Low power consumption bipolar resistive switching characteristics of ZnO-based memory devices

Ag/ZnO/Pt structure resistive switching devices are fabricated by radio frequency (RF) magnetron sputtering at room temperature. The memory devices exhibit stable and reversible resistive switching behavior. The ratio of high resistance state to low resistance state can reach as high as 10 2 . The retention measurement indicates that the memory property of these devices can be maintained for a long time (over 10 4 s under 0.1-V durable stress). Moreover, the operation voltages are very low, -0.4 V (OFF state) and 0.8 V (ON state). A high-voltage forming process is not required in the initial state, and multi-step reset process is demonstrated. Resistive switching device with the Ag/ZnO/ITO structure is constructed for comparison with the Ag/ZnO/Pt device.     

Interface-engineered resistive switching in Ag/SrTiO3/Nd0.7Ca0.3MnO3/YBa2Cu3O7 heterostructures

For Ag/Nd_0.7Ca_0.3MnO₃/YBa₂Cu₃O₇ (Ag/NCMO/YBCO) heterostructures, we investigate effects of an SrTiO₃ (STO) buffer layer inserted into the Ag/NCMO interface upon the room-temperature resistive switching. In comparison with the non-buffered (Ag/NCMO/YBCO) structure, the insertion of the STO buffer layer can greatly enhance the electric-field-induced-resistance (EPIR) effect. The STO-buffered (Ag/STO/NCMO/ YBCO) device can be switched on-and-off between the higher to lower resistance states at an EPIR ratio of 253% with pulsed voltage ±1.5 V and 405% with pulsed voltage ±3.0 V. The enhanced EPIR ratio is attributed to a combined effect of the migration of oxygen vacancies near the interface and ferroelectric polarization of the STO buffer.     

The effects of substrate temperature on ZnO-based resistive random access memory devices

Ag/ZnO/Zn/Pt structure resistive switching devices are prepared by radio frequency magnetron sputtering.The ZnO thin films are grown at room temperature and 400 C substrate temperature,respectively.By comparing the data,we find that the latter device displayed better stability in the repetitive switching cycle test,and the resistance ratio between a high resistance state and a low resistance state is correspondingly increased.After 104-s storage time measurement,this device exhibits a good retention property.Moreover,the operation voltages are very low:-0.3 V/-0.7 V(OFF state) and 0.3 V(ON state).A high-voltage forming process in the initial state is not required,and a multistep reset process is demonstrated.     

Resistive switching characteristic and uniformity of low-power HfO_x-based resistive random access memory with the BN insertion layer

In this letter,the Ta/HfO_x/BN/TiN resistive switching devices are fabricated and they exhibit low power consumption and high uniformity each.The reset current is reduced for the HfO_x/BN bilayer device compared with that for the Ta/HfO_x/TiN structure.Furthermore,the reset current decreases with increasing BN thickness.The HfO_x layer is a dominating switching layer,while the low-permittivity and high-resistivity BN layer acts as a barrier of electrons injection into TiN electrode.The current conduction mechanism of low resistance state in the HfO_x/BN bilayer device is space-chargelimited current(SCLC),while it is Ohmic conduction in the HfO_x device.     

Role of an oxide interface in a resistive switch

In the present era of data-driven architectures like 5G, Internet of things (IoT), Artificial Intelligence (AI), etc, the requirement of fast-switchable memory storage is more than ever. Oxide resistive switches are considered to be a primary choice in the non-volatile memory design. In this work, we have engineered the conventional metal-insulator-metal (MIM) structure of an oxide memristor (Ag/ZnO/ITO) by inducing an additional oxide layer La_0.7Sr_0.3MnO₃ (LSMO) at the interface between the active layer (ZnO) and Ag electrode. The presence of LSMO acts as a reservoir for the oxygen vacancies, easing the conducting filament formation process in ZnO, thereby enabling drastic improvement of the switching performance and offering reliable endurance over multiple switching cycles. First-principles-based calculations suggested the role of oxygen vacancies in controlling the electronic state of ZnO and formation of vacancies in the resistive switching process, which is in agreement with the experimental observation. The current results pave ways for improving the switching performance of resistive memory circuits through simple structural engineering incorporation, which lies at the heart of oxide electronics.     

Effects of Ag layer and ZnO top layer thicknesses on the physical properties of ZnO/Ag/Zno multilayer system

Two groups of transparent conductive ZnO/Ag/ZnO, ZAZ, multilayer coatings were successively deposited by direct current (DC) magnetron sputtering. Sputtering was carried out from zinc (Zn) and silver (Ag) metallic targets. The effects of Ag layer thickness and ZnO top layer thickness on the properties of the ZAZ multilayer system were examined using different analytical methods. The influences of the Ag layer thickness and ZnO top layer thickness on structural properties were studied using X-ray diffraction. The thicknesses of ZAZ multilayer system were determined using X-ray reflectometry. A sheet resistance of 2.3 Ω/sq at an Ag layer thickness of 17.7 nm was obtained. The sheet resistance changes slightly with ZnO top layer thickness. The optical properties of the films were analyzed. Both Ag layer thickness and ZnO top layer thickness affect transmittance. The optical constants of the ZAZ multilayer system were calculated from transmittance and reflectance measurements. The figure of merit was applied on the ZAZ coatings and the most suitable films for the application as transparent conductive electrodes were determined.     

Bipolar resistive switching in BiFe_(0.95)Zn_(0.05)O_3 films

Bipolar resistive switching is studied in BiFe0.95Zn0.05O3 films prepared by pulsed laser deposition on （001） SrTiO3 substrate, with LaNiO3 as the bottom electrode, and Pt as the top electrode. Multiple steps of resistance change are ob- served in the resistive switching process with a slow voltage sweep, indicating the formation/rupture of multiple conductive filaments. A resistive ratio of the high resistance state （HRS） to the low resistance state （LRS） of over three orders of mag- nitude is observed. Furthermore, the conduction mechanism is confirmed to be space-charge-limited conduction with the Schottky emission at the interface with the top Pt electrodes in the HRS, and Ohmic in the LRS. Impedance spectroscopy demonstrates a conductive ferroelectric/interfacial dielectric 2-layer structure, and the formation/rupture of the conductive filaments mainly occurs at the interfacial dielectric layer close to the top Pt electrodes.     

Performance improvement of amorphous indium–gallium–zinc oxide ReRAM with SiO2 inserting layer

In this study, the resistive switching performance of amorphous indium–gallium–zinc oxide (a-IGZO) resistive switching random-access memory (ReRAM) was improved by inserting a thin silicon oxide layer between silver (Ag) top electrode and a-IGZO resistive switching layer. Compared with the single a-IGZO layer structure, the SiO₂/a-IGZO bi-layer structure exhibits the higher On/Off resistance ratio larger than 10³, and the lower operation power using a smaller SET compliance current. In addition, good endurance and excellent retention characteristics were achieved. Furthermore, multilevel resistance states are obtained through adjusting SET compliance current and RESET stop voltage, which shows a promise for high-performance nonvolatile multilevel memory application.     

Effects of oxygen partial pressure on resistive switching characteristics of ZnO thin films by DC reactive magnetron sputtering

Cu/ZnO/n⁺-Si structures were prepared by magnetron sputtering of a layer of ZnO thin film onto heavily doped silicon substrate, followed by thermal evaporation of a thin layer of metallic Cu. The resistive switching characteristics of Cu/ZnO/n⁺-Si structures were investigated as a function of oxygen partial pressure during ZnO deposition. Reproducible resistive switching characteristics were observed in ZnO thin films deposited at 20%, 33% and 50% oxygen partial pressure ratios while ZnO thin film deposited at 10% oxygen partial pressure ratio did not show resistive switching behavior. The conduction mechanisms in high and low resistance states are dominated by space-charge-limited conduction and ohmic behavior respectively, which suggests that resistive switching behaviors in such structures are related to filament formation and rupture. It is also found that the reset current decreases as oxygen partial pressure increases, due to the variation of oxygen vacancy concentration in the ZnO thin films.     

铜掺杂氧化锌薄膜阻变特性的研究

以 ZnO：Al为底电极,Cu为顶电极,在同种工艺条件下分别制备了类电容结构的纯ZnO 阻变器件和ZnO：2%Cu阻变器件,分析比较了两种器件的典型I-V特性曲线、置位电压（V_Set）和复位电压（V_Reset）的分布范围、器件的耐久性。结果显示,ZnO：Cu阻变器件较纯ZnO阻变器件有更大的开关比和更稳定的循环性能。另外,研究了 ZnO：Cu阻变器件的阻变机理,通过对其I-V特性曲线分析得出以下结论：ZnO：Cu阻变器件在高阻态遵循空间电荷限制电流效应,低阻态符合欧姆定律。     

Top electrode-dependent resistance switching behaviors of lanthanum-doped ZnO film memory devices

Lanthanum-doped ZnO (Zn_0.99La_0.01O) polycrystalline thin films were deposited on Pt/Ti/SiO₂/Si substrates by a chemical solution deposition method. Metal/La-doped ZnO/Pt sandwich structures were constructed by depositing different top electrodes (Ag and Pt). Unipolar switching and bipolar switching characteristics were investigated in Pt/La-doped ZnO/Pt and Ag/La-doped ZnO/Pt structures, respectively. Compared with the undoped devices (Pt/ZnO/Pt and Ag/ZnO/Pt), the La-doped devices exhibits superior resistive switching performances, such as narrow distribution of the resistive switching properties (R _ON, R _OFF, V _Set, and V _Reset), higher R _OFF/R _ON ratio and sharp switching transition.     

氧分压对Ni/HfO_x/TiN阻变存储单元阻变特性的影响

采用射频磁控溅射的方法,基于不同氧分压制备的氧化铪构建了Ni/HfO_x/TiN结构阻变存储单元.研究发现,随着氧分压的增加,薄膜表面粗糙度略有降低;另一方面,阻变单元功耗降低,循环耐受性能可达10~3次,且转变电压分布的一致性得到改善.结合电流-电压曲线线性拟合结果及外加温度测试探究了器件的转变机理,得出在低阻态的传导机理为欧姆传导机理,在高阻态的传导机理为肖特基发射机理,并根据氧空位导电细丝理论,对高低阻态的阻变机理进行了详细的理论分析.     

Resistive switching effect in metal–oxide–metal structures with ZnO:Li oxide layer

The resistive switching effect in metal–oxide–metal (MOM) structures has been investigated, where the 10% Li-doped ZnO layer was used as an oxide layer, as well as Pt and 20% fluorine doped SnO₂ (SnO₂:F) were used as a bottom electrodes. The current–voltage (I–V) and switching (I–t) characteristics of Ag/ZnO:Li/Pt and Ag/ZnO:Li/SnO₂:F structures were investigated. The unipolar resistive switching is detected in the structures with the Pt, while the use of transparent conductive SnO₂:F electrode instead of Pt, results to the bipolar memory effect.     

下电极对ZnO薄膜电阻开关特性的影响

本文采用直流磁控溅射法在三种不同的下电极(BEs)上制备了ZnO薄膜, 获得了W/ZnO/BEs存储器结构. 研究了不同的下电极材料对器件电阻开关特性的影响. 研究结果表明, 以不同下电极所制备的器件都具有单极性电阻开关特性. 在低阻态时, ZnO薄膜的导电机理为欧姆传导, 而高阻态时薄膜的导电机理为空间电荷限制电流. 不同下电极与ZnO薄膜之间的肖特基势垒高度对电阻开关过程中的操作电压有较大的影响, 并基于导电细丝模型对不同下电极上ZnO薄膜的低阻态阻值及reset电流的变化进行了解释. 关键词： ZnO薄膜 电阻开关 下电极     

Resistive switching of in situ and ex situ oxygen plasma treated ZnO thin film deposited by atomic layer deposition

In situ and ex situ oxygen plasma treatment (OPT) were applied to treat ZnO thin films deposited by thermal atomic layer deposition (T-ALD), and the resistive switching (RS) behaviors of the films were investigated. For the in situ OPT, the treatment was applied after each T-ALD cycle. For the ex situ OPT, the treatment was applied on the as-grown film. The T-ALD-grown ZnO films were defect-rich and conductive with no RS behavior. After the OPT process, the resistivity of the films increased drastically, which is believed to be mainly due to the removal of hydrogen impurities, and the films showed bipolar RS characteristics. The dominant conduction mechanisms are the trap-controlled space charge limited current and ohmic behavior at different field regions. The RS behavior was induced upon the formation/disruption of the conducting filaments. Owing to the homogeneous chemical composition and fewer defects, the resistance ratio of the in situ OPT ZnO film is higher than that of the ex situ OPT film, implying that the in situ OPT method is an efficient way to fabricate resistive random access memory devices using the ALD-grown ZnO films.     

Resistive switching characteristics of sol–gel based ZnO nanorods fabricated on flexible substrates

The authors report the resistive switching characteristics of sol–gel based ZnO nanorods (NRs) fabricated on flexible substrates. A resistance ratio of 10, endurance of over 100 cycles, and narrower dispersion in the ON/OFF voltages and resistances compared to ZnO thin‐film devices are demonstrated. Furthermore, the resistive switching characteristics on flexible substrates are maintained under severe substrate bending because of the ductile properties of the nanorods. Devices composed of the Au/sol–gel based NRs/Au structure have the potential for low‐temperature flexible nonvolatile memory applications. (© 2013 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Rectifying resistance switching behaviors of SnO2 microsphere films modulated by top electrodes

Based on the bipolar resistive switching (RS) characteristics of SnO₂ films, we have fabricated a new prototypical device with sandwiched structure of Metal/SnO₂/fluorine-doped tin oxide (FTO). The SnO₂ microspheres film was grown on FTO glass by template-free hydrothermal synthesis, which was evaporated with various commonly used electrodes such as aluminium (Al), silver (Ag), and gold (Au), respectively. Typical self-rectifying resistance switching behaviors were observed for the RS devices with Al and Au electrodes. However, no obvious rectifying resistance switching behavior was observed for the RS device with Ag electrode. Above results were interpreted by considering the different interface barriers between SnO₂ and top metal electrodes. Our current studies pave the ways for modulating the self-rectifying resistance switching properties of resistive memory devices by choosing suitable metal electrodes.     

Influence of oxygen treatment and temperature on electrical properties of the epitaxial Nb-doped SrTiO3 films on silicon

We have fabricated the epitaxial Nb-doped SrTiO3(NbSTO) thin films on Si substrates using a TiN film as the buffer layer.The oxygen-treatment and temperature dependence of electrical properties has been investigated.Oxygen treatment showed the surface change of NbSTO films has immense influence on the resistance switching.The resistance ratio of two resistance states decreased after oxygen treatment.With tested-temperature rising,the resistance and resistance ratio of two resistance states increased.The resistance switching of Pt/NbSTO junction as a function of oxygen-treatment and temperature can be explained by the charge trapping and detrapping process in the Pt/NbSTO interface,which will help understand the resistance switching mechanism of oxides.     

Zinc Oxide Thin Films for Memristive Devices: A Review

Zinc Oxide (ZnO) thin films have been addressed as promising candidates for the fabrication of Resistive Random Access Memory devices, which are alternative to conventional charge-based flash memories. According to the filamentary conducting model and charge trapping/detrapping theory developed in the last decade, the memristive behavior of ZnO thin films is explained in terms of conducting filaments formed by metallic ions and/or oxygen vacancies, and their breaking through electrochemical redox reactions and/or recombination of oxygen vacancies/ions. A comparative review of the memristive properties of ZnO thin films grown by sputtering, atomic layer deposition (ALD), pulsed laser deposition (PLD), and sol-gel methods is here proposed. Sputtered ZnO thin films show promising resistive switching behaviors, showing high on/off ratios (10–10⁴), good endurance, and low operating voltages. ALD is also indicated to be useful for growing conformal ZnO layers with atomic thickness control, resulting in important resistive switching characteristics, such as relatively high on/off ratios and low operating voltages. High insulating epitaxial ZnO thin films can be obtained by PLD, showing reliable switching properties at low voltages and with good retention. On the contrary, the sol-gel approach generally results in ZnO thin films with poor resistive switching behaviors. Nevertheless, thin films derived from ZnO NPs show improved switching performances, with higher on/off ratios and lower operating voltages. Independently of the synthetic approach, doped ZnO thin films exhibit better resistive switching behaviors than pristine ones, coupling a strong increase of the on/off ratio with a more stable switching response.     

Effect of defect content on the unipolar resistive switching characteristics of ZnO thin film memory devices

In this study, unipolar resistive switching (URS) characteristics in ZnO thin film memory devices were systematically investigated with variable defect content. ZnO films displayed typically URS behavior while oxygen-deficient ZnO_1?x films did not show resistive switching effects. The devices with two intentional Ohmic interfaces still show URS. These results show that appearance of URS behavior can be dominated by initial oxygen vacancy content in ZnO thin films. Modest increase in oxygen vacancy content in ZnO films will lead to forming-free and narrower distributions of switching parameters (set and reset voltage, high and low resistance states). It indicates that controlling the initial oxygen vacancy content was an effective method to enhance the URS performance.