Optimization of a microwave-assisted extraction of secondary metabolites from crustose lichens with quantitative spectrophotodensitometry analysis

A focused and rapid microwave-assisted extraction (MAE) process was carried out and optimized for secondary metabolites from crustose lichens using Taguchi experimental design and quantitative analysis on TLC by a Camag^® spectrophotodensitometer. The procedure was improved by quantitative determination of norstictic acid (NA), a common depsidone isolated from Pertusaria pseudocorallina (Sw.) Arn. Various experimental parameters that can potentially affect the NA extraction yields including extraction time, irradiation power, volume and the percentage of tetrahydrofuran (THF) were optimized. Results suggest that THF percentage and solvent volume were statistically the most significant factors. The optimal conditions were determined as follows: THF level of 100%, solvent volume of 15 mL, microwave power of 100 W and extraction time of 7 min. Compared to the reflux method, MAE showed a drastic reduction of extraction time (7 min vs. 3 h) and solvent consumption (15 mL vs. 30 mL). The NA in total yield was 90% using the two methods. The optimal conditions were applied to other crustose lichens, Aspicilia radiosa, Diploicia canescens and Ochrolechia parella for the extraction of NA, diploicine (DP) and variolaric acid (VA), with 83%, 90% and 95% of recovery, respectively.     

Determination of selected polychlorinated biphenyls in water samples by ultrasound-assisted emulsification-microextraction and gas chromatography-mass-selective detection

Ultrasound-assisted emulsification-microextraction (USAEME) procedure was developed for the determination of selected polychlorinated biphenyls (PCBs) in 10 mL of water samples by gas chromatography-mass-selective detection. After determination of the most suitable solvent and extraction time, several other parameters including solvent volume, centrifugation time and ionic strength of the sample were optimized using a 2³ factorial experimental design. The optimized USAEME procedure used 200 μL of chloroform as extraction solvent, 10 min of extraction with no ionic strength adjustment at 25 °C and 5 min of centrifugation at 4000 rpm. The limits of detection ranged from 14 ng L⁻¹ (for PCB153) to 30 ng L⁻¹ (for PCB101). Recoveries of PCBs from fortified distilled water are over 80% for three different fortification levels between 0.1 and 5 μg L⁻¹ and relative standard deviations of the recoveries are below 10%. The performance of the proposed method was compared with those involving traditional liquid-liquid extraction (LLE) and solid phase extraction (SPE) on the real water samples (i.e., tap and well water as well as domestic and industrial wastewaters, etc.) and comparable efficiencies were obtained. The proposed USAEME procedure has been demonstrated to be viable, simple, rapid and easy to use for residue analysis of PCBs in water samples.     

Rapid determination of methyl tert-butyl ether using dynamic headspace/ion mobility spectrometry

Using an original, experimental set-up named dynamic headspace/IMS (DHS/IMS), ppb levels of methyl tert-butyl ether (MTBE), a gasoline additive and environmental pollutant, were determined in drinking and ground water. A portable IMS (Bruker, Raid-1 model) was connected to the outlet of a Drechsel bottle containing 100 ml of water-based sample. Automatically activated to sample air, the IMS built-in pump was used to produce a continuous and gentle air flow bubbling through the water-based sample. This allowed volatile MTBE to be isolated and transferred into the Drechsel headspace and then into the IMS. Analyses of reference solutions and real samples resulted in MTBE detection limits of 20 ppb, calibration curves in the 20-200 ppb range, and relative standard deviations of 4.7 and 8.4%, respectively, for inter- and intra-day reproducibility tests. Detection limits were further improved to 0.5 ppb by means of a Tenax trap cooled with liquid nitrogen, placed between the sample bottle and the IMS. Overall, DHS/IMS could well become a simple and cost-effective tool for rapid and on-line analysis of volatile organic compounds in water.     

Headspace-single drop microextraction (HS-SDME) in combination with high-performance liquid chromatography (HPLC) to evaluate the content of alkyl- and methoxy-phenolic compounds in biomass smoke

The content of ten phenolic compounds present in four different biomass smoke materials: rock rose (Cistus monpelienisis), prickly pear (Opuntia ficus indica), pine needles (Pinus canariensis), and almonds skin (Prunus dulcis), have been evaluated. The sampling method mainly consisted of a trap alkaline solution to solubilize the phenols, and was optimized by an experimental design. Average sampling efficiencies of 78.1% and an average precision value of 10.6% (as relative standard deviation, RSD), were obtained for the selected group of phenols. The trapped phenolates were further analyzed by a headspace-single drop microextraction (HS-SDME) procedure, in combination with high-performance liquid chromatography (HPLC) with UV detection. The optimum variables for the HS-SDME method were: 1-decanol as extractant solvent, 3.5 μL of microdrop volume, 2 mL of sample volume, a pH value of 2, saturation of NaCl, an extraction temperature of 60 °C, and an extraction time of 25 min. The optimized HS-SDME method presented detection limits ranging from 0.35 to 5.8 μg mL⁻¹, RSD values ranging from 0.7 to 7.4%, and an average relative recovery (RR) of 99.8% and an average standard deviation of 5.2. The average content of phenolic compounds in the biomass materials studied were 70, 161, 206 and 252 mg kg⁻¹ of biomass for prickly pear, almonds skin, rock rose, and pine needles, respectively. The main components of the smokes were vanillin, phenol and methoxyphenols, in all smoking materials studied.     

Optimization of microwave-assisted solvent extraction for volatile organic acids in tobacco and its comparison with conventional extraction methods

In the present study, a new method using microwave-assisted solvent extraction (MASE) technique followed directly GC analysis was developed for the extraction of volatile organic acids (VOAs) in tobacco. The MASE conditions (heating time, volume of extracting solvent and extraction temperature) were optimized by means of an orthogonal array design (OAD) procedure. The results suggested that extractant, temperature and heating time were statistically the most significant factors. The extracts were directly analyzed with capillary GC operating in splitless-injection mode on an Agilent HP-FFAP capillary column. Under optimum operating conditions, MASE showed significantly better recoveries than those obtained by the conventional extraction method (ultrasonic and reflux extraction), ranging from 90.6% to 103.2%. In addition, a drastic reduction of the extraction time (20 min versus 4 h) and solvent consumption (20 mL versus 100 mL) was achieved with an outstanding reproducibility (CV ≤5%).     

Speciation of antimony in airborne particulate matter using ultrasound probe fast extraction and analysis by HPLC-HG-AFS

A fast extraction procedure has been developed for Sb(III) and Sb(V) oxoanions speciation in airborne particulate matter samples. Different extraction media (diammonium tartrate, hidroxilammonium clorhidrate, citric acid + ascorbic acid, phosphoric acid and citrate solutions) were tried, with assistance of an ultrasonic probe. The operation power and time of extraction were also optimized. The higher extraction recoveries were obtained with a 100 mmol L⁻¹ hidroxilammonium clorhidrate aqueous solution assisted by the ultrasound probe operated at 50 W during 3 min. The extracts were analyzed by HPLC-HG-AFS. The chromatographic separation of Sb(III) and Sb(V) was also optimized using diammonium tartrate and phthalic acid as mobile phases. The separation of both Sb species was performed in less than 3 min under isocratic conditions, using a 200 mmol L⁻¹ diammonium tartrate solution. The proposed extraction procedure and the HPLC-HG-AFS instrumental coupling have been successfully applied to airborne particulate matter samples, with high Sb content, collected in heavy traffic streets from Buenos Aires (Argentina). The results showed the presence of both Sb species at similar concentrations in the ng m⁻³ level. The extraction yield was higher than 90% for all the analyzed samples.     

Ultrasonic microdialysis coupled with capillary electrophoresis electrochemiluminescence study the interaction between trimetazidine dihydrochloride and human serum albumin

The paper describes a homemade ultrasonic microdialysis device coupled with capillary electrophoresis electrochemiluminescence (CE-ECL) for studying the interaction between human serum albumin (HSA) and trimetazidine dihydrochloride (TMZ). The time required for equilibrium by ultrasonic microdialysis was 45 min, which was far less than that by traditional dialysis (240 min). It took 80 min to achieve the required combination equilibrium by normal incubation and only 20 min by ultrasonic. Compared with traditional dialysis, the use of ultrasonic microdialysis simplified experimental procedures, shortened experimental time and saved consumption of sample. A simple, sensitive and selective determination of TMZ was developed using CE-ECL and the parameters that affected ECL intensity were optimized. Under the optimized conditions, the linear range of TMZ was from 0.075 to 80 μmol/L (r² = 0.9974). The detection limit was 26 nmol/L with RSD of 2.8%. The number of binding sites and binding constant were 1.54 and 15.17 L/mol, respectively.     

Optimization of dispersive liquid-liquid microextraction combined with gas chromatography for the analysis of nitroaromatic compounds in water

Dispersive liquid-liquid microextraction (DLLME) coupled with gas chromatography-flame ionization detector (GC-FID) was developed for preconcentration and determination of some nitroaromatic compounds in wastewater samples. The effects of different variables on the extraction efficiency were studied simultaneously using experimental design. The variables of interest in the DLLME process were extraction and disperser solvent volumes, salt effect, sample volume, extraction temperature and extraction time. A Plackett-Burman design was performed for screening of variables in order to determine the significant variables affecting the extraction efficiency. Then, the significant factors were optimized by using a central composite design (CCD) and the response surface equations were derived. The optimum experimental conditions found from this statistical evaluation included: sample volume, 9 mL; extraction solvent (CCl₄) volume, 20 μL; disperser solvent (methanol) volume, 0.75 mL; sodium chloride concentration, 3% (w/v); extraction temperature, 20 °C and extraction time, 2 min. Under the optimum conditions, the preconcentration factors were between 202 and 314. Limit of detections (LODs) ranged from 0.09 μg L⁻¹ (for 2-nitrotoluene) to 0.5 μg L⁻¹ (for 2,4-dinitrotoluene). Linear dynamic ranges (LDRs) of 0.5-300 and 1-400 μg L⁻¹ were obtained for mononitrotoluenes (MNTs) and dinitrotoluenes (DNTs), respectively. Performance of the present method was evaluated for extraction and determination of nitroaromatic compounds in wastewater samples in the range of microgram per liter and satisfactory results were obtained (RSDs < 10.1%).     

Determination of dimethyl fumarate in desiccant and mouldproof agents using ultrasound-assisted extraction gas chromatography with electron-capture detection

A fast, simple, low cost, and high throughput method has been developed for the determination of dimethyl fumarate (DMF) in desiccant and anti-mould agents employed for protecting clothes, footwear and accessories from humidity and mould. The procedure is based on ultrasound-assisted extraction followed by GC-μECD analysis. The method was conveniently optimized, and the analyte was efficiently extracted from the samples in only 5 min using such a low volume of solvent (ethyl acetate) as 1 mL. Simultaneous extractions could be carried out in also 5 min without loosing efficiency. The method has been validated showing good linearity and selectivity. Precision was satisfactory with RSD of 4–5%. Recovery was evaluated in two real samples at different DMF concentration levels and was >90% in all cases. Limit of detection and quantification were at the ng g⁻¹ level. The proposed procedure was applied to the determination of DMF in several desiccant and anti-mould samples. Although most of them were labelled as “silica gel” all the samples tested with the exception of three presented important amounts of DMF, many of them at the high μg g⁻¹ level. The presence and the high concentrations of this allergenic fungicide in desiccant and anti-mould sachets employed in many consumer products, such as clothes and footwear, should be a matter of concern.     

Application of headspace single-drop microextraction coupled with gas chromatography for the determination of short-chain fatty acids in RuO4 oxidation products of asphaltenes

In this study, headspace single-drop microextraction (HS-SDME) coupled with gas chromatography-flame ionization detection (GC-FID), was employed to determine short-chain fatty acids (SCFAs) in ruthenium tetroxide (RuO₄) oxidation products of asphaltenes. Several significant parameters, such as drop solvent type, drop volume, sample solution ionic strength, agitation speed, extraction time, and ratio of headspace volume to sample volume were optimized. Under optimum extraction conditions (i.e., a 3-μL drop of 1-butanol, 20 min exposure to the headspace of a 6 mL aqueous sample placed in a 10 mL vial, stirring at 1000 rpm at room temperature, and 30% (w/v) NaCl content), the reproducibility and accuracy of the method have been tested and found to be satisfactory. The analysis of a real asphaltene sample using this method proved that HS-SDME can be a promising tool for the determination of volatile SCFAs in complex matrices.     

An ionic liquid as a solvent for headspace single drop microextraction of chlorobenzenes from water samples

A headspace single-drop microextraction (HS-SDME) procedure using room temperature ionic liquid and coupled to high-performance liquid chromatography capable of quantifying trace amounts of chlorobenzenes in environmental water samples is proposed. A Plackett-Burman design for screening was carried out in order to determine the significant experimental conditions affecting the HS-SDME process (namely drop volume, aqueous sample volume, stirring speed, ionic strength, extraction time and temperature), and then a central composite design was used to optimize the significant conditions. The optimum experimental conditions found from this statistical evaluation were: a 5 μL microdrop of 1-butyl-3-methylimidazolium hexafluorophosphate, exposed for 37 min to the headspace of a 10 mL aqueous sample placed in a 15 mL vial, stirred at 1580 rpm at room temperature and containing 30% (w/v) NaCl. The calculated calibration curves gave a high level of linearity for all target analytes with correlation coefficients ranging between 0.9981 and 0.9997. The repeatability of the proposed method, expressed as relative standard deviation, varied between 1.6 and 5.1% (n = 5). The limits of detection ranged between 0.102 and 0.203 μg L⁻¹. Matrix effects upon extraction were evaluated by analysing spiked tap and river water as well as effluent water samples originating from a municipal wastewater treatment plant.     

Fast throughput, highly sensitive determination of allergenic disperse dyes in textile products by use of sample composition

A simple, highly sensitive and fast procedure for the control of allergenic disperse dyes in textile products was optimized. The method is based on ultrasound assisted extraction of textile samples with 20 mL of methanol under controlled conditions (15 min, 70 °C) followed by separation and analysis by LC-MS-MS. The sample preparation process was optimized by means of a surface response experimental design and provided quantitative recoveries of dyes, much better than the poor recoveries provided by current standard procedures. The chromatographic separation was optimized by means of computer-assisted method development by use of a special chemometric tool developed specifically for LC-MS systems, as previously reported by the authors. The result is a rapid chromatographic procedure that enables accurate quantification, at very low concentrations, of all 23 allergenic and/or carcinogenic disperse dyes considered. Matrix effects in the LC-MS procedure were studied. Under the experimental conditions, both conventional and strategic sample composition are proposed as efficient procedures that reduce the costs and work involved in the control of allergenic dyes in finished textile products. The benefits of strategic sample composition are demonstrated by means of an example case study, and the pros and cons of preparing the composite samples from sample extracts or directly from textile products are discussed.     

Dynamic versus static ultrasonic sample treatment for the solid-liquid pre-concentration of mercury from human urine

Dynamic and static ultrasonic procedures involving ultrasonic bath and tandem focused ultrasound (i.e. two probes were used in the same sample treatment) have been assessed in order to implement a reliable solid-liquid back extraction of mercury from commercial resins (dowex and chelex-100), previously used to concentrate Hg(II) from treated urine. The urine had been previously treated with an advanced oxidation process provided by the conjunction of potassium permanganate, hydrochloric acid and high intensity focused ultrasound, which allowed that organic matter degradation was achieved in less than 3 min. 95 ± 10% of mercury in the certified urine and 97 ± 6% of the spiked methyl-mercury was recovered with the dowex resin plus the static ultrasonic procedure, whilst 96 ± 11% of the spiked mercury was recovered with the dowex resin plus the dynamic procedure, for which ultrasonication was not necessary. The Hg pre-concentration factor used in this work was 8 (20 mL of urine to 2.5 mL of acid), but different volume ratios can be used in order to increase this factor.     

Comparative study of the adsorption performance of a multi-sorbent bed (Carbotrap, Carbopack X, Carboxen 569) and a Tenax TA adsorbent tube for the analysis of volatile organic compounds (VOCs)

A comparison between two types of adsorbent tubes, the commonly used Tenax TA and a multi-sorbent bed (Carbotrap, Carbopack X, Carboxen 569) tube developed in our laboratory, has been done to evaluate their usefulness in the analysis of VOCs in ambient air. Duplicate indoor and outdoor samples of Tenax TA and multi-sorbent tubes of 10, 20, 40, 60 and 90 l were taken in Barcelona city (Spain) on July and October of 2009. Breakthrough values (defined as %VOCs found in the back tube) were determined for all sampling volumes connecting two sampling tubes in series. The analysis was performed by automatic thermal desorption (ATD) coupled with capillary gas chromatography (GC)/mass spectrometry detector (MSD). Significant differences between the concentrations obtained-from multi-sorbent bed and Tenax TA tubes are observed for the very volatile compounds (56 °C < boiling point < 100 °C and 4 kPa < vapour pressure (20 °C) < 47 kPa) (e.g. acetone, isopropanol, n-hexane) and for alcohols and chlorinated compounds (e.g. 1-butanol, carbon disulphide, dichloromethane, chloroform, carbon tetrachloride, trichloroethylene, tetrachloroethylene), being the concentrations found higher in multi-sorbent bed than in Tenax TA tubes. On the other hand, mainly all compounds with boiling points higher than 100 °C (except α-pinene, chlorinated and polar compounds) do not show significant differences between the obtained multi-sorbent bed and Tenax TA tube concentrations. For the concentrations obtained (5 ppt to 100 ppb), Tenax TA present high breakthrough values (from 0 to 77%) for mainly all compounds and sampling volumes studied. On the other hand, multi-sorbent bed tubes do not exhibit important breakthrough values for these compounds, except the VVOCs ethanol (for all sampled volumes), and acetone, dichloromethane and isopropanol (for sampling volumes over 40 l). The concentration differences observed between Tenax TA and multi-sorbent bed tubes are directly related to the high breakthrough values determined for Tenax TA adsorbent.     

Carbon nanocones/disks as new coating for solid-phase microextraction

In this article, the potential of carbon nanocones/disks as coating for solid-phase microextraction has been evaluated for the first time. The nanostructures were immobilized on a stainless steel needle by means of an organic binder. The fiber coating obtained was ca. 50 μm of thickness and 35 mm in length. The evaluation of the sorbent capacity was carried out through the determination of toluene, ethylbenzene, xylene isomers and styrene in water samples following the headspace sampling modality (15 min, 30 °C). The fiber was then transferred to a 10 mL vial which was sealed and heated at 110 °C for 15 min in the headspace module of the instrument to achieve the thermal desorption of the analytes. Then 2.5 mL of the headspace generated were injected in the gas chromatograph-mass spectrometer for analytes separation and quantitation. The detection and quantitation limits obtained for 10 mL of sample were 0.15 and 0.5 ng mL⁻¹ (0.6 and 2 ng mL⁻¹ for toluene). The optimized procedure was applied to the determination of the selected volatile compounds in waters collected from different locations. The recovery values obtained (average recovery ca. 92%) demonstrated the usefulness of the carbon nanocones/disks as sorbent material in solid-phase microextraction.     

Pressurized liquid extraction of organophosphate triesters from sediment samples using aqueous solutions

A novel procedure for the extraction of seven organophosphate triesters (OPs), used as flame retardants and plasticizers, from sediment samples has been developed. It is based on the pressurized liquid extraction of the analytes with aqueous solutions, combined with a further concentration step using solid-phase extraction (SPE) and followed by gas chromatography coupled to mass spectrometry (GC-MS) determination. The effects of different variables on the yield and selectivity of the sample preparation process are systematically evaluated. The optimal responses were observed extracting 2 g of sediment with a water:acetonitrile (75:25) solution at 90 °C and 1500 psi for 5 min. The obtained extract was made up to 200 mL with ultrapure water and passed through an OASIS HLB, 60 mg cartridge. Analytes were recovered with 2 mL of ethyl acetate and this extract concentrated to a lower volume, ca. 0.2 mL. Recoveries of the proposed extraction method ranged from 77 to 111%, with relative standard deviations below 10%, for spiked river and marine sediment samples with total carbon contents (TC) up to 4.0%. The limits of quantification (LOQs) of the method varied between 0.5 and 5 ng g⁻¹. Analysis of non-spiked sediment samples revealed the presence of low levels for some of the investigated species, with the highest concentration (47 ng g⁻¹) corresponding to tris(2-chloroethyl) phosphate (TCEP).     

Microwave assisted extraction of iodine and bromine from edible seaweed for inductively coupled plasma-mass spectrometry determination

The feasibility of microwave energy to assist the solubilisation of edible seaweed samples by tetramethylammonium hydroxide (TMAH) has been investigated to extract iodine and bromine. Inductively coupled plasma-mass spectrometry (ICP-MS) has been used as a multi-element detector. Variables affecting the microwave assisted extraction/solubilisation (temperature, TMAH volume, ramp time and hold time) were firstly screened by applying a fractional factorial design (2^5-1 + 2), resolution V and 2 centre points. When extracting both halogens, results showed statistical significance (confidence interval of 95%) for TMAH volume and temperature, and also for the two order interaction between both variables. Therefore, these two variables were finally optimized by a 2² + star orthogonal central composite design with 5 centre points and 2 replicates, and optimum values of 200 °C and 10 mL for temperature and TMAH volume, respectively, were found. The extraction time (ramp and hold times) was found statistically non-significant, and values of 10 and 5 min were chosen for the ramp time and the hold time, respectively. This means a fast microwave heating cycle. Repeatability of the over-all procedure has been found to be 6% for both elements, while iodine and bromine concentrations of 24.6 and 19.9 ng g⁻¹, respectively, were established for the limit of detection. Accuracy of the method was assessed by analyzing the NIES-09 (Sargasso, Sargassum fulvellum) certified reference material (CRM) and the iodine and bromine concentrations found have been in good agreement with the indicative values for this CRM. Finally, the method was applied to several edible dried and canned seaweed samples.     

Application of surfactant assisted dispersive liquid-liquid microextraction for sample preparation of chlorophenols in water samples

A simple, rapid, and efficient method, based on surfactant assisted dispersive liquid-liquid microextraction (SA-DLLME), followed by high performance liquid chromatography (HPLC) has been developed for the extraction and determination of chlorophenols as model compounds in environmental water samples. A conventional cationic surfactant called cethyltrimethyl ammonium bromide (CTAB) was used as a disperser agent in the proposed approach. Thirty-five microliter of 1-octanol as an extraction solvent was injected rapidly into 11 mL aqueous sample containing 0.09 mmol L⁻¹ of CTAB, the mixture was then shaken for 3 min to disperse the organic phase. Having the extraction procedure been completed, the mixture was centrifuged and 20 μL of collected phase was injected into HPLC for subsequent analysis. Some parameters such as the type and volume of the extraction solvent, the type and concentration of surfactant, pH, ionic strength, shaking time, extraction temperature and centrifugation time were optimized. The preconcentration factors (PFs) in a range of 187-353 were obtained under the optimum conditions. The linear range, detection limit (S/N = 3), and precision (n = 5) were 0.2-200, 0.1 μg L⁻¹, and 4.7-6.9%, respectively. Tap water, sea water and mineral water samples were successfully analyzed for the existence of chlorophenols using the proposed method.     

Determination of herbicides by solid phase extraction gas chromatography-mass spectrometry in drinking waters

A solid phase extraction (SPE) method has been optimized for the gas chromatography-mass spectrometry (GC-MS) simultaneous determination of herbicides belonging to the following different families: carbamate (molinate), atrazines (atrazine, propazine, simazine, ametryne, cyanazine, terbutylazine, deethylterbutylazine, deethylatrazine), dinitroaniline (trifluralin, pendimethalin), chloroacetamide (alachlor, metolachlor). Different solid substrates have been compared (C18, cyano, styrene-divinylbenzene, phenyl, graphitic carbon). The type of conditioning and elution solvent, its volume, and the sample flow rate have been considered as variables affecting the recovery yields of the herbicides.The optimized experimental conditions are C18 phase conditioned with 3 mL acetone, loaded with 1 L water sample at 5 mL min⁻¹, and eluted with 3 mL acetone. Good recoveries (included between 79% and 99%) and R.S.D. (included between 2% and 12%) have been obtained for all analytes, except for deethylatrazine whose recovery was 46 ± 7%. The recovery of deethylatrazine increases up to 94 ± 17% if a non-porous graphitic carbon is coupled to the C18 phase, keeping the other parameters constant as optimized. The optimized method has been successfully checked for the identification and quantitation of the selected herbicides in raw and drinking water samples, with quantitation limits as low as 0.01 μg L⁻¹, fully in agreement with the current legislation. The method is easily routinable. After development, the method is currently routinely applied for the analysis of herbicides in waters and, up today, more than one thousand samples have been analysed at the “Laboratorio della Società Metropolitana Acque di Torino” (Laboratory of the Municipal Waterworks of Turin) in charge of the control of drinking water quality in Torino.     

Improved determination of selenium in plant and peat samples using hydride generation-atomic fluorescence spectrometry (HG-AFS)

A robust, accurate and sensitive analytical procedure for the determination of Se in plant and peat samples by hydride generation-atomic fluorescence spectrometry (HG-AFS) was developed. Aliquots (200 mg) of dried samples were digested with 3 mL nitric acid and 0.5 mL hydrogen peroxide in closed, pressurized PTFE vessels in a microwave oven at 220 °C. Addition of HBF₄ or HF to the digestion mixture was not required because experiments demonstrated that Se was not hosted in the silicate fraction of the investigated sample matrices. Selenium(VI) was directly reduced to Se(IV) in the undiluted digestion solutions after addition of 3.8 mL of 4 M HCl in a microwave oven at 103 °C for 3 min. Other reduction reagents, such as hydroxylamine hydrochloride or urea, were not necessary to cope with potential interferences from nitrogen oxides that could hamper the reliable determination of Se by HG-AFS. Optimum hydride generation of Se was achieved by using 0.9% NaBH₄ and 4.5 M HCl. A solution detection limit of 11 ng L⁻¹ was obtained under the optimized experimental conditions which corresponds to a method detection limit of 2.8 ng g⁻¹ in solid peat and plant materials. The precision of replicate measurements was better than 3% at Se concentrations of 50 ng L⁻¹. The analytical procedure was critically evaluated by analysing two certified plant reference materials (SRM 1515 Apple Leaves and SRM 1547 Peach Leaves) as well as three peat reference materials. Excellent agreement between the experimental values ranging from 50 ng g⁻¹ to ∼2 μg g⁻¹ and the certified concentrations was obtained.