Ag纳米粒子修饰光纤探针在等离激元催化反应中的应用

本文发展了一种基于Ag纳米粒子(AgNPs)修饰的局域表面等离激元共振(LSPR)光纤探针,作为等离激元催化反应基底同时原位检测表面增强拉曼光谱(SERS)信号,实现反应与检测一体化。本文使用(3-氨基丙基)三甲氧基硅烷(APTMS)分子将AgNPs组装到光纤探针表面。通过调控自组装时间,可形成AgNPs均匀分布的探针。以对巯基苯胺(PATP)作为反应的模型分子,获得了较好的等离激元催化及信号检测效果。在相同光源条件下,从光纤内部激发收集所得产物的SERS信号强度为外部激发收集的12.8倍,表明内激发收集方式在反应及信号检测方面具有优势;在一定浓度范围(10~(-4)–10~(-8)mol·L~(-1))内可用该光纤探针对PATP溶液进行定量分析;运用该光纤探针开展了等离激元催化PATP分子偶联反应的原位动力学研究。该LSPR光纤探针具有较高灵敏度,对样品损伤小,可在多场合下实现原位检测,且制备简便、成本较低。还有望结合近场扫描光学显微技术进一步对样品表面进行微区等离激元催化反应及检测并得到反应的二维分布图。     

Competitive surface-enhanced Raman scattering effects in noble metal nanoparticle-decorated graphene sheets

Herein, noble metal nanoparticle (Au or Ag NP) decorated graphene sheets, fabricated according to a facile one-pot environmentally friendly method, are used as good substrates for the investigation of the combined surface-enhanced Raman scattering (SERS) effect, where both the electromagnetic mechanism and the chemical mechanism effects coexist among the Au or Ag NPs, graphene sheets and the absorbed analytes. Our results show that, in aqueous solution, the SERS effect of both the Au and Ag NPs on the absorbed probe molecules and on graphene is competitive, which varies dependent on the species and the concentration of the absorbed probe molecule. By a detailed comparison of three probe molecules (rhodamine 6G, nile blue A, and 4-aminobenzenethiol) with different coupling abilities to the graphene sheets, we finally attribute this phenomenon to the result of the strong suppressing effect of the macrocyclic probe molecules on the SERS of graphene, induced by charge transfer, as the probe molecules are coupled to the graphene sheets. This competitive effect is a non-ignorable phenomenon when graphene/Au or Ag nanocomposites are used as SERS substrates, and our study may deepen our understanding of the SERS mechanism.     

复合SERS基底的构建及性质

通过自组装方法以对巯基苯胺(PATP)为偶联分子, 在石英基片上构筑了多种形貌的银钠米粒子单层结构和三明治结构. 研究了组装膜在不同激发线下表面增强拉曼散射(SERS)的增强差异. 研究结果表明, 单层基底和三明治基底中偶联分子的SERS信号因银纳米粒子间的电磁场耦合而显著增强, 且在三明治结构中增强更加明显. 对复合SERS基底增强因子进行计算可知, 复合SERS基底的表面等离子体共振(SPR)峰与激发线的匹配程度越好, 其增强因子越大. 在三明治结构中更易发生PATP分子转变为对巯基偶氮苯(DMAB)分子的激光诱导催化偶联反应. 另外, 该激光诱导催化偶联反应与激发波长密切相关.     

Gas-Phase Deposited Plasmonic Nanoparticles Supported on 3D-Graphene/Nickel Foam for Highly SERS Detection

In this work, we proposed a novel three-dimensional (3D) plasmonic nanostructure based on porous graphene/nickel foam (GNF) and gas-phase deposited Ag nanoparticles (NPs).Ag NPs with high density were directly deposited on the surface of 3D GNF by performing a novel cluster beam deposition approach. In comparison with traditional Ag substrate(SiO₂/Ag), such hot-spots enriched 3D nanostructure showed extremely high electromag-netic field enhancement under incident light irradiation which could be used as a sensitive chemical sensor based on surface enhanced Raman scattering (SERS). The experimental results demonstrated that the proposed nanostructure showed superior SERS performance in terms of Raman signal reproducibility and sensitivity for the probe molecules. 3D full-wave simulation showed that the enhanced SERS performance in this 3D hierarchical plasmonic nanostructure was mainly obtained from the hot-spots between Ag NPs and the near-field coupling between Ag NPs and GNF sca olds. This work can provide a novel assembled SERS substrate as a SERS-based chemical sensor in practical applications.     

模板法合成金银核壳纳米线及电化学表征

采用氧化铝模板由交流电沉积制备纯银纳米线.然后借助化学还原法,在已制备好的银线表面包裹不同厚度的金壳层,得到具有核壳结构的AgcoreAushell复合纳米线.电子显微镜(SEM,TEM)显示该复合结构纳米线表面形貌与加入的金盐量有关,而且包裹层较薄的复合纳米线表面存在大量的孔洞.循环伏安测试表明,具有孔洞效应的复合纳米线经多次循环扫描后即可过渡到无孔洞效应的表面.以对巯基苯胺(PATP)作为探针分子的表面增强拉曼光谱,可用于表征纳米材料的表面结构.     

Size-controlled deposition of Ag nanoparticles on alumina with the assistance of a photo-induced chromic reaction, and study of their catalytic properties

This paper describes a promising method to synthesize supported metal catalysts based on a photochromic reaction. Highly dispersed Ag nanoparticles (NPs) with a mean diameter of ca. 10 nm stabilized by 3-mercaptopropionic acid (3-MPA) were prepared as a colloidal precursor solution. The zeta electric potential was found to be negatively charged in the region of pH higher than 5 due to the presence of dissociated carboxylate ions (-COO(-)), which led to electric repulsion between Ag NPs and kept the solution in a highly dispersed colloidal state. In the presence of photochromic molecules, trans-2-hydroxychalcone, the photo-irradiation gradually decreased the electric charge on the nanoparticles owing to the formation of flavylium cations, which induced the assembly of Ag NPs. Such photo-induced assembly-dispersion control of Ag NPs enables size selective deposition on a catalyst support, which is controlled by varying the photo-irradiation time.     

Pt3Te4 nanoparticles from tellurium nanowires

We report the synthesis of platinum telluride nanoparticles (Pt(3)Te(4) NPs) in the solution phase at room temperature using a template-assisted method. The dendrimeric aggregates formed are composed of several small units of Pt(3)Te(4) NPs of ～4 nm diameter. Tellurium nanowires (Te NWs) are used as the template and the reducing agent in the growth of NPs which occurs due to the galvanic replacement reaction between Te NWs and PtCl(6)(2-). Surface-enhanced Raman scattering (SERS) of the dispersed Pt(3)Te(4) NPs was studied using crystal violet (CV) as the analyte. SERS sensitivity up to 10(-8) M of CV was observed. The Raman enhancement factor (EF) of adsorbed CV on NP aggregates was calculated to be 1.74 × 10(5). The catalytic ability of the as-synthesized Pt(3)Te(4) NPs for the reduction of 4-nitrophenol (4-NP) was studied.     

Liquid-phase oxidation of toluene to benzaldehyde with molecular oxygen catalyzed by copper nanoparticles supported on graphene

Highly-dispersed copper nanoparticles (Cu NPs) were fabricated on the surface of reduced graphene oxide via direct hydrazine hydrate reduction of Cu²⁺ in aqueous solution. Scanning electron microscope and transmission electron microscope images show that the Cu NPs are distributed on the surface of graphene nanosheets, and the average particle size was about 40 nm. The Cu NPs supported on graphene have high reaction activity for the oxidation of toluene to corresponding benzaldehyde. It was found that the selectivity reached 66.5% and the conversion of toluene reached 11.5%.     

Cuprous oxide nanoparticles dispersed on reduced graphene oxide as an efficient electrocatalyst for oxygen reduction reaction

Cuprous oxide (Cu(2)O) nanoparticles dispersed on reduced graphene oxide (RGO) were prepared by reducing copper acetate supported on graphite oxide using diethylene glycol as both solvent and reducing agent. The Cu(2)O/RGO composite exhibits excellent catalytic activity and remarkable tolerance to methanol and CO in the oxygen reduction reaction.     

Silver Nanostructures on Graphene Oxide as the Substrate for Surface-Enhanced Raman Scattering (SERS)

Nanosized surface-enhanced Raman scattering (SERS) substrates fabricated by the controlled growth of metal nanostructures on water-dispersed two-dimensional nanomaterials can open a new avenue for SERS analysis of liquid samples in biological fields. In this work, regular and uniform Ag nanostructures were grown on the surface of graphene oxide (GO) through a microwave-assisted hydrothermal method. Polyamidoamine (PAMAM) dendrimers were assembled on the surface of GO to form GO/PAMAM templates for growing Ag nanostructures, which are primarily comprised of Ag dimers and trimers. The prepared Ag/GO nanocomposites are highly dispersed and stable in aqueous solution and may be used as substrates for enhanced Raman detection of rhodamine 6?G (R6G) in aqueous solution. This special substrate provides high-performance SERS and suppresses R6G fluorescence in aqueous solution and is promising as a nanosized material for the enhanced Raman detection of liquid samples in biological diagnostics.     

Microfluidic Synthesis Enables Dense and Uniform Loading of Surfactant‐Free PtSn Nanocrystals on Carbon Supports for Enhanced Ethanol Oxidation

Developing new synthetic methods for carbon supported catalysts with improved performance is of fundamental importance in advancing proton exchange membrane fuel cell (PEMFC) technology. Continuous‐flow, microfluidic reactions in capillary tube reactors are described, which are capable of synthesizing surfactant‐free, ultrafine PtSn alloyed nanoparticles (NPs) on various carbon supports (for example, commercial carbon black particles, carbon nanotubes, and graphene sheets). The PtSn NPs are highly crystalline with sizes smaller than 2 nm, and they are highly dispersed on the carbon supports with high loadings up to 33 wt %. These characteristics make the as‐synthesized carbon‐supported PtSn NPs more efficient than state of the art commercial Pt/C catalysts applied to the ethanol oxidation reaction (EOR). Significantly enhanced mass catalytic activity (two‐times that of Pt/C) and improved stability are obtained.     

Differential SERS activity of gold and silver nanostructures enabled by adsorbed poly(vinylpyrrolidone)

We report that poly(vinylpyrrolidone) (PVP), a common stabilizer of colloidal dispersions of noble metal nanostructures, has a dramatic effect on their surface-enhanced Raman scattering (SERS) activity and enables highly selective SERS detection of analytes of various type and charge. Nanostructures studied include PVP-stabilized Au-Ag nanoshells synthesized by galvanic exchange reaction of citrate-reduced Ag nanoparticles (NPs), as well as solid citrate-reduced Ag and Au NPs, both before and after stabilization with PVP. All nanostructures were characterized in terms of their size, surface plasmon resonance wavelength, surface charge, and chemical composition. While the SERS activities of the parent citrate-reduced Ag and Au NPs are similar for rhodamine 6G (R6G) and 1,2-bis(4-pyridyl)ethylene (BPE) at various pH values, PVP-stabilized nanostructures demonstrate large differences in SERS enhancement factors (EFs) between these analytes depending on their chemical nature and protonation state. At pH values higher than BPE's pK(a2) of 5.65, where the analyte is largely unprotonated, the PVP-coated Au-Ag nanoshells showed a high SERS EF of >10(8). In contrast, SERS EFs were 10(3)- to 10(5)-fold lower for the protonated form of BPE at lower pH values, or for the usually highly SERS-active cationic R6G. The differential SERS activity of PVP-stabilized nanostructures is a result of discriminatory binding of analytes within-adsorbed PVP monolayer and a subsequent increase of analyte concentration at the nanostructure surface. Our experimental and theoretical quantum chemical calculations show that BPE binding with PVP-stabilized Au-Ag nanoshells is stronger when the analyte is in its unprotonated form as compared to its cationic, protonated form at a lower pH.     

银/金纳米线阵列表面增强拉曼基底的制备及对孔雀石绿的高灵敏度检测

利用种子介导的软模板生长方法制备了金纳米线(Au NWs)阵列, 通过调节生长温度控制Au NWs阵列的形貌, 最后在经硼氢化钠(NaBH₄)清洗过的Au NWs阵列上化学沉积银纳米颗粒(Ag NPs), 制得银/金纳米线(Ag/Au NWs)阵列作为表面增强拉曼散射(SERS)基底. 选用罗丹明6G(R6G)作为拉曼探针分子测定了Ag/Au NWs阵列的SERS性能. 结果表明, Ag/Au NWs阵列作为SERS基底具有高灵敏度、 优异的信号均匀性和良好的稳定性. 使用Ag/Au NWs阵列对孔雀石绿(MG)检测的检出限可低至1×10^-8 mol/L, 线性范围为 1×10^-8~1×10^-4 mol/L. NaBH₄可以在不影响SERS性能的情况下去除Ag/Au NWs阵列上吸附的分子, 使得 SERS基底可以重复使用. 使用Ag/Au NWs阵列对湖水中的MG进行检测, 得到了可靠的回收率, 证明Ag/Au NWs 阵列在检测环境水体中的孔雀石绿上具有应用潜力.     

Interactions between Keggin-Type Lacunary Polyoxometalates and Ag Nanoparticles: A Surface-Enhanced Raman Scattering Spectroscopic Investigation

Interactions between two Keggin-type lacunary polyoxometalates (POMs), PW₁₁O and SiW₁₁O, and pre-formed citrate-protected colloidal Ag nanoparticles (NPs) were studied by surface-enhanced Raman scattering (SERS) and UV-Vis spectroscopies. Clear SERS evidence of displacing the originally surface-bound citrate ions by the subsequently added POMs indicates a stronger metal–ligand interaction between the POMs and the Ag NPs. Accompanied red-shifts in the surface plasma peak position of the Ag NPs were also observed for both POMs. The simultaneous presence of a number of SERS vibrational bands which can be assigned to vibrational modes of the POM molecule suggests that its overall structure is intact upon adsorption. Based on the SERS observations, a bonding between the penta-dentate aperture of the POMs and the Ag NP surface was proposed.Dedicated to the retirement of Michael Pope.     

Silver overlayer-modified surface-enhanced Raman scattering-active gold substrates for potential applications in trace detection of biochemical species

Because Ag and Au nanoparticles (NPs) possess well-defined localized surface plasmon resonance (LSPR) they are popularly employed in the studies of surface-enhanced Raman scattering (SERS). As shown in the literature and in our previous studies, the advantage of SERS-active Ag NPs is their higher SERS enhancement over Au NPs. On the other hand, the disadvantage of SERS-active Ag NPs compared to Au NPs is their serious decay of SERS enhancement in ambient laboratory air. In this work, we develop a new strategy for preparing highly SERS-active Ag NPs deposited on a roughened Au substrate. This strategy is derived from the modification of electrochemical underpotential deposition (UPD) of metals. The coverage of Ag NPs on the roughened Au substrate can be as high as 0.95. Experimental results indicate that the SERS of Rhodamine 6G (R6G) observed on this developed substrate exhibits a higher intensity by ca. 50-fold of magnitude, as compared with that of R6G observed on the substrate without the deposition of Ag NPs. The limit of detection (LOD) for R6G measured on this substrate is markedly reduced to 2 × 10⁻¹⁵ M. Moreover, aging of SERS effect observed on this developed substrate is significantly depressed, as compared with that observed on a generally prepared SERS-active Ag substrate. These aging tests were performed in an atmosphere of 50% relative humidity (RH) and 20% (v/v) O₂ at 30 °C for 60 day. Also, the developed SERS-active substrate enables it practically applicable in the trace detection of monosodium urate (MSU)-containing solution in gouty arthritis without a further purification process.     

Theoretical Design and Experimental Realization of Quasi Single Electron Enhancement in Plasmonic Catalysis

By a combination of theoretical and experimental design, we probed the effect of a quasi‐single electron on the surface plasmon resonance (SPR)‐mediated catalytic activities of Ag nanoparticles. Specifically, we started by theoretically investigating how the E‐field distribution around the surface of a Ag nanosphere was influenced by static electric field induced by one, two, or three extra fixed electrons embedded in graphene oxide (GO) next to the Ag nanosphere. We found that the presence of the extra electron(s) changed the E‐field distributions and led to higher electric field intensities. Then, we experimentally observed that a quasi‐single electron trapped at the interface between GO and Ag NPs in Ag NPs supported on graphene oxide (GO‐Ag NPs) led to higher catalytic activities as compared to Ag and GO‐Ag NPs without electrons trapped at the interface, representing the first observation of catalytic enhancement promoted by a quasi‐single electron.     

Fabrication of bimetallic microfluidic surface-enhanced Raman scattering sensors on paper by screen printing

Au–Ag bimetallic microfluidic, dumbbell-shaped, surface enhanced Raman scattering (SERS) sensors were fabricated on cellulose paper by screen printing. These printed sensors rely on a sample droplet injection zone, and a SERS detection zone at either end of the dumbbell motif, fabricated by printing silver nanoparticles (Ag NPs) and gold nanoparticles (Au NPs) successively with microscale precision. The microfluidic channel was patterned using an insulating ink to connect these two zones and form a hydrophobic circuit. Owing to capillary action of paper in the millimeter-sized channels, the sensor could enable self-filtering of fluids to remove suspended particles within wastewater without pumping. This sensor also allows sensitive SERS detection, due to advantageous combination of the strong surface enhancement of Ag NPs and excellent chemical stability of Au NPs. The SERS performance of the sensors was investigated by employing the probe rhodamine 6G, a limit of detection (LOD) of 1.1 × 10⁻¹³ M and an enhancement factor of 8.6 × 10⁶ could be achieved. Moreover, the dumbbell-shaped bimetallic sensors exhibited good stability with SERS performance being maintained over 14 weeks in air, and high reproducibility with less than 15% variation in spot-to-spot SERS intensity. Using these dumbbell-shaped bimetallic sensors, substituted aromatic pollutants in wastewater samples could be quantitatively analyzed, which demonstrated their excellent capability for rapid trace pollutant detection in wastewater samples in the field without pre-separation.     

Coating sulfonated polystyrene microspheres with highly dense gold nanoparticle shell for SERS application

The fabrication of highly dense gold nanoparticles (NPs)-coated sulfonated polystyrene (PS) microspheres and their application in surface-enhanced Raman spectroscopy (SERS) were reported. After the preparation of PS microsphere using dispersion polymerization and subsequent sulfonation, [Ag(NH₃)₂]⁺ ions were adsorbed on the surfaces of the sulfonated PS microspheres and then reduced to silver nanoseeds for further growth of gold NPs shell by seeded growth approach. Reaction conditions such as the concentration of the growth solution and growth time were adjusted to achieve nonspherical gold NPs-coated PS microspheres with different coverage degree. The application of the as-prepared spiky gold NPs-coated PS microsphere hybrid composite in SERS was finally investigated by using 4-aminothiophenol as probe molecules. The results showed that as-prepared gold NPs-coated PS microspheres could be used as functional hybrid materials to exhibit excellent enhancement ability in SERS.

Surface enhanced Raman scattering of p-aminothiophenol self-assembled monolayers in sandwich structure fabricated on glass

A sandwich structure consisting of Ag nanoparticles (NPs), p-aminothiophenol (p-ATP) self-assembled monolayers (SAMs), and Ag NPs was fabricated on glass and characterized by surface enhanced Raman scattering (SERS). The SERS spectrum of a p-ATP SAM in such sandwich structure shows that the electromagnetic enhancement is greater than that on Ag NPs assembled on glass. The obtained enhancement factors (EF) on solely one sandwich structure were as large as 6.0 +/- 0.62 x 10(4) and 1.2 +/- 0.62 x 10(7) for the 7a and 3b(b(2)) vibration modes, respectively. The large enhancement effect of p-ATP SAMs is likely a result of plasmon coupling between the two layers of Ag NP (localized surface plasmon) resonance, creating a large localized electromagnetic field at their interface, where p-ATP resides. Moreover, the fact that large EF values (approximately 1.9 +/- 0.7 x 10(4) and 9.4 +/- 0.7 x 10(6) for the 7a- and b(2)-type vibration modes, respectively) were also obtained on a single sandwich structure of Au NPsp-ATP SAMsAg NPs in the visible demonstrates that the electromagnetic coupling does not exist only between Ag NPs but also between Au and Ag NPs. The lower EF values on Au-to-Ag NPs compared to those on Ag-to-Ag NPs demonstrate that the Au-to-Ag coupling must be less effective than the Ag-to-Ag coupling for the induction of SERS in the visible.     

Adsorbed state of p-mercaptobenzoic acid on silver nanoparticles

To exploit a gap mode plasmon in flocculates of metal nanoparticles most efficiently, the interaction between adsorbed chemical species and metal nanostructures were adjusted. We successfully formed flocculates of Ag nanoparticles (AgNPs) using electrostatic interaction between dissociated p-mercaptobenzoic acid (PMBA), protonated p-aminothiophenol (PATP) and their counter ions (Mⁿ⁺, X^m−), as well as van der Waals force between neutral PMBA, PATP and AgNPs. Detailed adsorbed state of PMBA and PATP in addition to trapped counter ions was characterized using enormous SERS enhancement in a flocculation method.