Biodegradability study of polylactic acid/ thermoplastic polyurethane blends

Blends with varied ratio of polylactic acid (PLA) and thermoplastic polyurethane (TPU) were prepared by melt blending. The PLA content in blends was 20, 40, 60 and 80 wt%. Samples of pure PLA and TPU that underwent the same thermal treatment were also prepared. Biodegradation was examined by respirometry. Pure TPU started to degrade immediately due to degradation of the low molecular weight plasticizer in the polymer. Pure PLA, on the other hand, exhibited an incubation period after which degradation progressed rapidly and was almost complete after 70 days. The degradation profile of the blends can be correlated to their morphology. Samples with a co-continuous morphology initially degrade at a higher rate than the rest of the samples due to the higher exposure of the TPU phase in these blends.     

Effect of ethylene-co-vinyl acetate-glycidylmethacrylate and cellulose microfibers on the thermal,rheological and biodegradation properties of poly(lactic acid) based systems

The properties and biodegradation behavior of blends of poly(lactic acid) (PLA) and ethylene-vinyl acetate-glycidylmethacrylate copolymer (EVA-GMA), and their composites with cellulose microfibers (CF) were investigated. The blends and composites were obtained by melt mixing and the morphology, phase behavior, thermal and rheological properties of PLA/EVA-GMA blends and PLA/EVA-GMA/CF composite films were investigated as a function of the composition. The disintegrability in composting conditions was examined by means of morphological, thermal and chemical analyses to gain insights into the post-use degradation processes. The results indicated a good compatibility of the two polymers in the blends with copolymer content up to 30 wt.%, while at higher EVA-GMA content a phase separation was observed. In the composites, the presence of EVA-GMA contributes to improve the interfacial adhesion between cellulose fibers and PLA, due to interactions of the epoxy groups of GMA with hydroxyls of CF. The addition of cellulose microfibers in PLA/EVA-GMA system modifies the rheological behavior, since complex viscosity increased in presence of fibers and decreased with an increase in frequency. Disintegration tests showed that the addition of EVA-GMA influence the PLA disintegration process, and after 21 days in composting conditions, blends and composites showed faster degradation rate in comparison with neat PLA due to the different morphologies induced by the presence of EVA-GMA and CF phases able to allow a faster water diffusion and an efficient PLA degradation process.     

Probing the tribological behaviors in water of novel poly(phthalazione ether sulfone ketone) and its composites based on the state of aggregation and the microstructure

In this paper, novel poly(phthalazione ether sulfone ketone) (PPESK) and its composites reinforced with carbon fibers (CFs) were prepared, and their tribological behaviors in pure and sea water were comparatively investigated. Affected by the noncoplanar twisted aromatic structure in the molecular skeleton, the aggregation of the macromolecular chain in PPESK was amorphous, resulting in very high water absorption of PPESK matrix. The invading water molecules led to a sharp decrease in the hardness of PPESK surface, resulting in very high wear rate of PPESK in water. Although CF/PPESK composites had higher water absorption than pure PPESK, their wear processes in water were no longer dominated by high water absorption but by the load‐carrying effect of CFs, ascribed to the good CF/PPESK interfacial adhesion. Therefore, CF/PPESK composites exhibited very low wear rates in the order of 10^?7 mm³/Nm in water, which decreased with the CF content increasing until the content of CFs reached 50%. The results revealed that the most critical factor determining the wear behavior of a fiber‐reinforced polymer composite sliding in water is the fiber/matrix interface but not the water absorption of the polymer matrix. Copyright © 2017 John Wiley & Sons, Ltd.     

Biodegradation of sequentially surface treated lignocellulose reinforced polylactic acid composites: Carbon dioxide evolution and morphology

Maple fibres were treated with a variety of sequential treatments, namely sodium hydroxide (NaOH), NaOH followed by acetylation, or NaOH followed by silanation. These fibres were incorporated into a polylactic acid (PLA) composite and the biodegradation effects were investigated. After 124 days, all composites had exceeded 90% biodegradation with most close to 100%. The PLA composite with the NaOH-treated fibres had the quickest onset of degradation (4.9 days) and highest peak rate of degradation (1.77% biodegradation/day) of all composites studied. Neat PLA had a similarly high peak rate of degradation at 1.85% biodegradation/day, but had a later onset of 11 days. Gel permeation chromatography (GPC) analysis showed the earlier onset of degradation of the composites was caused by increased hydrolysis during composite fabrication as well as composting. GPC showed the formation of up to three molecular weight bands in the PLA during composting which were hypothesised to be occurring by surface hydrolysis, bulk hydrolysis and hydrolysis at the fibre interface. Analysing the remaining composite revealed the NaOH treatment not only caused an increased rate of degradation in the PLA through increase fibre porosity, but also caused an increased rate of degradation in the fibre from the lack of surface waxes and hemicellulose. Similar, yet slower, behaviours were also seen in the NaOH followed by acetylation and NaOH followed by silane treated composites with all composites degrading more rapidly than the neat PLA and neat maple fibre samples.     

Mechanical and flame‐retardant properties of biodegradable polylactide composites with hyperbranched silicon‐containing polymer

A hyperbranched polymer (HBP‐B2) containing siloxane chains was synthesized via bulk polymerization of diepoxide with a primary amine in the presence of monoepoxide. The weight‐average molecular weight of the prepared polymers was approximately 9200. Composites of polylactide (PLA) with aluminum trihydroxide (ATH) and the HBP‐B2 were prepared via direct melt compounding using a brabender. The test results showed that the LOI could be raised to 34% for the PLA composite with 25 wt% ATH and 5% HBP‐B2. The surface thermal profile of the composite during UL94 V test was further captured by an infrared camera, which was helpful to understand the flame‐retardant properties of the different samples. A V‐0 rating could be achieved by adding ATH and HBP‐B2 to the PLA matrix. Incorporation of HBP‐B2 as a plasticizer could increase the impact strength of a PLA blend or composite. For example, an addition of 10 wt% of HBP and 20 wt% ATH increased the elongation at break from 5% for neat PLA to 155% for the PLA composite.     

基体分子运动对聚偏氟乙烯/碳纤维复合材料的聚合物基正温度系数性能的影响

聚合物基正温度系数(PTC)材料中,基体分子在熔体状态下的运动能力可显著影响填料分布、PTC强度及稳定重复性等,明确其机理有利于高灵敏性且稳定可重复的PTC复合材料的设计与制备.通过探究基体熔体黏度不同的聚偏氟乙烯(PVDF)/碳纤维(CF)的电阻-温度响应行为,可以发现复合材料PTC转变温度区间仅取决于基体化学结构与...     

Electrical and dielectric properties in carbon fiber‐filled LMWPE/UHMWPE composites with different blend ratios

Carbon fiber (CF) filled low‐molecular‐weight polyethylene (LMWPE) and ultra‐high molecular weight polyethylene (UHMWPE) composites were prepared by the gelation from solution and the kneading in the melting state. The content of carbon fibers was fixed to be 23.5 vol %. The resistivity, positive temperature coefficient (PTC), and dielectric behaviors of the composites became more pronounced with increasing content of LMWPE with much higher thermal expansion than that of UHMWPE. The PTC effect became most significant, when the blend ratio of LMWPE to UHMWPE was 9/1. Beyond 9/1, the PTC effect was less pronounced. Scanning electron microscopy (SEM) and differential scanning calorimetry (DSC) revealed that the UHMWPE and LMWPE chains within the composite crystallized independently by gelation from solution and were virtually unaffected by the presence of carbon fibers. Consequently, it was confirmed that carbon fibers selectively were localized in the mixed region of LMWPE and UHMWPE for the composite (3/1 and 6/1) and mainly in the region of LMWPE for the 9/1, 12/1, and 15/1 composites. This indicated that the content of carbon fibers within LMWPE region was the highest for the 9/1 composite and the 9/1 composite provides the most significant PTC effect. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 359–369, 2008     

PTC/NTC Behavior of PVDF Composites Filled with GF and CF

Conductive polyvinylidene fluoride（PVDF）matrix composites filled with graphited fiber（GF）or carbon fiber（CF）were prepared by the melt-mixing method.The breakage and length distribution of the fibers in the polymer matrix were studied by scanning electron microscope（SEM）and optical microscope（OM）observations,respectively. The differences in the positive temperature coefficient（PTC）effects of the composites were mainly attributed to inter-fiber contact ability.The elimination of the negative temperature coefficient（NTC）effect for CF/PVDF composite was because of an increase in the viscosity of the polymer matrix.With the same filler content,CF could be more effective,to eliminate the NTC effect when compared with GF.Addition of 2%CF（mass fraction）in the PVDF composite with 7%GF（mass fraction）could effectively eliminate the NTC phenomenon of the composite.     

The effect of heat treatment on water sorption in polylactide and polylactide composites via changes in glass‐transition temperature and crystallization kinetics

Water sorption into polylactide (PLA) and polylactide‐montmorillonite (PLLA‐MONT) composites containing 5 wt % of montmorillonite (MONT) under different heat treatment conditions was studied using the quartz crystal microbalance/heat conduction calorimetry (QCM/HCC) technique. Results showed that water sorption in neat polymer films and composite films increased with heat treatment temperature up to 120 °C. Differential scanning calorimetry was used to measure the glass‐transition temperature and isothermal crystallization kinetics of all samples. The mobility of the amorphous domain in all samples increased with heat treatment temperature, indicated by the decrease in glass‐transition temperature. PLA composites crystallized at a much faster rate than neat PLA did because MONT acted as a nucleating agent. Under the same heat treatment condition, water sorption in PLLA‐MONT composites was always higher than that in neat PLA due to the presence of the hydrophilic hydroxyl groups on the surface of MONT particles. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

A biocompatible composite based on poly(ε‐caprolactone fumarate) and hydroxyapatite

Fabrication of biodegradable composites applicable as hard tissue substitutes consisting of poly(ε‐caprolactone fumarate) (PCLF), methacrylic acid (MAA), and hydroxyapatite (HA) was investigated. PCLF macromers were synthesized by reaction of PCL diol with fumaryl chloride in the presence of propylene oxide and characterized by gel permeation chromatography, FTIR, and ¹H NMR spectroscopy. Composites were fabricated by incorporating HA as inorganic filler in PCLF matrix which followed by thermal curing of the composition using benzoyl peroxide and MAA as a free radical initiator and reactive diluent, respectively. Uniform distribution of the fine ceramic phase in the polymer matrix was elucidated by scanning electron microscopy. The effects of the initial macromer molecular weight and the filler volume fraction on mechanical properties and cytotoxicity of the composites were also examined. Significant enhancement in the mechanical properties was observed upon increasing HA content and/or initial PCLF molecular weight. The biocompatibility of the specimens was also improved with increasing ceramic phase. Copyright © 2010 John Wiley & Sons, Ltd.     

Degradation behavior of poly(lactide-co-glycolide)/β-TCP composites prepared using microwave energy

Biodegradable poly(lactide-co-glycolide) (PLGA)/β-tricalcium phosphate (β-TCP) composites were synthesized through polymerization using microwave energy. The degradation behavior of the PLGA/β-TCP composites was carried out at 37 °C in a SBF without changing the solution in order to examine the effect of β-TCP on the degradation behavior. The changes in the molecular weight, mass, and morphology of the composites were examined with respect to the soaking time. An incubation time of 2 weeks was needed to degrade the β-TCP of the composites, indicating that degradation of β-TCP could be started when β-TCP was detached from the PLGA matrix or exposed from composites surface, caused by PLGA matrix was degraded into the SBF solution. The mass loss of the composites with respect to the soaking time revealed that PLGA transformed from a polymer to an oligomer as the degradation process proceeded. The whisker-like morphological changes, caused by the transformation and degradation of the polymer were observed in the composites after week 2. The degradation behavior of the PLGA/β-TCP composites was influenced by the β-TCP content in the composite, and the degradation rate of the composite could be controlled by the initial molecular weight of PLGA.     

聚乳酸/壳聚糖纳米纤维结构形成的影响条件及其生物矿化活性

以二氧六环/冰醋酸为溶剂体系,采用相分离法制备了聚乳酸(PLA)/壳聚糖(CS)复合纳米纤维结构的组织工程支架,探讨了不同CS含量、不同凝胶温度及不同分子量对PLA/CS复合支架纳米纤维结构的影响以及支架的生物活性。结果表明,凝胶温度对PLA/CS复合材料的纳米纤维结构影响较大,且随着温度的降低,结构的微观尺寸也逐渐增大,从纳米级上升到普通的尺寸结构;CS含量对PLA/CS复合支架的基体结构影响不大;实验范围内PLA分子量对PLA/CS复合支架的纳米纤维结构有重要影响:分子量大的样品,较易得到PLA/CS复合纳米纤维结构的材料,而分子量小的样品则不能得到纳米纤维结构。另外,生物矿化实验表明CS的添加有利于PLA/CS复合材料生物活性的提高。     

Biodegradation and thermal decomposition of poly(lactic acid)-based materials reinforced by hydrophilic fillers

The effect of hydrophilic fillers (starch and wood-flour) on the degradation and decomposition of poly(lactic acid) (PLA) based materials was investigated. Biodegradation was evaluated by composting under controlled conditions in accordance with AS ISO 14855. Thermal decomposition was studied by thermogravimetry (TGA). Morphological variations during biodegradation were investigated by SEM examination. It was found that biodegradation rates of PLA/starch blends and PLA/wood-flour composites were lower than that of pure cellulose but higher than that of pure PLA. The biodegradation rate was increased from about 60% to 80% when the starch content was increased from 10% to 40% after 80 days. Both starch and wood-flour accelerated thermal decomposition of PLA, and starch exhibited a relatively stronger affect then wood-flour. The decomposition temperature of PLA was decreased about 40 °C when the filler content was increased to 40%. Small polar molecules released during thermal decomposition of starch and wood-flour were attributed to the thermal decomposition behaviours of the PLA based blends and composites and their role is further discussed in this paper.     

具有高灵敏性且稳定可重复的正温度系数效应的PVDF/CF导电复合材料

以碳纤维(CF)为填料,聚偏氟乙烯(PVDF)为基体,通过熔融共混法制备PVDF/CF导电复合材料.所得复合材料具有显著的正温度系数(PTC)效应,温度上升到聚合物熔点附近时,电阻率对温度变化敏感.在转折温度区间(155.5~171.0oC,(35)(28)15.5oC)内,其体积电阻率的增加速率约为1.3×105?cm K-1.在不同CF含量下,复合材料表现出不同的PTC行为.随着CF含量的增加,其峰值电阻略有下降.高导电粒子含量下,无负温度系数(NTC)效应.在冷却循环过程,导电网络的重构性良好.复合材料即使经过多次热循环,依然表现出良好的PTC特性重现性.     

Poly(lactic acid)-based polymer composites with high electric and thermal conductivity and their characterization

Electrically and thermally conductive polymer composites on the basis of biodegradable poly(lactic acid) (PLA) were developed and studied in this work. Pristine single-walled carbon nanotubes (CNTs) and powder of natural graphite (G) were used as fillers in polymer composites. PLA-based composites were prepared by melt-compounding method. The volume resistivity of PLA/CNT composites can be changed by more than ten orders of magnitude compared to that for neat PLA. The thermal conductivity of PLA/G composites can be changed from 0.193 W⋅m⁻¹⋅K⁻¹ (neat PLA) up to 2.73 W⋅m⁻¹⋅K⁻¹. Loading small quantity of CNTs into PLA/G composites increases the thermal conductivity not less than by 40% of magnitude. Besides, all developed PLA-based composites are suitable for processing by injection molding, extrusion or additive manufacturing technology (3D printing).     

Mechanical and morphological investigations of UHMWPE/Fe composites

Ultra-high molecular weight polyethylene/iron composites were investigated. The specimens were obtained by pressing in a steel die and sintering at different temperatures. By means of porosimetry, microscopy, microhardness, density, and partial volumes of the components it is shown that there are no microcavities. The microhardness does not depend upon the weight % content of the metal in the composites. It also neither depends on the pressure nor the temperature of sintering. For low metal content within the composites, microhardness Mayer equations are linear. For high metal content the dependence is nonlinear. With the increasing of the iron content tensile strength weakly decreases. However, plane-strain compression, dimension steadiness, Vicat softening temperature, and tribometric characteristics of the composites are improved. It is shown that the polymer is a well-dispersive medium. The particles of the components have a good mechanical compatibility. The polymer wets the surface of the iron; this is probably connected with the surface oxidation of the metal particles.     

聚乳酸/凹凸棒土纳米复合材料的结构与性能

采用熔融复合方法制备了不同填料质量分数的聚乳酸/纳米凹凸棒土复合材料,纳米凹凸棒土的加入可以显著提高聚乳酸纳米复合材料的拉伸强度和断裂伸长率.扫描电镜结果表明,凹凸棒土粒子在复合材料中实现了均匀分散.DSC曲线在降温过程中出现明显结晶峰,说明纳米凹凸棒土对聚乳酸有一定的成核作用.当纳米凹凸棒填料含量>8%时,在聚合物基体中可形成完善的网络状结构.填料粒子作为体系中的物理缠结点使得复合材料熔体的应力松弛时间延长.红外谱图显示纳米凹凸棒土和聚乳酸分子间存在较强的相互作用.我们推测,纳米凹凸棒土的加入减少了PLA基体层的厚度,使其由三维应力转变为二维应变状态,导致最大切应力可以达到剪切屈服强度,产生剪切滑移形变带,使得呈现出韧性材料性质,有效提高了材料的断裂伸长率.     

Poly(lactic acid) Synthesis in Solution Polymerization

The step-growth polymerization of L-lactic acid in solution was studied in this work. In order to attain a polymer with high molecular weight, the water formed during the polymerization must be continuously removed. The use of organic solvents with high boiling point, drying agents and reduced pressure led to poly(lactic acid) (PLA) with high molecular weight, directly from the monomer. Tin (II) chloride dihydrate, SnCl₂.2H₂O, was the best of the catalysts tested as it allowed achieving PLA with a molecular weight close to 80 000 g.mol⁻¹. However, the stereoregurarity control is a severe problem in PLA synthesis by step-growth due to transesterification reactions, which lead to an inversion of the conformation and a decrease of the optical purity of the polymer. Specific rotation measurements were used in this work and showed to be a powerful technique to evaluate the racemization extent. The thermal stability of the PLA samples was evaluated by DSC which exhibits a thermal behaviour similar to the commercial Polylactide.     

Characterization of polylactic acid green composites and its biodegradation in a bacterial environment

The growing interest in the preservation of our environment is pushing for solutions to develop less impacting materials. Thus, the development of biocomposites and is recyclable and compostable end-of-life resources seem an interesting alternative. In this study, the characterization of Polylactic acid (PLA) reinforced with treated and untreated Olive husk flour (OHF) were investigated. More then, their biodegradation with a Bacillus sp. has been evaluated. The main results show that the bacteria degraded both the PLA and the composite. This degradation was confirmed by the release of reducing sugars as well as increasing weight loss of PLA matrix and composites.     

Biodegradation of poly(lactic acid) powders proposed as the reference test materials for the international standard of biodegradation evaluation methods

The methods for producing reference test materials for biodegradation evaluation tests have been studied. Mechanical crushing at low temperature of polymer pellets using dry ice was selected for the method of producing polymer powder of poly(lactic acid) (PLA). The powders were fractionated using 60 mesh (250 μm) and 120 mesh (125 μm) sieves. The size distributions were then measured. The average diameter of the PLA particles obtained by this method was 214.2 μm. The biodegradation speeds of these PLA polymer powders were evaluated by two methods based on the international standard and one in vitro method based on the enzymatic degradation. First, the degree of biodegradation for this PLA powder was 91% for 35 days in a controlled compost determined by a method based on ISO 14855-1 (JIS K6953) at 58 °C managed by the Mitsui Chemical Analysis and Consulting Service, Inc. (Japan). Second, these polymer powders were measured for biodegradation by the Microbial Oxidative Degradation Analyzer (MODA) in a controlled compost at 58 °C and 70 °C based on ISO/DIS 14855-2 under many conditions. The degree of biodegradation for this PLA powder was approximately 80% for 50 days. In addition, the polymer powders were biodegraded by Proteinase K which is a PLA degradation enzyme. This polymer powder was suitable as a reference material for the evaluation methods of biodegradation.