聚合硅酸硫酸铁和聚合硫酸铁处理黄河水的效果及其絮体特性研究

采用聚合硅酸硫酸铁(PFSS)和聚合硫酸铁(PFS)两种无机高分子混凝剂处理黄河水,考察了两种混凝剂对浊度和UV254的去除效果,并结合混凝过程中絮体zeta电位的变化,分析了两种混凝剂的混凝机理.通过激光粒度仪在线观察混凝过程中絮体的生长情况,发现PFSS比PFS生成的絮体生长速度快,尺寸大.对形成的絮体施加不同强度的剪切力,通过观察絮体粒径的变化来比较絮体的强度,发现PFSS生成的絮体强度较大.研究了在不同剪切强度和不同剪切时间下絮体的破碎程度和絮体的恢复能力(分别以破碎因子Bf和恢复因子Rf表示),发现在强剪切力和长剪切时间下Bf和Rf均较大;在相同条件下PFSS生成絮体的Bf较小而PFS生成絮体的Rf较大,这表明前者的抗剪切能力较强,而后者具有更强的再生能力.     

自制聚合硫酸铁对不同废水的净化效果

聚合硫酸铁(PFS)是一种新型无机高分子絮凝净水剂,有极强的混凝能力,沉降速度快,适用pH范围广,腐蚀性小,净水效果好;同时投药量少、费用低,处理后水质优良、无毒,不产生铝污染;且有良好的破油、除臭、脱色作用,故具有很好的发展前景。由于工业废水成分复杂,不同类型废水的成分有很大差别,因此同一净水剂不可能对所有废水的净化条件和效果都完全一致[1]。本文采用废铁屑和废酸自制固体PFS净水剂,对垃圾、印染、制药三类废水进行了净化条件及效果的试验,确定了废水净化时的最适宜pH值、净水剂用量、净化时间等,为该净水剂的实际应用提…     

Coagulation behaviors and in-situ flocs characteristics of composite coagulants in cyanide-containing wastewater: Role of cationic polyelectrolyte

In this paper,composite coagulants(PFS,PFSC05,PFSC1 and PFSC5),prepared by mixing polyferric sulfate(PFS)and cationic polyelectrolyte(CP)coagulants with different weight percent(Wp)of CP(Wp=0%,0.5%,1%and 5%,respectively),were adopted to treat cyanide-containing wastewater.PFSC5 exhibited superior coagulation performances at optimal conditions:the removal of total cyanide(TCN)and chemical oxygen demand(COD)was 95%–97%and 50%–55%,respectively.The effects of CP on the properties and structure of flocs were investigated by laser diffraction instrument and small-angle laser light scattering(SALLS),respectively.The results show that the flocs of PFSC5 have higher growth rate,higher strength factor and lower recovery factor than other flocs.They are also much denser and more uniform owing to the higher fractal dimension(Df)and less microflocs(10–100 m).Furthermore,the dense structure of the PFSC5 flocs can be restored after shear and is more resistant to hydraulic conditions.Particularly,detailed morphology evolution of the flocs was in-situ detected by on-line particle imaging.Due to strong ionic strength in wastewater,the CP in PFSC5 plays a significant role of adsorption,while the main mechanism of CP is electrostatic patch aggregation during the PFSC05 systems.     

聚硅酸硫酸铁/壳聚糖复合絮凝剂的制备及其在废水处理中的应用

制备了无机高分子复合絮凝剂聚硅酸硫酸铁（PFSS）和助凝剂壳聚糖（CTS）,考察了影响合成及絮凝剂应用的因素,探讨了其组成、投加量以及pH值对城市废水絮凝效果的影响,通过对模拟废水和城市废水絮凝试验,得出最佳的合成和应用条件：n（Fe）∶n（Si）=1∶1,PFSS的碱化度为1.5,聚合硫酸铁（PFS）的pH=2,聚硅酸（PS）的活化时间为1.5 h;n（PFSS）∶n（CTS）=5∶1,投加量为(20+4) mg/L,pH值的范围为6～9,沉降时间为15 min。 复合絮凝剂（PFSS-CTS）在最佳条件下浊度、色度、COD的去除率分别达到95.04%、91.26%和83.45%。     

有机高分子与聚合硫酸铁的复配特性

研究了水溶性有机高分子(OP)与聚合硫酸铁(PFS)的复配特点,从分子结构和溶剂化角度探讨了OP在PFS中的稳定机制,并采用FT-IR、SEM和X射线衍射探讨了OP与PFS的相互作用.结果表明:具有吡咯环结构的聚二甲基二烯丙基氯化铵、聚二乙基二烯丙基氯化铵和聚乙烯吡咯烷酮能与PFS复配,且具有较好的稳定性;OP与PFS形成了互相融合的复合体系,主要与PFS中Fe4.67(SO4)6(OH)2.20H2O物相发生相互作用.     

两性田菁胶在处理生活污水中的助凝作用

研究了以聚合硫酸铁为主凝剂、两性田菁胶(ASG)为助凝剂处理城市生活废水的各种影响因素.实验结果表明:聚合硫酸铁和两性田菁胶分别以200mg/L和10mg/L的复配浓度、pH值接近7时混凝效果最佳,CODCr去除率达到近80%,处理后废水CODCr达到国家排放标准.     

铅及铅锑合金阳极膜中硫酸铅的氧化过程

应用电位阶跃和交流阻抗法分别研究铅和Pb-5wt% Sb合金在4.5mol·dm^-^3H~2SO~4(30℃)中于1.3V(vs. Hg/Hg~2SO~4, 下同)生长20min后的阳极膜在0.9V还原5min后再在1.4V将膜中硫酸铅氧化的过程。实验结果表明在0.9V还原二氧化铅而得到的硫酸铅能在1.4V于1min内氧化为二氧化铅。这是由于此种硫酸铅处于硫酸铅颗粒表层的缘故。至于颗粒内部由铅直接生成的硫酸铅的氧化为二氧化铅就要缓慢得多。合金中的锑能使二氧化铅晶核形成和生长速率显著降低。     

Chemiluminescence high-performance liquid chromatography for the determination of hyaluronic acid, chondroitin sulphate and dermatan sulphate.

A sensitive chemiluminescence high-performance liquid chromatographic method has been developed for the determination of hyaluronic acid, chondroitin sulphate and dermatan sulphate as their unsaturated disaccharide-dansylhydrazine derivatives involving an effective sample clean-up system. The dansylhydrazones of the unsaturated disaccharides derived from the hyaluronic acid, chondroitin sulphate and dermatan sulphate by chondroitinase ABC and/or chondroitinase ACII, were separated by reversed-phase chromatography using a mixture of 0.1 M sodium acetate buffer (pH 6.0) and 80% acetonitrile on a column (250 mm x 4.0 mm I.D.) packed with amide-80 silica beads (5 microns diameter). For post-column elution in the chemiluminescence system, 1 mM bis[2-(3,6,9-trioxadecanyloxycarbonyl)-4-nitrophenyl]oxalate and 3mM hydrogen peroxide in acetonitrile were used. The detection limit of each glycosaminoglycan was 100 fmol. The method was applicable to the determination of the levels of hyaluronic acid, chondroitin sulphate and dermatan sulphate in rat peritoneal mast cells.     

聚硅硫酸亚铁的混凝特性及影响因素

混凝剂;聚合硫酸铁;水处理;聚硅硫酸亚铁的混凝特性及影响因素     

Modelling of calcium sulphate solubility in concentrated multi-component sulphate solutions

The chemistry of several calcium sulphate systems was successfully modelled in multi-component acid-containing sulphate solutions using the mixed solvent electrolyte (MSE) model for calculating the mean activity coefficients of the electrolyte species. The modelling involved the fitting of binary mean activity, heat capacity and solubility data, as well as ternary solubility data. The developed model was shown to accurately predict the solubility of calcium sulphate from 25 to 95 °C in simulated zinc sulphate processing solutions containing MgSO₄, MnSO₄, Fe₂(SO₄)₃, Na₂SO₄, (NH₄)₂SO₄ and H₂SO₄. The addition of H₂SO₄ results in a significant increase in the calcium sulphate solubility compared to that in water. By increasing the acid concentration, gypsum, which is a metastable phase above 40 °C, dehydrates to anhydrite, and the conversion results in a decrease in the solubility of calcium sulphate. In ZnSO₄–H₂SO₄ solutions, it was found that increasing MgSO₄, Na₂SO₄, Fe₂(SO₄)₃ and (NH₄)₂SO₄ concentrations do not have a pronounced effect on the solubility of calcium sulphate. From a practical perspective, the model is valuable tool for assessing calcium sulphate solubilities over abroad temperature range and for dilute to concentrated multi-component solutions.     

An improved turbidimetric procedure for the determination of sulphate in plants and soils

A rapid turbidimetric procedure for the determination of sulphate in soils and plants has been developed with sorbitol as stabilizing agent. When used in a concentration of 20% in the final volume, the sorbitol regulates the size of the BaSO(4) particles formed and stabilizes them against sedimentation, growth and aggregation for long periods of time. The conditions of precipitation are not rigorous, as they are in similar procedures. Linearity of the calibration curve up to 50 ppm of sulphate and good reproducibility are special attributes of the procedure.     

Effect of temperature and pH on droplet aggregation and phase separation characteristics of flocs formed in oil–water emulsions after coagulation

Coagulation process is used for destabilization of emulsions to promote aggregation of oil droplets on flocs which can be subsequently removed by sedimentation or flotation. The objectives of this study were to investigate the effect of temperature and pH on the effectiveness of destabilization of olive oil–water emulsions in relation to floc morphology and aggregation characteristics of oil droplets, and to quantify the ability of flocs to capture and separate oil. A cationic polyelectrolyte was used for the coagulation of oil droplets in edible olive oil–water emulsions using a jar test apparatus. The flocs formed in olive oil–water emulsions after coagulant addition were analyzed using microscopic image analysis techniques. Fractal dimension, radius of captured oil droplets on flocs, number of oil droplets aggregated on flocs, and floc size were used to quantitatively characterize and compared the effectiveness of the coagulation process at different conditions (pH and temperature) and the ability of flocs to remove oil from water. Analysis of microscopic images showed that floc size was not always the best measure of effectiveness of coagulation process in oil–water emulsions. The flocs forming at different pH levels and temperatures had significant morphological differences in their ability to aggregate different sizes and numbers of oil droplets, resulting in significant differences in their ability for separating oil. Fractal dimension did not correlate with the ability of flocs to aggregate oil droplets nor the total amount of oil captured on flocs. Temperature had a significant effect on droplet size and number of droplets captured on flocs. The differences in floc sizes at different temperatures were not significant. However, the flocs forming at 20 °C had fewer but larger droplets aggregating larger amounts of oil than flocs formed at 30 °C and 40 °C. The size of droplets at different pH levels was similar, however, there were significant differences in number of droplets aggregating on flocs and floc sizes. The amount of oil captured on flocs at pH 7 and pH 9 was significantly higher than those at pH 5 and pH 11. The calculated fractal dimensions of the flocs (all less than 1.8) indicated that the coagulation process was diffusion limited implying that there was no repulsion between the colliding particles (i.e., droplets and flocs); hence, each collision between flocs and droplets resulted in attachment.     

Development and validation of the stability-indicating LC-UV method for the determination of cefoselis sulphate

The stability-indicating LC assay method was developed and validated for quantitative determination of cefoselis sulphate in the presence of degradation products formed during the forced degradation studies. An isocratic, RP-HPLC method was developed with C-18 (250 × 4.6 mm, 5 μm) column and 12 mM ammonium acetate-acetonitrile (95:5 V/V) as a mobile phase. The flow rate of the mobile phase was 1.0 mL min⁻¹. Detection wavelength was 260 nm and temperature was 30°C. Cefoselis similarly to other cephalosporins was subjected to stress conditions of degradation in aqueous solutions including hydrolysis, oxidation, photolysis and thermal degradation. The developed method was validated with regard to linearity, accuracy, precision, selectivity and robustness. The method was applied successfully for identification and determination of cefoselis sulphate in pharmaceuticals and during kinetic studies.     

Volumetric studies in oxidation-reduction reactions: Reduction with ferrous ethylenediamine sulphate ceric sulphate method

Ferrous ethylenediamine sulphate has been used as a reducing agent in acid medium for the indirect volumetric estimations of potassium chlorate, potassium bromate, potassium metaperiodate, potassium dichromate, potassium ferricyanide, potassium permanganate, potassium persulphate, hydrogen peroxide and ceric sulphate. The excess of ferrous ethylenediamine sulphate added to each of the substances in acid medium was titrated with standard ceric sulphate solution using ferroin as an indicator.     

Spectrofluorimetric determination of guanethidine sulphate,guanfacine hydrochloride,guanoclor sulphate and guanoxan sulphate in tablets and biological fluids,using benzoin

A sensitive and rapid Spectrofluorimetric method for the determination of guanethidine sulphate, guanfacine hydrochloride, guanoclor sulphate and guanoxan sulphate in tablets and spiked human serum and urine samples is described. The method is based on the reaction of monosubstituted guanidino compounds in an aqueous potassium hydroxide solution with benzoin, in the presence of -mercaptoethanol and sodium sulphite. Highly fluorescent derivatives were obtained, with excitation and emission maximum wavelengths around 325 and 430 nm, respectively. In optimal reaction conditions, the linearity ranges were 0.04–0.28 g/ml, with relative standard deviations less than 2%. The method has been successfully applied to the determination of these drugs in tablets. The results are highly correlated with the B.P. method. Chloroform (or for guanoxan dichloromethane) was used to extract the drugs from serum and urine at basic pH, followed by the proposed fluorimetric method. The limit of detection is 0.02 g/ml for the selected drugs.     

Volumetric Studies In Oxidation-Reduction Reactions: Oxidation with ceric sulphate ferrous ethylenediamine sulphate method

Ceric sulphate has been used as an oxidizing agent in acid medium for the indirect volumetric determinations of ferrous ammonium sulphate, cuprous chloride, potassium thiocyanate, sodium thiosulpliate, sodiuin nitrite, hydrogen peroxide, sodium oxalate, hydroquinone and pyruvic acid. The excess of ceric sulphate added to each of the substances in acid medium was titrated with standard ferrous ethylenediamine sulphate solution using ferroin as an indicator.     

Liquid chromatographic assay for constituent disaccharides of hyaluronic acid and chondroitin sulphate isomers

An improved high-performance liquid chromatographic (HPLC) method for unsaturated disaccharides prepared from hyaluronic acid and various chondroitin sulphate and dermatan sulphate isomers was developed, which involves an ion-exchange resin prepared from a sulphonated styrene-divinylbenzene copolymer. The retention times of the individual unsaturated disaccharides were unique and reproducible, the disaccharides appearing in the following order: unsaturated non-sulphated disaccharide derived from hyaluronic acid, then unsaturated 6-sulphated, non-sulphated and 4-sulphated disaccharides from chondroitin sulphate isomers. Unsaturated disulphated disaccharide G had a much shorter retention time than the unsaturated non-sulphated disaccharide derived from hyaluronic acid. The contents of these individual unsaturated disaccharides could be determined with similar sensitivities on the basis of their ultraviolet absorbance. Selective and unique retention times and good resolutions were found for various unsaturated disulphated and trisulphated disaccharides. The proposed method can be used to determine various chondroitin sulphate and dermatan sulphate isomers in addition to hyaluronic acid in amounts as small as 100 ng to 8 micrograms. The practicality of this method was verified by its application to the separation and determination of the different types of chondroitin sulphate and dermatan sulphate isomers derived from human arteries in the presence of appreciable amounts of hyaluronic acid.     

Aluminum sulphate hydrates

Three different calculation methods of deriving kinetic parameters (activation energy and preexponential factor) from dynamic TG data have been applied for the sulphate decomposition stage of the aluminum sulphate octadecahydrate. The constant rate experiments were carried out by Derivatograph and DuPont thermobalances. The three parameters estimation methods included a simple differential method, the classical Coats-Redfern and a new direct integral method. The fits of the curves obtained by these procedures were compared both graphically and numerically. It was found that the direct integral method gave the most satisfactory results. With the order type reaction models this method in each case produced the smallest residual deviation values and the best fitting curves compared to those obtained by the other two methods. The activation parameters calculated by the differential method were not acceptable at all, for the estimated curves were very far from the measured ones.     

Anodic reactions of sulphate in molten salts

Electrochemical behaviour of sulphate under anodic polarization in molten sodium chloride, cryolite and sodium fluoride was investigated by cyclic voltammetry and chronopotentiometry at the temperatures of 820°C, 1010°C, and 1000°C, respectively. Using a platinum working electrode, two waves were observed on the chronopotentiograms in the systems: NaCl-Na₂SO₄ and Na₃AlF₆-Na₂SO₄. The first wave was attributed to the formation of oxygen. The second wave probably originated from the reaction of oxygen with platinum, or from oxidation of SO₃ decomposition products. Three waves were observed for the anodic process of sulphate ions dissolved in molten sodium fluoride. The first wave was attributed to the formation of oxygen. The second and the third wave were attributed to the formation of PtO and PtO₂. This conclusion was supported by cyclic voltammetry experiments of the in-situ formed sulphide in molten NaCl at 820°C and by chronopotentiometry on a gold working electrode in the system NaCl-Na₂SO₄, where no anodic wave was observed.     

Raman scattering study of diglycine sulphate and ammonium sulphate double salt crystals

Raman spectra have been recorded for diglycine sulphate and ammonium sulphate double salt crystals (DGSAS) at room temperature. From a comparison between our results and the i.r. and Raman spectra of the amino acids and ammonium sulphate crystals, the functional groups have been ascribed to particular positions of the bands in the Raman spectra of DGSAS crystals.