Direct electro-deposition of graphene from aqueous suspensions

We describe the direct electro-chemical reduction of graphene oxide to graphene from aqueous suspension by applying reduction voltages exceeding -1.0 to -1.2 V. The conductivity of the deposition medium is of crucial importance and only values between 4-25 mS cm(-1) result in deposition. Above 25 mS cm(-1) the suspension de-stabilises while conductivities below 4 mS cm(-1) do not show a measurable deposition rate. Furthermore, we show that deposition can be carried out over a wide pH region ranging from 1.5 to 12.5. The electro-deposition process is characterised in terms of electro-chemical methods including cyclic voltammetry, quartz crystal microbalance, impedance spectroscopy, constant amperometry and potentiometric titrations, while the deposits are analysed via Raman spectroscopy, infra-red spectroscopy, X-ray photoelectron spectroscopy and X-ray diffractometry. The determined oxygen contents are similar to those of chemically reduced graphene oxide, and the conductivity of the deposits was found to be ～20 S cm(-1).     

Efficient reduction of graphene oxide catalyzed by copper

We report that copper thin films deposited on top of graphene oxide (GO) serve as an effective catalyst to reduce GO sheets in a diluted hydrogen environment at high temperature. The reduced GO (rGO) sheets exhibit higher effective field-effect hole mobility, up to 80 cm(2) V(-1) s(-1), and lower sheet resistance (13 kΩ □(-1)) compared with those reduced by reported methods such as hydrazine and thermal annealing. Raman and XPS characterizations are addressed to study the reduction mechanism on graphene oxide underneath copper thin films. The level of reduction in rGO sheets is examined by Raman spectroscopy and it is well correlated with hole mobility values. The conductivity enhancement is attributed to the growth of the graphitic domain size. This method is not only suitable for reduction of single GO sheets but also applicable to lower the sheet resistance of Langmuir-Blodgett assembled GO films.     

Facile photoreduction of graphene oxide by an NAD(P)H model: Hantzsch 1,4-dihydropyridine

To make "clean" reduced GO sheets in high quality and in large scale, a natural reduced nicotinamine adenine dinucleotide NAD(P)H model, Hantzsch 1,4-dihydropyridine (HEH), is used as a mild organic photoreductant in this work. Benefiting from the intense absorption of HEH in the range of 300-420 nm, the graphene oxide (GO) can be readily reduced by HEH under UV light irradiation (λ > 320 nm) to afford single or few-layer reduced graphene oxide at room temperature. Studies on reduction extent reveal that both irradiation time and concentration ratio of HEH to GO are important for effective reduction of GO under UV light. The as-prepared photochemically reduced graphene oxide (PRGO) dispersion is stable without the need for any polymeric or surfactant stabilizers. Simply by extraction treatment, the "clean" PRGO sheets can be obtained in large quantities, and its conductivity approaches to 4680 S·m(-1) that is the highest value reported by photochemical approaches so far.     

Layer-by-Layer Self-Assembled Multilayer Films Composed of Graphene/Polyaniline Bilayers: High-Energy Electrode Materials for Supercapacitors

Multilayer assemblies of uniform ultrathin film electrodes with good electrical conductivity and very large surface areas were prepared for use as electrochemical capacitors. A layer-by-layer self-assembly approach was employed in an effort to improve the processability of highly conducting polyaniline (PANi) and chemically modified graphene. The electrochemical properties of the multilayer film (MF-) electrodes, including the sheet resistance, volumetric capacitance, and charge/discharge ratio, were determined by the morphological modification and the method used to reduce the graphene oxide (GO) to reduced graphene oxide (RGO) in the multilayer films. The PANi and GO concentrations could be modulated to control the morphology of the GO monolayer film in the multilayer assemblies. Optical ellipsometry was used to determine the thickness of the GO film in a single layer (1.32 nm), which agreed well with the literature value (～1.3 nm). Hydroiodic acid (HI), hydrazine, or pyrolysis were tested for the reduction of GO to RGO. HI was found to be the most efficient technique for reducing the GO to RGO in the multilayer assemblies while minimizing damage to the virgin state of the acid-doped PANi. Ultimately, the MF-electrode, which could be optimized by fine-tuning the nanostructure and selecting a suitable reduction method, exhibited an excellent volumetric capacitance, good cycling stability, and a rapid charge/discharge rate, which are required for supercapacitors. A MF-electrode composed of 15 PANi/RGO bilayers yielded a volumetric capacitance of 584 F/cm(3) at a current density of 3.0 A/cm(3). Although this value decreased exponentially as the current density increased, approaching a value of 170 F/cm(3) at 100 A/cm(3), this volumetric capacitance is one of the best yet reported for the other carbon-based materials. The intriguing features of the MF-electrodes composed of PANi/RGO multilayer films offer a new microdimensional design for high energy storage devices for use in small portable electronic devices.     

The reduction of graphene oxide by elemental copper and its application in the fabrication of graphene supercapacitor

In this work, graphene oxide (GO) was directly reduced by copper to reduced graphene oxide (RGO) and formed a highly uniform RGO film on copper foil or copper-modified titanium (Ti) substrate. The characterization of as-prepared RGO film by FTIR and XRD indicated that GO was partially reduced by copper while some oxygen-containing groups still remained. The conductivity of the RGO film was improved from 3.76?×?10³ to 2.98?×?10⁴ S/m after it was further electrochemically reduced due to the removal of additional oxygen groups. The graphene supercapacitor prepared with this method exhibited better performances in a neutral aqueous electrolyte compared with that reported for graphene electrodes prepared by other fabrication methods.     

One-step facile synthesis of poly(N-vinylcarbazole)-polypyrrole/graphene oxide nanocomposites: enhanced solubility,thermal stability and good electrical conductivity

Poly (N-vinylcarbazole)-polypyrrole/graphene oxide (PNVC-Ppy/GO) nanocomposites have been successfully prepared by one-step chemical oxidative polymerization using ferric chloride hexahydrate in the presence of dodecyl benzene sulfonic acid. The composite formation, morphology and the crystallinity of the composite have been characterized by FTIR spectroscopy, FESEM, and XRD, respectively. The incorporation of graphene oxide into the PNVC-Ppy matrix induces interaction between graphene oxide and PNVC-Ppy via hydrogen bonding and π–π* stacking. This π–π* stacking between the GO layers and PNVC-Ppy produces longer conjugation length leading to a higher solubility in organic solvents and enhanced electron mobility. The information of conjugation chain length and charge transfer capacity at the interface of the composite has been obtained from the Raman spectroscopy and photolumincience spectroscopy. The improved thermal stability and electrical d.c. conductivity (0.123?S/cm) of the resulting PNVC-Ppy/GO composite compared to the PNVC–Ppy copolymer (0.08?S/cm) is attributed to the incorporation of graphene oxide in the composite.     

Synthesis and characterization of bisulfonated poly(vinyl alcohol)/graphene oxide composite membranes with improved proton exchange capabilities

Composite membranes based on poly(vinyl alcohol) (PVA) and graphene oxide (GO) were prepared by solution-casting method to be used as proton exchange membranes (PEMs) in fuel cell (FC) applications. Bisulfonation was employed as a strategy to enhance the proton conductivity of these membranes. First, a direct sulfonation of the polymer matrix was accomplished by intra-sulfonation of the polymer matrix with propane sultone, followed by the inter-sulfonation of the polymer chains using sulfosuccinic acid (SSA) as a crosslinking agent. Furthermore, the addition of graphene oxide (GO) as inorganic filler was also evaluated to enhance the proton-conducting of the composite membranes. These membranes were fully characterized by scanning electron microscopy (SEM), Fourier transformed infrared spectroscopy (FTIR), thermogravimetric analysis (TGA) and tensile tests. Besides, the proton conductivity of these membranes in a fully hydrated state was also analyzed by electrochemical impedance spectroscopy (EIS). The effect of the intra- and inter-sulfonation of the polymer matrix on the structural, morphological, thermal and mechanical properties of the membranes were determined. Increasing the density of sulfonic acid groups in the membranes resulted in a trade-off between a better proton conductivity (improving from 0.26 to 1.00 mS/cm) and a decreased thermal and mechanical stability. In contrast, the incorporation of GO nanoparticles into the polymer matrix improved the thermal and mechanical stability of both bisulfonated composite membranes. The proton conductivity appreciably increased by the combination of bisulfonation and introduction of GO nanoparticles into the polymer matrix. The sPVA/30SSA/GO composite membrane exhibited a proton conductivity of 1.95 mS/cm at 25 °C. The combination of the GO nanoparticles with the chemical bisulfonation approach of PVA allows thus assembling promising proton exchange membrane candidates for fuel cell applications.     

Effect of humidity on the conductivity of graphite oxide during its photoreduction

The influence of humidity on the conductivity of graphite oxide (GO) films has been considered. Graphite oxide films of a 200–500 nm thickness become conductors to have a conductivity of 10^?6 to 10^?2 S/cm when humidity increases from 30 to 100%. Film morphology varies during the course of water diffusion. Ultraviolet light-mediated reduction of GO decreases the sensitivity to humidity until its complete disappearance.     

Segregated reduced graphene oxide polymer composite as a high performance electromagnetic interference shield

Herein, we report the synthesis of a graphene/polymer composite via a facile and straightforward approach for electromagnetic interference (EMI) shielding applications. Polystyrene (PS) beads were added in graphene oxide (GO)/water solution followed by the addition of hydroiodic acid (HI) for in situ reduction of GO. The composite solution (rGO/PS) was filtered, hot compressed and tested for EMI shielding and dielectric measurements. A 2-mm thick segregated rGO/PS sample with 10 wt% filler loading delivered a high EMI shielding effectiveness (SE) of 29.7 dB and an AC electrical conductivity of 21.8 S m^?1, which is well above the commercial requirement for EMI shielding applications. For comparison with the segregated rGO/PS composite, a control polymer composite sample utilizing a thermally reduced graphene oxide was synthesized by following a conventional coagulation approach. The as-synthesized conventional rGO/PS yield an EMI SE of 14.2 dB and electrical conductivity of 12.5 S m^?1. The high EMI shielding of segregated rGO/PS is attributed to the better filler-to-filler contact among graphene layers surrounded by PS beads and also to the better reduction and preservation of graphene structure during reduction process that makes the low temperature chemically reduced segregated rGO/PS approach a viable route compared to high temperature thermally reduced conventional rGO/PS approach.     

Double laminated reduced graphene/Cu_2S/reduced graphene/graphene oxide nanofilms and their photoelectrochemical properties

In this work,an efficient photocatalytic material was prepared directly on Indium tin oxide(ITO)glass substrates by fabricating Cu_2 S and graphene oxide onto graphene for photoelectrochemical(PEC) water splitting.The double laminated reduced graphene/Cu_2S/reduced graphene/graphene oxide(RG/Cu_2S/RG/GO) nanofilms were characterized,and an enhanced photoelectrochemical response in the visible region was discovered.The photocurrent density of the nanofilms for PEC water splitting was measured to be up to 1.98 m A/cm~2,which could be ascribed to the followings:(i) a higher efficiency of light-harvesting because of GO coupling with Cu_2 S that could broaden the absorbing solar spectrum and enhance the light utilization efficiency;(ii) a stepwise structure of band-edge levels in the Cu_2S/GO electrode was constructed;(iii) double laminated electron accelerator(RG) was used in the Cu_2S/GO materials to get better electron-injecting efficiency.     

Preparation of porous polyimide/in‐situ reduced graphene oxide composite films for electromagnetic interference shielding

Herein we report an easy and efficient approach to prepare lightweight porous polyimide (PI)/reduced graphene oxide (RGO) composite films. First, porous poly (amic acid) (PAA)/graphene oxide (GO) composite films were prepared via non‐solvent induced phase separation (NIPS) process. Afterwards PAA was converted into PI through thermal imidization and simultaneously GO dispersed in PAA matrix was in situ thermally reduced to RGO. The GO undergoing the same thermal treatment process as thermal imidization was characterized with thermogravimetric analysis, Raman spectra, X‐ray photoelectron spectroscopy and X‐ray diffraction to demonstrate that GO was in situ reduced during thermal imidization process. The resultant porous PI/RGO composite film (500‐µm thickness), which was prepared from pristine PAA/GO composite with 8 wt% GO, exhibited effective electrical conductivity of 0.015 S m^?1 and excellent specific shielding efficiency value of 693 dB cm² g^?1. In addition, the thermal stability of the porous PI/RGO composite films was also dramatically enhanced. Compared with that of porous PI film, the 5% weight loss temperature of the composite film mentioned above was improved from 525°C to 538°C. Moreover, tensile test showed that the composite film mentioned above possessed a tensile strength of 6.97 MPa and Young's modulus of 545 MPa, respectively. Copyright © 2016 John Wiley & Sons, Ltd.     

Simultaneous functionalization and reduction of graphene oxide with polyetheramine and its electrically conductive epoxy nanocomposites

Simultaneous functionalization and reduction of graphene oxide(GO) is realized by refluxing of GO suspension with polyetheramine(D2000) followed by thermal treatment at 120 °C. Compared to GO, the D2000-treated GO(GOD2000) becomes hydrophobic, thermally stable and highly conductive with an electrical conductivity of 11 S/m, which is almost 8 orders of magnitude higher than that of GO. Due to the high conductivity and improved dispersion of GO-D2000, its epoxy nanocomposites exhibit a sharp transition from electrically insulating to conducting with a low percolation threshold of 0.71 vol%. With 3.6 wt% GO-D2000, the glass transition temperature of the epoxy nanocomposite is 27 K higher than that of neat epoxy.     

Capillary zone electrophoresis of graphene oxide and chemically converted graphene

The preparation of processable graphene oxide colloids called chemically converted graphene (CCG) involves the following steps: oxidation of graphite to form graphite oxide; exfoliation of graphite oxide to form graphene oxide (GO); and reduction of GO to form CCG. In this work, the exfoliation and reduction steps were monitored by capillary zone electrophoresis (CZE). CZE was performed in fused silica capillaries with UV absorbance at 230 nm (GO) and 270 nm (CCG) using 250 μM tetrapropylammonium hydroxide (pH 10.4). The results indicate that almost complete exfoliation of graphite oxide (0.05 wt%) and higher recovery of CCG were obtained by sonication at 50% power for more than 15 h. CZE is considered a valuable tool for the fractionation and analysis of GO nanoparticles and, hence, for the control of different steps in preparation of CCG.     

Electrochemistry-assisted microstructuring of reduced graphene oxide-based microarrays with adjustable electrical behavior

An electrochemistry-assisted microstructuring process is developed for fabricating well-aligned reduced graphene oxide (rGO)-based micropatterns on arbitrary substrates using a combined method of photolithography, electrochemical reduction and wet etching techniques. The dimension of special-shaped rGO microarrays localized in an insulating GO matrix is effectively adjusted by changing GO reduction time without multi-mask patterning. The increased conductivity of rGO micropatterns by several orders of magnitude is achieved by controlling GO thickness and reduction time. The electrochemical activity of rGO micropatterns as microarray electrodes is confirmed by using ferricyanide in aqueous solution as the redox probe. The present method could be a scalable technology to conventional photolithography for fabricating arbitrary rGO micropatterns in an insulating GO matrix for their potential applications in next generation electronic and electrochemical devices.     

Study on poly(imide-ethylene glycol) and graphene oxide-based hybrid proton exchange membrane

In this study, novel poly(imide-ethylene glycol) (PIEG) was prepared via polycondensation of ethylenediaminetetraacetic dianhydride, 4-aminophenyl sulfone, and poly(ethylene glycol) bis(amine). Later, thermally stable and mechanically robust undoped and acid-doped proton exchange membranes were prepared using the graphene oxide (GO) nanofiller. Field emission scanning electron microscope revealed a unique hexagonal imprinted morphology of the fractured surface. Increasing the GO content from 1 to 5 wt% increased tensile strength (59.7–65.9 MPa) and the modulus (20.3–23.9 GPa) of the undoped PIEG/GO series. Thermal properties of the undoped PIEG/GO 1–5 membranes were also higher, i.e., T₁₀ = 438–487°C. However, dop-PIEG/GO 1–5 membranes have a higher ion exchange capacity (IEC) of 2.4–2.9 mmol/g and proton conductivity 1.8–2.7 S cm^?1 (94% RH).     

Photochemical processes in graphene oxide films

Experimentally revealed features of thermal and photochemical deoxidation of graphene oxide (GO) in films are reported. A difference in mechanism between the photoreduction and thermal reduction of GO has been shown. The mechanism of photochemical deoxidation of graphene oxide has been rationalized using the concepts of molecular photochemistry. A new model of photoelimination of molecular oxygen from epoxy groups on graphene nanosheet has been proposed. The photoprocesses lead to growing of π-domains of graphene.     

Multicompartment films made of alternate polyelectrolyte multilayers of exponential and linear growth

The layer by layer deposition process of polyelectrolytes is used to construct films equipped with several compartments containing "free polyelectrolytes". Each compartment corresponds to a stratum of an exponentially growing polyelectrolyte multilayer film, and two consecutive compartments are separated by a stratum composed of a linearly growing multilayer that acts as a barrier preventing polyelectrolyte diffusion from one compartment to another. We use hyaluronic acid/poly(L-lysine) as the system to build the compartments and the poly(styrene sulfonate)/poly(allylamine) system for the barrier. Using confocal microscopy, it is shown that poly(L-lysine) diffuses only within the compartment in which it was initially introduced during the film construction and is thus unable to cross the barriers. Using fluorescein isothiocyanate as a pH indicator, it is also shown that although poly(styrene sulfonate)/poly(allylamine) multilayers act as a barrier for polyelectrolytes, they do not prevent proton diffusion through the film. Such films open the route for multiple functionalization of biomaterial coatings.     

Straightforward synthesis of conductive graphene/polymer nanocomposites from graphite oxide

The reduction of graphite oxide (GO) in the presence of reactive poly(methyl methacrylate) (PMMA), under mild biphasic conditions, directly affords graphene grafted with PMMA. The resulting nanocomposite shows excellent electrical conductivities resulting from the optimal dispersion and exfoliation of graphene in the polymer matrix.     

Layer-by-layer engineered Co-Al hydroxide nanosheets/graphene multilayer films as flexible electrode for supercapacitor

Multilayer films of Co-Al layered double hydroxide nanosheets (Co-Al LDH-NS) and graphene oxide (GO) were fabricated through layer-by-layer (LBL) assembly. By using a three-electrode system, the electrochemical performances of the films were investigated to evaluate their potential as electrode materials to be used in flexible supercapacitor devices. The Co-Al LDH-NS/GO multilayer films exhibited a high specific capacitance of 880 F/g and area capacitance of 70 F/m(2) under the scan rate of 5 mV/s. And the film exhibited good cycle stability over 2000 cycles. After treating the films at 200 °C in H(2) atmosphere, the specific capacitance and area capacitance were largely increased up to 1204 F/g and 90 F/m(2) due to partial reduction of GO. A flexible electrode by depositing Co-Al LDH-NS/GO multilayer film onto PET substrate was prepared to show the potential of Co-Al LDH-NS/GO films for flexible energy storage.     

Two step hydrothermal synthesis of flowerbud-like magnetite/graphene oxide hybrid with high-performance microwave absorption

A novel flowerbud-like magnetite/graphene oxide (GO) hybrid was synthesized from facile two-step hydrothermal process by using FeCl₃ as iron source, ethylene glycol as the reducing agent, and graphene oxide as template. The magnetite nanoparticles with the diameters of 70–80 nm were attached onto the surface of graphene oxide through the two-step self-assembly process which enhanced the magnetic properties of the hybrids. The final flowerbud-like magnetite/graphene oxide hybrid emerged with the saturated magnetization of ~84.5 emu g^–1. More importantly, owing to the combined contribution of enhanced dielectric and magnetic properties, the maximum microwave absorption of as-prepared magnetite/GO hybrid reached 30 dB with a thickness of 4 mm. Besides, the absorption bandwidth with a reflection loss above 23 dB ranged from 6.0 to 11.5 GHz.