Fabrication of polymer Langmuir-Blodgett films containing regioregular poly(3-hexylthiophene) for application to field-effect transistor

Semiconducting thin films consisting of regioregular poly(3-hexylthiophene) (RR-PHT) and poly(N-dodecylacrylamide) (pDDA) were constructed by the Langmuir-Blodgett (LB) technique. A mixture of RR-PHT and pDDA spread from a chloroform solution on a water surface forms a stable monolayer, which can be transferred onto solid substrates by the LB method, yielding a well-defined polymer LB film. Surface morphology studies of the LB film indicate that the RR-PHT is dispersed uniformly throughout the surface. The polymer thin film was chemically doped by contacting with FeCl3 acetonitrile solution, and a conductivity of 5.6 S/cm was achieved. Further, the LB film was utilized as the semiconducting film in the field-effect transistor (FET), and mobilities of 2.2 x 10(-4) and 4.4 x 10(-4) cm2 V(-1) s(-1) were obtained by analyzing the saturated and linear regions of the current-voltage characteristic, respectively.     

Preparation and characterization of electrically conducting Langmuir-Blodgett films of poly(N-octadecylaniline)

A stable monolayer of N-octadecylaniline containing stearic acid at the air-water interface has been obtained. However, the Langmuir monolayer of pure poly(N-octadecylaniline) was not stable, but mixed Langmuir-Blodgett films of this polymer with stearic acid in different ratios as a spreading aid were stable. The electrical conductivity of these films increased by five orders of magnitude after doping with iodine as compared to that before iodine doping (5.8x10(-7) S cm(-1)). Temperature-dependent electrical conductivity suggested that these films were semiconducting in nature with low thermal activation energy. Impedance analyses of these films revealed that the equivalent circuit for poly(N-octadecylaniline) was (RQ) whereas that for mixed poly(N-octadecylaniline) with stearic acid was (RQ)(RQ).     

Structures of palmitoyl-L and DL-lysine monolayers at the air-water interface--polarization modulation infrared reflection absorption spectroscopic study

Polarization modulation infrared reflection absorption spectroscopy (PM-IRAS) was applied to measure the IR spectra of palmitoyl-DL-lysine (L-PL) and palmitoyl-DL-lysine (DL-PL) at the air-water interface. The spectra in the amide I and II regions were simulated by using the extinction coefficients of the amide I and II bands of L-PL and DL-PL determined by the analyses of the IR external reflection spectra of the Langmuir-Blodget (LB) films prepared on a Ge plate (Yasukawa et al. J. Mol. Struct. 2005, 735-736, 53), indicating the angle between the plane of the secondary amide group (the amide plane) and the surface normal in the L-PL monolayer to be about 20 degrees and the angle in the DL-PL monolayer to be about 37 degrees. Comparison of the tilt angles with the corresponding angles in the LB films (about 20 degrees for the LB film of L-PL; about 49 degrees for the LB film of DL-PL) indicated that, upon being transferred to the solid substrate from the air-water interface, the L-PL monolayer keeps the orientation of the amide plane virtually unchanged, while the DL-PL monolayer changes the orientation appreciably to a horizontal direction. The orientation change of the amide plane was interpreted as due to the accommodation of irregularly oriented palmitoyl groups into the LB films of DL-PL on the solid substrate.     

Effect of water and air-water interface on the structural modification of Ni-arachidate Langmuir-Blodgett films

Nickel arachidate (NiA) Langmuir-Blodgett (LB) films have been deposited on hydrophilic Si(0 0 1) substrates by three (up-down-up) and five (up-down-up-down-up) strokes. During deposition, substrates were kept inside the water subphase for different times after each down stroke. Structural information of all the LB films have been obtained from X-ray reflectivity (XRR) studies. One and two symmetric monolayer (SML) was deposited on top of the asymmetric monolayer (AML) in three and five stokes respectively. All the preformed LB films were then used to go through the air-water interface with the same speed that was used at the time of film deposition. Structural information obtained from the XRR studies show that mainly the top layer density decreases after passing through the air-water interface but the layered structure remains the same. Information obtained from both the XRR and atomic force microscopy (AFM) studies suggest that molecules peeled from the top SML layer do not reincorporate with the LB film through tail-tail hydrophobic interaction. Our study shows that NiA LB film has better stability compared with cadmium arachidate LB film inside the water subphase without forming any out-of-plane molecular reorganization.     

荧光素衍生物LB膜对TiO2电极的光敏化作用

合成了三种荧光素长碳链衍生物，通过LB技术将它们组装成单分子薄膜，修饰在用溶胶-凝胶法制备的TiO2透明电极上，研究了这些LB膜的结构和特性及它对TiO2的光增感作用．并对其光敏化机理作了阐述．     

Polymer-surfactant layered heterostructures by electropolymerization of phenosafranine in Langmuir-Blodgett films

Langmuir-Blodgett (LB) films of the water-soluble dye phenosafranine (PS) have been prepared by its adsorption from aqueous dye solution to an arachidic acid (AA) monolayer at the air-water interface. Atomic force microscopy (AFM) images of the LB films revealed the effect of change in pH of deposition on the degree of complexation of AA with the PS dye. Well-defined circular islands and holes were observed which disappeared with the increase in pH. Polarized absorption studies indicated that the dye molecules are oriented uniaxially with their long axis titled at a constant angle to the surface normal of the LB film. Within the restricted geometry of the LB film, the PS dye was electropolymerized to form a two-dimensional film of poly(phenosafranine) sandwiched between arachidic acid layers. The film was characterized by IR spectroscopy, cyclic voltammetry, and AFM. X-ray diffraction studies reveal the presence of a layer structure in the AA-PS LB film before and after polymerization. The polymer film showed highly anisotropic electrical conductivity of ca. 10 orders of magnitude. This indicates the formation of two-dimensional polyPS layers between arachidic acid layers resulting in a layered heterostructure film having alternate conducting and insulating regions. Also, the conductivity of the polyPS prepared from LB film was found to be approximately 2.5 times higher than the conductivity of polyPS prepared by solution polymerization method.     

Manipulation of Multicomponent Langmuir-Blodgett Films of Electrically Conductive Polymers: Polypyrrole and Poly(3-Hexylthiophene)

Abstract

Multicomponent Langmuir-Blodgett (LB) films containing poly-pyrrole, 3-octadecanoyl pyrrole, and poly(3-hexylthiophene) were fabricated via a novel in-situ polymerization process. In this process, pyrrole monomer is polymerized at the air-subphase interface in the presence of poly(3-hexylthiophene) by using a subphase containing 1 wt% FeCl₃. The resultant electrically conductive films could be readily deposited onto solid substrates as Z-type films by the vertical lifting method. By using visible absorption, x-ray diffraction, and FTIR measurements, it was found that all three components were present within the transferred films, with the polypyrrole chains assuming a preferential orientation parallel to the film surface. The conductivities of the mixed LB films were as high as 1.0 S/cm, and the stability of the conductivity was very good. Chemical doping of poly(3-hexylthiophene) within the film with strong oxidizing agents such as I₂ further enhanced the conductivity of the film.     

Structural control in thin layers of poly(p-phenyleneethynylene)s: photophysical studies of Langmuir and Langmuir-Blodgett films

We present the relationship between the spatial arrangement and the photophysical properties of fluorescent polymers in thin films with controlled structures. Eight surfactant poly(p-phenyleneethynylene)s were designed and studied. These detailed studies of the behavior of the polymers at the air-water interface, and of the photophysical properties of their transferred LB films, revealed key structure-property relationships. Some of the polymers displayed pi-aggregates that are characteristic of an edge-on structure at the air-water interface. Monolayer LB films of these polymers showed greatly reduced quantum yields relative to solution values. Other polymers exhibited a highly emissive face-on structure at the air-water interface, and did not form pi-aggregates. The combination of pressure-area isotherms and the surface pressure dependent in situ UV-vis spectra of the polymers at the air-water interface revealed different behavioral details. In addition, the UV-vis spectra, fluorescence spectra, and quantum yields of the LB films provide design principles for making highly emissive films.     

Spectroscopic Studies on LB Film of a Liquid Crystalline Polymaleic Acid Polymer(Ⅰ)

The stable monolayer from the preformed amphiphilic liquid crystalline polymer (PMPE) can be obtained on the air-water interface, the monolayer can be transferred onto solid substrates in Y-type film. The spectroscopic characteristics are investigated using UV-Vis and Fourier transform infrared (FT-IR) spectra. Polarized UV-Vis and FTIR spectra show that the LB film assembly is packed in an ordering way.     

Adsorption kinetics of a fluorescent dye in a long chain fatty acid matrix

This work reports the adsorption kinetics of a highly fluorescent laser dye rhodamine B (RhB) in a preformed stearic acid (SA) Langmuir monolayer. The reaction kinetics was studied by surface pressure-time (π-t) curve at constant area and in situ fluorescence imaging microscopy (FIM). Increase in surface pressure (at constant area) with time as well as increase in surface coverage of monolayer film at air-water interface provide direct evidence for the interaction. ATR-FTIR spectra also supported the interaction and consequent complexation in the complex films. UV-vis absorption and Fluorescence spectra of the complex Langmuir-Blodgett (LB) films confirm the presence of RhB molecules in the complex films transferred onto solid substrates. The outcome of this work clearly shows successful incorporation of RhB molecules into SA matrix without changing the photophysical characteristics of the dye, thus making the dye material as LB compatible.     

Fabrication of densely packed titania nanosheet films on solid surface by use of Langmuir-Blodgett deposition method without amphiphilic additives

Densely packed exfoliated nanosheet films such as Ti0.91O2, Ti0.8M0.2O2 (M = Co, Ni), Ti0.6Fe0.4O2, and Ca2Nb3O10 on solid substrates were prepared by the LB transfer method without any amphiphilic additives at the air-water interface. Nanosheet crystallites covered nearly 95% on the solid surface with minimum overlapping of nanosheets. The LB transfer method of the Ti0.91O2 nanosheet monolayer film is applicable for not only hydrophilic substrates such as quartz, silicon, indium-tin oxide (ITO), and glass but also the hydrophobic Au surface. On the basis of these points, the LB transfer method has advantages compared to the alternating layer-by-layer method, which makes use of oppositely charged polyelectrolytes such as poly(ethylenimine) (PEI). Adsorption of hydrophobic Ti0.91O2 nanosheets at the air-water interface is responsible for this LB transfer deposition method. The addition of tetrabutylammonium bromide into the subphase assisted the adsorption, causing an increase in the adsorbed amount of Ti0.91O2 nanosheets at the air-water interface.     

Raman spectroscopic investigation of the single-monolayer Langmuir-Blodgett film of C16NaphOH and C10AzoNaphC4N-SDS

Raman spectra were measured for Langmuir-Blodgett (LB) films of C(16)NaphOH and C(10)AzoNaphC(4)N-SDS on Calcium Fluorite substrate for the first time. In order to find out favorable excitation condition, Raman spectra of the single and multi-monolayer LB films excited at different lines at 244, 514, 633 and 778 nm are recorded and compared in the present study. Raman spectrum of the monolayer LB film of C(16)NaphOH excited by 244 nm demonstrate that excellent signal to noise is achieved even for one monolayer LB film with an extremely short integrating time as 60 s because of being resonantly enhanced, while no meaningful spectra were recorded under the same condition for the monolayer LB film of C(10)AzoNaphC(4)N-SDS because of burning. Using a HeNe 633 nm excitation the problem with strong substrate fluorescence was partially solved, since under these conditions this fluorescence is mainly outside the fingerprint region of the LB film molecules (1000-2000 cm(-1)). Therefore by using the HeNe laser excitation, Raman spectra with high signal to noise ratio of LB films of C(16)NaphOH were collected and shown in this paper. These findings stress again the necessity to define an appropriate Raman system for this special application of LB film diagnosis.     

Molecular recognition of cytosine- and guanine-functionalized nucleolipids in the mixed monolayers at the air-water interface and Langmuir-Blodgett films

Molecular recognition of mixed nucleolipids of 1-(2-octadecyloxycarbonylethyl)cytosine and 7-(2-octadecyloxycarbonylethyl)guanine in the monolayers at the air-water interface and Langmuir-Blodgett (LB) films has been investigated in detail using surface pressure/potential-area isotherms, infrared reflection-absorption spectroscopy (IRRAS), and Fourier transform infrared (FTIR) transmission spectroscopy, respectively. Prior to molecular recognition, the cytosine moieties in the monolayer were hydrogen bonded with an almost flat-on orientation, the alkyl chains were uniaxially oriented with respect to the film normal, the guanine moieties in the monolayer were stacked probably through pi-pi interaction with an end-on orientation, and the C-C-C planes of the alkyl chains were preferentially oriented parallel to the water surface. In the monolayer of equimolar mixture, molecular recognition between the cytosine and guanine moieties occurred together with the ring planes of base pairing and the C-C-C planes of the alkyl chains favorably oriented parallel to the water surface. The guanine moieties underwent an orientation change from an end-on mode before molecular recognition to a flat-on one after molecular recognition. The base pairing between the cytosine and guanine moieties in the monolayers was achieved since the N7-substituted guanine derivatives suppressed the formation of guanine tetramers. Both the IRRAS spectra of the monolayers and the FTIR spectra of the LB films presented the exact sites in the cytosine and guanine moieties for the formation of triple hydrogen bonds. The base pairing resulted in a change in molecular orientation and interaction, and the corresponding LB film exhibited a different phase transition behavior from a typical crystal transition for the cytosine-functionalized nucleolipids and an analogous glass transition for the guanine-functionalized nucleolipids. The thermal stability of the mixed LB film was improved in comparison to the LB films of pure components.     

Luminescent Langmuir-Blodgett films of platinum(II) complex [Pt(L18)Cl](PF6) (L18 = 2,6-bis(1-octadecylbenzimidazol-2-yl)pyridine)

A novel amphiphilic Pt complex containing 2,6-bis(1-octadecylbenzimidazol-2-yl)pyridine (L18), [Pt(L18)Cl](PF6), has been synthesized. The complex exhibits concentration-dependent absorption and emission spectra in solution. With increasing the concentration of the Pt complex, we observed a new absorption band centered at 550 nm derived from a metal-metal d sigma* to ligand pi* charge transfer (MMLCT) transition and the corresponding broad emission centered at 650 nm. The Pt complex is surface-active, and the surface pressure-area isotherm reveals three phase transitions. The three phases correspond to one liquid-expanding phase and two solid-condensed phases, respectively, with different intermolecular overlap in the "flat-on" orientation at the air-water interface. Without additives such as fatty acids, the complex forms a stable and reproducible Langmuir-Blodgett (LB) multilayer film above a surface pressure of 15 mN m-1. Strong emission from the LB films, even monolayer, was observed. Comparing the relative emission intensity of the MMLCT band for transferred LB monolayer film with that for cast films, we concluded that Pt-Pt interactions are suppressed in the LB film. Instead, the emission at 600 nm arising from the ligand-ligand pi-pi interacted excited state became dominant. The results would provide the insight into the control of molecular ordering for planar Pt complexes from the viewpoint of characteristic excited states.     

Dis-aggregation of an insoluble porphyrin in a calixarene matrix: characterization of aggregate modes by extended dipole model

In this paper, the different aggregation modes of a water-insoluble porphyrin (EHO) mixed with an amphiphilic calix[8]arene (C8A), at the air-water interface and in Langmuir-Blodgett (LB) film form, are analyzed as a function of the mixed composition. The strategy used to control the EHO aggregation has consisted of preparing mixed thin films containing EHO and C8A, in different ratios, at the air-water interface. Therefore, the increase of the C8A molar ratio in the mixed film diminishes the aggregation of the EHO molecules, although such an effect must be exclusively related to the dilution of the porphyrin. The reflection spectra of the mixed C8A-EHO films registered at the air-water interface, show a complex Soret band exhibiting splitting, hypochromicity and broadening features. Also, during the transfer process at high surface pressure, it has been shown that the EHO molecules are ejected from the C8A monolayer and only a fraction of porphyrin is transferred to the solid support, in spite of a complete transfer for the C8A matrix. The complex structure of the reflection spectra at the air-water interface, as well as the polarization dependence of the absorption spectra for the mixed LB films, indicate the existence of four different arrangements for the EHO hosted in the C8A matrix. The aggregate formation is governed by two factors: the attraction between the porphyrin rings which minimizes their separation, and the alkyl chain interactions, that is, hydrophobic effect and/or steric hindrance which determine and restrict the possible aggregation structures. By using the extended dipole model, the assignment of the spectral peaks observed to different EHO aggregates is shown.     

Fabrication of electrochemical transistor based on pi-conjugate polymer Langmuir-Blodgett film

We fabricated an efficient organic electrochemical transistor (OECT) composed of polymer Langmuir-Blodgett (LB) film. The pi-conjugated polymer LB film, which was constructed from a poly(N-dodecylacrylamide) (pDDA) and poly(3-hexylthiophene) (PHT) mixture, was used as a conduction channel layer to connect source and drain electrodes. The mixed-polymer LB film was characterized using UV-vis spectroscopy, X-ray diffraction (XRD), atomic force microscopy (AFM), and cyclic voltammetry. Subsequent UV spectra measurements, XRD measurements, and AFM measurements show that PHT forms a crystalline lamellar domain in the layered structure of pDDA. The OECT included 10 layers of the mixed-polymer LB film as the conduction channel layer. The OECT showed an on/off ratio of 1.1x10(4) and mobility of 7.5x10(-2) cm2 V(-1) s(-1) at low gate (VG=-1.2 V) and source-drain voltages (VDS=-0.5 V). Moreover, the necessary charge to operate the OECT was 1.1x10(-9) mol of e(-1) cm(-2), which was 2 orders smaller than the value reported using a similar device structure. The relatively high on/off ratio and low charge consumption suggest that this OECT, which is fabricated from pi-conjugated polymer LB films, is applicable to macroelectronic devices.     

Interaction between organophosphorous hydrolase and paraoxon studied by surface chemistry in situ at air-water interface

Subphase conditions have been optimized to obtain stable organophosphorous hydrolase (OPH-EC 3.1.8.1) as Langmuir films. The Langmuir film was characterized by surface pressure and surface potential-area isotherms and UV-Vis spectroscopy in situ. The interaction of an organophosphorous compound, namely Paraoxon, with the OPH film was investigated for various surface pressures. The stability of the monolayer and the evidence of the enzyme activity at air-water interface support the use of enzyme LB films as biosensor.     

Pure and mixed films of a nitrostilbene derivative at the air-water interface, Langmuir-Blodgett multilayer fabrication, and optical characterization

This paper reports the preparation and characterization of pure Langmuir and Langmuir-Blodgett (LB) films of a stilbene derivative containing two alkyl chains, namely 4-dioctadecylamino-4'-nitrostilbene. Mixed films incorporating docosanoic acid and the stilbene derivative are also studied. Brewster angle microscopy (BAM) analysis has revealed the existence of randomly oriented three-dimensional (3D) aggregates, spontaneously formed immediately after the spreading process of the stilbene derivative onto the water surface. These 3D aggregates coexist with a Langmuir film that shows the typical gas, liquid, and solid-like phases in the surface pressure and surface potential vs area per molecule isotherms, indicative of an average preferential orientation of the stilbene compound at the air-water interface, and a gradual molecular arrangement into a defined structure upon compression. A blue shift of 55 nm of the reflection spectrum of the Langmuir film with respect to the spectrum of a chloroform solution of the nitrostilbene indicates that two-dimensional (2D) H-aggregates are formed at the air-water interface. The monolayers are transferred undisturbed onto solid substrates with atomic force microscopy (AFM) revealing that the one layer LB films are constituted by a monolayer of the stilbene derivative together with some 3D aggregates. When the nitrostilbene compound is blended with docosanoic acid, the 3D aggregation is avoided in the Langmuir and Langmuir-Blodgett films, but does not limit the formation of 2D H-aggregates, desirable for second-order nonlinear optical response in the blue domain. The AFM images of the mixed LB films show that they are formed by a docosanoic acid monolayer and, on the top of it, a bilayer of the stilbene derivative.     

Langmuir-Blodgett films of octadecanethiol--properties and potential applications

Octadecanethiol (ODT) is known to form self-assembled monolayer on noble metal surfaces which has potential technological applications. Langmuir-Blodgett (LB) technique is another useful method of obtaining highly ordered assembly of molecules. It is of interest to find whether ODT molecules can also form a stable Langmuir monolayer which facilitates the preparation of LB films. In literature, it has been reported that ODT molecules form an unstable Langmuir monolayer. We have studied the stability of the monolayer of the ODT molecules at air-water interface using surface manometry and microscopy techniques. We find the monolayer to be stable on ultrapure water of resistivity greater than 18MOmega cm. However, the behavior changes in the presence of even small amount of additives like NaOH or CdCl2 in the subphase. Our AFM studies on the LB films of ODT deposited from ion-free ultrapure water showed streak-like bilayer domains. The LB films of ODT deposited from CdCl2 containing aqueous subphase yield dendritic domains of the complexed unit grown over ODT monolayer. These nanostructures on surfaces may have potential applications in molecular electronics.     

Deposition and photopolymerization of phase-separated perfluorotetradecanoic acid-10,12-pentacosadiynoic acid Langmuir-Blodgett monolayer films

Mixed monolayer surfactant films of perfluorotetradecanoic acid and the photopolymerizable diacetylene molecule 10,12-pentacosadiynoic acid were prepared at the air-water interface and transferred onto solid supports via Langmuir-Blodgett (LB) deposition. The addition of the perfluoroacid to the diacetylene surfactant results in enhanced stabilization of the monolayer in comparison with the pure diacetylene alone, allowing film transfer onto a solid substrate without resorting to addition of cations in the subphase or photopolymerization prior to deposition. The resulting LB films consisted of well-defined phase-separated domains of the two film components, and the films were characterized by a combination of atomic force microscope (AFM) imaging and fluorescence emission microscopy both before and after photopolymerization into the highly emissive "red form" of the polydiacetylene. Photopolymerization of the monolayer films resulted in the formation of diacetylene bilayers, which were highly fluorescent, with the apparent rate of photopolymerization and the fluorescence emission of the films being largely unaffected by the presence of the perfluoroacid.