Numerical study of large amplitude,nonsinusoidal motion and camber effects on pitching airfoil propulsion

The effects of large amplitude and nonsinusoidal motion on pitching airfoil aerodynamics for thrust generation were numerically studied with a 2-D NACA0012 airfoil used, and various 2-D NACA asymmetric airfoils were applied for camber effect study. The large amplitude effect study has been undertaken over a wide range of reduced frequency k (from 6 to 18) and pitching amplitude θ (from 5° to 30°) at Re=1.35×10⁴ with sinusoidal pitching profile used. It is shown that the large pitching amplitude results in much more thrust generated than that at low pitching amplitude and the increase of thrust with amplitude becomes slow when the amplitude reaches some degree. However, the propulsive efficiency noticeably decreases with the increase of θ at a fixed k.An adjustable parameter K was employed to realize various nonsinusoidal motions and the effect of nonsinusoidal motion was investigated with various unsteady parameters (θ, k) applied. The results reveal that nonsinusoidal motion has a noticeable effect on the aerodynamic performance, as it affects the instantaneous force coefficients, maximum thrust coefficients and flow structures. An increase in K results in a better thrust generation performance at fixed θ and k, especially for K>0. It is also shown that the larger K noticeably influences the wake pattern and induces a stronger reverse von Karman vortex street in the wake, which in turn leads to the increased thrust. The camber study was performed on various 2-D NACA airfoils with different cambers and camber locations undergoing sinusoidal pitching motion at θ=5° and Re=1.35×10⁴. It is found that varying camber offers little improvement in thrust generation performance.     

High fidelity numerical simulation of airfoil thickness and kinematics effects on flapping airfoil propulsion

High-fidelity numerical simulations with the spectral difference (SD) method are carried out to investigate the unsteady flow over a series of oscillating NACA 4-digit airfoils. Airfoil thickness and kinematics effects on the flapping airfoil propulsion are highlighted. It is confirmed that the aerodynamic performance of airfoils with different thickness can be very different under the same kinematics. Distinct evolutionary patterns of vortical structures are analyzed to unveil the underlying flow physics behind the diverse flow phenomena associated with different airfoil thickness and kinematics and reveal the synthetic effects of airfoil thickness and kinematics on the propulsive performance. Thickness effects at various reduced frequencies and Strouhal numbers for the same chord length based Reynolds number (=1200) are then discussed in detail. It is found that at relatively small Strouhal number (=0.3), for all types of airfoils with the combined pitching and plunging motion (pitch angle 20°, the pitch axis located at one third of chord length from the leading edge, pitch leading plunge by 75°), low reduced frequency (=1) is conducive for both the thrust production and propulsive efficiency. Moreover, relatively thin airfoils (e.g. NACA0006) can generate larger thrust and maintain higher propulsive efficiency than thick airfoils (e.g. NACA0030). However, with the same kinematics but at relatively large Strouhal number (=0.45), it is found that airfoils with different thickness exhibit diverse trend on thrust production and propulsive efficiency, especially at large reduced frequency (=3.5). Results on effects of airfoil thickness based Reynolds numbers indicate that relative thin airfoils show superior propulsion performance in the tested Reynolds number range. The evolution of leading edge vortices and the interaction between the leading and trailing edge vortices play key roles in flapping airfoil propulsive performance.     

Effect of flexure on aerodynamic propulsive efficiency of flapping flexible airfoil

The aim of present study is to investigate the effect of chord-wise flexure amplitude on unsteady aerodynamic characteristics for a flapping airfoil with various combinations of Reynolds number and reduced frequency. Unsteady, viscous flows over a single flexible airfoil in plunge motion are computed using conformal hybrid meshes. The dynamic mesh technique is applied to illustrate the deformation modes of the flexible flapping airfoil. In order to investigate the influence of the flexure amplitude on the aerodynamic performance of the flapping airfoil, the present study considers eight different flexure amplitudes (a₀) ranging from 0 to 0.7 in intervals of 0.1 under conditions of Re=10⁴, reduced frequency k=2, and dimensionless plunge amplitude h₀=0.4. The computed unsteady flow fields clearly reveal the formation and evolution of a pair of leading edge vortices along the body of the flexible airfoil as it undergoes plunge motion. Thrust-indicative wake structures are generated when the flexure amplitude of the airfoil is less than 0.5 of the chord length. An enhancement in the propulsive efficiency is observed for a flapping airfoil with flexure amplitude of 0.3 of the chord length. This study also calculates the propulsive efficiency and thrust under various Reynolds numbers and reduced frequency conditions. The results indicate that the propulsive efficiency has a strong correlation with the reduced frequency. It is found that the flow conditions which yield the highest propulsive efficiency correspond to Strouhal number St of 0.255.     

An experimental study of the effects of pitch-pivot-point location on the propulsion performance of a pitching airfoil

An experimental investigation was conducted to characterize the evolution of the unsteady vortex structures in the wake of a pitching airfoil with the pitch-pivot-point moving from 0.16C to 0.52C (C is the chord length of the airfoil). The experimental study was conducted in a low-speed wind tunnel with a symmetric NACA0012 airfoil model in pitching motion under different pitching kinematics (i.e., reduced frequency k=3.8–13.2). A high-resolution particle image velocimetry (PIV) system was used to conduct detailed flow field measurements to quantify the characteristics of the wake flow and the resultant propulsion performance of the pitching airfoil. Besides conducting “free-run” PIV measurements to determine the ensemble-averaged velocity distributions in the wake flow, “phase-locked” PIV measurements were also performed to elucidate further details about the behavior of the unsteady vortex structures. Both the vorticity–moment theorem and the integral momentum theorem were used to evaluate the effects of the pitch-pivot-point location on the propulsion performance of the pitching airfoil. It was found that the pitch-pivot-point would affect the evolution of the unsteady wake vortices and resultant propulsion performance of the pitching airfoil greatly. Moving the pitch-pivot-point of the pitching airfoil can be considered as adding a plunging motion to the original pitching motion. With the pitch-pivot-point moving forward (or backward), the added plunging motion would make the airfoil trailing edge moving in the same (or opposite) direction as of the original pitching motion, which resulted in the generated wake vortices and resultant thrust enhanced (or weakened) by the added plunging motion.     

An investigation into the effects of unsteady parameters on the aerodynamics of a low Reynolds number pitching airfoil

The growing applications of low Reynolds number (LRN) operating vehicles impose the need for accurate LRN flow solutions. These applications usually involve complex unsteady phenomena, which depend on the kinematics of the vehicle such as pitching, plunging, and flapping of a wing. The objective of the present study is to address the issues related to LRN aerodynamics of a harmonically pitching NACA0012 airfoil. To this end, the influence of unsteady parameters, namely, amplitude of oscillation, d, reduced frequency, k, and Reynolds number, Re, on the aerodynamic performance of the model is investigated. Computational fluid dynamics (CFD) is utilized to solve Navier–Stokes (N–S) equations discretized based on the Finite Volume Method (FVM). The resulting instantaneous lift coefficients are compared with analytical data from Theodorsen’s method. The simulation results reveal that d, k, and Re are of great importance in the aerodynamic performance of the system, as they affect the maximum lift coefficients, hysteresis loops, strength, and number of the generated vortices within the harmonic motion, and the extent of the so-called figure-of-eight phenomenon region. Thus, achieving the optimum lift coefficients demands a careful selection of these parameters.     

Schooling behavior of rigid and flexible heaving airfoils

The schooling behavior of rigid and flexible NACA0017 airfoils undergoing a heaving motion was experimentally explored using a merry-go-round configuration. Each airfoil was attached to the end of a horizontal support bar whose other end was connected to a freely rotating vertical axis. The axis was forced to undergo a sinusoidal motion in the vertical direction to generate a pure heaving motion of the airfoil in the frequency range of 0.4 to 4.8 Hz. The propulsion due to the heaving airfoil was expressed as the horizontal rotational speed of the support bar. This experimental setup simulates an infinite schooling of airfoils separated by a streamwise distance d undergoing in-phase heaving motions. The ratio of the distance to the chord length, d/c, was determined by the number of airfoils (2 ≤ n ≤ 8). The variation in rotational frequency F as a function of heaving frequency f was determined using different experimental parameters. The schooling number S = f /(nF), which represents the number of heaving oscillations between each pair of successive airfoils, was introduced to explain the schooling behavior of the airfoils. The effects of airfoil flexibility, d/c and f on the propulsive performance were examined in the context of the schooling behavior of the airfoils.     

Numerical investigations into the asymmetric effects on the aerodynamic response of a pitching airfoil

The effects of asymmetric sinusoidal motion on pitching airfoil aerodynamics were studied by numerical simulations for 2-D flow around a NACA0012 airfoil at Re=1.35×10⁵. Various unsteady parameters (amplitude of oscillation, d; reduced frequency, k) were applied to investigate the effect of asymmetry parameter S on the instantaneous force coefficients and flow patterns. The results reveal that S has a noticeable effect on the aerodynamic performance, as it affects the instantaneous force coefficient, maximum lift and drag coefficient, hysteresis loops and the flow structures.     

Experimental study of pitching and plunging airfoils at low Reynolds numbers

Measurements of the unsteady flow structure and force time history of pitching and plunging SD7003 and flat plate airfoils at low Reynolds numbers are presented. The airfoils were pitched and plunged in the effective angle of attack range of 2.4°–13.6° (shallow-stall kinematics) and ?6° to 22° (deep-stall kinematics). The shallow-stall kinematics results for the SD7003 airfoil show attached flow and laminar-to-turbulent transition at low effective angle of attack during the down stroke motion, while the flat plate model exhibits leading edge separation. Strong Re-number effects were found for the SD7003 airfoil which produced approximately 25 % increase in the peak lift coefficient at Re = 10,000 compared to higher Re flows. The flat plate airfoil showed reduced Re effects due to leading edge separation at the sharper leading edge, and the measured peak lift coefficient was higher than that predicted by unsteady potential flow theory. The deep-stall kinematics resulted in leading edge separation that led to formation of a large leading edge vortex (LEV) and a small trailing edge vortex (TEV) for both airfoils. The measured peak lift coefficient was significantly higher (~50 %) than that for the shallow-stall kinematics. The effect of airfoil shape on lift force was greater than the Re effect. Turbulence statistics were measured as a function of phase using ensemble averages. The results show anisotropic turbulence for the LEV and isotropic turbulence for the TEV. Comparison of unsteady potential flow theory with the experimental data showed better agreement by using the quasi-steady approximation, or setting C(k) = 1 in Theodorsen theory, for leading edge–separated flows.     

Aerodynamics of laminar separation flutter at a transitional Reynolds number

Experimental observations of self-sustained pitch oscillations of a NACA 0012 airfoil at transitional Reynolds numbers were recently reported. The aeroelastic limit cycle oscillations, herein labelled as laminar separation flutter, occur in the range 5.0×10⁴≤Re_c≤1.3×10⁵. They are well behaved, have a small amplitude and oscillate about θ=0°. It has been speculated that laminar separation leading to the formation of a laminar separation bubble, occurring at these Reynolds numbers, plays an essential role in these oscillations. This paper focuses on the Re_c=7.7×10⁴ case, with the elastic axis located at 18.6% chord. Considering that the experimental rig acts as a dynamic balance, the aerodynamic moment is derived and is empirically modelled as a generalized Duffing–van-der-Pol nonlinearity. As expected, it behaves nonlinearly with pitch displacement and rate. It also indicates a dynamically unstable equilibrium point, i.e. negative aerodynamic damping. In addition, large eddy simulations of the flow around the airfoil undergoing prescribed simple harmonic motion, using the same amplitude and frequency as the aeroelastic oscillations, are performed. The comparison between the experiment and simulations is conclusive. Both approaches show that the work done by the airflow on the airfoil is positive and both have the same magnitude. The large eddy simulation (LES) computations indicate that at θ=0°, the pitching motion induces a lag in the separation point on both surfaces of the airfoil resulting in negative pitching moment when pitching down, and positive moment when pitching up, thus feeding the LCO.     

Thrust augmentation of flapping airfoils in low Reynolds number flow using a flexible membrane

The unsteady aerodynamic thrust and aeroelastic response of a two-dimensional membrane airfoil under prescribed harmonic motion are investigated computationally with a high-order Navier–Stokes solver coupled to a nonlinear membrane structural model. The effects of membrane prestress and elasticity are examined parametrically for selected plunge and pitch–plunge motions at a chord-based Reynolds number of 2500. The importance of inertial membrane loads resulting from the prescribed flapping is also assessed for pure plunging motions. This study compares the period-averaged aerodynamic loads of flexible versus rigid membrane airfoils and highlights the vortex structures and salient fluid–membrane interactions that enable more efficient flapping thrust production in low Reynolds number flows.     

Influence of heat transfer on the aerodynamic performance of a plunging and pitching NACA0012 airfoil at low Reynolds numbers

The unsteady low Reynolds number aerodynamics phenomena around flapping wings are addressed in several investigations. Elsewhere, airfoils at higher Mach numbers and Reynolds numbers have been treated quite comprehensively in the literature. It is duly noted that the influence of heat transfer phenomena on the aerodynamic performance of flapping wings configurations is not well studied. The objective of the present study is to investigate the effect of heat transfer upon the aerodynamic performance of a pitching and plunging NACA0012 airfoil in the low Reynolds number flow regime with particular emphasis upon the airfoil's lift and drag coefficients. The compressible Navier–Stokes equations are solved using a finite volume method. To consider the variation of fluid properties with temperature, the values of dynamic viscosity and thermal diffusivity are evaluated with Sutherland's formula and the Eucken model, respectively. Instantaneous and mean lift and drag coefficients are calculated for several temperature differences between the airfoil surface and freestream within the range 0–100 K. Simulations are performed for a prescribed airfoil motion schedule and flow parameters. It is learnt that the aerodynamic performance in terms of the lift C_L and drag C_D behavior is strongly dependent upon the heat transfer rate from the airfoil to the flow field. In the plunging case, the mean value of C_D tends to increase, whereas the amplitude of C_L tends to decrease with increasing temperature difference. In the pitching case, on the other hand, the mean value and the amplitude of both C_D and C_L decrease. A spectral analysis of C_D and C_L in the pitching case shows that the amplitudes of both C_D and C_L decrease with increasing surface temperature, whereas the harmonic frequencies are not affected.     

Dynamic stall behavior from unsteady force measurements

A direct force measurement technique employing piezoelectric load cells is used to experimentally investigate a two-dimensional airfoil (NACA 0012) undergoing dynamic stall. The load cells are installed at each end of the airfoil and give the force response in two directions in the plane normal to the airfoil axis during oscillations. Experiments are carried out at a Reynolds number based on the airfoil chord equal to 7.7×10⁴, and at four reduced frequencies, k=0.005, 0.01, 0.02, and 0.04. Phase-averaged lift of the airfoil undergoing dynamic stall is presented. It is observed that hysteresis loops of the lift occur both when the airfoil is pitched to exceed its static stall limit and when it is still within its static stall limit, and they grow in size with increasing k at the same pitching mean angle of attack and pitching amplitude. Both the lift and the drag induced by the pitching motion are further analyzed using the methods of higher order correlation analysis and continuous wavelet transforms to undercover their nonlinear and nonstationary features, in addition to classical FFT-based spectral analysis. The results are quantitatively illustrated by an energy partition analysis. It is found that the unsteady lift and drag show opposite trends when the airfoil undergoes transition from the pre-stall regime to the full-stall regime. The degree of nonlinearity of the lift increases, and the lift show a nonstationary feature in the light-stall regime, while the nonlinearity of the drag decreases, and the drag shows nonstationary feature in both the light-stall and the full-stall regimes. Furthermore, the lift and the drag have significant nonlinear interactions as shown by the correlation analysis in the light-stall regime.     

A study of long separation bubble on thick airfoils and its consequent effects

A parametric study has been performed to analyse the flow around the thick-symmetric NACA 0021 airfoil in order to better understand the characteristics and effects of long separation bubbles (LoSBs) that exist on such airfoils at low Reynolds numbers and turbulence intensities. In the article, the prediction capabilities of two recently-developed transition models, the correlation-based γ–Re_θ model and the laminar-kinetic-energy-based κ–κ_L–ω model are assessed. Two-dimensional steady-state simulations indicated that the κ–κ_L–ω model predicted the separation and reattachment process accurately when compared with published experimental work. The model was then used to study the attributes and the effects of LoSBs as a function of the angle of attack, freestream turbulence intensity and Reynolds number. It was observed that LoSBs considerably degrade the aerodynamic performance of airfoils and lead to abrupt stall behaviour. It is, furthermore, illustrated that the presence of the LoSB leads to an induced camber effect on the airfoil that increases as the airfoil angle of attack increases due to the upstream migration of the bubble. An increase in the Reynolds number or turbulence levels leads to a reduction in the bubble extent, considerably improving the airfoil performance and leading to a progressive trailing-edge stall.     

Flow field characteristics study of a flapping airfoil using computational fluid dynamics

The flow field of a flapping airfoil in Low Reynolds Number (LRN) flow regime is associated with complex nonlinear vortex shedding and viscous phenomena. The respective fluid dynamics of such a flow is investigated here through Computational Fluid Dynamics (CFD) based on the Finite Volume Method (FVM). The governing equations are the unsteady, incompressible two-dimensional Navier-Stokes (N-S) equations. The airfoil is a thin ellipsoidal geometry performing a modified figure-of-eight-like flapping pattern. The flow field and vortical patterns around the airfoil are examined in detail, and the effects of several unsteady flow and system parameters on the flow characteristics are explored. The investigated parameters are the amplitude of pitching oscillations, phase angle between pitching and plunging motions, mean angle of attack, Reynolds number (Re), Strouhal number (St) based on the translational amplitudes of oscillations, and the pitching axis location (x/c). It is shown that these parameters change the instantaneous force coefficients quantitatively and qualitatively. It is also observed that the strength, interaction, and convection of the vortical structures surrounding the airfoil are significantly affected by the variations of these parameters.     

Effect of flow regime change from subsonic to transonic on the air loads of an oscillating airfoil

In this research, the effect of flow regime change from subsonic to transonic on the air loads of a pitching NACA0012 airfoil is investigated. To do this, the effect of change in flow regime on the lift and pitching moment coefficients hysteresis cycles is studied. The harmonic balance approach is utilized for numerical calculation due to its low computational time. Verifications are also made with previous works and good agreements are observed. The assessment of flow regime change on the aforementioned hysteresis cycles is accomplished in the Mach number range of M=0.65–0.755. The reduced frequency and pitch amplitude also vary from k=0.03 to 0.1 and α₀=1–2.51°, respectively. Results show that the effect of increase in Mach number is to increase and decrease the lift coefficient during downstroke and upstroke, respectively, whereas at low reduced frequencies, the effect of increase in Mach number may lead to a reverse manner when airfoil moves toward its extremum angle of attack. Results also reveal that as the pitch amplitude varies, the shape of lift coefficient hysteresis cycle depends more on the pitch amplitude than on the appearance of shock. It is shown that as the Mach number increases, the incidence angles correspond to the extremum pitching moment, and depending on the reduced frequency, lie between zero and extremum angle of attack. These incidence angles shift toward the extremum angle of attack as the reduced frequency decreases. Results also show that the increase in pitch amplitude at low Mach number, in such a way that leads to the formation of shock around the extremum angle of attack, causes the extremum pitching moment to appear around these angles and at high Mach number, depending on the reduced frequency, the extremum pitching moment incidence angles would be between zero and extremum incidence angle.     

Experimental study of wings undergoing active root flapping and pitching

This paper presents the results of experiments carried out on mechanical wings undergoing active root flapping and pitching in the wind tunnel. The objective of the work is to investigate the effect of the pitch angle oscillations and wing profile on the aerodynamic forces generated by the wings. The experiments were repeated for a different reduced frequency, airspeed, flapping and pitching kinematics, geometric angle of attack and wing sections (one symmetric and two cambered airfoils). A specially designed mechanical flapper was used, modelled on large migrating birds. It is shown that, under pitch leading conditions, good thrust generation can be obtained at a wide range of Strouhal numbers if the pitch angle oscillation is adjusted accordingly. Consequently, high thrust was measured at both the lowest and highest tested Strouhal numbers. Furthermore, the work demonstrates that the aerodynamic forces can be sensitive to the Reynolds number, depending on the camber of the wings. Under pitch lagging conditions, where the effective angle of attack amplitude is highest, the symmetric wing was affected by the Reynolds number, generating less thrust at the lowest tested Reynolds value. In contrast, under pure flapping conditions, where the effective angle of attack amplitude was lower but still significant, it was the cambered wings that demonstrated Reynolds sensitivity.     

Camber effects in the dynamic aeroelasticity of compliant airfoils

This paper numerically investigates the effect of chordwise flexibility on the dynamic stability of compliant airfoils. A classical two-dimensional aeroelastic model is expanded with an additional degree of freedom to capture time-varying camber deformations, defined by a parabolic bending profile of the mean aerodynamic chord. Aerodynamic forces are obtained from unsteady thin airfoil theory and the corresponding compliant-airfoil inertia and stiffness from finite-element analysis. V–g and state-space stability methods have been implemented in order to compute flutter speeds. The study looks at physical realizations with an increasing number of degrees of freedom, starting with a camber-alone system. It is shown that single camber leads to flutter, which occurs at a constant reduced frequency and is due to the lock in between the shed wake and the camber motion. The different combinations of camber deformations with pitch and plunge motions are also studied, including parametric analyses of their aeroelastic stability characteristics. A number of situations are identified in which the flutter boundary of the compliant airfoil exhibits a significant dip with respect to the rigid airfoil models. These results can be used as a first estimation of the aeroelastic stability boundaries of membrane-wing micro air vehicles.     

弯度翼型大迎角时分离涡流场的多平衡态现象

基于kω的SST两方程湍流模型,在时间域求解雷诺平均Navier-Stokes方程,模拟弯度翼型大迎角时的分离流动。通过给翼型施加一定形式的扰动,重点关注了翼型弯度对大迎角分离涡流场平衡态转移的影响。研究结果表明:与相同厚度20%以上的对称翼型相比,2%弯度的翼型出现分离涡流场平衡态转移的起始迎角变小2°左右,迎角区间变宽约1°;在厚度相对较小的NACA2416翼型上也发现上述分离涡平衡态转移现象。由此说明翼型弯度在一定程度上促使了分离涡平衡态的转移。     

High-fidelity simulations of moving and flexible airfoils at low Reynolds numbers

The present paper highlights results derived from the application of a high-fidelity simulation technique to the analysis of low-Reynolds-number transitional flows over moving and flexible canonical configurations motivated by small natural and man-made flyers. This effort addresses three separate fluid dynamic phenomena relevant to small fliers, including: laminar separation and transition over a stationary airfoil, transition effects on the dynamic stall vortex generated by a plunging airfoil, and the effect of flexibility on the flow structure above a membrane airfoil. The specific cases were also selected to permit comparison with available experimental measurements. First, the process of transition on a stationary SD7003 airfoil section over a range of Reynolds numbers and angles of attack is considered. Prior to stall, the flow exhibits a separated shear layer which rolls up into spanwise vortices. These vortices subsequently undergo spanwise instabilities, and ultimately breakdown into fine-scale turbulent structures as the boundary layer reattaches to the airfoil surface. In a time-averaged sense, the flow displays a closed laminar separation bubble which moves upstream and contracts in size with increasing angle of attack for a fixed Reynolds number. For a fixed angle of attack, as the Reynolds number decreases, the laminar separation bubble grows in vertical extent producing a significant increase in drag. For the lowest Reynolds number considered (Re _c  = 10⁴), transition does not occur over the airfoil at moderate angles of attack prior to stall. Next, the impact of a prescribed high-frequency small-amplitude plunging motion on the transitional flow over the SD7003 airfoil is investigated. The motion-induced high angle of attack results in unsteady separation in the leading edge and in the formation of dynamic-stall-like vortices which convect downstream close to the airfoil. At the lowest value of Reynolds number (Re _c  = 10⁴), transition effects are observed to be minor and the dynamic stall vortex system remains fairly coherent. For Re _c  = 4 × 10⁴, the dynamic-stall vortex system is laminar at is inception, however shortly afterwards, it experiences an abrupt breakdown associated with the onset of spanwise instability effects. The computed phased-averaged structures for both values of Reynolds number are found to be in good agreement with the experimental data. Finally, the effect of structural compliance on the unsteady flow past a membrane airfoil is investigated. The membrane deformation results in mean camber and large fluctuations which improve aerodynamic performance. Larger values of lift and a delay in stall are achieved relative to a rigid airfoil configuration. For Re _c = 4.85 × 10⁴, it is shown that correct prediction of the transitional process is critical to capturing the proper membrane structural response.     

Direct numerical simulation of a NACA0012 in full stall

This work aims at investigating the mechanisms of separation and the transition to turbulence in the separated shear-layer of aerodynamic profiles, while at the same time to gain insight into coherent structures formed in the separated zone at low-to-moderate Reynolds numbers. To do this, direct numerical simulations of the flow past a NACA0012 airfoil at Reynolds numbers Re = 50,000 (based on the free-stream velocity and the airfoil chord) and angles of attack AOA = 9.25° and AOA = 12° have been carried out. At low-to-moderate Reynolds numbers, NACA0012 exhibits a combination of leading-edge/trailing-edge stall which causes the massive separation of the flow on the suction side of the airfoil. The initially laminar shear layer undergoes transition to turbulence and vortices formed are shed forming a von Kármán like vortex street in the airfoil wake. The main characteristics of this flow together with its main features, including power spectra of a set of selected monitoring probes at different positions on the suction side and in the wake of the airfoil are provided and discussed in detail.