Determination of fat content and fatty acid composition in meat and meat products after supercritical fluid extraction

Two different relatively simple, commercially available supercritical fluid extractors (SFE), Leco and Foss-Tecator, were tested for the determination of total fat content in meat and meat products. The fatty acid composition in meat and meat products was also determined after the Foss-Tecator extraction in an aliquot of the extract. Total fat was determined by weighing after the different extraction procedures and the fatty acid composition by gas chromatography after hydrolysis and methylation of the extract. The results for total fat content agreed well with results from a standard method of Schmid, Bondzynski, and Ratzlaff, which uses conventional solvent extraction. Fatty acid composition was compared with the Bligh and Dyer extraction, and showed good agreement. The average relative difference between SFE and Bligh and Dyer of all fatty acids in the sample was <3% for acids exceeding 0.5% of total fatty acid amount. The advantages of SFE over traditional methods are a much lower consumption of hazardous organic solvents and shorter extraction times. To obtain quantitative recoveries by SFE, ethanol was added to the extraction cells before extraction.     

Determination of atractylon in Atractylodes rhizome using supercritical fluid chromatography on-line coupled with supercritical fluid extraction by the direct induction method

Atractylon was extracted from Atractylodes rhizome within 15 s with supercritical carbon dioxide. The extraction was so rapid that SFE extracts could be transported directly into an SFC column and analyzed. Atractylon was eluted and separated in ca. 5 min. Analyte recovery was 30% higher than when using solvent extraction. Determination of atractylon in Atractylodes rhizome was achieved with only a few mg of crude drug sample. Atractylon is unstable due to oxidation and is easily transformed to atractylenolides. Loss of analytes during the procedures was also minimal with this on-line SFE–SFC system.     

Determination of total fat in milk- and soy-based infant formula powder by supercritical fluid extraction

Commercially available simple benchtop systems using CO2 supercritical fluid extraction (SFE) eliminate expensive organic solvent disposal problems and offer potential to meet a demand for rapid, accurate high-volume gravimetric determinations of total fat content of infant formula powders. A Data Quality Objectives (DQOs) approach was used to evaluate the performance characteristics of instrumental SFE extraction for determination of total gravimetric fat in infant formula. The established DQOs included the following: ACCURACY: Correct values were obtained for a suitable reference material, SRM 1846 Infant Formula [National Institute of Standards and Technology (NIST), Gaithersburg, MD]. RUGGEDNESS: Variables were defined as (1) extraction time (35 min optimum); (2) ratio of sample size to diatomaceous earth support material (1 g sample/2 g support); (3) ratio of distilled water to alcohol (50% isopropanol optimum for both milk- and soy-based infant formula samples); (4) extraction flow rate was 3-3.5 mL/min optimum. PRECISION: Relative standard deviations of multiple determinations fell within the Horwitz limits of acceptability of < or = 2.8% at the level of analyte determined (0.34-2.5% obtained). SCOPE OF APPLICABILITY: Includes milk- and soy-based infant formula powders. Research data were obtained by use of a commercially available fat analyzer. Samples of the SRM, 2 commercial milk-based and 3 commercial soy-based infant formula products were distributed to 2 additional collaborating laboratories. Very good agreement was obtained among the submitting and collaborating laboratories for these samples. The use of clearly defined DQOs to establish method performance characteristics, along with the commercially available reference material, provided the mechanism for verification and validation of analytical methodology.     

Determination of fat in leather by the use of supercritical fluid extraction combined with on-line piezoelectric detection.

Leather samples were prepared and characterized as 'in house' matrix standards for the determination of fat. The Soxhlet standard method was used to establish the reference fat content in every standard sample. Sample homogeneity and stability were examined under specific storing conditions. The materials were subsequently used as matrix standards for the determination of fat in leather samples, using supercritical fluid extraction (SFE) with on-line piezoelectric detection. Real samples were weighed in the extraction SFE thimble, previously loaded with 1 g of diatomaceous earth. A temperature of 45 degrees C and a CO2 fluid density of 0.85 g ml-1 were used for extraction. The linear calibration range thus achieved was 0.001-0.040% m/m total fat (related to the weight of the leather) and the relative standard deviation +/- 3% (n = 11; P = 0.05). The results were compared with those obtained with the Soxhlet method and no significant differences were found.     

Determination of acetyl gestagenic steroids in kidney fat by automated supercritical fluid extraction and liquid chromatography ion-trap mass spectrometry

Acetyl gestagenic steroids are isolated from animal tissues such as bovine kidney fat by automated supercritical fluid extraction (SFE). After the addition of internal standards and sample pretreatment, the analytes are extracted from the matrix by supercritical CO2 and trapped directly in-line on alumina placed in the extraction vessel. The samples are analysed by liquid chromatography combined with ion-trap mass selective detection (LC-MSn). For quantification, deuterated internal standards are added and single ions of the analytes and internal standards are monitored. For confirmation of the identity of the analytes, two transition ions (one MS2 and one MS3) were monitored and the ratios between the ions were calculated and compared with those of standards. The detection capability for the multi-analyte LC-MSn analysis of megestrol acetate (MA), medroxyprogesterone acetate (MPA), chlormadinone acetate (CMA) and melengestrol acetate (MGA) is 0.5 microg kg(-1). The mean within-laboratory reproducibility ranges from 16-19% (%RSD) at a concentration level of 0.5 microg kg(-1) (n = 9). Running the SFE procedure overnight allows the analysis of 24 samples of fat per day.     

Determination of N-nitrosamines in latex by sequential supercritical fluid extraction and derivatization

A new method to determine N-nitrosamines in latex products has been developed by combination of supercritical fluids and chemical derivatization. A new design for a liquid trap has been introduced. A factorial fractional design was used in order to evaluate the influence of the different factors affecting the process. Factors such as pressure, temperature, static and dynamic time, restrictor temperature and volume of an hydrobromic acid-acetic anhydride mixture (1:10, v/v) were included in the design. CO2 was used as the extraction fluid. Gas chromatography with nitrogen and phosphorus sensitive detection was employed to achieve good sensitivity attending to the molecular structure of these compounds (N-nitrosamines and their corresponding secondary amines). The obtained results have shown to be useful to increase selectivity and reduce sample handling.     

超临界CO2萃取香草兰化学成分分析

香草兰 ,学名 :ＶａｎｉｌｌａｐｌａｎｉｆｏｌｉａＡｎｄｒ.,又名香荚兰 ,香子兰 ,属兰科香子兰属 ,是一种名贵的多年生热带藤本植物 ,有独特的香味 ,被称誉为“食品香料之王”。香草兰经加工后 ,是食品工业的重要天然香料 ,也用于烟草业、化妆品业和药物[1,2 ] 。香草兰原产于墨西哥 ,主产国还有马达加斯加、印尼、牙买加等[3 ] 。近年来 ,我国海南、云南等地也大力种植和推广。超临界流体萃取 (ＳｕｐｅｒｃｒｉｔｉｃａｌＦｌｕｉｄＥｘｔｒａｃｔｉｏｎ ,简称ＳＣＦＥ)是近 2 0年发展起来的现代提取分离技术 ,具有工艺简单、成本低、…     

Utilization of fat retainers in supercritical fluid extraction for the selective extraction of polychlorinated biphenyls from a model fat sample

Two common fat retainers used in supercritical fluid extraction--basic alumina and the silica based adsorbent Florisil--were investigated using lard fat as model material. With a fat retainer in the extraction cell it was possible to obtain fat-free time windows. Activation by heating did not influence the length of the time windows, while deactivation of the retainers with 10% water (w/w) drastically decreased the fat retaining capabilities. The influence of modifier addition was also investigated. Finally, a method was developed, where basic alumina was utilized to selectively extract polychlorinated biphenyls (PCBs) from a model fat sample, containing PCBs, triglycerides and phospholipids. The PCBs could be quantitatively extracted in a totally fat-free time window.     

Determination of benzophenones in a cosmetic matrix by supercritical fluid extraction and capillary electrophoresis

Benzophenones are common additives in commercial sunscreen products. These UV absorbers were extracted by supercritical fluid extraction (SFE), and then analyzed by capillary zone electrophoresis (CZE) and high-performance liquid chromatography. This study was applied to identify the contents of benzophenones in cosmetic matrix, and simultaneously, to investigate the behavior of migration in CZE. Adding non-ionic surfactant (Tween 20) to optimize the separation in the CZE operation improves resolution. In SFE, we chose carbon dioxide with 2.5% modifier of 10% aqueous phosphoric acid-MeOH (1:1) as the supercritical fluid. Real recoveries of up to 92% with relative standard deviations of less than 4.0% were achieved. These analytical techniques were also applied to assay benzophenones for ten commercial sunscreen cosmetics. We found benzophenone 3 was the most commonly used sunscreen additive in Taiwan.     

Development of an automated method for determining oil in water by direct aqueous supercritical fluid extraction coupled on-line with infrared spectroscopy

A direct aqueous supercritical fluid extraction (SFE) system was developed which can be directly interfaced to an infrared spectrometer for the determination of oil in water. The technique is designed to provide an environmentally clean, automated alternative to established IR methods for oil in water analysis which require the use of restricted organic solvents. The SFE-FTIR method involves minimum sample handling stages, with on-line analysis of a 500 ml water sample being complete within 15 min. Method accuracy for determining water samples spiked with gasoline, white spirit, kerosene, diesel or engine oil was 81-100% with precision (RSD) ranging from 3 to 17%. An independent evaluation determined a 2 ppm limit of quantification for diesel in industrial effluents. The results of a comparative study involving an established IR method and the SFE-FTIR method indicate that oil levels calculated using an accepted equation which includes coefficients derived from reference hydrocarbon standards may result in significant errors. A new approach permitted the derivation of quantification coefficients for the SFE-FTIR analyses which provided improved results. In situations where the identity of the oil to be analysed is known, a rapid off-line SFE-FTIR system calibration procedure was developed and successfully applied to various oils. An optional in-line silica gel clean-up procedure incorporated within the SFE-FTIR system enables the same water sample to be analysed for total oil content including vegetable oils and selectively for petroleum oil content within a total of 20 min. At the end of an analysis the SFE system is cleaned using an in situ 3 min clean cycle.     

Determination of sunscreen agents in cosmetic products by supercritical fluid extraction and high-performance liquid chromatography

A rapid supercritical fluid extraction (SFE) procedure for the isolation of five of the most common sunscreen agents (2-ethylhexyl-p-dimethylaminobenzoate, 2-hydroxy-4-methoxybenzophenone, 2-ethylhexyl-p-methoxycinnamate, 4-methylbenzylidene camphor and 4-tert.-butyl-4′-methoxydibenzoylmethane) from cosmetic products is described. Investigation of the factors affecting the extraction efficiency in SFE indicated that sunscreen recoveries were affected mainly by the supercritical CO₂ pressure and by the trapping method. The sunscreens were analyzed by reversed-phase high-performance liquid chromatography after a 10-min extraction of the cosmetic product with CO₂ at 250 bar and 40°C, using sequential glass surface and C₁₈ sorbent as collection system. A quantitative comparison of SFE with a liquid extraction procedure was performed on commercial cosmetics. The SFE method yielded recoveries higher than 94.8% compared with conventional liquid extraction and exhibited a precision better than 5.3% relative standard deviation. Moreover, SFE minimized sample handling, reduced the consumption of harmful solvents and afforded a more effective purification of the cosmetic matrices.     

Determination of anabolic steroids in creatine nutritional supplements after supercritical fluid extraction

The effects of various parameters, i.e. extraction pressure, temperature, time, and modifier on the efficiency of extraction were investigated using an analytical-scale supercritical fluid extraction system. An optimal set of conditions for the extraction and determination by gas chromatography-mass spectrometry of trimethylsilyl derivatives of 4-androstene-3,17-dione, 1,4-androstadiene-3,17-dione, nandrolone, and testosterone in nutritional supplements was developed. The optimum amount of creatine supplement was 1 g, while the optimum pressure and temperature were determined to be 35 MPa and 80 °C, respectively. The optimum dynamic extraction time was 45 min. The limit of detection (LOD) of the investigated compounds ranged from 5 to 25 ng · g⁻¹ of supplement, while recoveries ranged from 76.1 to 86.6%. Correspondence: Petra Mikulcikova, Department of Analytical Chemistry, Faculty of Chemical Technology, University of Pardubice, nám. Cs. Legií 565, CZ 532 10 Pardubice, Czech Republic     

Collection in analytical-scale supercritical fluid extraction

This review is a comprehensive summary of available collection techniques in supercritical fluid extraction (SFE), with emphasis on which parameters are especially important for a successful analyte collection. Environmental, biological and agricultural applications, including several types of sample matrices and analyte groups, are discussed with respect to choice of collection mode and optimization of collection conditions. This review also includes discussions about collection when a modifier is used or when the sample contains large amounts of fat or water, as well as possibilities to achieve enhanced selectivity.     

Chemicals from forest products by supercritical fluid extraction

Supercritical acetone or methanol extraction of wood gave liquid products with a maximum yield of 74%. Approximately 5% of these complex products was identified as substituted guaiacols and levoglucosan. Acetone extract could substitute for 30% of the phenol in phenolic resins.

Resin and fatty acids were extracted from southern pine and waxes from Douglas-fir bark using supercritical carbon dioxide, nitrous oxide, propane or ethylene. Of these, propane and nitrous oxide gave the best yields.     

Analysis of organic pollutants in sewage by supercritical fluid extraction

Summary Analytical methods have been developed for the determination of organic pollutants of intermediate polarity in sewage. Water samples are first passed through a solid phase adsorption cartridge. The analytes are then extracted from the absorbent with supercritical CO₂ into a small volume of trapping solvent. Finally, the extracts are analyzed directly by capillary gas chromatography and gas chromatography-mass spectrometer. The various parameters (pressure, temperature, type and concentration of modifiers, trapping solvent, flow rate and volume of supercritical fluid and equilibrium time) influencing the efficiency of extraction were studied. Extraction efficiencies for the test compounds are >70%, and relative standard deviations are <4.6% (n=3). The methods established were applied to the analysis of sewage at the Lanzhou Wastewater Treatment Plant, China. 66 organic pollutants were detected, of which 15 compounds appeared in the list of priority pollutants suggested by the US EPA.     

Enrichment of tocopherols in wheat germ by directly coupled supercritical fluid extraction with semipreparative supercritical fluid chromatography

Enrichment of tocopherol by coupled supercritical fluid extraction/preparative supercritical fluid chromatography is described. Wheat germ powder is used as the starting material and is subjected to supercritical fluid extraction with carbon dioxide. The extracted oil containing tocopherols is concentrated and trapped on a silica gel column by reducing the pressure of carbon dioxide. The trapped oil is then eluted and separated on a silica gel column of 20 mm i.d. x 20 mm length. The column effluent is fractionated by monitoring UV absorption at 290 nm. With this method, tocopherol content of the wheat germ is enriched 100-fold.     

Some applications of supercritical fluid extraction

Supercritical fluid extraction (SFE) exploits the solvation power of fluids at temperatures and pressures close to their critical point. Use of SFE with supercritical CO₂ is reported for the extraction of caffeine and quinine from various plant materials and of morphine from serum. Results are compared with those obtained by extractions with subcritical methanol and tetrahydrofuran, normal organic Soxhlet extractions and solid-phase extraction.     

Improved supercritical fluid extraction of sulphonamides

Summary Different ways used for enhancing the yield of sulphonamides leached from solid supports are reported. Supercritical CO₂ and methanol-modified CO₂ were used as extractants of the target analytes and the impregnation of the solid sample with buffer, derivatization of the analytes and ion-pair formation were assessed. Only the sulphonamide/tetramethyl-ammonium ion-pairs are quantitatively extracted from the solid supports using pure supercritical CO₂, while the other modifications and the presence of a cosolvent lead to recoveries lower than 30% for most of the analytes. Individual separation/quantitation of the analytes was performed off-line using a liquid chromatograph.     

Determination of major aromatic constituents in vanilla using an on‐line supercritical fluid extraction coupled with supercritical fluid chromatography

An on‐line supercritical fluid extraction coupled with supercritical fluid chromatography method was developed for the determination of four major aromatic constituents in vanilla. The parameters of supercritical fluid extraction were systematically investigated using single factor optimization experiments and response surface methodology by a Box–Behnken design. The modifier ratio, split ratio, and the extraction temperature and pressure were the major parameters which have significant effects on the extraction. While the static extraction time, dynamic extraction time, and recycle time had little influence on the compounds with low polarity. Under the optimized conditions, the relative extraction efficiencies of all the constituents reached 89.0–95.1%. The limits of quantification were in the range of 1.123–4.747 μg. The limits of detection were in the range of 0.3368–1.424 μg. The recoveries of the four analytes were in the range of 76.1–88.9%. The relative standard deviations of intra‐ and interday precision ranged from 4.2 to 7.6%. Compared with other off‐line methods, the present method obtained higher extraction yields for all four aromatic constituents. Finally, this method has been applied to the analysis of vanilla from different sources. On the basis of the results, the on‐line supercritical fluid extraction‐supercritical fluid chromatography method shows great promise in the analysis of aromatic constituents in natural products.