均匀负载氧化镍纳米颗粒多孔硬碳球的制备及其高性能锂离子电池负极材料应用

利用水热法制备了粒径为90-130 nm的多孔硬碳球, 并通过浸渍与煅烧的方法制备了硬碳球均匀负载纳米氧化镍颗粒(~10 nm)复合材料. 硬碳球的表面官能团和内部的微孔保证了氧化镍颗粒在硬碳上的均匀分布. 在100 mA·g^-1的电流密度下, 复合材料电极首次充电比容量高达764 mAh·g^-1; 在100 mA·g^-1的电流密度下循环100 个周期后电极充电比容量保持在777 mAh·g^-1, 容量保持率为101%; 800 mA·g^-1电流密度下电极的充电比容量达380 mAh·g^-1, 显示复合材料电极具有优异的循环性能和倍率性能. 硬碳的表面官能团和内部微孔为氧化镍提供了优先形核位点, 保证了二者的牢固结合, 使复合材料获得了“协同效应”, 从而使复合电极具备更短的锂离子扩散路径、更高的电导率和更多的锂离子脱嵌位点. 这种方法还可用于制备硬碳/其他金属氧化物复合材料.     

纳米CoFe2O4/GNS负极制备及其电化学性能研究

采用溶剂热法一步合成纳米尺寸CoFe₂O₄/GNS复合材料（直径约为15 nm）,其颗粒尺寸均一,且均匀分散于石墨烯表面. 电化学测试结果表明,该复合物电极具有良好的循环和倍率性能,500 mA·g^-1电流密度下100周期循环比容量稳定在709 mAh·g^-1, 容量保持率高达95.8%;2 A·g^-1电流密度,其比容量仍高达482 mAh·g^-1.     

SiO_2/C复合负极材料的制备及其性能

采用在纳米SiO2表面包覆聚苯胺,并经过热处理后,制备了SiO2/C纳米复合材料.通过X射线衍射(XRD)、热重分析(TGA)、扫描电子显微镜(SEM)和透射电子显微镜(TEM)对材料的晶体结构和表观形貌进行了表征.同时也对材料的电化学性能进行了测试,结果表明,50 mA/g电流密度下,SiO2/C纳米复合材料首次放电比容量达到830.5 mAh/g,100次循环后,放电比容量仍然保持在510 mA/g以上.电化学交流阻抗测试表明,SiO2表面包覆的碳层能显著减小电极的界面阻抗,提高电池的电化学性能.     

纳米级LiFePO_4材料的水热模板法合成及其性能研究

采用水热模板法合成纳米级LiFePO4材料,改变水热反应中表面活性剂(十六烷基三甲基溴化铵)的比例控制样品颗粒生成的大小.SEM测试表明,合成的LiFePO4晶粒尺寸与表面活性剂的配比密切相关,范围在几十到几百nm之间.充放电试验表明,合成的纳米级LiFePO4材料电极具有优良的电化学性能,其0.1C放电最高比容量可达150 mAh/g,而1C和2C放电比容量也分别有140 mAh/g和126 mAh/g.     

基于镍丝负载氧化镍纳米片的尿酸生物传感器

利用水热法与高温热处理相结合, 在金属镍丝表面制备了氧化镍纳米片, 这些纳米片相互交错, 均匀覆盖于镍丝表面, 其宽度约为数百纳米, 厚度约10 nm. 将镍丝负载氧化镍纳米片吸附固定尿酸氧化酶后, 得到尿酸生物传感器电极, 该电极显示出优异的电化学性能, 其灵敏度达到821.4 μA/(mmol·cm²), 线性检测范围为1~900 μmol/L, 检出限为0.1 μmol/L, 同时具有良好的抗干扰特性. 该尿酸传感器电极易于进行植入式探测或与微流控技术相结合, 为快速、 高灵敏的尿酸检测提供了新途径.     

多孔碳纳米片的合成及在钠离子电池中的应用

本文以氯化钠为硬模板、硝酸镍为金属源、葡萄糖为碳源,在氮气气氛中于750 ^oC通过一步热解法合成嵌镍碳纳米片,然后经酸处理得到多孔碳纳米片. 通过扫描电镜（SEM）、透射电镜（TEM）、拉曼光谱（Raman）和比表面积测定（BET）表征多孔碳纳米片的形貌和结构. 结果显示：多孔碳纳米片孔分布均匀,孔径大小均一;经过酸处理后,碳材料的石墨化程度降低;具有较大的比表面积（约340 m²•g^-1）. 电化学测试表明,电极在100mA•g^-1电流密度下,经过200周循环放电后比容量可维持在309.4 mAh•g^-1,甚至在1000 mA•g^-1 的大电流下其放电比容量仍然可达到173mAh•g^-1,表现出良好的循环稳定性和倍率性能,其在钠离子电池负极材料方面具有潜在的应用前景.     

纳米氧化镍修饰电极电化学测定水中痕量砷(Ⅲ)

采用循环伏安法在玻碳电极(GCE)表面电沉积了氧化镍纳米粒子,制备了纳米氧化镍粒子修饰玻碳电极(NiO-GCE).采用交流阻抗法和循环伏安法对固载纳米氧化镍的玻碳电极的结构和性能进行表征.研究发现:在pH 7.5的磷酸盐缓冲溶液中,在0.9 V电位处,NiO-GCE对砷(Ⅲ)具有良好的催化性能,氧化峰电流与砷(Ⅲ)的浓度在1.5×10-6～3.8×10-4mol·L-1范围内呈线性关系,检出限(3S/N)为5.0×10-7mol·L-1.     

粒径可控纳米LiFePO4/C的制备及其电化学性能研究

LiFePO4电极的倍率特性与材料的粒度和电子导电性有很大关系.采用共沉淀方法,调控预处理温度,将3种不同尺寸的FePO4前驱体通过表面修饰对-羟基苯甲酸的聚合物,可合成不同尺度的LiFePO4/C材料,分别为80 nm、200nm和1μm.纳米尺度LiFePO4-a/C电极,30C放电比容量达到了100 mAh·g-1,而微米级LiFePO4-c/C电极放电比容量仅为54mAh·g-1.均一碳包覆的LiFePO4/C电极表现出强抗氧化性,不仅提高其导电性,还可防止材料氧化.     

Ni3S2@碳纳米管复合材料的制备及其储钠性能

采用一步固相煅烧工艺制备了碳纳米管原位封装Ni₃S₂纳米颗粒（Ni₃S₂@CNT）,并研究了其作为钠离子电池（SIBs）负极材料的电化学性能. 通过X射线衍射（XRD）、扫描电子显微镜（SEM）、透射电子显微镜（TEM）、循环伏安测试、恒流充放电以及交流阻抗等研究了Ni₃S₂@CNT的物相结构、形貌特征以及电化学性能. 电化学测试表明,材料在100 mA·g ^-1电流密度下,放电容量可以达到541.6 mAh·g ^-1,甚至在2000 mA·g ^-1的大电流密度下其放电比容量也可以维持在274.5 mAh·g ^-1. 另外,材料在100 mA·g ^-1电流密度下,经过120周充放电循环后其放电和充电比容量仍然可以保持在374.5 mAh·g ^-1和359.3 mAh·g ^-1,说明其具有良好倍率性能和循环稳定性能. 良好的电化学性能归因于这种独特的碳纳米管原位封装Ni₃S₂纳米颗粒结构. 碳纳米管不但可以提高复合材料的导电性,也可以缓冲Ni₃S₂纳米颗粒在反复充放电过程中产生的体积膨胀效应,明显改善了Ni₃S₂@CNT负极复合材料的电化学性能.     

水热对纳米氢氧化镍电化学性能的影响

本文采用微乳法制备纳米氢氧化镍,采用X射线衍射（XRD）、扫描电镜（SEM）、透射电镜（TEM）、恒流充放电、循环伏安、交流阻抗等方法研究纳米氢氧化镍的微观结构、表面形貌和电化学性能。实验结果表明：140℃水热和微乳/水热两种方式处理得到的纳米氢氧化镍具有不同形貌特征。水热和微乳/水热处理虽然不影响纳米氢氧化镍的活化性能,但对纳米氢氧化镍的放电比容量影响很大,采用140℃水热和微乳/水热处理比单纯的微乳法制备得到的纳米氢氧化镍的放电比容量分别提高了62.6 mAh/g和112.8 mAh/g。而且,处理后的纳米氢氧化镍的循环伏安峰电流增大、电荷转移电阻由2.633 Ω分别降至2.464 Ω和1.679 Ω。     

Microwave assisted hydrothermal synthesis of tin niobates nanosheets with high cycle stability as lithium-ion battery anodes

SnNb₂O₆ and Sn₂Nb₂O₇ nanosheets were synthetized via microwave assisted hydrothermal method, and innovatively employed as anode materials for lithium-ion battery. Compared with Sn₂Nb₂O₇ and the previously reported pure Sn-based anode materials, the SnNb₂O₆ electrode exhibited outstanding cycling performance.     

Catalytically Active CoSe2 Supported on Nitrogen-Doped Three Dimensional Porous Carbon as a Cathode for Highly Stable Lithium-Sulfur Battery

Lithium-sulfur batteries are promising secondary energy storage devices that are mainly limited by its unsatisfactory cyclability owing to inefficient reversible conversion of sulfur and lithium sulfide on the cathode during the discharge/charging process. In this study, nitrogen-doped three-dimensional porous carbon material loaded with CoSe₂ nanoparticles (CoSe₂-PNC) is developed as a cathode for lithium-sulfur battery. A combination of CoSe₂ and nitrogen-doped porous carbon can efficiently improve the cathode activity and its conductivity, resulting in enhanced redox kinetics of the charge/discharge process. The obtained electrode exhibits a high discharge specific capacity of 1139.6 mAh g⁻¹ at a current density of 0.2 C. After 100 cycles, its capacity remained at 865.7 mAh g⁻¹ thus corresponding to a capacity retention of 75.97 %. In a long-term cycling test, discharge specific capacity of 546.7 mAh g⁻¹ was observed after 300 cycles performed at a current density of 1 C.     

A novel synthesis of Nb_2O_5@rGO nanocomposite as anode material for superior sodium storage

The development of novel anode materials,with superior rate capability,is of utmost significance for the successful realization of sodium-ion batteries(SIBs).Herein,we present a nanocomposite of Nb_2 O_5 and reduced graphene oxide(rGO) by using hydrothermal-assisted microemulsion route.The water-in-oil microemulsion formed nanoreactors,which restrained the particle size of Nb_2 O_5 and shortened the diffusion length of ions.Moreover,the rGO network prevented agglomeration of Nb_2 O_5 nanoparticles and improved electronic conductivity.Consequently,Nb_2 O_5@rGO nanocomposite is employed as anode material in SIBs,delivering a capacity of 195 mAh/g after 200 charge/discharge cycles at 0.2 A/g.Moreover,owing to conductive rGO network,the Nb_2 O_5@rGO electrode rende red a specific capacity of 76 mAh/g at high current density of 10 A/g and maintained 98 mAh/g after 1000 charge/discharge cycles at 2 A/g.The Nb_2 O_5@rGO electrode material prepared by microemulsion method shows promising possibilities for application of SIBs.     

MnS hollow microspheres combined with carbon nanotubes for enhanced performance sodium-ion battery anode

MnS as anode material for sodium-ion batteries (SIBs) has recently attracted great attention because of the high theoretical capacity, great natural abundance, and low cost. However, it suffers from inferior electrical conductivity and large volume expansion during the charge/discharge process, leading to tremendous damage of electrodes and subsequently fast capacity fading. To mitigate these issues, herein, a three-dimensional (3D) interlaced carbon nanotubes (CNTs) threaded into or between MnS hollow microspheres (hollow MnS/CNTs composite) has been designed and synthesized as an enhanced anode material. It can effectively improve the electrical conductivity, buffer the volume change, and maintain the integrity of the electrode during the charging and discharging process based on the synergistic interaction and the integrative structure. Therefore, when evaluated as anode for SIBs, the hollow MnS/CNTs electrode displays enhanced reversible capacity (275 mAh/g at 100 mA/g after 100 cycles), which is much better than that of pure MnS electrode (25 mAh/g at 100 mA/g after 100 cycles) prepared without the addition of CNTs. Even increasing the current density to 500 mA/g, the hollow MnS/CNTs electrode still delivers a five times higher reversible capacity than that of the pure MnS electrode. The rate performance of the hollow MnS/CNTs electrode is also superior to that of pure MnS electrode at various current densities from 50 mA/g to 1000 mA/g.     

一种新型锂离子电池有机正极材料—聚硫化冉酸(PSCA)的合成及表征

成功合成了一种新型锂离子电池正极材料—聚硫化冉酸(PSCA).固体核磁13C谱、FT-IR及电化学等测试表明,氯冉酸经过硫化之后,硫取代氯的位置而得到目标产物聚硫化冉酸(PSCA).在1.5～3.6V的电位区间内,以15mAh/g的电流密度作充放电测试,首次放电比容量高达287.6mAh/g,循环100圈后容量依然保持为169.9mAh/g.     

Oleic acid-treated synthesis of MnO@C with superior electrochemical properties

MnO@C nanocomposites are synthesized by annealing MnO microspheres treated with oleic acid as carbon source. The obtained MnO@C nanocomposites exhibit a discharge capacity of 1075 m Ah/g for the initial cycle, and show the excellent cycling performance with a discharge capacity of 421 mAh/g after100 cycles at a current density of 100 mA/g. The total specific capacity of MnO@C nanocomposites is higher than those of pure MnO microspheres in our experiments. Owing to the superior electrochemical behavior, the as-obtained MnO@C nanocomposites are potentially applied as next-generation anode material for lithium-ion batteries.     

Nitrogen doped porous carbon as excellent dual anodes for Li- and Na-ion batteries

Biomass-derived carbon materials have obtained great attention due to their sustainability,easy availability,low cost and environmentally benign.In this work,bamboo leaves derived nitrogen doped hierarchically porous carbon have been efficiently synthesized via an annealing approach,followed by an etching process in HF solution.Electrochemical measurements demonstrate that the unique porous structure,together with the inherent high nitrogen content,endow the as-derived carbon with excellent lithium/sodium storage performance.The porous carbon annealed at 700℃presents outstanding rate capability and remarkable long-term stability as anodes for both lithium-ion batteries and sodium-ion batteries.The optimized carbon delivers a high discharge capacity of 450 mAh/g after 500 cycles at the current density of 0.2 A/g for LIBs,and a discharge capacity of 180 mAh/g after 300 cycles at the current density of 0.1 A/g for SIBs.     

锂离子电池正极材料Na3V2（PO4）2F3的原位XRD及固体核磁共振研究

采用溶胶凝胶法制备Na3V2（PO4）2F3/C复合材料,该材料具有优异的电化学循环性能和倍率性能.利用电化学原位同步辐射X射线衍射（XRD）及魔角旋转固体核磁共振（MASSS-NMR）技术研究了Na3V2（PO4）2F3材料充放电过程中结构变化过程及Li/Na嵌入-脱出反应.研究结果表明,Na3V2（PO4）2F3的电极反应按嵌入-脱出反应机理进行,充放电过程中材料具有优异的结构稳定性.我们还发现Na3V2（PO4）2F3与电解液接触后与电解液中的Li＋发生部分交换反应形成LixNa3-xV2（PO4）2F3.在首次充电时,Li＋和结构中Na1位置的Na＋共同从晶格中脱出;而首次放电过程中,Na＋和Li＋共同嵌入到晶格中;充放电过程中发生的是Li＋和Na＋的共嵌入-脱出反应.     

Nanostructured Carbon/Antimony Composites as Anode Materials for Lithium‐Ion Batteries with Long Life

A series of nanostructured carbon/antimony composites have been successfully synthesized by a simple sol–gel, high‐temperature carbon thermal reduction process. In the carbon/antimony composites, antimony nanoparticles are homogeneously dispersed in the pyrolyzed nanoporous carbon matrix. As an anode material for lithium‐ion batteries, the C/Sb10 composite displays a high initial discharge capacity of 1214.6 mAh g^?1 and a reversible charge capacity of 595.5 mAh g^?1 with a corresponding coulombic efficiency of 49 % in the first cycle. In addition, it exhibits a high reversible discharge capacity of 466.2 mAh g^?1 at a current density of 100 mA g^?1 after 200 cycles and a high rate discharge capacity of 354.4 mAh g^?1 at a current density of 1000 mA g^?1. The excellent cycling stability and rate discharge performance of the C/Sb10 composite could be due to the uniform dispersion of antimony nanoparticles in the porous carbon matrix, which can buffer the volume expansion and maintain the integrity of the electrode during the charge–discharge cycles.