Gain-clamped two-stage L-band EDFA with a FBG laser in second stage

A gain-clamped two-stage L-band EDFA is demonstrated by simply incorporating two different FBGs on both side of EDF in the second stage. It forms a FBG laser at 1560 nm to clamp the gain in the system. The gain is clamped at about 16.5 dB with gain variation of less than 1.0 dB at dynamic range up to −10 dBm. A flat gain is obtained over 30 nm of wavelength range from 1568 to 1598 nm with a gain variation of less than 1.1 dB. At the flat region, the noise figure varies from 5.0 to 5.8 dB, which is slightly higher compared to those of unclamped amplifier. The advantage of this technique is that the FBG laser does not disturb the WDM signals in the flat gain region.     

Gain-clamping techniques in two-stage double-pass L-band EDFA

Two designs of long-wavelength band erbium-doped fiber amplifier (L-band EDFA) for gain clamping in double-pass systems are demonstrated and compared. The first design is based on ring laser technique where a backward amplified spontaneous emission (ASE) from the second stage is routed into the feedback loop to create an oscillating laser for gain clamping. The gain is clamped at 18.6 d B from -40 to -80 dBm with a gain variation of less than ±0.1 dB and a noise figure of less than 6 dB. Another scheme is based on partial reflection of ASE into the EDFA, which is demonstrated using a narrowband fiber Bragg grating. This scheme achieves a good gain clamping characteristic up to -12 dBm of input signal power with a gain variation of less than ±0.3 dB from a clamped gain of 22 dB. The noise figure of a 1580 nm signal is maintained below 5 dB in this amplifier since this scheme is not based on lasing mechanism. The latter scheme is also expected to be free from the relaxation oscillation problem.     

Gain and noise figure improvements in double-pass S-band EDFA

Double-pass short-wavelength band erbium-doped fiber amplifier (S-band EDFA) with enhanced gain and noise figure characteristics is demonstrated. It uses a broadband fiber Bragg grating (FBG) operating in conventional-band (C-band) region to reduce the C-band amplified spontaneous emission (ASE) in the amplifier system and thus increases the population inversion in the S-band region. The small signal gain is increased by about 2.7 dB for 1500 nm signal at pump power of 103 mW, compared with that of the conventional double-pass amplifier without the FBG. The corresponding noise figure is also improved by 0.5 dB.     

Hybrid flat gain C-band optical amplifier with Zr-based erbium-doped fiber and semiconductor optical amplifier

An efficient gain-flattened C-band optical amplifier is demonstrated using a hybrid configuration with a Zirconia-based Erbium-doped fibre (Zr-EDF) and a semiconductor optical amplifier (SOA). The amplifier utilizes a two-stage structure with a midway isolator to improve flat gain characteristic and reduce noise figure. At input signal power of −30 dBm, a flat gain of 28 dB is obtained from wavelength region of 1530 to 1560 nm with gain variation of less than 4 dB. The noise figure is maintained below 11 dB at the flat-gain region. This amplifier has the potential to be used in the high channel count dense wavelength division multiplexing system due to its simplicity and compact design.     

Low noise double pass L-band erbium-doped fiber amplifier

A new double pass long wavelength band erbium-doped fiber amplifier with enhanced noise figure characteristics is demonstrated. The noise figure is improved by about 2.6 dB with the incorporation of broadband conventional-band fiber Bragg grating (FBG) in between the two segments of erbium-doped fiber. By incorporating both the pre-amplifier and the FBG, the noise figure is further improved, which varies from 4.0 to 5.0 dB in the flat gain region from 1570 to 1600 nm. The gain varies from 32.0 to 33.4 dB within this region. The new amplifier with high gain and low noise figure can be useful as an inline amplifier in a wavelength division multiplexing transmission system.     

Low noise gain-clamped L-band erbium-doped fiber amplifier by utilizing fiber Bragg grating

A novel gain-clamped long wavelength band (L-band) erbium-doped fiber amplifier (EDFA) is proposedand experimented by using a fiber Bragg grating (FBG) at the input end of the amplifier. This designprovides a good gain clamping and decreases noise effectively. It uses two sections of erbium-doped fiber(EDF) pumped by a 1480-nm laser diode (LD) for higher efficiency and lower noise figure (NF). The gainis clamped at 23 dB with a variation of 0.5 dB from input signal power of -30 to -8 dBm for 1589 nm andNF below 5 dB is obtained. At the longer wavelength in L-band higher gain is also obtained and the gainis clamped at 16 dB for 1614 nm effectively. Because the FBG injects a portion of backward amplifiedspontaneous emission (ASE) back into the system, the gain enhances 5 dB with inputting small signal.     

Dynamic-performance characterization of C-band EDFA using ASE-power peak-selective feedback gain-clamping

We propose and demonstrate a C-band Erbium-doped fiber amplifier (EDFA) using amplified spontaneous emission (ASE) power peaking-selective and feedback to achieve highly stabilized and wide dynamic range gain clamping performances. The gain of 16.20 ± 0.13 dB is obtained with the input signal power dynamic range of 30 dB and the maximum noise figure (NF) was 6.6 dB with the input signal power from −35 to −10 dBm. To investigate the gain variation for the probe signals, we applied a saturation tone signal to simulate 16-channel DWDM signals as it is added (dropped) into (from) EDFA. The gain variation of the proposed scheme at a appropriate ring-cavity loss (VOA = 5 dB) is less than 0.13 dB for the input signal power from −35 to −5 dBm and wavelength from 1530 to 1564 nm.     

High gain double-pass L-band EDFA with dispersion compensation as feedback loop

We demonstrate an efficient double-pass L-band erbium-doped fiber amplifier (EDFA) incorporating chirped fiber Bragg grating (CFBG). The amplifier structure exploits the characteristics of CFBG to reflect the amplified signal back into the gain medium, filter out the recycled forward amplified spontaneous emission and block the residual 1480 nm pump power. The amplifier configuration has high gain and low noise figures as compared to double-pass EDFA using broadband mirror. The demonstrated amplifier has gain of more than 48 dB and low noise figure of less than 4 dB at low input signal power of −40 dBm.     

Effect of injection of C-band ASE on L-band erbium-doped fiber amplifier

The effect of injecting conventional band (C-band) amplified spontaneous emission on the performance of long-wavelength band erbium-doped fiber amplifier (L-band EDFA) is demonstrated. It uses a circulator and broadband fiber Bragg grating (FBG) to route C-band ASE from a C-band EDFA. Injection of a small amount of ASE (attenuation of 20 dB or above) improves the small signal gain with a negligible noise figure penalty compared to that of an amplifier without the ASE injection. A maximum gain improvement of 3.5 dB is obtained at an attenuation of 20 dB. At very large amounts of ASE injection (attenuation of 0 dB), the gain of the amplifier is clamped at 15.2 dB from ?40 to ?10 dBm with a gain variation of less than 0.3 dB. The saturation power is also increased from ?8 dBm (for without ASE injection) to 2 dBm (VOA=0 dB) with a slight noise figure penalty. These results show that the ASE injection technique can be used either for gain improvement or for gain clamping in L-band EDFA.     

The L-band EDFA of high clamped gain and low noise figure implemented using fiber Bragg grating and double-pass method

The L-band erbium-doped fiber amplifier (EDFA) of low noise figure and high clamped-gain using gain-clamped and double-pass configuration is presented in this paper. A total of five different configurations of EDFAs by reflection scheme with single forward pumping schemes are examined and compared here. Among these configurations, we first find the configuration of 1480-nm pumped L-band EDFA with optimum gain and noise figure value. To further minimize the gain variation, a fiber Bragg grating (FBG) with 1615-nm center wavelength and 1-nm bandwidth is determined and added in double-pass L-band EDFA. The gain variation and maximum noise figure of EDFA while channel dropping is investigated. As the number of channel dropping from 32 to 4, the L-band type-A EDFA keep the variation of gain within 2.9 dB and the maximum noise figure below 5 dB with each channel’s input power of −23 dBm.     

Low Noise-figure Miniature Erbium-doped Fibre Amplifier using Uncooled Pump Laser

A miniature-size erbium doped fibre amplifier (MS-EDFA) is constructed with a saturation power of 17.0 dBm and low noise figure of 5.2 dB using an uncooled pump laser. The MS-EDFA has achieved low polarization dependent gain, large signal gain and small signal gain of 0.05 dB, 15 dB (at Pin = +2 dBm) and 42 dB (at Pin = −30 dBm), respectively, with negligible temperature dependent gain. The dimension of MS-EDFA is only twice than a typical credit card.     

Gain-flattened erbium-doped fiber amplifier with flexible selective band for optical networks

Erbium-doped fiber amplifier with flat gain over 30 nm bandwidth is demonstrated using flexible selective band methods. The band optical amplifier was designed to cater 44 wavelength division multiplexing channels which were separated into bands of 4 nm. Without using any gain flattening filter, the gain of optical amplifier was maintained at 19 dB with a maximum gain variation of less than 1.6 dB even though the input signal power was varied from −19 to −6 dBm. The amplifier was able to maintain 1 dB gain flatness with 83% chance for any selective bands of 4 nm within the wavelength range from 1530 to 1565 nm. This feature is very attractive to support band optical networks.     

Experimental and theoretical studies on a double-pass C-band bismuth-based erbium-doped fiber amplifier

Performance of a Bismuth-based Erbium-doped fiber amplifier is experimentally and theoretically investigated using 1480 nm pumping with double-pass scheme. In the theoretical analysis, the rate and power propagation equations are solved to examine the optimum length for the C-band operation as well as the gain and noise figure characteristics. The calculated small signal gain is 38 dB with gain variation of less than 3 dB. The measured gain is 4 dB lower due to spurious reflections which were ignored in the theoretical analysis. At input signal power of 0 dBm, a gain of 14.5 dB is obtained experimentally with gain variation of less than 1 dB within the wavelength region from 1530 to 1565 nm. The noise figure is less than 12 dB within this region.     

Investigation of the optical gain and noise figure for multi-channel amplification in EDFA under optimized pump condition

We present the results of an investigation of optical gain and noise figure for simultaneous multi-channel amplification of an erbium doped fibre amplifier (EDFA) under optimized pump condition. Different pump configurations with varying input signal levels show interesting features on gain flatness. In the experiment, population inversion along the fibre length which determines the gain-spectra and noise characteristics of the amplifier is adjusted through optimized fibre length and injected pump power in order to minimize the gain-tilt at C-band. It is observed that bi-directional pumping manifests the best combination of low noise and high gain of EDFA which are useful as in-line repeaters in WDM network. We obtain 30 ± 1.5 dB intrinsically flat small signal gain from 1538 nm to 1558 nm band of wavelength with noise figure <4 dB for 16-channel simultaneous amplification in a single stage EDFA without gain flattening filter.     

High gain S-band semiconductors optical amplifier with double-pass configuration

In this paper we propose and demonstrate a double-pass configuration of a compact high gain short wavelength (S-) band amplifier based on a semiconductor optical amplifier (SOA) operating from 1480 to 1520 nm. The proposed system provides gain value of 31.07 dB at a signal power level of −40 dBm taken at 1500 nm. The measure gain profile of the double-pass configuration over different power levels and at different signal wavelengths outperforms that of the single-pass configuration. The noise figure of both configurations averages out to 10 dB. This system provides a good alternative as a high-gain and compact amplifier in the S-band region.     

A gain-flattened L-band dual-core erbium-doped fibre amplifier

An L-band erbium-doped fibre amplifier consisting of a length of dual-core fibre is reported. It has a flat gain from 1565 to 1615 nm with a maximum gain variation of 0.6 dB, and noise figure less than 3.9 dB.     

Limitation in the intrinsic method of EDFA gain optimization for 32 × 40 Gbit/s WDM systems

The gain flattening of the erbium doped fiber amplifier (EDFA) is one of the most important aspects in the EDFA which the gain is wavelength dependent. For the first time the limitation of EDFA gain optimizing for a 32-channel wavelength division multiplexing (WDM) systems is investigated and reported in this paper. In a 32-channel WDM system the most favorable flatness gain achieved was 23.16 ± 1.51 dB with an average noise figure of 5.70 dB. This outcome proposes that the method does not achieve a uniform spectral gain in a 32-channel WDM system that incorporates a bandwidth of around 25 nm. Based on the simulation results the intrinsic optimization of EDFA causes the poor SNR and peak signal power with great variation over a transmission distance of 480 km single mode fiber.     

Gain-clamping in two-stage L-band EDFA using an unwanted backward ase from second stage

A gain clamping technique for the long wavelength band erbium-doped fiber amplifier (L-band EDFA) is presented. It uses two circulators and a broad band fiber Bragg grating to route wasted backward C-band ASE from the second stage and launch it back into the input end of the first stage of a two-stage amplifier. The two-stage L-band EDFA has shown a small signal gain improvement of 5.7 dB compared to a single-stage amplifier with a slight noise figure degradation. By utilizing the wasted backward ASE, a L-band gain-clamped EDFA with high gain can be realized. Compared to the unclamped case, this gain-clamping technique is effective in reducing the total gain variation as small as 0.3 dB.     

High-gain and low-noise-figure erbium-doped fiber amplifier employing dual stage quadruple pass technique

A high-gain and low-noise-figure (NF) erbium-doped fiber amplifier (EDFA) was demonstrated utilizing a new technique called the dual-stage quadruple pass (DSQP) with filters. An efficient amplification occurs at the signal wavelength of 1550 nm when it travels along the DSQP amplifier. The highest gain of 62.56 dB with a low noise figure of 3.98 dB was achieved for an input signal power of −50 dBm and pump powers of 10 and 165mW in the second and first stage amplifiers respectively.     

Utilization of stimulated Raman Scattering as secondary pump on hybrid remotely-pump l-band Raman/erbium-doped fiber amplifier

An L-band remotely-pumped erbium-doped fiber amplifier incorporating a secondary pumping scheme utilizing stimulated Raman Scattering (SRS) was demonstrated. 1423 nm Raman laser was employed to generate SRS which became the secondary pump source. The amplifier displayed excellent gain of up to 27.3 dB at 1570 nm for −30 dBm input. Noise figures were also kept to a minimum, with the highest figure measured at 11 dB which was influenced by imperfection of the C/L coupler utilized in this architecture. Overall transmission performance was measured as well and demonstrated an encouraging outcome with gain as high as 24 dB while the noise figure was maintained at about 11 dB. The L-band signal amplification was also contributed by the stimulated Raman scattering along the transmission fiber. The outcome of this study emphasized the feasibility of secondary pumping scheme using SRS in L-band gain enhancement.