化区,其顶部附近存在高速回流且压力高于介质的饱和蒸气压,综合分析空化区、回流区和壁面压力可预测空蚀主要发生在阀芯顶部;阀芯的最大冲蚀磨损率发生在顶部,且随开度减小而加剧.并结合调节阀实际损伤形貌,验证了空蚀预测方法及冲蚀磨损计算的正确性.本研究有望为多相介质传输设备的优化设计提供参考.     

代数多重网格方法在紊流数值预测中的应用

机械和矿山工程中广泛使用锥形渐扩管。将DLR型k-ε紊流模型中非线性偏微分方程基于全隐式高精度迎风差分格式离散,得到差分方程的系数矩阵为五对角块十三对角带状稀疏矩阵,基于一种"三元组"方式进行压缩存储,节约内存。提出了一种基于DLR型k-ε紊流模型与代数多重网格方法结合的新算法,阐述了代数多重网格方法的实施过程。对具有逆压梯度流动的锥形渐扩管内紊流进行了数值预测。数值实验表明,代数多重网格方法对求解紊流模型离散方程组非常有效,同此前该紊流数值模拟中使用的Point-SOR方法相比,计算效率有了显著提高,计算结果与实验结果吻合较好。     

大涡模拟及其在湍流燃烧中的应用

大涡模拟作为一种研究湍流流动和湍流燃烧的有效手段,在国际上已经得到广泛应用。本文在回顾了大涡模拟(LES)的基本思想及其实施方法的基础上着重介绍了前人在大涡模拟的亚格子湍流模式和亚格子燃烧模式中的研究成果,同时给出了采用不同亚格子模式的大涡模拟在湍流燃烧中的应用实例,指出了大涡模拟在湍流燃烧中的重要作用,为大涡模拟的进一步发展和应用提供参考。      

锥体效应对超音速湍流边界层统计特性的影响

通过直接数值模拟,计算了空间模式下,来流马赫数为2.5, 半锥角为$5^{\circ}$, 零攻角的绝热钝锥湍流边界层,研究了湍流的统计特性,并把结果与超音速平板湍流边界层和马赫数为6的高超音速钝锥湍流边界层的结果进行了比较,重点定量地考察了锥体效应对边界层湍流统计特性的影响. 研究发现,锥体效应对平均温度剖面以及压缩性的影响是显著的;而其它统计量,比如速度壁面律、雷诺应力的分布和湍动能各项的贡献等,受锥体效应的影响很小.      

基于DES方法平底水力旋流器内部流场特征的数值分析

采用分离涡模拟方法(Detached Eddy Simulation,DES)针对平底水力旋流器的特殊结构进行了清水流场三维湍流流动的数值模拟.与RNG k-ε模型、雷诺应力模型的计算结果比较后发现,DES方法所预测出的切向速度结果与实验结果吻合最好,从而验证了DES方法在水力旋流器数值模拟方面的可行性.进一步分析了在一定入口流量下平底水力旋流器内部流场的切向速度、轴向速度、径向速度及静压力的分布特征以及局部流动现象,获得了有关平底水力旋流器内流场流动结构的丰富的信息,讨论了圆柱结构内的流动特征对固液分离可能存在的影响.分析表明平底水力旋流器的内流场呈现出兰金涡的特点,并且为非对称分布,其内部的能量损耗主要集中在受强制涡影响的中心轴线附近区域内.本文结果为进一步研究平底水力旋流器的流场特征提供了参考.     

The 7th International Conference on Fluid Mechanics May 24-27,2015,Qingdao,China

正http://www.icfm7.org First Announcement and Call for PapersThe objective of International Conference on Fluid Mechanics(ICFM)is to provide a forum for researchers to exchange new ideas and recent advances in the fields of theoretical,experimental,computational Fluid Mechanics as well as interdisciplinary subjects.It was successfully convened by the Chinese Society of Theoretical and Applied Mechanics(CSTAM)in Beijing(1987,     

INFORMATION FOR CONTRIBUTORS

Contributions： The Journal, Acta Mechanica Solida Sinica, is pleased to receive papers from engineers and scientists working in various aspects of solid mechanics. All contributions are subject to critical review prior to acceptance and publication.     

基于鲁棒滤波的捷联导引头视线角速度估计方法

针对捷联导引头无法直接获取视线角速度等信息的问题,研究了鲁棒滤波在大气层外飞行器捷联导引头视线角速度估计中的应用。为了建立非线性滤波估计模型,考虑目标视线角速度的慢变特性,采用一阶马尔科夫模型建立了状态方程;推导了视线角速度的解耦模型,并建立了量测方程;考虑到实际应用中存在系统噪声统计特性失准的问题,基于Huber-Based鲁棒滤波方法,设计了视线角速度滤波器,并完成了基于Huber-Based滤波方法和扩展卡尔曼滤波方法的数学仿真。仿真结果表明Huber-Based滤波方法的视线角、视线角速度及视线角加速度估计精度分别达到0.1140'、0.1423'/s、0.0203'/s2,而扩展卡尔曼滤波方法的视线角、视线角速度及视线角加速度估计精度仅分别为0.6577'、0.6415'/s、0.0979'/s~2。仿真结果证明了该方法可以有效地估计出相对视线角速度等信息,并且在非高斯噪声的条件下,依然可获得较高的估计精度,具有一定的鲁棒性。     

Guide for authors

正Each of the sections below provides essential information for authors.We recommend that you take the time to read them before submitting a contribution to Acta Mechanica Sinica.We hope our guide to authors may help you navigate to the appropriate section.How to prepare a submission This document provides an outline of the editorial process involved in publishing a scientific paper in Acta Mechanica     

Use specification of multiscale materials for life spanned over macro-, micro-, nano-, and pico-scale

Multiscale material intends to enhance the strength and life of mechanical systems by matching the transmitted spatiotemporal energy distribution to the constituents at the different scale, say—macro, micro, nano, and pico,—, depending on the needs. Lower scale entities are, particularly, critical to small size systems. Large structures are less sensitive to microscopic effects. Scale shifting laws will be developed for relating test data from nano-, micro-, and macro-specimens. The benefit of reinforcement at the lower scale constituents needs to be justified at the macroscopic scale. Filling the void and space in regions of high energy density is considered.Material inhomogeneity interacts with specimen size. Their combined effect is non-equilibrium. Energy exchange between the environment and specimen becomes increasingly more significant as the specimen size is reduced. Perturbation of the operational conditions can further aggravate the situation. Scale transitional functions and/or f_j/j+1 are introduced to quantify these characteristics. They are represented, respectively, by , and (f_mi/ma,f_na/mi,f_pi/na). The abbreviations pi, na, mi, and ma refer to pico, nano, micro and macro.Local damage is assumed to initiate at a small scale, grows to a larger scale, and terminate at an even larger scale. The mechanism of energy absorption and dissipation will be introduced to develop a consistent book keeping system. Compaction of mass density for constituents of size 10⁻¹², 10⁻⁹, 10⁻⁶, 10⁻³ m, will be considered. Energy dissipation at all scales must be accounted for. Dissipations at the smaller scale must not only be included but they must abide by the same physical and mathematical interpretation, in order to avoid inconsistencies when making connections with those at the larger scale where dissipations are eminent.Three fundamental Problems I, II, and III are stated. They correspond to the commonly used service conditions. Reference is made to a Representative Tip (RT), the location where energy absorption and dissipation takes place. The RT can be a crack tip or a particle. At the larger size scales, RT can refer to a region. Scale shifting of results from the very small to the very large is needed to identify the benefit of using multiscale materials.     

Impact non-pénétrant sur le thorax : influence de la courbure sur la propagation des ondesNonpenetrating impact on the thorax: influence of curvature on wave propagation

Theoretical studies of the propagation of impact waves through the thorax are needed to improve the design of bulletproof jackets and blast protections (Fung in ‘Biomechanics Motions, Flow, Stress, and Growth’, Springer-Verlag, 1990; Cooper et al., J. Trauma 40 (1996) S38–S41). The influence of the weak acoustic coupling at the interface between the thoracic wall and the lung were described in (Grimal et al., C. R. Acad. Sci. IIB 329 (2001) 655–662); in this work, we study, within the frame of elastodynamics and with an approximate analytical method, the effects of the curvature of this interface. Results are given in terms of strain energy for the pressure wave, transmitted or converted. Focalisation of energy in the medium representing the lung is important for curvatures measured in humans. To cite this article: Q. Grimal et al., C. R. Mecanique 330 (2002) 569–574.     

Vérification expérimentale de la relation de réciprocité d'Onsager pour l'électro-osmose et l'électro-filtration dans une argile naturelleExperimental verification of the Onsager's reciprocal relations for electro-osmosis and electro-filtration phenomena on a saturated clay

This Note is devoted to the experimental verification of the Onsager's reciprocal relations in the particular case of electro-osmosis and electro-filtration. A special set up has been designed to carry out the measurements of both the electro-osmotic permeability and the streaming potential. This has been performed by using a natural material i.e., saturated kaolinite. To cite this article: K. Beddiar et al., C. R. Mecanique 330 (2002) 893–898.