Simultaneous separation of organomercury species by nonaqueous capillary electrophoresis using methanol containing acetic acid and imidazole

A simple and rapid nonaqueous capillary electrophoresis method for simultaneous separation of four kinds of mercury species, namely inorganic mercury, methylmercury, ethylmercury, and phenylmercury, is reported. The effective mobilities of organomercury in aqueous and nonaqueous electrolytes were compared. Imidazole was confirmed not only as a co-ion for the separation but also as an online complexing reagent for mercury species. The optimum conditions for separation were achieved by using methanol solvent containing 0.15 M acetic acid and 15 mM imidazole as electrolyte. The sensitive detection of mercury species was accomplished at 191 nm.     

Determination of free amino acids in infant food by capillary zone electrophoresis with mass spectrometric detection

A method for the quantitative determination of free amino acids in infant food samples using capillary electrophoresis (CE) with electrospray-mass spectrometric (ESI-MS) detection is presented. According to the zwitterionic nature of the analytes, two different modes of separation as well as detection were tested; highly acidic carrier electrolytes combined with MS detection in the positive ion mode proved to be the optimum solution. Sensitivity as well as linearity of the method were sufficient to allow the analysis of all solutes of interest in a single run. In this way, free amino acids could be analyzed in a variety of infant food preparations without any sample pretreatment or derivatization step.     

Determination of carbohydrates by capillary electrophoresis with electrospray-mass spectrometric detection.

A method for the determination of underivatized carbohydrates using capillary electrophoresis (CE) with detection by electrospray ionization-mass spectrometry (ESI-MS) presented. Highly alkaline carrier electrolytes based on volatile organic bases like is diethylamine (DEA) combined with MS detection in the negativ-ion mode proved to be the optimum solution for the separation and detection of these analytes. Optimization of the carrier electrolyte composition has been performed with respect to its pH, ionic strength as well as the addition of an organic modifier. The influence of the DEA concentration in the sheath liquid on parameters like peak shapes or signal-to-noise (S/N) ratios was also investigated. Limits of detection (LOD) were in the range of 0.5-3.0 mgL(-1) and calibration was linear over an order of magnitude for almost all solutes investigated. Finally, the applicability of this method for the analysis of real samples was demonstrated with wine samples.     

Nonaqueous capillary electrophoresis-electrospray- mass spectrometry for the analysis of fluoxetine and its related compounds

The potential of nonaqueous capillary electrophoresis was investigated for the simultaneous separation of fluoxetine hydrochloride, its meta-isomer, and other related compounds. The resolution of these compounds was compared in aqueous and nonaqueous media. Baseline separation of the studied solutes required a buffer electrolyte solution composed of 25 mM ammonium acetate and 1 M acetic acid in acetonitrile, an applied voltage of 30 kV and a temperature of 20 degrees C. Selectivity was considerably affected by the nature of the solvent (water, methanol, and acetonitrile). Moreover, substituting acetate by formate in the background electrolyte resulted in migration time changes, which were attributed to an ion-pairing phenomenon. Finally, the method was successfully coupled on-line with electrospray ionization-mass spectrometry (ESI-MS) and allowed significant selectivity and sensitivity enhancement. The effect of ESI-MS parameters, such as nebulizing gas pressure, sheath liquid composition and flow rate, on resolution and method sensitivity was also discussed.     

Cyclodextrin-based nonaqueous electrokinetic chromatography with UV and mass spectrometric detection: application to the impurity profiling of amiodarone

The potential of nonaqueous electrokinetic chromatography (NAEKC) using cyclodextrins (CD) for the analysis of basic drugs and related compounds was evaluated. Both UV absorbance and mass spectrometric (MS) detection were employed. Addition of neutral CD to the NA background electrolyte did not significantly enhance the separation of a test mixture of basic drugs, and no change in selectivity was observed. In contrast, anionic single-isomer-sulfated CD strongly added to the selectivity of the NAEKC system inducing an improved resolution among the test compounds and increasing the migration time window. The applicability of the NAEKC system using anionic CD is demonstrated by the profiling of a sample of the drug amiodarone that had been stored for 1 year at room temperature. Amiodarone is poorly soluble in water. NAEKC-UV analysis indicated the presence of at least seven impurities in the amiodarone sample. In order to identify these compounds, the NAEKC system was coupled directly to electrospray ionization (ESI) ion-trap MS. The total of detected impurities increased to 12 due to the added sensitivity and selectivity of MS detection. Based on the acquired MS/MS data, three sample constituents could be identified as 'known' impurities (British Pharmacopoeia), whereas for three unknown impurities molecular structures could be proposed. Estimated limits of detection for amiodarone using the NAEKC method were 1 microg/mL with UV detection and 15 ng/mL with ESI-MS detection (full-scan). Based on relative responses, the impurity content of the stored drug substance was estimated to be 0.33 and 0.47% using NAEKC-UV and NAEKC-ESI-MS, respectively.     

Nonaqueous versus aqueous capillary electrophoresis of alpha-helical polypeptides: effect of secondary structure on separation selectivity

The CE separation of alpha-helical polypeptides composed of 14-31 amino acid residues has been investigated using aqueous and nonaqueous BGEs. The running buffers were optimized with respect to pH. Generally, higher separation selectivities were observed in nonaqueous electrolytes. This may be explained by a change in the secondary structure when changing from water to organic solvents. Circular dichroism spectra revealed a significant increase in helical structures in methanol-based buffers compared to aqueous buffers. This change in secondary structure of the polypeptides contributed primarily to the different separation selectivity observed in aqueous CE and NACE. For small oligopeptides of two to five amino acid residues no significant effect of the solvent was observed in some cases while in other cases a reversal of the migration order occurred when changing from aqueous to nonaqueous buffers. As these peptides cannot adopt secondary structures the effect may be attributed to a shift of the pKa values in organic solvents compared to water.     

NACE for the analysis of acrylamide in food

An NACE method was developed for the quantitative determination of acrylamide in processed food. The method is premised on the modification of the aqueous acid-base character of acrylamide in an organic solution. Acrylamide, which is a polar molecule in aqueous solution, in a low-pH environment in ACN acquires a proton, and thereby migrates under its own electrophoretic mobility in CE. Thus, nonaqueous separation of acrylamide was achieved by employing 30 mmol/L HClO(4) in ACN as the running electrolyte. The detection limit of the method for acrylamide was found as 0.041 mg/L using UV detection at 200 nm. The run-to-run and day-to-day precisions for the corrected peak areas were calculated as 1.65 and 3.90%, respectively. The applicability of the method has been demonstrated by analyzing acrylamide in the samples of potato chips and French fries. The method is simple, rapid, inexpensive, and widely applicable for the determination of acrylamide in food samples.     

Potential of formamide and N-methylformamide in nonaqueous capillary electrophoresis coupled to electrospray ionization mass spectrometry. Application to the analysis of beta-blockers

A nonaqueous capillary electrophoresis (NACE) method, coupled with either UV or electrospray mass spectrometry (ESI-MS), is described for the simultaneous analysis of seven beta-blockers. The same electrolyte, namely 25 mM ammonium formate and 1 M formic acid, was used with different investigated organic solvents. In addition to frequently used organic solvents such as methanol (MeOH) and acetonitrile (MeCN), formamide and its derivatives were investigated. Formamide (FA) and N-methylformamide (NMF) present several interesting physico-chemical properties, one of them being a high dielectric constant (e). Since FA and NMF possess a high UV cutoff, beta-blockers with an absorbance above 250 nm were selected as model compounds in order to compare NACE-UV and NACE-MS performances. FA and NMF showed different selectivity compared to water, MeOH or MeCN, and also demonstrated a higher efficiency in terms of the number of theoretical plates (especially NMF). To overcome their unfavorable optical properties, hyphenation with MS detection appears as a promising technique, thanks to its benefits in terms of selectivity, sensitivity and universality. The practical compatibility of FA and NMF with ESI-MS detection in combination with a sheath liquid configuration was demonstrated. In comparison to UV detection, sensitivity was increased, while a high efficiency was maintained. In addition, the low and stable generated currents observed were evidences for the successful hyphenation with ESI-MS. Hence, FA and NMF seemed to be promising alternatives in NACE-ESI-MS, either used as pure organic solvent or as a mixture with MeOH or MeCN.     

HPLC Separation of Aryldiamine Transformation Products using a Polar-Modified RP-C18 Column

A high-performance liquid chromatography–UV/VIS detection–electrospray ionization single quadrupole mass spectrometry (HPLC–UV/VIS–ESI-MS) method was developed to separate oxidative and photolytic degradation products of aryldiamines, that is, para-phenylenediamine and para-toluenediamine. The separation was performed on a polar modified reversed phase-C₁₈ column which provided superior chromatographic resolution compared to conventional columns. Gradient elution was used with the mobile phases of water and acetonitrile containing 10 mM ammonium acetate. Various compounds including aryldiamines, benzoquinones, aromatic nitro compounds, and azobenzenes were selected for an optimization of the ESI-MS operation and the chromatographic separation conditions. Highly linear calibrations (r² > 0.999) were achieved for a subset of 5 standard substances. Using analyte-specific UV detection wavelengths, limits of detection and limits of quantitation of these substances ranged from 3.0 to 7.0 µg L^?1 and from 10.0 to 23.3 µg L^?1, respectively. The analysis of aqueous solutions of para-toluenediamine photolysis products confirmed the performance of the method. Up to 28 chromatographic signals were recorded and the change of their peak heights during the transformation process was monitored for 24 hours. The identities of the compounds were ascertained by means of MS detection correlations between molecular features and the chromatographic retention of the compounds.     

Directed control of electroosmotic flow in nonaqueous electrolytes using poly(ethylene glycol) coated capillaries

Poly(ethylene glycol) (PEG)-coated capillaries exhibit unique properties in nonaqueous electrolytes. Immobilized PEG interacts significantly with different cations present in nonaqueous electrolytes. This can induce a positive surface charge on PEG-coated capillaries and results in an adjustable anodic electroosmotic flow (EOF) in nonaqueous electrolytes whereas a reduced cathodic EOF is observed in aqueous electrolytes. The EOF can reversibly be adjusted by the variation of the electrolyte constitution, namely the type of the solvent used and the nature and concentration of background cations. In methanol and especially in acetonitrile electrolytes the magnitude and also the direction of EOF is strongly dependent on the water content. Using different alkali metal cations, the EOF can be increased, reduced, or even reversed depending on the nature of the cation. The directed manipulation of EOF in methanolic electrolytes using PEG-coated capillaries was applied for optimization of nonaqueous capillary electrophoretic separations of acidic compounds with regard to reproducibility, resolution, and analysis time.     

Detection of hexamethonium-perchlorate association complexes using NACE-MS

Perchlorate (ClO(4) (+)) and other chlorine oxide anions were observed to complex weakly with hexamethonium (1,6-bis-(trimethylammonium)-hexane) in both aqueous and polar nonaqueous solvents. The resultant positively charged complexes were resolved by NACE using 2-propanol/acetone electrolytes prior to mass spectrometric detection using an Agilent(3D)CE system coupled to a Bruker Esquire 3000+ quadrupole IT mass detector. Using electrokinetic injection, the method detection limit for perchlorate in nonaqueous media was 10 microg/L. The isotope patterns due to the presence of (35)Cl and (37)Cl in complex mass spectra allowed for unambiguous identification of perchlorate, chlorate (ClO(3) (+)), chlorite (ClO(2) (+)), and chloride (Cl(+)) in photoreaction samples.     

Analysis of metal complex azo dyes by high-performance liquid chromatography/electrospray ionization mass spectrometry and multistage mass spectrometry

Five metal complex azo compounds were analyzed using negative-ion electrospray ionization mass spectrometry (ESI-MS). Mass spectra of all compounds yield intense peaks corresponding to [M - H](-) ions without any fragmentation, where M denotes the neutral compound with a proton as the counterion. Under collision induced dissociation (CID) conditions, structurally important fragment ions were studied using the ion trap analyzer with a multistage mass spectrometry (MS(n) facility. Synthesized compounds with (15)N atoms in the azo group facilitated the fragmentation pattern recognition. A reversed-phase high-performance liquid chromatography (HPLC) method using 5 mM ammonium acetate in 70% aqueous acetonitrile as mobile phase was developed making possible the separation of all complex compounds tested. The lower detection limits of the ESI-MS method are in the range 10-20 ng of each compound. The HPLC/ESI-MS method makes possible the monitoring of ligand exchange in aqueous solutions of metal complex azo dyes, and also investigation of the stabilities of the complexes in solution. Copyright 2000 John Wiley & Sons, Ltd.     

Use of the new, single-isomer, hexakis(2,3-diacetyl-6-O-sulfo)-alpha-cyclodextrin in acidic methanol background electrolytes for nonaqueous capillary electrophoretic enantiomer separations

The new, single-isomer, sulfated alpha-cyclodextrin, the sodium salt of hexakis(2,3-diacetyl-6-O-sulfo)-alpha-cyclodextrin (HxDAS), was used for the first time in acidic methanol background electrolytes (BGEs) to separate the enantiomers of weak base analytes by nonaqueous capillary electrophoresis (NACE). The concentration dependence of the effective mobilities and separation selectivities followed trends similar to those observed earlier in acidic methanol background electrolytes with heptakis(2,3-diacetyl-6-O-sulfo)-beta-cyclodextrin (HDAS) and octakis(2,3-diacetyl-6-O-sulfo)-gamma-cyclodextrin (ODAS). In general, interactions between the weak base analytes and HxDAS were weaker than with HDAS and ODAS. For some of the weak base analytes, separation selectivities observed in acidic aqueous and acidic methanol background electrolytes were complementary to each other, permitting the eventual separation of enantiomers that could not be achieved otherwise.     

Influence of solvent properties on separation and detection performance in non-aqueous capillary electrophoresis-mass spectrometry of basic analytes

The versatility of non-aqueous capillary electrophoresis (NACE) results mainly from the variety of physico-chemical properties of the different solvents. They provide solubility for a wide range of analytes, enable to control electrophoretic selectivity, but affect in some cases UV absorbance detection. The coupling of NACE to electrospray mass spectrometry (ESI-MS) allows to cope with the high UV cut-off of some CE relevant solvents (e.g., formamides). In this paper the pure organic solvents methanol, acetonitrile, dimethylsulfoxide, formamide, N-methylformamide and N,N-dimethylformamide are evaluated against water for the preparation of ammonium acetate electrolytes to separate the basic model substances 2-aminobenzimidazole, procaine, propranolol and quinine with NACE-MS. MS coupling is assisted with the sheath liquid water-isopropanol (1:4, v/v) with 0.1% formic acid. The goal of the paper is to assess the influence of the solvent on selectivity, separation speed, and peak efficiency for a given set of model compounds on a simple empirical basis. It should give the user an idea how the separation quality is changed when nothing but the running solvent is altered. The obtained efficiency results were discussed with respect to physico-chemical models described in literature (assuming longitudinal diffusion as the only source of band broadening), but no satisfying correlations with solvent properties could be traced. The feasibility of all six organic solvents for MS coupling was demonstrated and the influence of the separation solvent on the MS detection performance was compared. In the seven different solvents, the shortest run time was obtained with acetonitrile, the best peak resolution with the amphiprotic solvents (especially methanol) best peak efficiency with methanol and formamide, and the most sensitive ESI-MS detection with acetonitrile and methanol, but with only slight advantage to water.     

Determination of free cyanide and zinc cyanide complex by capillary electrophoresis

A capillary electrophoretic (CE) protocol was developed for the separation and quantification of free cyanide and zinc cyanide complex, two key species in gold cyanidation of zinc-bearing sulfidic ores. Several common carrier electrolytes were implemented in an indirect UV detection method. The effect of electric field strength, injection volume, concentration of electro-osmotic flow (EOF) modifier and UV-absorbing agent in background electrolyte (BGE) was examined while peak height, peak area and noise were considered for optimization. The best results were obtained using a BGE that contained 35 mM sodium chromate, 12 mM free cyanide and 0.45 mM hexamethonium bromide at pH 10.5. Free cyanide concentration was compared to that measured with the conventional silver nitrate titration method in solutions containing free cyanides and weak cyano-complexes. The developed CE protocol proved very robust in capturing the concentration of free cyanides (4% error) unlike the titration method which exhibited substantial sensitivity to the interfering weak cyano-complexes (38% error).     

Simultaneous determination of sildenafil, vardenafil and tadalafil as forbidden components in natural dietary supplements for male sexual potency by high-performance liquid chromatography-electrospray ionization mass spectrometry

A high-performance liquid chromatographic method coupled with ultraviolet detection and electrospray ionization mass spectrometry (HPLC-UV-ESI-MS) was developed for simultaneous determination of banned additives-sildenafil, vardenafil and tadalafil in dietary supplements for male sexual potency. The separation was achieved on a C18 column with acetonitrile and aqueous solution (20 mmol ammonium acetate, 0.2% formic acid) as mobile phase at a flow rate of I ml/min with a linear gradient program. UV detection was at 292 nm. Identification of drugs was accomplished using ESI-MS. Good linearity between response (peak area) and concentration was found over a concentration range of 0.8-80 microg/ml for sildenafil; 2.25-225 microg/ml for vardenafil; and 1.1-110 microg/ml for tadalafil, with regression coefficient is better than 0.999. The recovery of the method ranged from 93.3 to 106.1%, and the relative standard deviation varied from 2.0 to 5.6% (n = 6). The method has been successfully applied to the analysis of practical samples of natural dietary supplements.     

高效液相色谱-电喷雾质谱联用分析PPMP衍生化的壳寡糖

以1-(4-异丙基)苯基-3-甲基-5-吡唑啉酮(PPMP)为衍生化试剂在氨水介质中对壳寡糖链进行衍生化,衍生化产物用RP-HPLC分离和ESI-MS分析。结果表明在确定的衍生化条件下,PPMP和壳寡糖的衍生化产物主要为单分子衍生物,此单分子PPMP衍生物在ESI-MS的正负离子模式下均有较好的响应,并且在RP-HPLC柱上能够实现很好的分离。据此建立了PPMP柱前衍生HPLC/ESI-MS在线联用检测壳寡糖混合物组成的方法。该法可作为壳寡糖样品在质量控制、构效关系研究等方面的方法参考。     

硫酸沙丁胺醇的毛细管电泳非接触电导法检测

建立了毛细管电泳-非接触电导检测分离测定硫酸沙丁胺醇的分析方法。分别考察了分离介质、背景电解质及其浓度和pH、分离电压、进样时间、激发电压、激发频率等因素对实验结果的影响。在优化的实验条件(以15 mmol/L乳酸水溶液(pH 2.7)为电泳介质,10 kV下电动进样3 s,分离电压为10 kV,激发电压为60 V,激发频率为120 kHz)下,硫酸沙丁胺醇的检出限(信噪比为3)为1.92 mg/L,在9.60～48.0 mg/L质量浓度范围内有良好的线性关系(r=0.995),迁移时间的相对标准偏差(RSD)为2.7%。将该方法用于硫酸沙丁胺醇片和硫酸沙丁胺醇气雾剂中的硫酸沙丁胺醇含量的测定,加标回收率为90%～113%,检测结果与药厂的标示值相符合,为硫酸沙丁胺醇的检测提供了一种简便、快速、高灵敏的方法。关键词: 毛细管电泳;非接触电导检测法;硫酸沙丁胺醇;硫酸沙丁胺醇片;硫酸沙丁胺醇气雾剂     

Separation of living and dead polymers in synthetic polypeptide mixtures by nonaqueous capillary electrophoresis using differences in ionization states

The complexity in the mechanisms of polymerization of N-carboxyanhydrides requires the development of new analytical techniques able to separate mixtures of synthetic polypeptides. This work focuses on the separation of poly(N(epsilon)-trifluoroacetyl-L-lysine) (PTLL) mixtures by nonaqueous capillary electrophoresis (CE). The main goal of this work was to find electrophoretic conditions that permit the separation and the quantification of the dead polymer families that were previously identified in the samples. The influence of the pH of the electrolyte on the selectivity of the separation was carefully investigated. The mechanisms of separation of the PTTLs are discussed as a function of their ionization state. The separations obtained on a noncovalently coated capillary were compared with those obtained on a fused-silica capillary. Finally, using two different electrolytes, it is possible to quantify the three families of PTLLs, namely, the living PTLLs, the dead PTLLs with N-formyl end group and the dead PTLLs with a carboxylic end group. These results confirm the importance of CE for the separation of synthetic organic polymers in nonaqueous electrolytes.     

Nonaqueous capillary electrophoresis with laser-induced fluorescence detection: a case study of comparison with aqueous media

A novel method based on separation by nonaqueous capillary electrophoresis (NACE) combined with laser-induced fluorescence (LIF) detection was developed and compared with classic aqueous modes of electrophoresis in terms of resolution of solutes of interest and sensitivity of the fluorescence detection. Catecholamines derivatized with 4-chloro-7-nitro-2,1,3-benzoxadiazole (NBD-Cl) were chosen as test analytes for their subtle fluorescence properties. In aqueous systems, capillary zone electrophoresis (CZE) was not suitable for the analysis of test analytes due to complete fluorescence quenching of NBD-labeled catecholamines in neat aqueous buffer. The addition of micelles or microemulsion droplets into aqueous running buffer can dramatically improve the fluorescence response, and the enhancement seems to be comparable for micellar electrokinetic chromatography (MEKC) and microemulsion electrokinetic chromatography (MEEKC). As another alternative, NACE separation was advantageous when performing the analysis under the optimum separation condition of 20 mM sodium tetraborate, 20 mM sodium dodecyl sulfate (SDS), 0.1% (v/v) glacial acetic acid, 20% (v/v) acetonitrile (ACN) in methanol medium after derivatization in ACN/dimethyl sulfoxide (DMSO) (3:2, v/v) mixed aprotic solvents containing 20 mM ammonium acetate. Compared with derivatization and separation in aqueous media, NACE-LIF procedure was proved to be superior, providing high sensitivity and short migration time. Under respective optimum conditions, the NACE procedure offered the best fluorescence response with 5-24 folds enhancement for catecholamines compared to aqueous procedures. In addition, the mechanisms of derivatization and separation in nonaqueous media were elucidated in detail.