Estimation of isotopic composition of plutonium from thermal reactors by neutron coincidence counting through isotopic correlation technique

Correlations have been established between %Eff ²⁴⁰Pu and various plutonium isotopes formed in thermal reactors. Based on these correlations, a method has been developed for the estimation of isotopic composition of plutonium obtained from thermal reactors. The method is simple, fast, non-destructive and finds application for the verification of plutonium isotopic composition in the finished products of known plutonium content. The method could be applied in the nuclear fuel fabrication to verify and confirm the fissile content (²³⁹Pu+²⁴¹Pu) specification. It has also been shown that in principle, similar correlations could be established for Pu obtained from different thermal reactor fuels with reactor specific fitting parameters.     

The determination of plutonium by mass spectrometry using a [242]-plutonium tracer

An isotopic dilution method is described for the determination ot plutonium in samples of irradiated uranium using a ²⁴²Pu tracer. An aliquot of tracer is added to the sample and the mixture treated to ensure isotopic exchange; plutonium is then separated by an ion exchange procedure and an isotopic analysis made using an M.S.5. mass spectrometer. The precision (3 σ) for an aliquot containing 0.1 μg plutonium is 0.6%. A possible application of the method would be its use for control analyses of the feed solution in a chemical plant processing natural uranium fuel elements as, for example, the Windscale primary separation plant.     

An inter-calibration campaign using various selected Pu spike isotopic reference materials

In nuclear safeguards, precise and accurate isotopic analyses are needed for two major elements from the nuclear fuel cycle: uranium and plutonium. This can be achieved by Isotope Dilution Mass Spectrometry (IDMS), which is one of the most reliable analytical techniques for the determination of plutonium amount content to a high level of accuracy. In order to achieve reliable isotope measurements isotopic reference materials with certified amount of plutonium and isotopic composition are required. At the Institute for Reference Materials and Measurements (IRMM) various plutonium spike reference materials for isotopes ²³⁹Pu, ²⁴⁰Pu, ²⁴²Pu and ²⁴⁴Pu are available. This enabled the setup of an inter-calibration campaign inter-linking selected plutonium spikes on a metrological basis applying state-of-the-art measurement procedures. The aim of this campaign is threefold: firstly to perform measurements on selected plutonium spike isotopic reference materials for quality control purposes, secondly to verify the amount content and the isotopic composition of the recently produced IRMM-1027m large sized dried (LSD) spikes and thirdly to demonstrate IRMM’s measurement capabilities for plutonium analysis via external quality tools. The obtained results using various spike isotopic reference materials will be presented and discussed in this paper. The measurement uncertainties of the IDMS results were calculated according to the guide to the expression of uncertainty in measurement (GUM).     

Some possibilities for the plutonium content determination in an irradiated nuclear fuel

This paper describes the results of the methods used for the plutonium content determination in an irradiated nuclear fuel from the first Czechoslovak atomic power station A1. The main attention was paid to the following methods: mass-spectrometric isotope dilution method, radiometric method and correlation dependence method based on the analysis of the burnt fuel. The principle and the accuracy of the individual methods are discussed.     

Reverse isotope dilution alpha spectrometry using plutionium-239 spike for determining plutonium concentration in high burn-up fuel samples without purification from americium-241 and a bulk of other impurities

A reverse isotope dilution alpha spectrometric /R-IDAS/ method using²³⁹Pu as a spike is described for the determination of plutonium concentration in high burn-up fuel samples wth²³⁸Pu/(²³⁹Pu+²⁴⁰Pu) alpha activity ratio >0.5, without resorting to any purification from²⁴¹Am and a bulk of other impurities. It involves the addition of a pre-clibrated spike solution to a known aliquot of the plutonium sample solution followed by source preparation using TEG as a spreading agent. The results obtained on a number of plutonium samples containing 20–80% of²⁴¹Am /alpha activity wise/ using this method are compared with those achieved by R-IDAS using purification with TTA, with respect to precision and accuracy. Precision and accuracy of 0.5% are demonstrated. This method eliminates the need of any separation and purification of plutonium from²⁴¹Am and a bulk of other impurities like uranium.     

Nuclear oxide fuel analysis

As a rule the analysis of nuclear oxide fuel includes the determination of uranium, plutonium, their isotopic composition, cation impurities, carbon, nitrogen, chlorine, fluorine, oxygen coefficient. In this paper we discuss different methods for the a analysis of unirradiated uranium and plutonium oxide fuelds used in the laboratories of the Analytical Chemistry Department: coulometry, emission analysis, chromatography, X-ray analysis. Much consideration is being given to the analysis of uranium and plutonium oxide samples and uranium-plutonium mixed fuels irradiated in the BOR-60 using mass-spectrometric (isotope dilution method) and radiometric techniques. The results of uranium and plutonium determination by these methods are compared. The main analytical characteristics of the methods are given.     

Comparison of alpha-spectrometry and alpha/gamma ratio method for the determination of americium in plutonium bearing fuel materials

Determination of americium is one of the requirements of chemical quality assurance of plutonium bearing fuel materials. Alpha-spectrometry is generally used for the determination of ²⁴¹Am in Pu bearing fuels since the efficiency of semiconductor detector used for alpha-spectrometry is independent of the alpha-particle energy in the 4 to 8 MeV range. However, this method has limitations for Pu samples containing extremely small or very large amounts of ²⁴¹Am. Thus an alternative methodology based on alpha/gamma (α/γ) activity ratio was developed and tested using different samples. The method is based on the determination of total γ-activity (of 60 keV peak) of an aliquot of the solution and the total α-activity present in the aliquot. The method is fast as it does not involve chemical separation of Pu and Am as required in the alpha-spectrometric method. Data obtained on synthetic and real life samples demonstrates the usefulness of the developed alpha/gamma ratio method for the determination of ²⁴¹Am in Pu bearing fuel samples.     

Determination of plutonium,americium and curium in airborne effluents of nuclear power plants

A radiochemical method has been developed for the determination of²³⁸Pu,^{239, 240}Pu,²⁴¹Am,²⁴²Cm and²⁴⁴Cm in airborne effluents of nuclear power plants. The method involves conversion of transuranium elements to acid-soluble forms, dissolution, purification, electrodeposition and alpha spectrometric determination. Final recovery ranged from 69.0 to 75.4% for plutonium and from 26.8 to 68.3% for americium and curium.     

A gamma-spectrometric method for the determination of plutonium isotope ratios

A gamma-spectrometric method using an intrinsic high resolution germanium detector has been developed for the determination of isotope ratios of plutonium from samples in solution form. The method is based on the assay of low energy gamma-rays of²³⁸Pu,²³⁹Pu,²⁴⁰Pu and²⁴¹Pu and does not require the use of branching intensities or the knowledge of detection efficiencies for different gamma rays. Since low energy gamma-rays are used, the effect of²⁴¹Am has also been studied. It is found that results are not affected up to 0.5 wt% of²⁴¹Am in plutonium samples. An accuracy of 3% is achievable in the determination of²⁴⁰Pu/²³⁹Pu and²⁴¹Pu/²³⁹Pu atom ratios as demonstrated by carrying out measurements on isotopic standards of plutonium.     

Recovery of americium from analytical solid waste containing large amounts of uranium,plutonium and silver

Trace metallic impurity analysis by spectroscopic techniques is one of the important steps of chemical quality control of nuclear fuel materials. Depending on the burn-up and the storage time of the fuel, there is an accumulation of ²⁴¹Am in plutonium based fuel materials due to β decay of ²⁴¹Pu. In this paper, attempts were made to develop a method for separation of ²⁴¹Am from 1.2 kg of analytical solid waste containing 70% U, 23% Pu, 5% Ag and 1–2% C as major constituents along with other minor constituents generated during trace metal assay of plutonium based fuel samples by d. c. arc carrier distillation atomic emission spectrometry. A combination of ion exchange, solvent extraction and precipitation methods were carried out to separate ~45 mg of ²⁴¹Am as Am(NO₃)₃ from 15 L of the analytical waste solution. Dowex 1×4 ion exchange chromatographic method was used for separation of Pu whereas 30% TBP–kerosene was utilized for separation of U. Am was separated from other impurities by fluoride precipitation followed by conversion to nitrate. The recovery of Pu from ion exchange chromatographic separation step was ~93% while the cumulative recovery of Am after separation process was found to be ~90%.     

Sequential isotopic determination of plutonium,thorium, americium and uranium in the air filter and drinking water samples around the WIPP site

The simultaneous determination of actinides in air filter and water samples around the WIPP site have been demonstrated. The analytical method is based on the selective separation and purification by anion exchange and Eichrome-TEVA, TRU and DGA-resin followed by determination of actinides by alpha spectrometry. Counting sources for alpha spectrometric measurements were prepared by microcoprecipitation on neodymium fluoride (NdF₃). Radiochemical yields were determined using ²⁴²Pu, ²²⁹Th, ²⁴³Am and ²³²U as tracers. The validation of the method is performed through the analysis of reference materials or participating in laboratory intercomparison programs. The plutonium concentrations in aerosols varied seasonally, being highest in spring and summer due to the spring-time enhanced wind-storm transportation of radioactive aerosols from the stratosphere to the troposphere. The ²³⁸Pu/^239+240Pu activity ratio in the aerosol samples is typically close to that of global fallout from historic above-ground nuclear weapons testing. The results presented here indicate that the source of plutonium in the WIPP environment results mainly from global nuclear fallout and there is no evidence of increases in radiological contaminants in the region that could be attributed to releases from the WIPP.     

Extraktionschromatographische Trennung von Uran,Plutonium und Spaltprodukten

An extraction chromatographic method has been developed to separate plutonium and uranium from irradiated uranium fuel samples. Tributylphosphate fixed on polytetrafluoro ethylene was used as stationary phase and HNO₃ of various concentrations as mobile phase. The separation of plutonium by reduction with H₂SO₃ was studied in column experiments. The method was applied to the separation of irradiated U/Mg-fuel with a Pu/U ratio of 1∶400.     

Separation of neptunium, plutonium, americium and curium from uranium with di-(2-ethylhexyl)-phosphoric acid (HDEHP) for radiometric and ICP-MS analysis

The possibility of using di-(2-ethylhexyl)-phosphoric acid (HDEHP) in solvent extraction for the separation of neptunium, plutonium, americium and curium from large amounts of uranium was studied. Neptunium, plutonium, americium and curium (as well as uranium) were extracted from HNO₃, whereafter americium and curium were back-extracted with 5M HNO₃. Thereafter was neptunium back-extracted in 1M HNO₃ containing hydroxylamine hydronitrate. Finally, plutonium was back-extracted in 3M HCl containing Ti(III). The method separates²³⁸Pu from²⁴¹Am for α-spectroscopy. For ICP-MS analysis, the interferences from²³⁸U are eliminated: tailing from²³⁸U, for analysis of²³⁷Np, and the interference of²³⁸UH⁺ for analysis of²³⁹Pu. The method has been used for the analysis of actinides in samples from a spent nuclear fuel leaching and radionuclide transport experiment.     

ICP-MS analysis of plutonium activities and <Superscript>240</Superscript>Pu/<Superscript>239</Superscript>Pu ratio in alpha spectrometry planchet deposits

Plutonium isotopes were measured by alpha-spectrometry and ICP-MS in sediment samples from two European lakes: Blelham Tarn in U.K. and Stechlin lake in Germany. The ICP-MS measurements were made after alpha-spectrometry counting of the planchets. The planchets were prepared by traditional electrodeposition method after radiochemical extraction, separation and purification of the Pu fraction. A short radiochemical separation using plutonium selective resin, between the two spectrometry measures, is presented. The results show that these two complementary methods are in good agreement, the plutonium activity concentrations are the same. Alpha-spectrometry allows the ²³⁸Pu determination and ICP-MS individual measurement of ²³⁹Pu and ²⁴⁰Pu. ²³⁸Pu/^239+240Pu and ²⁴⁰Pu/²³⁹Pu ratios are calculated to determine the plutonium contamination source. With the results of these two techniques, it could be demonstrate that the plutonium is of global fallout origin.     

Plutonium in soils and plants around the IRT-2000 research reactor in Sofia

The concentration of the plutonium isotopes²³⁸Pu and^239+240Pu in the surroundings of the research reactor was measured by application of a very sensitive and selective radionalytical procedure for the determination of plutonium in soils and plants, including lichens and mosses as bioindicators. All measured concentrations are in the range of variation of the global contamination with plutonium caused by fallout of atmospheric nuclear weapon tests and burning of satellites in the atmosphere. An additional contamination by plutonium isotopes due to discharges from the reactor in the past is not detectable.This work was sponsored by the Bulgarian Ministry of Science and Higher Education under Research Contract No. 281 and was performed with the support of Kernforschungszentrum Karlsruhe.     

A combined method for the determination of the isotopic vector of plutonium isotopes in environmental samples

A combination of alpha-spectrometry, liquid scintillation counting (LSC) and accelerator mass spectrometry (AMS) was used for the determination of plutonium isotopes. ²³⁸Pu and ^239+240Pu were measured by alpha-spectrometry after separation of Pu by anion-exchange using ²³⁶Pu tracer as recovery monitor. After alpha-measurement, one part of the sample was dissolved for determining ²⁴¹Pu by LSC. Another part was used for the measurement of the ²⁴⁰Pu/²³⁹Pu atom ratio by AMS at VERA. Thus, it was possible to obtain complete information on the Pu isotopic composition of the samples. This method was applied to environmental reference samples and samples contaminated from nuclear reprocessing.     

Determination of the plutonium concentration by isotope dilution mass spectrometry using239Pu as a spike

A method is described for the determination of plutonium concentration in the presence of a bulk of other impurities by isotope dilution mass spectrometry /IDMS/ using²³⁹Pu as a spike. The method involves the addition of²³⁹Pu spike / 90 atom%/ to samples with²³⁹Pu / 70 atom%/ and vice versa. After ensuring chemical exchange between the sample and the spike isotopes, plutonium is purified by conventional anion exchange procedure in 7M HNO₃ medium.²³⁹Pu/²⁴⁰Pu atom ratio in the purified spiked sample is determined with high precision /better than 0.1%/ using a thermal ionization mass spectrometer. Concentration of plutonium in the sample is calculated from the changes in²³⁹Pu/²⁴⁰Pu atom ratio in the spiked mixture. Results obtained on different plutonium samples using²³⁹Pu as a spike are compared with those obtained by the use of²⁴²Pu spike. Precision and accuracy comparable to those achieved by using²⁴²Pu are demonstrated. The method provides an alternative in the event of non-availability of enriched²⁴²Pu or²⁴⁴Pu required in IDMS of plutonium and at the same time, offers certain advantages over the use of²⁴²Pu or²⁴⁴Pu spike.     

The dynamic movement of plutonium in an underground nuclear test with implications for the contamination of groundwater

Summary The recent discovery of the migration of plutonium in groundwater away from underground nuclear tests at the Nevada Test Site has spawned considerable interest in the mechanisms by which plutonium may be released to the environment by a nuclear explosion. A suite of solid debris samples was collected during drilling through an expended test cavity and the overlying collapse chimney. Uranium and plutonium were analyzed for isotope ratios and concentrations using high precision magnetic sector inductively coupled mass spectrometry. The data unequivocally shows that plutonium may be dispersed throughout the cavity and chimney environment at the time of the detonation. The ²³⁹Pu/²⁴⁰Pu ratios are also fractionated relative to initial plutonium isotope ratio for the test device. Fractionation is the result of the volatilization of uranium and production of ²³⁹Pu by the reaction ²³⁸U(n,γ). We conclude that for the test under consideration plutonium was deposited outside of the confines of the cavity by dynamic processes in early-time and it is this plutonium that is most likely transferred to the groundwater regime.     

Low-level determination of plutonium by gamma and L X-ray spectroscopy

We have developed an analytical method for detection of²³⁹Pu in aqueous samples at concentrations as low as 10^–10M. This nuclear counting technique utilizes the uranium L X-rays, which follow the alpha-decay of plutonium. Because L X-rays are specific for the element and not for the individual isotope, the isotopic composition of the plutonium sample must be known. The counting efficiency in the 11–23 keV range is determined from a plutonium standard, and the concentration of the sample is then calculated from the L X-ray count and the isotopic composition. The total L X-ray count is corrected for possible contributions from other radionuclides present as impurities by measuring the low-energy gamma-spectrum for each contaminant to establish specific photon/X-ray ratios. The ratios are important when²⁴¹Pu and²⁴²Pu are measured, because the respective decay chain members produce non-U L X-rays. This new method can replace the use of labor-intensive radiochemical separation techniques and elaborate activation methods for analysis of²³⁹Pu in aqueous samples. It is also applicable for assaying plutonium in liquid wastes that pose possible hazards to the environment.     

Age determination of plutonium using inductively coupled plasma mass spectrometry

The age of plutonium is defined as the time since the last separation of the plutonium isotopes from their daughter nuclides. In this paper, a method for age determination based on analysis of ²⁴¹Pu/²⁴¹Am and ²⁴⁰Pu/²³⁶Pu using ICP-SFMS is described. Separation of Pu and Am was performed using a solid phase extraction procedure including UTEVA, TEVA, TRU and Ln-resins. The procedure provided separation factors adequate for this purpose. Age determinations were performed on two plutonium reference solutions from the Institute for Reference Materials and Measurements, IRMM081 (²³⁹Pu) and IRMM083 (²⁴⁰Pu), on sediment from the Marshall Islands (reference material IAEA367) and on soil from the Trinity test site (Trinitite). The measured ages based on the ²⁴¹Am/²⁴¹Pu ratio corresponded well with the time since the last parent-daughter separations of all the materials. The ages derived from the ²³⁶U/²⁴⁰Pu ratio were in agreement for the IRMM materials, but for IAEA367 the determination of ²³⁶U was interfered by tailing from ²³⁸U, and for Trinitite the determined age was biased due to formation of ²³⁶U in the detonation of the “Gadget”.