适用于色敏解调的光位移传感器宽带LED

为保证光位移传感器的工作性能,输入光源在500~800 nm波长范围内需具有较高的光谱能量,照明用LED波长在700 nm以上光谱能量陡降,限制了传感器的工作范围.针对照明用LED光谱能量不足的问题,研制出适用于色敏解调光位移传感器的宽带LED光源.首先利用单色仪对光位移传感器色敏元件WS7.56的性能进行了测试,依据色敏解调结果提出了光位移传感器正常工作所需的输入光源的光谱能量阈值.在照明用LED光谱特性基础上,配比掺杂氮氧化物红色荧光粉提升LED红光及近红外光光谱能量,得到了满足输入光源光谱能量阈值的宽带LED.最后,对该宽带LED光位移传感器进行了位移测量实验,实验结果较使用照明用LED光源有明显改善,位移解调线性度良好.本文研制的宽带LED光源体积小、效率高,是光位移传感器较为理想的宽带光源.     

Optical path automatic compensation low-coherence interferometric fibre-optic temperature sensor

An interferometric fibre-optic temperature sensing system employing a light emitting diode (LED) as the broadband optical source and a single mode fibre coil which was fabricated in a definite length as the sensor head is described. A reference fibre line transmitting back and forth along the same path as the sensing transmitting fibre is used, so the change caused by the environmental temperature fluctuation of the fibre path can automatically be compensated. The sensitivity of the sensing system can be easily improved by using the long length of the sensing fibre. The experiment results of the sensing gauge length versus the sensitivity are given. Two typical wavelengths (1300 and 1550 nm). LED sources are used, it is shown that the sensitivity of the system between the two wavelengths is different. The experimental curve of the resolution characteristic of the system related to the length of sensing fibre coil is also discussed.     

Dual wavelength referencing of optical fibre sensors

Dual wavelength configurations normally employed to eradicate the effects of variable signal losses in intensity-dependent optical sensors are discussed. Particular attention is paid to the referencing capability of each configuration in relation to the major sources of measurement contamination. Illustrative examples of generic type sensor system implementations are provided and assessed to identify areas of any serious shortcomings. It is found that while full referencing can be achieved with both single and dual LED systems the maximum achievable performance will be dependent on the extent of differential spectral effects which can occur because of a finite wavelength separation between the two optical signals.     

An all-fibre multi-parameter sensor for composite structures based on a chirped fibre Bragg grating

An all-fibre multi-parameter sensor for composite structures based on a chirped optical fibre Bragg grating (CFBG) has been studied theoretically and experimentally. The principle of multi-parameters sensing with a single CFBG is based on that the centre wavelength and the FWHM (full width at half maximum) in the reflection spectrum of a CFBG vary linearly with the temperature and/or the axial stress. A wavelength matched optical fibre long period grating (LPG) and another wavelength matched reference CFBG (CFBGR) have been used to interrogate the signal of the sensor CFBG (CFBGS). The temperature and strain of the composite structure have been monitored real-time with one CFBG as a single sensor head. The temperature resolution of 0.12°C and the strain resolution of 1.1μ? for a composite structure have been realized in experiments. The experiment results agree well with the theoretical analyses.     

Paper tape data transmission by wavelength multiplexing through a single fibre

Described is an optical system for transmitting paper tape data through a single fibre. It presents an application of wavelength multiplexing in optical fibre transmission. Each channel is coded by its own wavelength and the different wavelengths pass independently through the fibre, transmitting different information. Advantages of such a system are enlarged transmission capacity and a simple coding and decoding technique for varied channels without any moving parts.     

Temperature-Insensitive Chemical Sensor with Twin Bragg Gratings in an Optical Fibre

To reduce temperature sensitivity of the fibre Bragg grating （FBG） chemical sensor, a simple method is proposed by measuring the peak wavelength difference between an etched FBG and an un-etched one in an optical fibre. Thermal characteristics and chemical sensitivity of the sensor are experimentally investigated. The experimental results indicate that the etched FBG and the rest one have almost the same thermal response, and concentration changes of the surrounding chemical solutions can be detected by measuring the peak wavelength difference between them. The sensor has been used to measure the concentrations of propylene glycol solutions and sugar solutions, and it could detect 0.7% and 0.45% concentration changes for them with an optical spectrum analyser in resolution of 10pm.     

Ring fibre laser with interferometer based in long period grating for sensing applications

This work presents two distinct configurations based on phase-wavelength conversion using a ring fibre laser with two different long period gratings interferometer topologies. The sensors are interrogated by analysing the wavelength change of the emission laser, which is directly dependent on the interferometer phase change. The first configuration integrates a Mach-Zehnder interferometer, which is based on a pair of long period gratings and is used as sensing head for bending radius and longitudinal strain measurement. The second configuration, comprehends a Michelson interferometer, which is based on a single LPG and a fibre end mirror and is used as a liquid level sensor or as an optical refractometer.     

150 Mbits−1 ch−1 12-channel optical parallel interface using an LED and a PD array

An optical fibre parallel interface has been developed for card-cage to card-cage and board-to-board interconnections, representing a practical and promising optical interconnection. For a system design of a 12 channel, 150 Mbits^–1 ch^–1 optical parallel interface over a distance of 100 m, it is shown that the choice of a long wavelength LED/PD array with graded index optical fibre array meets the requirements for both power budget and skew limitation over this transmission distance. A 7 mm thick compact package transmitter and receiver module was developed, employing a Zn-doped, mesa structure, 1.3m LED array and an isolated InGaAs PD array. An optical parallel transmission experiment over 100 m was successfully demonstrated using these modules.     

激光回馈效应及其传感应用研究的进展

对基于激光回馈效应的传感应用研究进展进行了综述。由于激光回馈引起激光器功率波动一个条纹对应外部反射镜移动半个光波波长,功率波动深度与传统双光束干涉系统相当,基于该现象的激光回馈干涉仪与传统的干涉仪相比具有相同的相位灵敏度。但其结构简单、紧凑、易准直的特点,引起了国内外科研者浓厚的兴趣,开发了很多全新概念、经济实用的精密测量仪器。对激光回馈效应在位移测量、速度测量、振动测量、距离测量、角度测量和形貌测量中的原理进行了介绍,同时对各传感应用系统进行了评述。     

Properties of a gold-deposited surface plasmon resonance-based glass rod sensor with various light-emitting diodes and its application to a refractometer

The performance of a simple sensor system prepared using gold (Au)-deposited glass rods of 1 to 4 mm in diameter with a deposition length of 100 mm based on surface plasmon resonance (SPR) is presented. The sensor properties of the Au-deposited glass rods of 2 mm in diameter with deposition lengths of 10 to 100 mm are also presented. The sensor system consists of a light-emitting diode (LED) as the light source and a photodiode (PD) as the detector. The response curves and sensor properties of the Au-deposited glass rod with a Au film thickness of 45 nm obtained by using three LEDs with yellowish green (563 nm), red (660 nm), and infrared (940 nm) emissions were investigated. The results were compared with those of a corresponding Au-deposited optical fiber sensor with a core diameter of 0.2 mm. Though the sensitivity, response, and detection limit of the Au-deposited glass rod sensor are lower than those of the optical fiber sensor, the fabrication and handling of the Au-deposited glass rod sensor are easier because of the robustness. Since the dielectric constant of Au changes with the light wavelength, the sensor properties of both the Au-deposited glass rod sensor and the optical fiber sensor depend strongly on the wavelength of the incident light and can be controlled by changing the LED emission wavelength. This sensor system is a new SPR-based refractometer with easy construction and operation. Ethanol concentrations in various spirits were measured with this SPR-based refractometer and the results agreed well with those measured with an Abbe refractometer.     

反射式光纤温度传感器

本文根据半导体GaAs材料带隙随温度变化的原理,对采用单根光纤作双向传输光信号的反射光纤温度传感器进行了试验研究。由微型计算机控制的光纤测温系统的测温范围为0～150℃精度±1℃,分辨率0.2℃。     

双法布里—珀罗干涉仪传感模型的理论分析

本文提出了一种用发光二极管作为光源、用自聚焦透镜构成法布里-珀罗腔的双法布里-珀罗干涉仪光纤位移传感模型.根据部分相干光的干涉理论,得到了这个传感模型输出光强与两个法布里一珀罗干涉仪腔长之差的函数曲线.     

Twin-hollow-core optical fibres

Twin-hollow-core microstructured optical fibres have been fabricated and characterised for the first time. The fibre cladding structure results in guidance by the inhibited coupling mechanism, in which there is a low overlap between the core modes and surrounding structure. This results in minimal interaction between the modes of each core in the transmission bands of the fibre and hence minimal coupling between the cores. It is shown that light is able to couple between the cores via coupling to cladding struts in the high loss wavelength bands.     

Thermally stable optical fibre Bragg grating wavelength reference

The inherent temperature dependence of optical fibre Bragg gratings is caused mainly by the positive thermo-optic effect of the fibre core material, and it results in an increase of Bragg wavelength with temperature. Special mounting techniques may be designed in order to compensate this thermo-optic effect by counter-acting effects: decreasing mechanical strain, as well as a decreasing effective refractive index for the guided light wave by evanescent field interaction with a liquid of negative thermo-optic effect. Because of the non-linear interaction characteristics, exact temperature compensation is obtained for a certain temperature, which depends on the design parameters. Such stabilised fibre Bragg gratings find application as wavelength references in Bragg grating sensor networks.     

实现微位移测量的非本征法布里-珀罗干涉型光纤传感器

从光纤耦合和多光束干涉的原理出发,建立了非本征型法布里_珀罗干涉仪光纤传感器的理论模型,得到了用光谱法进行绝对距离测量的公式。设计出了传感器探头的结构,并搭建了系统。用LED作为宽带光源所得到的反射光谱可用于实际样品的微位移测量。实验结果表明,该传感器理论模型的数值模拟结果与实验结果是一致的。对实验数据进行了误差分析,所得到的测量精度可达到1μm。     

光纤外差干涉位移传感器性能的提高

利用半导体激光器 (LD)、光隔离器、光纤定向耦合器、自聚焦透镜等组成双路光纤斐索型干涉仪。采用三角波电流调制 ,上、下边沿拍频信号差动鉴相的方法 ,提高了测量灵敏度和位移响应速度 ,增大了测量范围 ;利用辅助干涉仪检测系统的相位漂移 ,并对LD发光波长进行反馈控制 ,提高了系统的稳定性 ,实现了大测量范围、高分辨率、高精度位移测量。     

大量程激光位移传感器的成像系统设计

为了解决目前国内自主研发的激光位移传感器基准工作距离短和测量范围小的问题,设计了一种适用于远距离测量的大量程激光位移传感器成像光学系统。基于激光三角测量原理,结合具体使用要求计算了大量程激光位移传感器的性能指标和成像光学系统的设计参数。选择5片式透镜结构作为系统的初始结构,利用光学设计软件对大量程激光位移传感器成像光学系统进行了仿真,完成了系统优化和性能分析,实现了基准工作距离为1 000 mm、量程为±500 mm、分辨率为0.4 mm的大量程激光位移传感器成像系统设计。结果表明,在测量范围±500 mm内,系统均可以满足成像质量要求。该激光位移传感器成像系统具有工作距离远、测量量程大、结构简单的特点,可满足1 000 mm远距离处大量程范围的测量使用要求。     

A single hop architecture exploiting cooperative beamforming for wireless sensor networks

In this paper, we propose a single hop architecture for a cooperative wireless sensor network and analyze the attained distributed beamforming gain performance using the theory of random arrays. All nodes in the system transmit a single carrier such that the signals add up constructively towards the direction of the fusion center. The potential directive beamforming gains are investigated for different sensor network densities which are expressed as the number of nodes per carrier wavelength squared. The multiple access capability of the sensor network is achieved by employing an on-off keying orthogonal signaling technique, which is usually employed in atmospheric optical systems. Finally, we investigate the average loss in directivity gain when the received signal from each sensor node follows a Ricean distribution. The results show that high directive gains can be achieved in practical wireless sensor networks using simple sensor nodes.     

Fully automatic system for the coupling alignment of optical fibres

To realize the low-loss connection of two optical fibres intended as a transmission medium for optical signals, very tight tolerances have to be observed on account of the small geometrical dimensions involved. The present work describes a fully automatic system for the alignment of optical fibres in thex-y planes relative to a light source, which has only a single intensity peak, so that maximum optical power is launched into the fibre. The light source can be, for instance, the radiating end of a fibre, a semi-conductor laser or a light-emitting diode. The optical power coupled into the fibre serves as the control signal. Three precision displacement stages driven by stepping motors serve to align the fibres. Various sequential control algorithms for optimal coupling are investigated with reference to theory. Two algorithms are tested with the aid of a computer with reference to the alignment accuracy and speed requirements which have to be met and the one shown by theoretical simulation to be the more favourable is selected for technical realization. The resulting system was used for numerous alignment operations for the coupling of two graded-index fibres. The alignment time is below 1 s and the coupling efficiency compared with manual coupling alignment efficiency (= 100%) is above 99%, corresponding to an additional loss of <0.05 dB.