钙钛矿型LaxSr1－xNi1－yCoyO3光电催化活性研究

用甘氨酸-硝酸盐燃烧合成法, 制备La_xSr_1－xNi_1－yCo_yO₃复合氧化物的陶瓷粉末, 对钙钛矿氧化物进行了XRD结构分析. 在通氧或不通氧下测试氧还原和氧析出的循环伏安曲线. 结果表明: 该氧电极具有双功能催化特性, 但不完全可逆. 利用汞灯作为激发光源, 进行几种水溶性染料和五种混合染料光解实验, 利用紫外-可见、红外以及人工神经网络光度法研究La_xSr_1－xNi_1－yCo_yO₃的催化性能. 结果表明: La_xSr_1－xNi_1－yCo_yO₃ (x＝0.7, 0.9, 1; y＝0.3, 0.75)复合氧化物都具有较强光催化特性; La_xSr_1－xNi_1－yCo_yO₃的光催化活性高于La_xSr_1－xNiO₃, 这与B位离子(Ni^2—, Co^2－)的电子构型有关; Co^2＋的加入可使La_xSr_1－xNiO₃的光催化活性有所提高.     

空气中合成固溶体荧光粉Ba2(Zn, Mg)Si2O7:Ce3+,Eu2+,Eu3+及其发光特性

采用高温固相法在空气中合成了Ba_1.97-yZn_1-xMg_xSi₂O₇:0.03Eu,yCe³⁺系列荧光粉。分别采用X-射线衍射和荧光光谱对所合成荧光粉的物相和发光性质进行了表征。在紫外光330~360 nm激发下,固溶体荧光粉Ba_1.97-yZn_1-xMg_xSi₂O₇:0.03Eu的发射光谱在350~725 nm范围内呈现多谱峰发射,360和500 nm处有强的宽带发射属于Eu²⁺离子的4f⁶5d¹-4f⁷跃迁,590~725 nm红光区窄带谱源于Eu³⁺的⁵D₀-⁷F_J (J=1,2,3,4)跃迁,这表明,在空气气氛中,部分Eu³⁺在Ba_1.97-yZn_1-xMg_xSi₂O₇基质中被还原成了Eu²⁺;当x=0.1时,荧光粉Ba_1.97Zn_0.9Mg_0.1Si₂O₇:0.03Eu的绿色发光最强,表明Eu³⁺被还原成Eu²⁺离子的程度最大。当共掺入Ce³⁺离子后,形成Ba_1.97-yZn_0.9Mg_0.1Si₂O₇:0.03Eu,yCe³⁺荧光粉体系,其发光随着Ce³⁺离子浓度的增大由蓝绿区经白光区到达橙红区;发现名义组成为Ba_1.96Zn_0.9Mg_0.1Si₂O₇:0.01Ce³⁺,0.03Eu的荧光粉的色坐标为(0.323,0.311),接近理想白光,是一种有潜在应用价值的白光荧光粉。讨论了稀土离子在Ba₂Zn_0.9Mg_0.1Si₂O₇基质中的能量传递与发光机理。     

CeCl3-CdCl2-H2O和CeCl3-CdCl2-HCl-H2O的相平衡

测定了三元系CeCl₃-CdCl₂-H₂O (25 ℃)和四元系CeCl₃-CdCl₂-HCl(～8.4％)-H₂O(25 ℃) 的相平衡溶度数据,绘制了相应的溶度图.该三元系是由5个固相区CdCl₂&;#8226;2.5H₂O(原始盐)、CdCl₂&;#8226;H₂O(原始盐)、6CdCl₂&;#8226;CeCl₃&;#8226;14H₂O、4CdCl₂&;#8226;CeCl₃&;#8226;12H₂O、CeCl₃&;#8226;7H₂O(原始盐)组成的复杂体系.该四元系是由5个固相区CdCl₂&;#8226;H₂O(原始盐)、9CdCl₂&;#8226;CeCl₃&;#8226;19H₂O、6CdCl₂&;#8226;CeCl₃&;#8226;14H₂O、4CdCl₂&;#8226;CeCl₃&;#8226;12H₂O、CeCl₃&;#8226;7H₂O(原始盐)组成的复杂体系.其中6CdCl₂&;#8226;CeCl₃&;#8226;14H₂O在该三元系是介稳化合物.9CdCl₂&;#8226;CeCl₃&;#8226;19H₂O 、6CdCl₂&;#8226;CeCl₃&;#8226;14H₂O和4CdCl₂&;#8226;CeCl₃&;#8226;12H₂O用X射线粉末衍射及TG-DTG和DSC等方法进行了研究,并对X射线粉末衍射进行了指标化.     

纳米钙钛矿LaxSr1-xFe1-yCoyO3复合氧化物的制备和表征

用甘氨酸-硝酸盐燃烧合成法，制备La_xSr_1-xFe_1-yCo_yO₃复合氧化物的陶瓷粉末，对该钙钛矿型氧化物进行了XRD、IR、紫外漫反射光谱及循环伏安曲线分析。结果表明：该复合氧化物粉体平均晶粒为15.3～29.8 nm,为立方和正交晶系。该氧电极具有双功能催化特性，但不完全可逆。对水溶液染料进行光解实验，利用紫外-可见、人工神经网络光度法研究La_xSr_1-xFe_1-yCo_yO₃的催化性能。结果表明：CO²⁺的加入可使La_xSr_1-xFeO₃的光催化活性有所提高，B位离子(Fe³⁺，CO²⁺)改变与加入，使La_xSr_1-xFe_1-yCo_yO₃(x=0.7，0.3；y=0.3，0.9，1)光催化活性高于La_xSr_1-xFeO₃。同时，对5种染料进行紫外光解，在0.75 h，脱色率大于91%，并为动力学一级反应。     

层状O2结构锂锰氧化物Li0.60[MgxCoyMn1-x-y]O2的制备及结构表征

本文采用离子交换法分别制备了双复合锂锰氧化物Li_0.60[Mg_xMn_1-x]O₂(0.05 ≤ x ≤ 0.15)和三复合锂锰氧化物Li_0.60[Mg_xCo_yMn_1-x-y]O₂(x=0.05，0.05 ≤      

La-Ce对PbTiO3陶瓷气相扩渗生成La2Ti6O15CeTi21O38的陶瓷材料及其电性能

报道了采用气相法对PbTiO₃陶瓷扩渗La-Ce混合稀土元素的研究. 在气相扩渗过程中, La, Ce与PbTiO₃陶瓷组元发生了复杂反应,生成了稀土化合物La₂Ti₆O₁₅和CeTi₂₁O₃₈, 制备出未见报道的La₂Ti₆O₁₅-CeTi₂₁O₃₈-PbTiO₃陶瓷材料, 经测试其导电性能发生了十分显著的变化. La₂Ti₆O₁₅-CeTi₂₁O₃₈-PbTiO₃陶瓷材料的室温电阻率从2.0 ×10¹⁰ W·m下降为0.248 W·m,而且随着温度的变化, 晶粒电阻呈现明显的PTCR效应,而晶界电阻随着温度的升高,呈急剧连续降低状态,总电阻的变化规律与晶界电阻的变化相一致, 试样总电阻的PTCR效应已不存在, 近趋导体. 经XPS测试分析, 进一步证实了La₂Ti₆O₁₅-CeTi₂₁O₃₈-PbTiO₃陶瓷材料中铅、钛等元素均有变价, 因而导致了La₂Ti₆O₁₅-CeTi₂₁O₃₈-PbTiO₃陶瓷材料电阻率的降低, 测试结果还首次给出了La₂Ti₆O₁₅-CeTi₂₁O₃₈-PbTiO₃陶瓷材料中各元素结合能位置的峰值. TG-DTA热分析表明La₂Ti₆O₁₅-CeTi₂₁O₃₈-PbTiO₃陶瓷材料具有较好的高温热稳定性.     

o-ZrW1.6Mo0.4O8·H2O正交相的合成与表征

The precursor ZrW_1.6Mo_0.4O₇(OH)₂(H₂O)₂ was characterized by IR and XRD methods. δ′-ZrW_1.6Mo_0.4O₈ was prepared by careful controlling the annealing conditions from the precursor and was determined to have the formula as o-ZrW_1.6Mo_0.4O₈·H₂O by TG-DSC, IR, and XRD methods. The relation between o-ZrW_1.6Mo_0.4O₈·H₂O and o-ZrW_1.6Mo_0.4O₈ was discussed through variable temperature XRD patterns. Further more, the mechanism of the precursor dehydration was suggested.     

298.15 K Li2B4O7-MgCl2-H2O体系热力学性质的电动势法测定及离子相互作用模型的研究

测定了298.15 K下, 无液接电池Li-ISE│Li₂B₄O₇ (m_A)(aq.), MgCl₂(m_B)(aq.)│AgCl/Ag的电动势, 利用测定结果计算了Li₂B₄O₇-MgCl₂-H₂O体系离子强度在0.05～3 mol•kg^－1范围内, 不同MgCl₂离子强度分数的溶液中LiCl的平均活度系数, 并给出了其随离子强度I, B₄O₇^2－和Mg^2＋浓度的变化规律. 结合以往关于该体系和Li₂B₄O₇-LiCl-H₂O, Li₂B₄O₇-H₂O体系的等压研究结果, 用迭代和多元线性回归方法对Li^＋-Mg^2＋-Cl^－-B₄O₇^2－-H₂O体系的离子相互作用模型进行了研究. 具体方法为考虑了该体系在不同的总硼浓度范围H₃BO₃, B(OH)₄^－, B₃O₃(OH)₄^－和B₄O₅(OH)₄^2－四种含硼化合物的存在以及各硼化合物间的化学平衡, 以修正了的Pitzer渗透系数方程和活度系数方程为基础, 对该体系的等压法和电动势法研究结果进行最小二乘拟合, 拟合的标准偏差为0.0167, 用该模型计算的该体系的渗透系数、活度系数与实验值基本一致.     

由大环配体[As4W40O140]28-与NiII形成的新型超大杂多化合物

在pH = 4.0的水溶液中, NiCl₂·6H₂O, NH₄Cl与Na₂₇[NaAs₄W₄₀O₁₄₀]·60H₂O反应, 得到了新的杂多砷钨酸盐(NH₄)₂₀[Na₂(H₂O)₂Ni(H₂O)₅{Ni(H₂O)}₂As₄W₄₀O₁₄₀]·61H₂O单晶, 用X射线单晶衍射法及元素分析确定了其结构, 晶体属三斜晶系, P¹空间群; 其晶胞参数为: a = 1.33135(18), b = 1.9722(3), c = 3.6430(5) nm, α = 78.010(2)°, β = 82.145(2)°, γ = 74.385(2)°, V = 8.978(2) nm3, Z = 2, R1 = 0.0512, wR2 = 0.0684 (I > 2σ). 在聚阴离子[Na₂(H₂O)₂Ni(H₂O)₅{Ni(H₂O)}₂As₄W₄₀O₁₄₀]^20-中, 2个Ni²⁺和2个Na⁺分占大环配体[As₄W₄₀O₁₄₀]^28-内的4个S2空位, 每个S2位提供4个O_d向金属离子配位, 2个Ni²⁺的配位数为6, 两个Na⁺的配位数分别为5和6, 另一个Ni²⁺处于环外, 与[As₄W₄₀O₁₄₀]^28-的一个端基氧(O_d)桥连成键, 其配位数为6.     

Ce1－xNdxO2－δ固溶体的电子顺磁共振谱和阻抗谱的研究

利用溶胶-凝胶方法在800 ℃焙烧10 h后, 合成了固溶体Ce_1－xNd_xO_2－δ (x＝0.05～0.55), X射线衍射(XRD)测试表明固溶体已经形成立方萤石结构; 电子顺磁共振谱(EPR)研究表明在固溶体Ce_1－xNd_xO_2－δ中随着掺杂量x的增大, Ce^3＋离子含量减少, 说明掺杂Nd^3＋离子可以抑制Ce^4＋的还原; 交流阻抗谱的测量表明固溶体Ce_0.9Nd_0.1O_2－d 具有离子导电特性, 600和700 ℃时的电导率分别为4.25×10^－3和1.12×10^－2 S•cm^－1, 活化能为0.68 eV.     

二氧化碳共聚物型聚氨酯反应动力学的研究

利用傅立叶变换红外光谱（FMIR）研究了二氧化碳（CO2）共聚物果碳酸亚丙酯合成聚氨酯的反应动力学，讨论了不同温度的初期反应速率、反应常数和反应的活化能。该工作为选择合适的反应条件提供了依据，在理论上和实践上都有重要意义。     

多代超支化水性聚氨酯的合成及表征

以甲苯-2,4-二异氰酸酯(TDI)、二羟甲基丙酸(DMPA)和二乙醇胺(DEOA)为原料通过偶合单体反应法合成了一系列不同代数的超支化水性聚氨酯(HPU),通过红外光谱(FT-IR)和核磁共振波谱（NMR）对其结构进行了表征,利用三检测器的凝胶渗透色谱(GPC3)测定各代产品分子量,采用热重分析仪(TG)和示差扫描量热仪(DSC)对各代HPU及类似化学组成的线性水性聚氨酯(LPU)的热性能进行测试分析对比,结果表明,合成各代HPU产率最高可达91%;TG分析表明各代数HPU与LPU具有相近的初始分解温度,大约在200℃左右,但各代HPU与LPU的分解历程明显不同;DSC结果表明各代HPU产品的玻璃化温度(Tg)明显高于LPU,同时随着代数增高,Tg逐步由115.2℃升高到150.3℃;对比各代HPU掺杂涂膜发现,随代数的增加,光泽度和硬度明显提高。     

Control of hard segment size in polyurethane formation

In general, segmented polyurethane elastomers are prepared by reacting an isocyanate-capped polyol prepolymer with a short-chain diol chain extender, yielding an elastomer with hard segments of uniform size. However, the hard segment size will not be uniform if the polyurethane polymer is prepared by forming the hard segment first, followed by soft segment formation. Because the mechanical properties of polyurethane elastomers depend on the relative ratio of the hard to soft segments as well as the effectiveness of the hard segment as a physical crosslinker, the control of the size distribution of the hard segment is a key factor in designing polyurethane elastomers. It was found that reaction conditions can affect the size distribution of hard segments derived from an aliphatic diisocyanate with differential reactivity between the two isocyanate groups. Lower reaction temperatures and simultaneous mixing of all reactants gave the preferred size distribution of hard segments. © 1995 John Wiley & Sons, Inc.     

巯基-烯光点击反应辅助合成多官能度蓖麻油基聚氨酯丙烯酸酯

研究巯基-烯光点击反应辅助合成多官能度蓖麻油基聚氨酯丙烯酸酯。首先通过光引发的巯基-烯点击反应,于蓖麻油分子上引入巯基乙醇,形成多羟基化合物,然后加入丙烯酸羟丙酯与异佛尔酮二异氰酸酯,以物质的量为1:1反应得到端异氰酸酯丙烯酸酯,最终得到蓖麻油基聚氨酯丙烯酸酯。通过调节羟基含量可以得到不同官能度的丙烯酸酯。采用红外光谱、核磁氢谱、热重分析等手段表征其结构和性能,并测试了合成的聚氨酯丙烯酸脂的吸水率、附着力等性能,同时考察了它的热稳定性。结果表明, 在紫外光照射下,巯基和不饱和双键之间发生了加成反应;该聚合物的固化膜性能得到提高,尤其是硬度和热稳定性。由本文快速合成方法得到的树脂性能良好,具有较好的应用前景,扩大了巯基-烯光点击反应在高性能UV固化材料方面的应用范围。     

聚氨酯改性不饱和聚酯树脂的反应动力学

通过差示扫描量热法(DSC)和傅里叶红外光谱(FT-IR)分析,探讨了聚氨酯改性不饱和聚酯树脂(UPR)体系反应特征及固化反应动力学。结果表明:体系中聚氨酯网络的形成远快于UPR网络的形成。UPR和聚氨酯改性UPR体系的表观活化能分别为58.0 kJ/mol和64.8 kJ/mol,改性后体系的活化能并无较大变化;反应的级数分别为0.90和0.91。     

丙烯酸聚醚聚氨酯合成反应中的氢键效应及其反应动力学研究

以红外光谱法研究了丙烯酸聚醚聚氨酯合成反应(其中有氢键效应存在)及其反应动力学。结果表明:由于丙烯酸聚氨酯分子链结构中含有-CO-O-;-NH-和-O-三种主要极性基因,导致在反应中存在明显的氢键变化。在第一步聚氨酯预聚体合成中,氢键距离R随反应进行而逐渐减小,反映出-NHCO-O-结构增加,聚集加强,氢键作用加强,并趋向稳定;其中不同结构聚氨酯预聚体氢键距离R不同:R_(MDI)>R_(HDI)>R_(TDP),链段结构中有序程度依次降低。在第二步丙烯酸聚氨酯合成中,存在明显键效应,其链段结构中有序程度较原来预聚体稳定或略有下降。在二步合成反应过程中,1/1-P_(NCO)和t之间呈现很好的线性关系,表明这两步合成均属二级反学动力学。其区别在于第一步反应速率常数(k_1)较第二步反应速率常数(k_2)小一个数量级。     

Synthesis and characterization of bismaleimides derived from polyurethanes

A series of novel bismaleimides (BMIs) were prepared from maleic anhydride and polyurethane prepolymers based on MDI (4,4′-diphenylmethane diisocyanate) and polyether and polyester diols with various chain lengths. All the BMIs were characterized by IR, ¹H-NMR, and elemental analysis. DSC studies indicated that the thermal polymerization of the BMIs could be carried out in the temperature range of 102–245°C, and that curing behavior was significantly affected by the molecular weight of the BMIs. The crosslinked BMI elastomers showed good mechanical properties and much better thermal stability than that of the traditional polyurethane elastomers. The glass transition temperatures, mechanical, and dynamic mechanical properties were dependent on the types of polyols used and the resultant crosslink densities due to various chain lengths of the BMIs. © 1994 John Wiley & Sons, Inc.     

3D Carbon Foam Supported Edge-Rich N-Doped MoS2 Nanoflakes for Enhanced Electrocatalytic Hydrogen Evolution

Molybdenum disulfide (MoS₂) is one of the most promising alternatives to the Pt-based electrocatalysts for the hydrogen evolution reaction (HER). However, its performance is currently limited by insufficient active edge sites and poor electron transport. Hence, enormous efforts have been devoted to constructing more active edge sites and improving conductivity to obtain enhanced electrocatalytic performance. Herein, the 3D carbon foam (denoted as CF) supported edge-rich N-doped MoS₂ nanoflakes were successfully fabricated by using the commercially available polyurethane foam (PU) as the 3D substrate and PMo₁₂O₄₀³⁻ clusters (denoted as PMo₁₂) as the Mo source through redox polymerization, followed by sulfurization. Owing to the uniform distribution of nanoscale Mo sources and 3D carbon foam substrate, the as-prepared MoS₂-CF composite possessed well-exposed active edge sites and enhanced electrical conductivity. Systematic investigation demonstrated that the MoS₂-CF composite showed high HER performance with a low overpotential of 92 mV in 1.0 m KOH and 155 mV in 0.5 m H₂SO₄ at a current density of 10 mA cm⁻². This work offers a new pathway for the rational design of MoS₂-based HER electrocatalysts.     

The influence of furanyl monomer on the self‐healing polyurethanes by reverse Diels‐Alder cross‐link

In this work, several furanyl diols with amide, imide, or amine groups were synthesized, each diol was subsequently polymerized with 4,4′‐dicyclohexylmethane diisocyanate and polytetramethylenene ether glycol to prepare polyurethanes. Bis(4‐maleimidophenyl) methane was then added as a cross‐linker to give self‐healing polyurethanes. DSC and DMA analysis were used to measure the DA/rDA temperature of these polyurethanes with different chemical structures. It was demonstrated that the polyurethane prepared from amide furanyl diol had the highest DA/rDA temperature, followed with the order of amide > imide > amine. This expands the versatility of monomers that have different self‐healing activity, which is expected to have the application for preparing various polyurethane coatings.     

Thermally driven self-healing PEDOT conductive films relying on reversible and multiple Diels–Alder interaction

Thermally healing capability of cracks and defects is important and urgent for the safe operation and life extending of electric materials and devices. Here, by the combination of thermally driven reversible Diels–Alder (DA) interaction and in-situ chemical oxidative polymerization of 3,4-ethylenedioxythiophene (EDOT), a series of intrinsically conductive poly(3,4-ethylenedioxythiophene) (PEDOT)/DA composites possess intrinsically self-healing property under low-temperature (reverse DA reaction at 100°C; DA crosslinking at 60°C) stimulus were achieved. The crosslinking DA bonding reactions are multiple from the co-existence of pre-synthesized macromolecular polyurethane attached DA units (PU-DA) and 2,4-hexadiyne-1,6-diol (DADOL) in the films. PU-DA involved in the polymerization process of EDOT to endow PEDOT with outstanding solution-processability, uniform film making, and structural self-healing capability, while DADOL was added to enhance the cross bonding between polymer chains. This work will accelerate the research and application development of intrinsically self-healing conducting polymers for commercial capacitors, antistatic coatings, implantable, printable electronics, and so on.