Li2O-TiO2-SiO2-P2O5和Li2O-TiO2-Al2O3-P2O5体系锂离子固体电解质的制备及性能研究

一些具有NASICON型网格结构的固体电解质具有高的电导率和好的稳定性,NASICON的意思是Na Super Ionic Conductor[1]。当NaZr2(PO4)3中P5 被Si4 部分取代时便可以得到具有NASICON结构的Na1 xZr2SixP3-xO12体系,其具有高的钠离子电导率。然而有相同结构的Li1 xZr2SixP3-xO12体系的离子电导率却很低,这是因为Li 半径太小,而NASICON三维网格结构的离子通道太大,两者不匹配而使电导率下降[2]。但当LiZr2(PO4)3中Zr4 被离子半径小些的Ti4 取代,所得LiTi2(PO4)3的通道就与Li 半径相匹配,适合于锂离子的迁移,从而使其电导率…     

The effect of PO<Subscript>2,5</Subscript> and AlO<Subscript>1,5</Subscript> additions on structural changes and crystallization behavior of SiO<Subscript>2</Subscript>-TiO<Subscript>2</Subscript> sol-gel derived glasses and thin films

SiO₂-TiO₂-PO_2,5 (STP) and SiO₂-TiO₂-AlO_1,5 (STA) glasses were prepared by sol-gel processing. Their infrared absorption spectra (IR), differential thermal analysis curves (DTA) and X-ray diffraction patterns (XRD) have been recorded. In the SiO₂-TiO₂ system, the chemical homogeneity of the sol-gel glass could be evaluated by the relative concentration of Si-O-Ti heterocondensation comparing to Si-O-Si homocondensation. For the STA system, a gradual decrease of the Si-O-Ti/Si-O-Si band ratio (based on IR spectra) with the addition of Al₂O₃ is observed, with the simultaneous formation of Si-O-Al and Ti-O-Al bounds, i.e Al₃ ⁺ ions are dissolved in the SiO₂-TiO₂ glass matrix and do not promote glass-in-glass phase-separation in the composition range of 0–15 mol% AlO_1.5. In the STP system, on the other hand, P=O bond IR stretch in the ternary glasses indicates that P=O free PO₂O_2/2 ⁻ tetrahedra are formed, rather than the double bonded POO_3/2 tetrahedra that usually occur in binary SiO₂-P₂O₅ glasses. It can be concluded that SiO₂-TiO₂-P₂O₅ glass separates into a SiO₂-rich phase and a TiO₂(P₂O₅)-rich phase. During heat-treatment in STA system only anatase precipitates, even at T ~ 1,000 °C, while in for STP, anatase (TiO₂) or (TiO)₂P₂O₇ (TOP) crystals precipitate at ~600 °C, depending on the P₂O₅ concentration. The major crystal phase, cristobalite, precipitated at ~1,000 °C and at ~1,200 °C, the P-containing phase melts.     

The Ternary System Li2O-Al2O3-B2O3: Compounds and Phase Relations

The ternary system Li₂O-Al₂O₃-B₂O₃ is reinvestigated with solid-state reaction and X-ray powder diffraction technique to clarify some long-standing uncertainties. The phase relations are constructed based on the phase identifications of 51 ternary samples. Six ternary compounds, Li₂AlB₅O₁₀, LiAlB₂O₅, Li₃AlB₂O₆, Li₂AlBO₄, LiAl₇B₄O₁₇ and a compound with a composition close to 0.66Li₂O·0.06Al₂O₃·0.28B₂O₃, are observed or confirmed in this system, and the thermal stability of these ternary compounds is also discussed on the basis of DTA experimental results.     

Synthesis and characterization of inorganic solid electrolytes of Li2O-SiO2-P2O5 and Li2O-TiO2-SiO2-P2O5 systems

The lithium-ion-conducting inorganic solid electrolytes in the oxide systems Li₂O-SiO₂-P₂O₅ and Li₂O-TiO₂-SiO₂-P₂O₅ were prepared by the solid-state reaction, and the electrolyte pellet made by cold-pressing method had diameter of 13 mm and was about 1 mm thick. Phase identification and surface morphology of the products were carried out by X-ray diffraction and scanning electron microscopy. Ionic conductivity of the pellets was investigated through ac impedance. The results show that the adding of other cations can improve the ionic conductivity of the solid electrolyte, and the sintering temperature and duration can influence the ionic conductivity. The maximum ionic conductivity in the samples is 9.9 × 10⁻⁴ S/cm in the Li₂O-TiO₂-SiO₂-P₂O₅ system. Original Russian Text ? W. Li, M. Wang, Z.H. Li, X.F. Shang, H. Wang, Y.W. Wang, Y.B. Xu, 2007, published in Elektrokhimiya, 2007, Vol. 43, No. 11, pp. 1341–1345.     

Preparation and radioluminescent characteristics of Li<Subscript>2</Subscript>O-B<Subscript>2</Subscript>O<Subscript>3</Subscript>-P<Subscript>2</Subscript>O<Subscript>5</Subscript>-CaF<Subscript>2</Subscript> glasses doped with Ce(III) and Gd(III)

A method has been developed for the preparation of homogeneous moisture-resistant glasses with the composition Li₂O-B₂O₃-P₂O₅-CaF₂ : Ce³⁺-Gd³⁺. Energy transfer from Gd³⁺ to Ce³⁺ was noted in a study of the radioluminescence spectra of these samples using ²⁴¹Am as the excitation source (60 keV). The decay time of the Ce³⁺ radioluminescence in the glasses obtained was 20-25 ns.     

Trends in the cation distribution in the structures of the compounds forming in the Ln<Subscript>2</Subscript>O<Subscript>3</Subscript>-GeO<Subscript>2</Subscript>-P<Subscript>2</Subscript>O<Subscript>5</Subscript> systems

The cationic networks in the structures of the initial oxides and all binary and ternary compounds forming in the Ln₂O₃-GeO₂-P₂O₅ systems have been studied. In the phase diagrams of the Nd₂O₃-GeO₂-P₂O₅ and Er2O₃-GeO₂-P₂O₅ systems, the regions of the structural influence of individual compounds with topologically identical cationic networks—anisotropic (A), combined (C), and isotropic (I)—are united into common areas. The A: C: I area ratio is 1: 1: 1 in the neodymium system and 1.7: 1: 3.4 in the erbium system.     

Li4Ti5O12/(Ag+C)电极材料的固相合成及电化学性能

以Li₂CO₃,TiO₂为原料,葡萄糖为碳源,采用固相煅烧工艺合成了亚微米级的Li₄Ti₅O₁₂/C复合负极材料。并将之与AgNO₃复合,采用固相方法制备出了Ag表面修饰的Li₄Ti₅O₁₂/(Ag+C)复合材料。采用XRD、SEM和TEM测试方法对材料的微结构进行了表征。结果表明,C的存在对Ag单质在Li₄Ti₅O₁₂/C颗粒表面的大量形成起到了积极的促进作用,从而很大程度地提高了Li₄Ti₅O₁₂/C的电导率,因此有效地改善了其电化学性能。在1C倍率下,Li₄Ti₅O₁₂/(Ag+C)复合材料的首次放电容量达到了164 mAh·g^-1。     

A study of the formation of LiNbO3 in the system Li2CO3Nb2O5

The formation process of LiNbO₃ in the system Li₂CO₃Nb₂O₅ was discussed from the results of non-isothermal or isothermal TG experiments and X-ray analysis. The mixture Li₂CO₃ and Nb₂O₅ in mole ratios of 1:3, 1:1 or 3:1 was heated at a rate of 5°C min^?1 or at various temperatures fixed in the range 475 to 677°C. If the system has a composition of Li₂CO₃ + 3Nb₂O₅ or 3Li₂CO₃ + Nb₂O₅, the reaction between Li₂CO₃ and Nb₂O₅ proceeds with CO₂ evolution to form LiNbO₃ at ca. 300–600°C, but Nb₂O₅ or Li₂CO₃ remains unreacted. A composition of Li₂CO₃ + Nb₂O₅ gives LiNbO₃ at 300–700°C. The diffusion of Li₂O through the layer of LiNbO₃ is rate-controlling with an activation energy of 51 kcal mol^?1. The reaction between LiNbO₃ and Nb₂O₅ gives LiNb₃O₈ at 600–700°C. At 700–800°C, a slight formation of Li₃NbO₄ occurs by the reaction between LiNbO₃ and Li₂O at the outer surface of LiNbO₃ and the Li₂O component of Li₃NbO₄ diffuses toward the boundary of the LiNb₃O₈ layer through the LiNbO₃ layer. The single phase of LiNbO₃ is formed above 850°C.     

Crystallization of spodumene-diopside in the las glass ceramics with CaO and MgO addition

Crystallization, morphology and mechanical properties of a spodumene-diopside glass ceramics with adding different amount of CaO and MgO in Li₂O-Al₂O₃-2SiO₂ were investigated. With CaO and MgO addition, the crystallization temperature (T _p) decreased, the value of Avrami constant (n) decreased from 3.2±0.3 to 1.4±0.2, the activation energy (E) increased from 299±3 kJ mol⁻¹ to 537±5 kJ mol⁻¹. The crystalline phases precipitated were h-quartz solid solution, β-spodumene and diopside. The mechanism of crystallization of the glass ceramics changed from bulk crystallization to surface crystallization. The grain sizes and thermal expansion coefficients increased while flexural strength and fracture toughness of the glass-ceramics increased first, and then decreased. The mechanical properties were correlated with crystallization and morphology of glass ceramics.     

Investigations of potassium-cerium phosphates rich in P2O5

In the ternary system Ce₂O₃-K₂O-P₂O₅, the partial system Ce(PO₃)₃-KPO₃-P₂O₅ was examined by means of differential thermal analysis and powder X-ray diffraction. The phase compositions of the products obtained on various thermal treatments were investigated. The phase diagram of the system Ce(PO₃)₃-KPO₃-P₂O₅ is suggested.

---

Zusammenfassung Mittels DTA und Röntgendiffraktion wurde im ternären System Ce₂O₃-K₂O-P₂O₅ das Teilsystem Ce(PO₃)₃-KPO₃-P₂O₅ untersucht. Die Phasenzusammensetzungen der durch verschiedene Erhitzungsvorgänge erhaltenen Produkte wurden untersucht und ein Phasendiagramm für das System Ce(PO₃)₃-KPO₃-P₂O₅ erstellt.

     

Preparation and characterization of Li4/3Ti5/3O4/Ag composite prepared by sol-gel technique

The powders of Li_4/3Ti_5/3O₄/Ag composite were prepared by sol-gel technique. Structural identification, surface morphology and electrochemical properties of the powders were studied by X-ray diffraction, scanning electron microscopy and galvanostatic charge-discharge experiments. The results show that Li_4/3Ti_5/3O₄/Ag composite derived from sol-gel is a composite of Li_4/3Ti_5/3O₄ and silver. Li_4/3Ti_5/3O₄/Ag composite shows higher specific capacity, higher columbic efficiency and lower polarization than Li_4/3Ti_5/3O₄. The addition of silver greatly improves the cycleability of Li_4/3Ti_5/3O₄, especially at higher charge-discharge rate.     

Preparation,structure and properties of silicate-phosphate glasses obtained by means of sol-gel method

Gels, densified amorphous materials and thin layers in SiO₂-P₂O₅, SiO₂-P₂O₅-Al₂O₃ and SiO₂-P₂O₅-Na₂O systems were obtained from alcohol solutions. Detailed DTA, XRD and FTIR investigations were carried out for dried gels and heat-treated samples. It has been found, among others, that the addition of aluminium to the silicate-phosphate glasses eliminates the doubly bonded oxygen (P=O) and leads to the formation of a continuous framework connected with [SiO₄], [PO₄] and [AlO₄] tetrahedra.There were measured the chemical and electrical properties of glasses covered with silicatephosphate gel layers. It has been found that the chemical resistance of the covered glasses is higher than that of the basic, sodium-calcium-silicate glass. Moreover, the silicate-phosphate layers modify the surface electrical conduction of the basic glasses. The layers of systems SiO₂-P₂O₅ and SiO₂-P₂O₅-Al₂O₃ show the electrical conduction considerable higher than the basic glass. The layers containing sodium, depending on its concentration, behave similarly to the basic glass or show lower electrical conductivity.     

纳米Fe3O4-TiO2靶向光动力疗法对肝癌细胞的杀伤效应

光动力疗法(PDT)作为一种迅速发展的传统替代疗法,在抗癌治疗中显示出巨大的潜力.为增强靶向性和提高光催化杀伤效率,本研究设计了一种新型光敏剂Fe₃O₄-TiO₂磁性纳米粒.在不同外磁场下,考察其在可见光和紫外光激发下对肝癌细胞的杀伤效应.同时利用流式细胞术检测纳米Fe₃O₄-TiO₂对肝癌细胞凋亡率、细胞周期和线粒体膜电位的影响.根据纳米Fe₃O₄-TiO₂和肝癌细胞的作用方式探讨其抗癌机制.结果表明,可见光激发纳米Fe₃O₄-TiO₂可以杀伤癌细胞,且其杀伤效率与紫外光激发下无明显差别.此外,Fe₃O₄-TiO₂比TiO₂具有更高的细胞摄取率,从而使其具有更高的选择性和光催化杀伤效率.其作用机制是光催化纳米Fe₃O₄-TiO₂产生活性氧ROS抑制癌细胞,然后通过阻滞细胞周期G₀/G₁期,降低线粒体膜电位,线粒体去极化,最终诱导细胞凋亡.     

Complete oxidation of ethanol over vanadium based catalysts

V2O5/γ-Al2O3-TiO2 catalysts were prepared by the mixing sol-gel and co-impregnation method. The performance of the catalysts for complete oxidation of ethanol was performed in a conventional fixed-bed quartz reactor. And the effects of support, preparation methods and vanadium content have been investigated. The results showed that 5% V2O5 catalyst supported on γ-Al2O3-TiO2 possessed the best ethanol conversion under the considered temperature. This may be ascribed to the highly dispersible active component, mutual function between the active component and the carriers. The nature of the best performance for 5%V/γ-Al2O3-TiO2 catalyst may be related to the high V4+ amounts on the surface. And the surface V4+ species may play an important role in the formation of active site for the total ethanol oxidation.     

Synthesis of nanopowders of pentoxides Ta2y Nb2(1−y)O5

The processes of production of high purity nanopowders of niobium and tantalum pentoxide Ta_2y Nb_2(1–y)O₅ with a low content of fluorine and Nb₂O₅ in low-temperature polymorph were studied. Ceramic samples were prepared from a charge of solid solutions LiTa _y Nb_1–y O₃ and Li _x Na_1–x Ta _y Nb_1–y O₃ synthesized using coprecipitated pentoxide Ta_2y Nb_2(1–y)O₅. Therewith for solid solutions LixNa_1–x Ta _y Nb_1–y O₃ significantly larger values of high dielectric constant and ionic conductivity were achieved compared to the solid solutions obtained by using a mechanical mixture of Ta₂O₅ and Nb₂O₅. This converts solid solutions LixNa_1–x Ta _y Nb_1–y O₃ from acoustoelectronic and piezoelectric type of materials into the capacitor and ion-conductive type of solid materials.     

Structural Study of Li1+x−yNb1−x−3yTix+4yO3 Solid Solutions

The structures of Li_1+x−yNb_1−x−3yTi_x+4yO₃ solid solutions within the so-called M-phase field in the Li₂O-Nb₂O₅-TiO₂ system were investigated using high-resolution transmission electron, microscope (HRTEM) and single-crystal X-ray diffraction. The results demonstrated that the phase field is not a solid solution but rather a homologous series of commensurate intergrowth structures with LiNbO₃-type (LN) slabs separated by single [Ti₂O₃]²⁺ corundum-type layers. The thickness of the LN slab decreases with increasing Ti-content from ∼55 to 3 atomic layers in the metastable H-Li₂Ti₃O₇ end-member. The LN slabs accommodate a wide range of Ti⁴⁺/Nb⁵⁺ substitution, and for a given homolog the distribution of Ti and Nb is not uniform across the slab. A single-crystal X-ray diffraction study of a structure composed of nine-layer LN slabs revealed preferential segregation of Ti to the slab surfaces which apparently provides partial compensation for the charge on the adjacent [Ti₂O₃]²⁺ corundum layers. The extra cations in phases with x>0 are accommodated through the formation of Li-rich Li₂MO₃-type layers in the middle of the LN slabs. The fraction of layers with extra cations increases with increasing Ti-content in the structure.     

Fluoroapatite - material for medicine,Growth, morphology and thermoanalytical properties

Fluoroapatite containing glass-ceramics were prepared from Li₂O-CaO-CaF₂-P₂O₅-SiO₂ system. The glass was melted at 1480°C for 1 h. The object of observation was the preparing crystal phase of fluoroapatite in amorphous glass matrix. The morphology of lithium disilicate glass-ceramics was studied by SEM. The crystal growth and thermal properties of fluoroapatite were studied by X-ray diffraction and DTA. The more the content of P₂O₅, the more the presence of fluoroapatite particles. SEM investigation clearly indicated the phase separation and formation of a primary crystalline phase of fluoroapatite in the studied glass-ceramics. DTA curves of the fluoroapatite samples exhibit exothermic effects in the temperature range 337-694°C depending on the composition of the materials. The position of exothermic peak for lithium disilicate on DTA curves moves with increasing specific surfacetowards lower temperatures which points on its preferential surface crystallization. As far as physical qualities are concerned, mainly color and gloss, the best qualities of all observed materials belong to glass-ceramics with 10% P₂O₅. This revised version was published online in July 2006 with corrections to the Cover Date.     

Mass spectrometric studies of lithium-containing oxides at high temperature

The sublimation and vaporization of various lithium containing oxides have been studied by high temperature mass spectrometry. The installed Knudsen cell apparatus gave some useful information about the vapor species, appearance potentials, partial pressures and heats of reactions involved. The investigated oxides are Li₂O, Li₂O-Al₂O₃, Li₂O-MoO₂ and Li₂O-SiO₂ systems. This paper mainly presents the most recent data for the Li₂O-SiO₂ system. A relationship for the decomposition reaction of ortho-Li₄SiO₄ was deduced. The heat of the reaction was determined by the third law method.The activity of the Li₂O component in the double oxides was estimated from the partial pressures of the vapor species. γ-LiAlO₂ and meta-Li₂SiO₃ showed fairly low activities in comparison with Li₂O oxide. The activity coefficients decreased with the Li₂O mole fraction in the lithium compounds.The heats of formation and atomization of LiO and Li₂O gaseous species were determined.     

Crystallization and microstructure of Li2O-Al2O3-SiO2 glass containing complex nucleating agent

The crystallization and microstructure of Li₂O-Al₂O₃-SiO₂ (LAS) glass ceramic with complex nucleating agents (TiO₂ + ZrO₂ + P₂O₅ +/or F⁻) are investigated by differential thermal analysis (DTA), X-ray diffraction (XRD) and scanning electron microscopy (SEM), and the effects of P₂O₅ and F⁻ on the crystallization of LAS glass are also analyzed. The introduction of both P₂O₅ and F⁻ promotes the crystallization of LAS glass by decreasing the crystallization temperature and adjusting the crystallization kinetic parameters, allows a direct formation of β-spodumene without the transformation of LiAl(SiO₃)₂ into β-spodumene and as a result, increases the crystal size and crystallinity of LAS glass ceramic.     

The preparation,characterization, and thermal behaviour of some lithium aluminum oxides: Li3AlO3 and Li5AlO4

The purpose of this research was to study the best conditions for the synthesis of the double oxides Li₅AlO₄ and Li₃AlO₃ in the solid state starting from the simple oxides, and to determine their heats of formation. Li₅AlO₄ was obtained from Li₂O₂ or Li₂O and γ-Al₂O₃ in a Li/Al molar ratio of 5∶1, and was characterized by X-ray methods. Lithium orthoaluminate, Li₃AlO₃, was obtained from Li₂O₂ and γ-Al₂O₃ in a molar ratio 3∶1. The postulated formula, Li₃AlO₃, was confirmed by chemical analysis. The temperature ranges in which the compounds are stable were established by the DTA method, and were found to be very limited for Li₃AlO₃ (400–430°) but greater for Li₅AlO₄ (440 — more than 600°). The heats of formation of Li₅AlO₄ and Li₃A10₃, also determined by means of the DTA method, were found to be ?552.3 ± 0.8 kcal/mole and ?416.8 ± 2 kcal/mole, respectively.