Effects of sampling methodologies on FT-IR data base searching

The sampling methodologies employed in Fourier Transform Infrared (FT-IR) spectroscopy tend to distort to a degree the data obtained relative to that which would be obtained via transmittance. This distortion complicates data base searching. A standard sample of polystyrene was investigated using the techniques of transmittance, attenuated total reflectance (ATR), diffuse reflectance (DRIFT) and photoacoustic spectroscopy (PAS). Several types of corrections are employed to minimize the distortions due to sampling methodologies.These corrections are evaluated with respect to four distinct search algorithms. The results obtained indicate that proper mathematical treatment of the data prior to data base searching enhances the discrimination value of a data base search.     

Self-similar power transforms in extrapolation problems

A method is suggested allowing for the improvement of accuracy of self-similar factor and root approximants, constructed from asymptotic series. The method is based on performing a power transforms of the given asymptotic series, with the power of this transformation being a control function. The latter is defined by a fixed-point condition, which improves the convergence of the sequence of the resulting approximants. The method makes it possible to extrapolate the behaviour of a function, given as an expansion over a small variable, to the region of the large values of this variable. Several examples illustrate the effectiveness of the method     

FT-IR analysis of single human normal and leukemic lymphocytes

The infrared spectra of single human normal and leukemic lymphocytes have been obtained by means of the microscope-FT-IR system. Substantial differences between the two kinds of cells have been observed at level of the O-P-O vibrations of the DNA and of the proteic components. This determination opens up the possibility in determining the early stages of leukemia, in following the course of patients under therapy, and in evaluation of the residual neoplastic disease.     

FT-IR差谱法测定改性聚苯乙烯组成

本实验利用NICOLET 7199 FT-IR仪器,采用二次扣减法完成了低含量聚丁二烯改性的聚苯乙烯样品组成的定量分析。当苯乙烯含量在90～95%范围以内,标准误差小于±0.3%时,苯乙烯含量相对误差小于1%,丁二烯含量相对误差小于10%。     

FT-IR/PAS investigation of solid fuels and catalysts

Coal and catalysts are examples of substances of great technical importance, whose knowledge has advanced for many years empirically. They are considered as disordered and complex materials. FT-IR/PAS suggests models closer to the real systems as the samples can be examined as they are: coal with the same sampling procedure as for ASTM analysis and catalysts during catalysis without manipulation. Some examples are reported.     

Infinite Basis set extrapolation for Double Hybrid Density Functional Theory 1: effect of applying various extrapolation functions

We applied the Infinite Basis (IB) set extrapolation and Double Hybrid Density Functional Theory (DHDF) to calculate the databases of atomization energies, ionization energies, electron affinities, reaction barrier heights, proton affinities, alkyl bond dissociation energies, and noncovalent interactions. The Complete Basis Set (CBS) limit is estimated by extrapolating the hybrid density functional theory and PT2 energies using extrapolation functions including exponential, inverse power, modified exponential, and the combination of the these functions. We found that the combination of B2KPLYP/cc-pV[D|T]Z (which is the extrapolation based on the energies calculated in cc-pVDZ and cc-pVTZ) gives results in quadruple-ζ quality. However, if we want to reach the ～2 kcal/mol chemical accuracy limit, the cc-pV[T|Q]Z is required. Similar results with various extrapolation functions obtained, because the IB parameters were determined by minimizing the averaged mean unsigned error of the calculated databases. We generalized the IB set extrapolation to include more than two basis sets, but we found that extrapolation with two basis sets is satisfactory to give reasonable results. The largest error occurred in the databases of the electron affinities and the weak interactions between the noble gas and the nonpolar molecules. We expect that performing the DHDF-IB scheme with the basis sets augmented by diffuse basis functions will further improve the results.     

Preparation and FT-IR spectra of calcium bilirubinate

In this investigation two calcium bilirubinates compounds, Ca(HBR)₂·H₂O and Ca(BR)·2H₂O, were prepared. Their Fourier transform infrared spectra were measured in KBr discs and in fluorolube and nujol mulls, respectively. The results suggest that it is better to identify the Ca(HBR)₂·H₂O and Ca(BR)·2H₂O with fluorolube and/or nujol mulls when examining mixtures (e.g. gallstone).     

水合硼氧酸盐结晶过程中液相的红外光谱

使用差示红外光谱的方法记录了MgB4O7.9H2O,NaB5O8.5H2O,MgB6O10.7H2O和MgB6O10.7.5H2O过饱和水溶液结晶析出相应固相时液相中多聚硼氧配阴离子的变化。结果得出,硼氧酸盐水溶液的红外光谱在800－1000cm^-1波数范围内,存在多种多聚硼氧配阴离子的特征峰,并对振动光谱频率进行了归属。870,810cm^-1为三硼氧配阴离子特征峰;844cm^-1为四硼氧配阴离子特征峰;929cm^-1为五硼氧配阴离子特征峰;959cm^-1为六硼氧配阴离子的特征峰。     

Microencapsulated Red Powders from Cornflower Extract—Spectral (FT-IR and FT-Raman) and Antioxidant Characteristics

Although the health benefits of cornflower extracts are known, their application in food production has not been widely investigated. This study assessed microencapsulated red powders (RP) prepared from the aqueous extract of blue cornflower petals. Microencapsulation was performed by freeze-drying using various stabilizers, such as maltodextrin, guar gum, and lecithin. The microencapsulated RP were characterized by spectral (FT-IR and FT-Raman), mineral, structural, and antioxidant analyses. The FT-IR and FT-Raman band related to guar gum, lecithin, and maltodextrin dominated over the band characteristic of anthocyanins present in the cornflower petal powders. The main difference observed in the FT-Raman spectra was attributed to a shift of bands which is reflection of appearance of flavium cation forms of anthocyanins. The microencapsulated RP had total phenolic content of 21.6–23.4 mg GAE/g DW and total flavonoid content of 5.0–5.23 mg QE/g. The ABTS radical scavenging activity of the tested powders ranged from 13.8 to 20.2 EC₅₀ mg DW/mL. The reducing antioxidant power (RED) of the powders was estimated at between 31.0 and 38.7 EC₅₀ mg DW/mL, and OH^• scavenging activity ranged from 1.9 to 2.6 EC₅₀ mg DW/mL. Microencapsulated cornflower RP can be valuable additives to food such as sweets, jellies, puddings, drinks, or dietary supplements.     

Thermal degradation of polyesters by simultaneous TG-DTA/FT-IR analysis

A combination system of thermogravimetric/differential thermal analysis (TG-DTA) and Fourier-transform infrared absorption spectroscopy (FT-IR) was described. This simultaneous TG-DTA/FT-IR technique gave spectroscopic and weight loss information about the thermal degradation process of engineering polyesters; poly(ethylene terephthalate)(PET) and poly(butylene terephthalate)(PBT). The evolved gases from PET were benzoic acid, carbon dioxide and carbon monoxide, while those from PBT were terephthalic acid esters and benzoic acid esters.

---

Zusammenfassung Es wird ein kombiniertes System aus TG-DTA und FT-IR beschrieben. Mit dieser simultanen TG-DTA/FT-IR-Technik wurden spektroskopische und Massenverlustangaben über die thermische Zersetzung technisch wichtiger Polyester, namentlich von Poly(ethylenterephthalat) (PET) und Poly(Butylenterephthalat) (PBT) ermittelt. Die aus PET freigesetzten Gase waren Benzoesäure, Kohlendioxid und Kohlenmonoxid, die aus PBT freigesetzten Gase hingegen Terephthalsäureester und Benzoesäureester.

     

The performance of energy extrapolation procedures in truncated averaged coupled-pair functionals

Summary Energy extrapolation techniques in conjunction with individual configuration selection are applied to averaged coupled-pair functional expansions. In order to test the quality of this approach, benchmark calculations have been performed for N₂, the open and ring forms of O₃, and for the ground and several excited states of CuH and PdH. Reliable energy estimates are obtained for N₂ and the two transition metal hydrides and spectroscopic properties are in close agreement with the values for the non-truncated expansions. In the case of O₃ the perturbation corrections substantially underestimate the complete singles and doubles results. These deviations cancel to a large extent, however, in the calculated isomerization energy. The accuracy of the one-particle density matrix is examined by computing dipole moments for several electronic states of CuH and PdH. Deviations are significant in some cases. For the evaluation of properties the current approach requires modifications.Dedicated to Prof. W. Kutzelnigg on the occasion of his sixtieth birthday     

Assessment of a composite method based on selected density functional theory methods and complete basis set extrapolation formulas

Extrapolation formulas based on power and exponential formulas, as well as alternatives from a Taylor series, were tested and used with density functional theory (DFT) for the calculation of enthalpies of formation. The following four functionals were analyzed: B3LYP, BMK, M06-2X, and B2PLYP. Preliminary tests pointed to B2PLYP and B3LYP as the best and worst functionals, respectively. Taylor series expressions were as accurate as the power formulas and presented better performance than the exponential equation. The power formula (Equation (2)) and one of the simplest Taylor expressions (Equation (13)) were selected for the calculations with B3LYP and B2PLYP, with further empirical adjustments based on the higher level correction (HLC) and scaling of the experimental atomization energies used to calculate enthalpies of formation. HLC improved the B3LYP mean absolute error (MAE) from approximately 4.3 to 3.5 kcal mol⁻¹ using both extrapolation alternatives. For B2PLY, the MAEs were improved from 2.7 to 2.6 kcal mol⁻¹. Regarding the G3/05 test set, a significant improvement in the MAEs around 2.5 and 1.5 kcal mol⁻¹ were achieved using B3LYP and B2PLYP, respectively. The accuracy obtained from these empirical corrections was equivalent to other composite methods. The MAEs from B3LYP and B2PLYP may be suggested as ranges for the possible accuracy to be achieved by some DFT methods. The empirical corrections suggested in this work are improvements that may be considered to provide acceptable accuracy for enthalpies of formation and possibly other properties.     

FT-IR Study of Carbon Nanotube Supported Co-Mo Catalysts

In this paper, adsorption properties of dibenzothiophene (DBT) on carbon nanotube, carbonnanotube supported oxide state and sulfide state CoMo catalysts are studied by using thermal gravi-metric analysis (TGA) technique and FT-IR spectroscopy. Activated carbon support, 7-A1203 supportand supported CoMo catalysts are also subjected to studies for comparison. It was found that sulfidestate CoMoS/MWCNT, CoMoS/AC and CoMoS/γ-A12O3 catalysts adsorbed much more DBT moleculesthan their corresponding oxide state catalysts, as well as their corresponding supports. The chemicallyadsorbed DBT aromatic molecules did not undergo decomposition on the surface of supports, supportedoxide state CoMo catalysts and sulfide state CoMo catalysts when out-gassing at 373 K. FT-IR results indicated that DBT molecules mainly stand upright on the active sites (acid sites and/or transition active phases) of CoMoS/MWCNT catalyst. However, DBT aromatic molecules mainly lie flat on MWCNT and CoMoO/MWCNT.     

The quartz-cristobalite transformation in heated chert rock composed of micro and crypto-quartz by Micro-Raman and FT-IR spectroscopy methods

The quartz-cristobalite transformation in heated natural chert (flint) rock composed of micro- and ?ypto-quartz was investigated in the temperature interval of 1000–1300°C by micro-Raman spectroscopy, FT-IR spectroscopy, X-ray diffraction and Scanning Electron Microscopy. A small amount of crystobalite was first observed in the chert after heating at 1000°C for 1 h and the transformation was almost completed after heating at 1300°C for 24 h. On the other hand, cristobalite was not detected in well-crystallized pure quartz after heating under the same conditions. The transformation occurs as a solid state nucleation and crystal growth of cristobalite replacing quartz at high-temperatures. The chert rock is naturally rich in crystal defects and boundaries which serve as nucleation sites and enable an earlier quartz-cristobalite transformation.     

Applications of FT-IR/microscopy in forensic analysis

The technique of FT-IR/microscopy is applied to a variety of problems faced by the forensics chemist. These are as varied as the identification of drugs and fibers to the assignment of the origin of a paint sample. Our efforts in the effective utilization of FT-IR/microscopy in this area and usage of new data bases to aid in identifications are discussed.     

Accuracy of energy extrapolation in multireference configuration interaction calculations

The accuracy of extrapolation procedures in conjunction with energy-based configuration selection in CI calculations is examined. The normally high accuracy of such extrapolation can deteriorate in multireference CI calculations when configuration functions of low weight are included in the root (reference) set. This is due to the inadequacy of second-order energy contribution estimates for the very large number of discarded low-contribution functions generated as single and double excitations from the minor members of the root set. The problem may be overcome by increasing the number of configurations included in the zero-order function used for the energy contribution estimation process. Illustrative results are presented for excited states of the H₂O molecule and the H₂O⁺ ion.     

Surface oxidation of high-surface-area silicon carbide: FT-IR studies

The surface of ultrafine silicon carbide powders, prepared by a laser-driven gas-phase reaction was studied as a self-supporting disk by FT infrared spectrometry. After evacuation silicon and carbon atoms located at the surface give rise tovSiH andvCH bands. When heating in oxygen, subtraction spectra showed features which could be strictly correlated with a progressive growth of a silica layer: SiH and CH bands were replaced by new bands characteristic of amorphous silica and the typical band of surface silanol groups on silica (3745 cm^–1) simultaneously increased.     

On-line sample treatment and FT-IR determination of doxylamine succinate in pharmaceuticals

A low solvent consumption method for Fourier transform infrared spectroscopy (FT-IR) determination of doxylamine succinate in pharmaceuticals has been developed. The analyte was continuous and selectively extracted with a 13% (v/v) ethanol:chloroform solvent mixture, recirculating the solvent through the sample and monitoring the process by FT-IR. Doxylamine succinate was determined by on-line standard addition measuring the peak area in the regions 1730–1710 and 1485–1462 cm⁻¹ corrected with a two-point baseline established between 2000 and 1800 cm⁻¹. This new method implies low volumes of chloroformic solvent mixture, only 2.6 mL per sample, in front of classical batch FT-IR methods, improving analytical efficiency and reducing waste generation. The on-line extraction and standard addition determination of doxylamine succinate allowed a throughput of 10 h⁻¹.     

The differentiation and identification of pathogenic bacteria using FT-IR and multivariate statistical analysis

Correspondence analysis was used to classify the pattern-like FT-IR spectra of intact bacteria. The analysis was performed on a data set of approximately 80 normalized spectral derivatives of a selection of pathogenic bacteria. The correspondence analysis proved that the various different bacterial species were clustering in distinct regions of the correspondence maps suggesting that there do exist correlations between spectral data and biochemical/microbiological classification.     

聚乙烯尼龙共混物的PGC-MS和FT-IR联用鉴别

采用裂解气相色谱-质谱法和红外光谱法研究聚乙烯和尼龙共混物的组成;据此建立鉴别聚乙烯共混物组分的方法;红外光谱法可以准确鉴别出尼龙组分,裂解气相色谱-质谱法可以准确鉴别出聚乙烯组分以及尼龙的具体结构;二种方法结合使用,可以准确鉴别聚乙烯和尼龙共混物的组分。