Fabrication and characterization of P(VDF-HFP)/SBA-15 composite membranes for Li-ion batteries

This study reports on the preparation of a composite polymer electrolyte for secondary lithium-ion battery. Poly(vinylidiene fluoride-hexafluoropropylene) (P(VDF-HFP)) was used as the polymer host, and mesoporous SBA-15 (silica) ceramic fillers used as the solid plasticizer were added into the polymer matrix. The SBA-15 fillers with mesoporous structure and high specific surface can trap more liquid electrolytes to enhance the ionic conductivity. The ionic conductivity of P(VDF-HFP)/SBA-15 composite polymer electrolytes was in the order of 10⁻³ S cm⁻¹ at room temperature. The characteristic properties of the composite polymer membranes were examined by using FTIR spectroscopies, scanning electron microscopy (SEM), and an AC impedance method. For comparison, the LiFePO₄/Li composite batteries with a conventional microporous polyethylene (PE) separator and pure P(VDF-HFP) polymer membrane were also prepared and studied. As a result, the LiFePO₄/Li composite battery comprised the P(VDF-HFP)/10 wt.% m-SBA-15 composite polymer electrolyte, which achieves an optimal discharge capacity of 88 mAh g⁻¹ at 20 C rate with a high coulomb efficiency of 95%. It is demonstrated that the P(VDF-HFP)/m-SBA-15 composite membrane exhibits as a good candidate for application to LiFePO₄ polymer batteries.     

Organo-modified mesoporous silica for sorption of carbon dioxide

Abstract  

Organo-modified mesoporous silica SBA-15 has been studied for sorption of carbon dioxide (CO₂). The SBA-15 sample was functionalized with a branched chain polymer, polyethylenimine (PEI), of different molecular weights (1,300 and 2,000 g mol⁻¹). Surface modification was carried out by impregnation of silica by PEI or by grafting with (3-chloropropyl)triethoxysilane, followed by substitution of chlorine atoms by PEI ligands. The prepared modified mesoporous materials were characterized by nitrogen adsorption/desorption at 77 K, high-resolution transmission electron microscopy, small-angle X-ray scattering, and thermal methods. Sorption of CO₂ was studied by gravimetric method at 303 K. The total amount of sorbed CO₂ varied between 0.19–0.67 mmol/g for respective samples. Regeneration of the materials after adsorption was achieved by thermal treatment at 343 K.     

Encapsulation hemoglobin in ordered mesoporous silicas: Influence factors for immobilization and bioelectrochemistry

The encapsulation of hemoglobin (Hb) on the mesoporous silicas SBA-15 and Au-doped SBA-15 (Au-SBA-15) has been studied as a model protein adsorption system. The influences of solution pH, structure of mesoporous silicas and gold nanoparticles incorporation on Hb immobilization are investigated in detail. The spectral characteristics of Hb/SBA-15 and Hb/Au-SBA-15 nanoconjugate show an absorption curve quite similar to that of native Hb, indicating that Hb retains its higher-order structure in the mesopores of SBA-15. Direct electrochemistry of Hb is obtained when Hb is adsorpted by mesoporous silicas SBA-15 or Au-SBA-15. Moreover, Hb/Au-SBA-15 exerts enhancing electron transfer ability because of the Au incorporation. Additionally, the Hb/Au-SBA-15 displays good electrocatalytic reduction of hydrogen peroxide with a detection limit of 1.0 μM, about 3 times as low as that for the Hb/SBA-15. The Hb/Au-SBA-15 exhibits higher peroxidase-like activity with the apparent Michaelis–Menton constant (K_m) of 2.87 mM, significantly lower than the 7.78 mM value for the Hb/SBA-15.     

Investigation of Mg modified mesoporous silicas and their CO2 adsorption capacities

CO₂ adsorption properties on Mg modified silica mesoporous materials were investigated. By using the methods of co-condensation, dispersion and ion-exchange, Mg²⁺ was introduced into SBA-15 and MCM-41, and transformed into MgO in the calcination process. The basic MgO can provide active sites to enhance the acidic CO₂ adsorption capacity. To improve the amount and the dispersion state of the loading MgO, the optimized modification conditions were also investigated. The XRD and TEM characteristic results, as well as the CO₂ adsorption performance showed that the CO₂ adsorption capacity not only depended on the pore structures of MCM-41 and SBA-15, but also on the improvement of the dispersion state of MgO by modification. Among various Mg modified silica mesoporous materials, the CO₂ adsorption capacity increased from 0.42 mmol g⁻¹ of pure silica SBA-15 to 1.35 mmol g⁻¹ of Mg–Al–SBA-15-I1 by the ion-exchange method enhanced with Al³⁺ synergism. Moreover, it also increased from 0.67 mmol g⁻¹ of pure silica MCM-41 to 1.32 mmol g⁻¹ of Mg–EDA–MCM-41-D10 by the dispersion method enhanced with the incorporation of ethane diamine. The stability test by 10 CO₂ adsorption/desorption cycles showed Mg–urea–MCM-41-D10 possessed quite good recyclability.     

[Cu(bpdo)2·2H2O]2+-supported SBA-15 nanocatalyst for efficient one-pot synthesis of benzoxanthenone and benzochromene derivatives

A novel [Cu(bpdo)₂·2H₂O]²⁺-supported SBA-15 catalyst (bpdo = 2,2′-bipyridine,1,1′-dioxide) was prepared by the impregnation method. The catalyst was characterized by XRD, TEM, and BET nitrogen adsorption–desorption method, FT-IR, UV–vis, and chemical analysis. XRD patterns and TEM analysis of [Cu(bpdo)₂·2H₂O]²⁺/SBA-15 showed highly ordered hexagonal mesoporous silica, even after immobilization. Also, nitrogen adsorption–desorption isotherms exhibited type-IV isotherms and H1 hysteresis loops according to the IUPAC classification of mesoporous materials. This green support was tested for the synthesis of benzoxanthenone and benzochromene derivatives under solvent-free conditions, with high yield of products via a simple experimental and work-up procedure.     

Mesoporous materials incorporating a zinc(II) complex: Synthesis and direct luminescence quantum yield determination

New luminescent inorganic–organic hybrid materials incorporating the luminescent zinc(II) complex ZnL₂ (λ_em = 457 nm and Φ_em = 4.4% reference values for ZnL₂; HL = chelating ligand resulting from the reaction between salicylaldehyde and 3-aminopropyltriethoxysilane), covalently bonded to different types of mesoporous silica hosts (namely MCM-41, MCM-48 and SBA-15), were prepared via both the methods of grafting post-synthesis (GPS) and one-pot synthesis (OPS). The products obtained, which form the GPS [(GPS)(Zn/MCM-41), (GPS)(Zn/MCM-48), (GPS)(Zn/SBA-15)] and the OPS [(OPS)(Zn/MCM-41), (OPS)(Zn/MCM-48), (OPS)(Zn/SBA-15)] series, contain the ZnL₂ guest covalently bonded to the silica framework through silicon–oxygen bonds formed when the silane group is placed at the periphery of the Zn(II) coordination sphere. GPS and OPS materials were characterized by powder X-ray diffraction, N₂ adsorption/desorption, thermogravimetric analysis (TGA) and UV/vis spectroscopy. For the new mesoporous materials the emission quantum yield (EQY) was measured by means of an integrating sphere combined with a spectrofluorimeter. The ZnL₂ loading (measured by the ZnL₂/SiO₂ ratio calculated from TGA data) for MCM-41 appears to be independent of the synthesis procedure, whereas, for both MCM-48 and SBA-15, the ZnL₂/SiO₂ ratio of the materials obtained via OPS is about four times higher than products obtained from GPS. The ZnL₂ loaded GPS and OPS series show λ_em maxima at about 485 and 455 nm, respectively. Moreover, with reference to EQY (GPS)(Zn/SBA-15) and (OPS)(Zn/SBA-15), although featuring ZnL₂/SiO₂ ratios of 0.13 and 0.45, respectively, they showed similar EQY values: 2% and 5%. On the contrary, (GPS)(Zn/MCM-41) and (OPS)(Zn/MCM-41) which give similar ZnL₂/SiO₂ ratios (0.09 and 0.14) exhibit very different EQY, i.e. 2% and 22%, respectively.     

Room temperature synthesis of Ti-SBA-15 from silatrane and titanium-glycolate and its catalytic performance towards styrene epoxidation

A novel room temperature sol–gel synthesis of Ti-SBA-15 is described using moisture stable silatrane and titanium glycolate precursors, and poly(ethylene oxide)-poly(propylene oxide)-poly(ethylene oxide) block copolymer (EO₂₀PO₇₀EO₂₀) as the structure directing agent. Catalyst performance was optimized by systematically investigating the influence of acidity, reaction time and temperature, and titanium loading. Small angle X-ray scattering (SAXS) and transmission electron microscopy (TEM) showed well-ordered 2D mesoporous hexagonal structures, while N₂ adsorption/desorption measurements yielded high surface areas (up to 670 m²/g), with large pore diameters (5.79 nm) and volumes (0.83 cm³/g). Diffuse reflectance UV–visible spectroscopy (DRUV) was found that tetravalent titanium as Ti⁴⁺O₄ tetrahedra were incorporated in the framework through displacement of Si⁴⁺O₄ after calcination (550°C/6 h) to loadings of 7 mol% Ti without perturbation of the ordered mesoporous structure, or decoration by extra-framework anatase containing Ti⁴⁺O₆ octahedra. The catalytic activity and selectivity of styrene epoxidation using hydrogen peroxide (H₂O₂) showed that the conversion of styrene increases significantly at higher titanium contents. The only products of this reaction were styrene oxide and benzaldehyde, with selectivity of 34.2 and 65.8%, respectively, at a styrene conversion of 25.8% over the 7 mol% Ti-SBA-15 catalyst. Beyond this titanium loading, anatase is deposited on the framework and catalytic activity degrades. The performance of the new catalyst is also shown to be superior to conventional materials produced by incipient wetness impregnation where Ti resides on the surface of SBA-15, giving a styrene conversion of 11.9% under identical reaction conditions.     

Amplified spontaneous emission from an infrared dye doped zirconia-organically modified silicate thin film waveguides

Near infrared dye, IR26, was doped into zirconia-organically modified silicate (ORMOSILs) waveguides by sol–gel technique. Amplified spontaneous emission (ASE) centered at 1.14 μm was observed from the solid films and their spectroscopic characteristics were studied. The dependence of ASE on the preparation details was discussed. The threshold and full widths at half maximum (FWHM) of ASE were 8.6 mJ/cm² and ∼15 nm, respectively. The output intensity dropped to 50% of its initial value after 1,200 pulses at a repetition rate of 10 Hz and pump intensity of higher than 50 mJ/cm². These materials are promising for the distributed feedback (DFB) lasers tunable in infrared.     

Preparation, Characterization and Catalytic Performance of La-SO4/SBA-15 in Esterification of Acetic Acid with n-Butanol

La-SO42-/SBA-15 was synthesized with various amounts of lanthanum via incipient-wetness impregnation. Characterization was done by X-ray diffraction（XRD）, transmission electron micrographs（TEM）, nitrogen adsorption, FTIR spectroscopic analysis, thermogravimetric analysis, and the total amount of acidity of catalyst was estimated by TPD of NH3. The results indicate that lanthanum has been incorporated into SBA-15 molecular sieve. The prepared materials（La-SO42-/SBA-15） keep the highly ordered mesoporous two-dimensional hexagonal structure and do not change the mesoporous channel structure of the support SBA-15. The catalyst showed best catalytic activity in the synthesis of n-butyl acetate. The optimum conditions of the esterification by orthogonal experiments were studied： the molar ratio of n-butanol to acetic acid 1：1.2, the amount of catalyst 7.5%, reaction time 80 min. The yield of n-butyl acetate could reach 93.2% under the optimum conditions. The catalyst was recyclable, cost effective and environmental friendly.     

Thermal stability of high surface area silicon carbide materials

The synthesis of mesoporous silicon carbide by chemical vapor infiltration of dimethyl dichlorosilane into mesoporous silica SBA-15 and subsequent dissolution of the silica matrix with HF was investigated. The influence of the synthesis parameters of the composite material (SiC/SBA-15) on the final product (mesoporous SiC) was determined. Depending on the preparation conditions, materials with specific surface areas from 410 to 830 m² g⁻¹ and pore sizes between 2 and 10 nm with high mesopore volume (0.31-0.96 cm³ g⁻¹) were prepared. Additionally, the thermal stability of mesoporous silicon carbide at 1573 K in an inert atmosphere (argon) was investigated, and compared to that of SBA-15 and ordered mesoporous carbon (CMK-1). Mesoporous SiC has a much higher thermal textural stability as compared to SBA-15, but a lower stability than ordered mesoporous carbon CMK-1.     

Synthesis and characterization of P4VP/SBA-15 composite by in situ polymerization

Abstract  

Poly(4-vinylpyridine)/SBA-15 (P4VP/SBA-15) composites with various amounts of SBA-15 were prepared and characterized. The physical and chemical properties of P4VP/SBA-15 were investigated by XRD, BET, FT-IR, TGA, and SEM techniques. The catalytic performance of each material was determined for the Knoevenagel condensation reaction between carbonyl compounds and ethyl cyanoacetate in the presence of water as a solvent. The effects of reaction temperature, the amount of catalyst, amount of support, solvent, and the amount of benzoyl peroxide during the synthesis of P4VP/SBA-15 were investigated, as well as the recyclability of the heterogeneous composite. The catalyst used for this synthetically useful transformation showed a considerable level of reusability as well as very good activity. This reaction occurred rapidly when water was used as a solvent, so we assume it to be a green reaction.     

In-situ oxidation of block copolymer for producing copper oxalate or copper oxide nanowires in mesoporous channels

Copper oxalate nanowires inside the channels of mesoporous SBA-15 are created by in-situ oxidation of block copolymer in as-prepared SBA-15 samples. The pyrolysis of CuC₂O₄/SBA-15 composites under different conditions results in the formation of CuO or Cu₂O nanowires encapsulated in the nanoscale channels. The appearance, structure and composition of these materials are characterized by the X-ray power diffraction, transmission electron microscopy, N₂ adsorption-desorption isotherms, infrared spectra and inductive coupled plasma emission spectra. CuC₂O₄, CuO and Cu₂O nanomaterials filled in the channels of SBA-15 have been proven to possess the electrochemical hydrogen storage capacities of 102, 165 and 231 mAh/g in the second cycle, respectively, and are expected to have a high potential for use in practical applications.     

Mesoporous SBA-15 materials modified with PW or W active species as catalysts for the epoxidation of olefins with H<Subscript>2</Subscript>O<Subscript>2</Subscript>

Five catalysts containing PW or W active species that anchored onto aminosilylated mesoporous silica SBA-15 by a post-grafting route were prepared and the resulting PW or W/APTES/SBA-15 hybrid materials were characterized by XRD, N₂ adsorption/desorption, surface area analysis, TEM, FT-IR, and ICP (inductively coupled plasma atomic emission spectroscopy). The names of these catalysts have been abbreviated as SBA-15m-a, SBA-15m-b, SBA-15m-c, SBA-15m-d, and SBA-15m-e according to the different active species. The PW or W active species were highly dispersed in the channels of the modified mesoporous materials. The interaction between PW or W species and amino groups grafted on the channel surface of SBA-15 led to the immobilization of PW or W species. Their catalytic activity in the epoxidation of cyclooctene with H₂O₂ as oxidant was investigated. Among them, SBA-15m-a showed the best performance, with 98.9% conversion and 98.4% selectivity. The catalyst could be reused for six times with a little decrease in activity.     

A novel potential-triggered SBA-15/PANI/PSS composite film for selective removal of lead ions from wastewater

In this study, a novel potential-triggered electroactive composite film consisting of mesoporous silica SBA-15, polyaniline (PANI), and polystyrenesulfonate (PSS) was fabricated in an aqueous electrolyte solution via a facile pulse potentiostatic method. The obtained composite film was characterized by Fourier transform infrared spectroscopy (FT-IR), thermogravimetric (TG) analysis, and scanning electron microscopy (SEM). The ion exchange properties were evaluated in a solution containing 0.1 M Pb(NO₃)₂ by using an electrochemical quartz crystal microbalance (EQCM) as well as cyclic voltammetry (CV) method. It was found that the uptake/release of Pb²⁺ ions in/from SBA-15/PANI/PSS composite film was successfully achieved by modulating the redox states of the electroactive composite film, and the composite film exhibited different ion exchange behaviors at different scan rates. Based on these results, the ion exchange mechanism was proposed. Compared with the PANI/PSS composite film, the SBA-15/PANI/PSS composite film had higher adsorption capacity as well as higher selectivity toward Pb²⁺ ions, which should be attributed to the 3D porous morphology of the composite film with more active sites in the mesoporous SBA-15. Remarkably, the film maintained a high stability over 97% even after 500 successive cycles. It is expected that this SBA-15/PANI/PSS composite film can serve as a promising electroactive material for the effective separation of Pb²⁺ ions from wastewater.

Open image in new window

Graphical abstract ?

     

Mesoporous hybrids containing Eu complexes covalently bonded to SBA-15 functionalized: Assembly, characterization and photoluminescence

A novel series of luminescent mesoporous organic-inorganic hybrid materials has been prepared by linking Eu³⁺ complexes to the functionalized ordered mesoporous SBA-15 which was synthesis by a co-condensation process of 1,3-diphenyl-1,3-propanepione (DBM) modified by the coupling agent 3-(triethoxysilyl)-propyl isocyanate (TEPIC), tetraethoxysilane (TEOS), Pluronic P123 surfactant as a template. It was demonstrated that the efficient intramolecular energy transfer in the mesoporous material Eu(DBMSi-SBA-15)₃phen mainly occurred between the modified DBM (named as DBM-Si) and the central Eu³⁺ ion. So the Eu(DBMSi-SBA-15)₃phen showed characteristic emission of Eu³⁺ ion under UV irradiation with higher luminescence quantum efficiency. Moreover, the mesoporous hybrid materials exhibited excellent thermal stability as the lanthanide complex was covalently bonded to the mesoporous matrix.     

Adsorption and structural properties of channel-like and cage-like organosilicas

Channel-like and cage-like mesoporous silicas, SBA-15 (P6mm symmetry group) and SBA-16 (Im3m symmetry group), were modified by introducing single ureidopropyl surface groups, mixed ureidopropyl and mercaptopropyl surface groups, and single bis(propyl)disulfide bridging groups. These hexagonal and cubic organosilicas were prepared under acidic conditions via co-condensation of tetraethyl orthosilicate (TEOS) and proper organosilanes using poly(ethylene oxide)-block-poly(propylene oxide)-block-poly(ethylene oxide) amphiphilic block copolymer templates, P123 (EO₂₀PO₇₀EO₂₀) and F127 (EO₁₀₆PO₇₀EO₁₀₆). The modified SBA-15 and SBA-16 materials were synthesized by varying the molar ratio of organosilane to TEOS in the initial synthesis gel. The removal of polymeric templates, P123 and F127, was performed with ethanol/hydrochloric acid solution. In the case of SBA-15 the P123 template was fully extracted, whereas this extraction process was less efficient for the removal of F127 template from the SBA-16-type organosilicas; in the latter case a small residue of F127 was retained. The adsorption and structural properties of the resulting materials were studied by nitrogen adsorption-desorption isotherms at −196^∘C (surface area, pore size distribution, pore volumes), powder X-Ray diffraction, CHNS elemental analysis and high-resolution thermogravimetry. The structural ordering, the BET specific surface area, pore volume and pore size decreased for both channel-like and cage-like mesoporous organosilicas with increasing concentration of incorporated organic groups.     

Application of mesoporous SiO2-Modified carbon paste electrode for voltammetric determination of epinephrine

Mesoporous SiO₂ of SBA-15 is reported to modify carbon paste electrodes for detecting epinephrine (EP). Carbon paste electrodes modified with synthesized SBA-15 show high sensitivity for voltammetric determination of EP, which is attributed to the strong adsorption ability of SBA-15 to EP and large surface area of the working electrode resulted from SBA-15 modification. The effects of pH value, amount of SBA-15 and scan rate were investigated. Under optimum conditions, the anodic peak current of EP was proportional to its concentration over the range from 1.0 × 10^?6 to 6.0 × 10^?5 mol L^?1 and the limit of detection was 6.0 × 10^?7 mol L^?1. The results show mesoporous SiO₂-modified carbon paste electrodes, particularly SBA-15-modificd electrodes, create new opportunities for sensitive, simple and suitable method in the electrochemical analysis of EP.     

改性中孔分子筛SBA-16薄膜的合成及表征

在酸性条件下, 以导电玻璃(ITO)为基底合成了SBA-16分子筛膜. 所制备的SBA-16膜孔径均匀, 具有体心立方结构(属于Im3m空间群), SBA-16膜的晶胞参数为18.6 nm. TEM, SEM和XRD等技术研究表明, 加入少量的AlCl₃盐于形成膜的母液并且采用RSiX₃对导电玻璃基底进行处理, 能够明显改善SBA-16膜的连续性而不影响孔结构. 红外(FTIR)研究结果表明, SBA-16膜的表面硅羟基和结晶水很少, 膜很稳定. XPS研究表明, 加入少量MnCl₂对SBA-16膜进行改性, 可以提高膜的导电性.     

Functionalized SBA-15 mesoporous silica in ion chromatography of alkali,alkaline earths,ammonium and transition metal ions

The retention properties of a SBA-15 mesoporous silica functionalized with –(CH₂)₃COOH groups, synthesized by a co-condensation route, were investigated for the ion chromatography of different cationic species. A systematic study on the effect of different eluent compositions containing non-complexing (methanesulfonic acid) or complexing (oxalic or pyridine-2,6-dicarboxylic acids) eluents, in the presence of organic modifiers (CH₃CN, CH₃OH, CH₃NH₂) on the retention of cations (Li⁺, Na⁺, K⁺, Ca²⁺, Mg²⁺, Sr²⁺, Ba²⁺, NH₄⁺, Cu²⁺, Ni²⁺, Zn²⁺, Cd²⁺, Co²⁺, Pb²⁺, Fe³⁺) chosen as model analytes and for their environmental importance, allowed us to elucidate the mechanisms (cation-exchange or complexation) involved in the retention on the SBA-15 phase. For the first time separations of cations on SBA-15 based stationary phases are investigated, providing the basis for further development of mesoporous silica chemistry for in-flow ion-exchange applications.     

Intense white light luminescent Dy3+ doped lithium borate glasses for W-LED: A correlation between physical,thermal, structural and optical properties

In this article the physical, thermal structural and optical properties of Dy³⁺ doped lithium borate glasses have been studied for white LED application. The emission spectra shows two intense emission bands at around 483 nm and 574 nm corresponds to the ⁴F_9/2 → ⁶H_15/2 and ⁴F_9/2 → ⁶H_13/2 transitions along with one feeble band at 663 nm corresponds to ⁴F_9/2 → ⁶H_11/2 transition. The average lifetime <τ> of Dy³⁺ were found to be about 2.95 and 4.94 ns for blue and yellow emission bands respectively. CIE chromaticity diagram shows glass LBD-4 containing 0.5 mol% Dy₂O₃ with colour co-ordinates x = 0.33 and y = 0.37 have highest emission intensity. These glasses having emission in the white region and thus can be used for bright white LED's and modern white LED bulbs.