交联助剂对PPC／NBR弹性体结构和性能的影响

研究了马来酸酐（ＭＡ）及异氰脲酸三烯丙酯（ＴＡＩＣ）对聚丙撑碳酸酯／丁腈橡胶共混弹性体结构和性能的影响，发出加入ＭＡ或ＴＡＩＣ能有效地改善交联网络；加入适量ＭＡ能显著改善共混弹性体热氧老化稳定性；加入ＴＡＩＣ使共混弹性体具有优良的高弹特性和力学性能。     

Polyamide 66/EPR‐g‐MA blends: mechanical modeling and kinetic analysis of thermal degradation

The present investigation deals with the mechanical, thermal, and morphological properties of binary nylon 66/maleic anhydride grafted ethylene propylene rubber (EPR‐g‐MA) blends at different dispersed phase (EPR‐g‐MA) concentrations. The effects of EPR‐g‐MA concentration and dispersed particle size on the mechanical properties of the blends were studied. Analysis of the tensile data in terms of various theoretical models revealed the variation of stress concentration effect with blend composition and the improvement of interfacial adhesion between dispersed rubber phase and nylon 66 matrix. The thermal degradation of the blends was analyzed by nonisothermal thermogravimetric analysis (TGA). It was found that the activation energy (E_a) and overall reaction order of thermal degradation decreased with increasing EPR‐g‐MA content. The scanning electron microscopic (SEM) analysis showed a significant decrease in dispersed particle size with increasing EPR‐g‐MA content, which was explained on the basis of the level of chemical interaction (in situ compatibilization) between nylon 66 and EPR‐g‐MA. The surface morphology of the nylon 66/EPR‐g‐MA blends was illustrated by the roughness of atomic force microscopy (AFM) images. Copyright © 2008 John Wiley & Sons, Ltd.     

Ultra‐high molecular weight styrenic block copolymer/TPU blends for automotive applications: Influence of various compatibilizers

Thermoplastic elastomers (TPEs) based on new generation ultrahigh molecular weight styrene‐ethylene‐butylene‐styrene (SEBS) and thermoplastic polyurethane (TPU) are developed and characterized especially for automotive applications. Influence of maleic anhydride grafted styrene‐ethylene‐butylene‐styrene (SEBS‐g‐MA) and maleic anhydride grafted ethylene propylene rubber (EPM‐g‐MA) as compatibilizers has been explored and compared on the blends of SEBS/TPU (60:40). The amount of compatibilizers was varied from 0 to 10 phr. Scanning electron microscopy (SEM) and atomic force microscopy (AFM) studies revealed the dramatic changes from a nonuniform to finer and uniform dispersed phase morphology. This was reflected in various mechanical properties. SEBS‐g‐MA modified blends showed higher tensile strength. EPM‐g‐MA modified blends also displayed considerable improvement. Elongation at break (EB) was doubled for the entire compatibilized blends. Fourier‐transform infrared spectrometry (FTIR) confirmed the chemical changes in the blends brought about by the interactions between blend components and compatibilizers. Both SEBS‐g‐MA and EPM‐g‐MA had more or less similar effects in dynamic mechanical properties of the blends. Additionally, melt rheological studies have also been pursued through a rubber process analyzer (RPA) to get a better insight.     

Completely biodegradable composites of poly(propylene carbonate) and short,lignocellulose fiber Hildegardia populifolia

The composites of biodegradable poly(propylene carbonate) (PPC) reinforced with short Hildegardia populifolia natural fiber were prepared by melt mixing followed by compression molding. The mechanical properties, thermal properties, and morphologies of the composites were studied via static and dynamic mechanical measurements, thermogravimetric analysis, and scanning electron microscopy (SEM) techniques, respectively. Static tensile tests showed that the stiffness and tensile strength of the composites increased with an increasing fiber content. However, the elongation at break and the energy to break decreased dramatically with the addition of short fiber. The relationship between the experimental results and the compatibility or interaction between the PPC matrix and fiber was correlated. SEM observations indicated good interfacial contact between the short fiber and PPC matrix. Thermogravimetric analysis revealed that the introduction of short Hildegardia populifolia fiber led to a slightly improved thermooxidative stability of PPC. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 666–675, 2004     

CHARACTERIZATION AND THERMAL STABILITY OF PMR POLYIMIDES USING 7-OXA-BICYCLO[2,2,l]HEPT-5-ENE-2,3-DICARBOXYLIC ANHYDRIDE AS END CAPS

An anhydride monomer containing ether oxide bridge,7-oxa-bicyclo[2,2,1]hept-5-ene-2,3-dicarboxylic anhydride (ONA),was successfully synthesized by Diels-Alder reaction of furan and maleic anhydride.The ONA was also studied as an end-cap for the polymerization of monomer reactant(PMR) type polyimides.Three molecular weight levels of the ONA end-capped PMR resins were evaluated.The effects of process conditions of these novel PMR resins on thermal and mechanical properties were investigated.It was demonstr...     

Effects of functionalized multiwalled carbon nanotubes on the morphologies and mechanical properties of PP/EVA blend

The maleic anhydride‐grafted multiwalled carbon nanotubes (MWCNTs‐g‐MA) have been introduced into polypropylene/ethylene‐co‐vinyl acetate (PP/EVA) blend. To clearly describe the effects of MWCNTs‐g‐MA on the morphology and mechanical properties of PP/EVA blends, the selective distribution of MWCNTs‐g‐MA in the blends is realized through different sample preparation methods, namely, MWCNTs‐g‐MA disperse in EVA phase and MWCNTs‐g‐MA disperse in PP matrix. The results show that the distribution of MWCNTs‐g‐MA has an important effect on the final morphology of EVA and the crystallization structure of PP matrix. Compared with PP/EVA binary blend, distribution of MWCNTs‐g‐MA in PP matrix induces the aggregation of EVA phase at high EVA content and the decrease of spherulite diameters of PP matrix simultaneously. However, when MWCNTs‐g‐MA are dispersed in the EVA phase, they induce more homogeneous distribution of EVA, and the crystallization behavior of PP is slightly affected by MWCNTs‐g‐MA. The corresponding mechanical properties including impact strength and tensile strength are tested and analyzed in the work. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 1481–1491, 2009     

Preparation and characterization of poly(propylene carbonate)/montmorillonite nanocomposites by solution intercalation

Poly(propylene carbonate) (PPC) is a new biodegradable aliphatic polycarbonate. However, the poor thermal stability and low glass transition temperatures (T_g) have limited its applications. To improve the thermal properties of PPC, organophilic montmorillonite (OMMT) was mixed with PPC by a solution intercalation method to produce nanocomposites. An intercalated-and-flocculated structure of PPC/OMMT nanocomposites was confirmed by X-ray diffraction (XRD) and transmission electron microscopy (TEM). The thermal and mechanical properties of PPC/OMMT nanocomposites were investigated by thermal gravimetric analysis (TGA), differential scanning calorimetric (DSC), and electronic tensile tester. Due to the nanometer-sized dispersion of layered silicate in polymer matrix, PPC/OMMT nanocomposites exhibit improved thermal and mechanical properties than pure PPC. When the OMMT content is 4 wt%, the PPC/OMMT nanocomposite shows the best thermal and mechanical properties. These results indicate that nanocomposition is an efficient and convenient method to improve the properties of PPC.     

Morphological Stability of Poly(propylene) Nanocomposites

Poly(propylene) compounds containing organophilic layered nanosilicates were prepared by means of melt extrusion at 210°C in order to investigate the influence of maleic anhydride‐grafted poly(propylene) (PP‐g‐MA) as a compatibilizer on morphology development and rheological properties. It was found that the addition of PP‐g‐MA leads to the strong exfoliation of silicate layers within the matrix as investigated by WAXS. This process is associated with the build up of an unstable morphology as probed by dynamic rheology and with the violation of the time‐temperature superposition principle. Annealing of the samples at extrusion temperature level leads to a coarsening of the silicate superstructure and further improvement of the exfoliation at the same time. This process results in a stable morphology with unique rheological properties indicating network‐like superstructure of silicate layers.     

PHBV-GMA与PHBV-GMA/PPC共混物中接枝物的热性能与形态结构

以甲基丙烯酸缩水甘油酯(GMA)单体对聚(3-羟基丁酸酯-3-羟基戊酸酯)(PHBV)接枝改性,得到的产物PHBV-GMA与封端后的聚碳酸亚丙酯(PPC)反应性共混。索氏抽提器提取PHBV-GMA和PHBV-GMA/PPC共混物,分别得到两种接枝产物PHBV-g-GMA和PHBV-g-PPC,用差示扫描量热法(DSC)、偏光显微镜(POM)以及原子力显微镜(AFM)研究其热性能和形态结构。结果发现,GMA接枝后,对PHBV结晶有成核效应。PPC接枝PHBV后,接枝物PHBV-g-PPC结晶度降低,球晶尺寸减小,PHBV和PPC两种大分子间的相分离程度降低,相容性明显提高。     

Poly(lactic acid)/(styrene‐ethylene‐butylene‐styrene)‐g‐maleic anhydride copolymer/sepiolite nanocomposites: Investigation of thermo‐mechanical and morphological properties

In this study, sepiolite nanoclay is used as reinforcing agent for poly(lactic acid) (PLA)/(styrene‐ethylene‐butylene‐styrene)‐g‐maleic anhydride copolymer (SEBS‐g‐MA) 90/10 (w/w) blend. Effects of sepiolite on thermal behavior, morphology, and thermomechanical properties of PLA/SEBS‐g‐MA blend were investigated. Differential scanning calorimetry results showed 7% improvement in crystallinity at 0.5 wt% of sepiolite. The nanocomposite exhibited approximately 36% increase in the tensile modulus and 17% increase in toughness as compared with the blend matrix at 0.5 and 2.5 wt% of sepiolite respectively. Field emission scanning electron microscopy and transmission electron microscopy images exhibited sepiolite‐induced morphological changes and dispersion of sepiolite in both PLA and SEBS‐g‐MA phases. Dynamic mechanical analysis and wide angle X‐ray diffraction present evidences in support of the reinforcing nature of sepiolite and phase interaction between the filler and the matrix. This study confirms that sepiolite can improve tensile modulus and toughness of PLA/SEBS‐g‐MA blend.     

Correlation of morphological parameters and mechanical performance of polyamide‐612/poly (ethylene–octene) elastomer blends

Blends of polyamide‐612 (PA‐612) and maleic anhydride grafted poly (ethylene–octene) elastomer (POE‐g‐MA) as an impact modifier have been prepared in the composition range of 0–35 wt. % of POE‐g‐MA and subsequently investigated for their structural, thermal, mechanical, dynamic mechanical properties and morphological attributes. X‐ray diffraction studies revealed a decrease in crystallinity whereas the thermal properties such as onset to degradation temperature and crystallization temperature remained broadly unaffected. Nearly three‐fold increase in the impact strength is registered accompanied by substantial increase in tensile failure strain, though tensile modulus (E) and tensile yield strength (σ _y) decreased with increase in impact modifier content. Dynamic mechanical analysis exhibited a singularity response in the loss factor in the temperature range of ~10°C–50°C. Micromechanical aspects were analyzed using conventional theoretical models for low strain mechanical response (E) such as rule of mixtures and foam model and for high strain mechanical response (σ _y) such as Nikolais–Narkis model and porosity model. Impact toughness and strain‐at‐break of the investigated composition were successfully correlated to the domain size (D_n) of the dispersed phase and their inter‐particle distances (τ). Scanning electron microscopy showed the coalescence of domains of the dispersed phase at higher POE content and thus reiterates the crucial role of inter‐particle distance in controlling the toughening mechanism of POE blended PA‐612. Copyright © 2013 John Wiley & Sons, Ltd.     

聚碳酸1,2-丙二酯/蒙脱土复合材料的制备与性能

利用阳离子交换法,以十六烷基三甲基溴化铵(HTAB)改性钠基蒙脱土制备了有机改性蒙脱土(OMMT),OMMT的层间距达到了2nm,比普通的钠基蒙脱土增加了0.74nm.采用熔融插层法制备了插层-絮凝型PPC/OMMT复合材料,当复合材料中OMMT含量为5wt%时,复合材料的杨氏模量较纯PPC树脂大幅度提高了61.8%,同时玻璃化温度(Tg)提高了2.4℃,热分解温度提高了32.3℃.因此,OMMT对大幅度提高PPC的杨氏模量具有很大的潜力.     

氯化聚丙撑碳酸酯增容聚丙撑碳酸酯/秸秆粉复合材料的制备及性能

聚丙撑碳酸酯(PPC)是一种新型热塑性生物降解材料,但其热性能及力学性能较差,应用受到限制。以秸秆粉这种农作物副产品作为增强体改性PPC,既可以提高PPC的力学性能同时又可开发利用秸秆资源。氯化聚丙撑碳酸酯(CPPC)是聚丙撑碳酸酯(PPC)经过氯化得到的,对天然纤维表面具有良好的浸润性和粘结性。本文以CPPC为增容剂,通过熔融共混法制备了PPC/秸秆粉复合材料。采用扫描电子显微镜(SEM)、拉伸实验、动态力学性能测试(DMA)及转矩流变仪对复合材料的结构及性能进行了表征,重点考察了CPPC的添加量对复合材料力学和流变性能的影响。结果表明,当CPPC质量分数为1.8%时,可使添加质量分数为30%秸秆粉的PPC复合材料拉伸强度提高38%,模量提高30%。同时,CPPC的引入使复合材料的粘度下降,改善了PPC/秸秆粉复合材料的加工性能。因此,作为增容剂的CPPC为制备高性能PPC/天然纤维复合材料提供了新的解决办法。     

Effect of maleic anhydride‐grafted polytetrafluoroethylene on the tensile and tribological properties of blending polytetrafluoroethylene with polyamide‐6

Blending polytetrafluoroethylene (PTFE) to polyamide‐6 (PA6) with and without maleic anhydride‐grafted polytetrafluoroethylene (PTFE‐g‐MA) was produced in a corotating twin screw extruder, where PTFE acts as the polymer matrix and PA6 as the dispersed phase. The effect of PTFE‐g‐MA on the tensile properties and tribological propertiesof PTFE/PA6 polymer blends is studied. Results show that the structural stability and morphology of the blends were greatly improved by PTFE‐g‐PA6 grafted copolymers, which were formed by the in situ reaction of anhydride groups with the amino end groups of PA6 during reactive extrusion forming an imidic linkage. The presence of PTFE‐g‐PA6 in the PTFE continuous phase improves the interfacial adhesion, as a result of the creation of an interphase that was formed by the interaction between the formed PTFE‐g‐PA6 copolymer in situ and both phases. Compared with thePTFE/PA6 without PTFE‐g‐MA, the PTFE/PA6 with PTFE‐g‐MAhad the lowest friction coefficient and wear under given applied load and reciprocating sliding frequency. The interfacial compatibility of the composite prevented the rubbing‐off of PA6, accordingly improved the friction and wear properties of the composite. Copyright © 2009 John Wiley & Sons, Ltd.     

Water-Containing Cured Resin from Inverted Emulsion of Unsaturated Polyester Based on Divalent Metal Salt of Mono(hydroxyethyl)phthalate

Inverted emulsion, i.e., water-in-oil (W/O) type emulsion, was prepared from styrene solution of unsaturated polyester obtained from Mg salt of mono(hydroxyethyl)phthalate, ethylene glycol (EG), maleic anhydride (MA), phthalic anhydride (PA), and propylene oxide (PO). The inverted emulsion was much more stable than that of blank polyester obtained from EG, MA, PA, and PO, and further than the usual inverted emulsion prepared by treating styrene solution of commercial unsaturated polyester with triethanolamine. By polymerization, the inverted emulsion was transformed to a white solid which was dry to the touch. The water-containing cured resin obtained showed considerably higher physical and other properties than those of commercial unsaturated polyester.     

Syndiotactic poly(propylene)/organoclay nanocomposite fibers: influence of the nano‐filler and the compatibilizer on the fiber properties

Melt spinning of nanocomposites prepared from syndiotactic poly(propylene) (sPP) and organolayered silicate (M‐ODA), containing bound octadecyl ammonium chains, was investigated. The influence of the nano‐filler reinforcement and the role of the addition of maleic anhydride grafted isotactic poly(propylene) (iPP‐g‐MA) as compatibilizer with respect to the fiber proportion was examined. The presence of nano‐filler, the drawing ratio, and the compatibilizer addition afforded increased tenacity of the fibers. Only in the presence of the compatibilizer high drawing ratio of the sPP nanocomposite fibers was achieved. Transmission electron microscopy (TEM) was applied to monitor morphology development during nanocomposite fiber spinning in the presence and the absence of the compatibilizer. Copyright © 2005 John Wiley & Sons, Ltd.     

Interplay between bulk viscoelasticity and surface energy in autohesive tack of rubber‐tackifier blends

The effects of change in surface energy and bulk viscoelastic properties on the autohesive tack strength of brominated isobutylene‐co‐p‐methylstyrene (BIMS) rubber have been investigated by the addition of hydrocarbon resin (HCR) tackifier and maleated hydrocarbon resin (MA‐g‐HCR) tackifier. The addition of compatible HCR tackifier results in a reasonable increment in the tack strength of BIMS rubber by modifying only the bulk viscoelastic properties (compliance, entanglement molecular weight, relaxation time, self‐diffusion, and monomer friction coefficient values) of BIMS rubber to perform better during the course of bonding and debonding steps of the peel test. Incorporation of MA‐g‐HCR tackifier (containing 5–20 wt % of grafted maleic anhydride) steadily increases the tack strength of BIMS rubber further by precisely modifying both the surface energy and bulk viscoelastic properties to perform much better in the bonding and debonding steps. However, beyond 20 wt % of grafted maleic anhydride in the HCR tackifier, the tack strength starts decreasing due to the incompatibility between the blend components, and hence, the bulk viscoelastic properties required for bond formation are severely retarded by the interrelated reinforcing effect and the phase separation effect of the brittle MA‐g‐HCR tackifier in the BIMS rubber. Hence, the polar groups in a tackifier will contribute to significant enhancement of autohesive tack strength only if the bulk viscoelastic property of the rubber‐tackifier blend is favorable for bond formation and bond separation. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 972–982, 2010     

Preparation and Characterization of Poly(Lactic Acid)-g-Maleic Anhydride + Starch Blends

Poly(lactic acid) (PLA) and starch copolymers are obtained by reactive blending - varying the starch compositions from 0 to 60%. PLA is functionalized with maleic anhydride (MA), obtaining PLA-g-MA copolymers using dicumyl peroxide as an initiator of grafting in order to improve the compatibility and interfacial adhesion between the constituents. PLA + starch blends without a compatibilizer do not have sufficient interfacial adhesion. Decomposition temperature of PLA is not affected by grafting. Glass transition temperatures and dynamic mechanical properties are affected since MA has a plasticizing effect. Along with an increasing starch content friction decreases while wear loss volume in pin-on-disk tribometry has a minimum at nominal 15% wt. starch but increases at higher starch concentrations. The residual depth in scratching and sliding wear testing has a maximum at 15% starch; there is a minimum of storage modulus E′ determined in dynamic mechanical testing at the same concentration. Microhardness results also reflect the plasticization by MA.     

Characterization,morphology, thermal and mechanical properties of conductive polyaniline‐functionalized EPDM elastomers obtained by casting

Conductive elastomeric blends based on ethylene–propylene–5‐ethylidene–2‐norbornene terpolymer (EPDM) and polyaniline doped with 4‐dodecylbenzenesulfonic acid [PAni(DBSA)] were cast from organic solvents. Functionalization of the elastomer was promoted by grafting with maleic anhydride. Vulcanization conditions were optimized with an oscillating disk rheometer. The conductivity, morphology, thermal stability, compatibility, and mechanical behavior of the obtained mixtures were analyzed by in situ direct current conductivity measurements, atomic force microscopy, transmission electron microscopy, wide‐angle X‐ray scattering, thermogravimetric analysis, differential scanning calorimetry, dynamic mechanical thermal analysis, stress–strain and hysteresis tests. The vulcanization process was affected by temperature, the PAni content, and maleic anhydride. A reinforcement effect was promoted by the vulcanizing agent. The formation of links between the high‐molar‐mass phases and oligomers of PAni(DBSA) in the elastomeric matrix enhanced the thermal stability and ultimate properties of the blends. By the appropriate control of the polymer blends' composition, it was possible to produce elastomeric materials with conductivities in the range of 10^?5–10^?4 S · cm^?1 and excellent mechanical properties. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1767–1782, 2004     

Characterization and thermal stability of PMR polyimides using 7-oxa-bicyclo[2,2,1]hept-5-ene-2, 3-dicarboxylic anhydride as end caps

An anhydride monomer containing ether oxide bridge,7-oxa-bicyclo[2,2,1]hept-5-ene-2,3-dicarboxylic anhydride (ONA),was successfully synthesized by Diels-Alder reaction of furan and maleic anhydride.The ONA was also studied as an end-cap for the polymerization of monomer reactant(PMR) type polyimides.Three molecular weight levels of the ONA end-capped PMR resins were evaluated.The effects of process conditions of these novel PMR resins on thermal and mechanical properties were investigated.It was demonstrated that the imidized prepolymers using the end-cap have good processability,and the cured polyimide specimens exhibited good thermal stability.The initial decomposition temperature, T_d(ca.580℃) and glass transition temperature,T_g(330℃) of the novel resin(PI-20),prepared under optimum process conditions,compare favorably with the T_d(ca.620℃) and T_g(ca.348℃) of the state-of-the-art resin(PI’-20),respectively.