In this work, the polybutadiene (PB) block of an asymmetric lamellae forming polystyrene/polybutadiene based triblock copolymer was epoxidized to different extent in order to study its effect on morphology and mechanical behaviour of the copolymer. The products were analyzed by means of different microscopic techniques, Fourier transform infrared (FTIR) spectroscopy and microhardness measurements. It was found that the microphase separation behavior and hence the mechanical properties of the materials were drastically altered through epoxidation of the diene block of the styrene/diene triblock copolymer. With the increase in the extent of epoxidation the lamellar structure changed to distorted lamellae and then to disordered domains. Consequently, inhomogeneous mechanical performance of the samples was observed at higher degree of chemical modification. 相似文献
By means of transmission electron microscopy (TEM) and uniaxial tensile testing, the connection between the morphology and the micromechanical properties of selected styrene-rich styrene/butadiene block copolymers was studied with respect to their molecular architecture. In particular, the structure-property correlation of a lamellae forming asymmetric linear SBS triblock copolymer was examined by systematically varying the sample preparation techniques and testing temperature. The molecular architecture was found to influence directly the morphology formation of the block copolymers. Different mechanisms such as drawing of the lamellae, shearing in the rubbery phase and rotation of the lamellar axis were observed. From room temperature down to the temperature close to glass transition temperature of the soft phase, a homogeneous plastic drawing of glassy lamellae was perceptible. 相似文献
A simple approach to improve the structural ordering in block copolymer/nanoparticle nanocomposites is presented. It is to blend a small molecular weight homopolymer with the composites, which can uniformly swell the preferred domain where the nanoparticles locate and increase the conformational entropy of the domain. Consequently, the interfaces between the block copolymer domains become smooth that improves the long range order in the nanocomposites. Furthermore, the uniform swelling of the preferred domain by the homopolymer will allow higher loading of nanoparticles without adversely affecting the long range order.
Using transmission electron microscopy (TEM) and tensile testing, we investigated the morphology and the micro-deformation processes in a new kind of highly asymmetric polystyrene/polybutadiene based triblock copolymer and its blends with general purpose polystyrene (GPPS). The emphasis has been put on the analysis of blends morphology evolved under extrusion conditions and the impact of the later on the micromechanical behaviour of the blends. It was found that the phase separated structures were strongly oriented along the extrusion direction leading to the anisotropic mechanical behaviour. The blends showed more ductile performance and lesser strength on loading the sample perpendicular to the extrusion direction. The ductile to brittle transition was observed when the morphology of the blends was dominated by the glassy phase for 60 wt.-% GPPS. 相似文献
A facile and electrostatically driven approach has been developed to prepare bicontinuous polymer nanocomposites that is based on the polyoxometalate (POM) macroion induced phase transition of PS-b-P2VP from an initial lamellar phase to a stable bicontinuous phase. The multi-charged POMs can electrostatically cross-link P2VP blocks and give rise to bicontinuous phases in which the POM hybrid conductive domains occupy a large volume fraction of more than 50 %. Furthermore, the POMs can give rise to high proton conductivity and serve as nanoenhancers, endowing the bicontinuous nanocomposites with a conductivity of 0.1 mS cm−1 and a Young's modulus of 7.4 GPa at room temperature; these values are greater than those of pristine PS-b-P2VP by two orders of magnitude and a factor of 1.8, respectively. This approach can provide a new concept based on electrostatic control to design functional bicontinuous polymer materials. 相似文献
The influence of homopolymer molecular weight and compression moulding on morphology formation and deformation behaviour of binary blends of polystyrene-polybutadiene based star block copolymer and polystyrene (PS) homopolymer was investigated. The samples used were a polystyrene-(polystyrene-co-polybutadiene)-polystyrene (S-S/B-S) star block copolymer and anionically prepared polystyrene (aPS). The techniques used were transmission electron microscopy (TEM) and uniaxial tensile testing. A wide range of segregation behaviour was observed depending on the ratio of the length of aPS chains relative to that of corresponding outer blocks of the block copolymer. For the first time, the formation of macrophase-separated ‘droplet-like’ morphology has been reported, which endows the block copolymer/polystyrene blends with higher toughness. The mechanical properties of blends are discussed in the light of micromechanical processes of deformation. The micromechanical mechanisms and their dependence with inter domain distance are similar to the mechanisms found in rubber network toughened systems. 相似文献
We report here on the formation of hybrid compound block copolymer micelles encapsulating gold nanoparticles, utilizing a direct and general preparation method. The giant hybrid compound micelles are structured with micelles of PS‐b‐P2VP with gold nanoparticles in their P2VP core and PI‐b‐PS chains as the outer part of the compound micelles. The gold nanoparticles were produced using gold ion‐loaded PS‐b‐P2VP micelles as a nanoreactor, in a PS selective solvent (toluene), by the subsequent reduction of gold ions. The synthesis of the gold nanoparticles was monitored by UV‐vis spectroscopy. The gold containing micelles were then encapsulated in larger micelles of PI‐b‐PS copolymer, by successive utilization of toluene and heptane with the intermediate evaporation of toluene. The nanoassembly of the compound materials comprised a PI corona and a PS compound core, with P2VP/Au0 domains, and was characterized using UV‐vis spectroscopy, dynamic light scattering and transmission electron microscopy.
Summary: Polymer nanocomposites formed from organically modified montmorillonite offer the promise of greatly improved properties over those of the matrix polymer, provided the organoclay can be dispersed, or exfoliated, into the polymer matrix to generate high aspect ratio particles. The exfoliation of organoclays in two series of ethylene-based polymers, ethylene-vinyl acetate copolymers and sodium ionomers of ethylene-methyacrylic acid copolymers, is described along with the properties of these nanocomposites. 相似文献
In this work the primary mechanical property profiles of a specific class of nano‐structured polymer/inorganic hybrid materials are characterized. By utilizing sol‐gel aluminosilicate synthesis with amphiphilic polyisoprene‐block‐poly(ethylene oxide) block copolymers as structure‐directing agents, block copolymer/aluminosilicate hybrid materials are prepared with nanometer scale hexagonally packed cylinders and lamellae of the inorganic hybrid components, as evidenced by small‐angle X‐ray scattering. Systematic thermal and dynamic mechanical analyses are performed on these hybrids as well as on the constituting components. Results reveal two transitions from the low temperature, glassy state of the hybrids into high temperature elastic plateau regions, with moduli that vary over orders of magnitude as a function of composition and morphology. The first transition can be assigned to the glass transition of the PI domains while the second is ascribed to a temperature induced softening of the organic components within the PEO/hybrid domains. The results suggest that in the present nanostructured block copolymer/aluminosilicate hybrid materials composition and morphology provide a powerful tool to tailor mechanical property profiles.
A polystyrene‐block‐poly(2‐vinylpyridine) (PS‐b‐P2VP) micellar structure with a P2VP core containing 5 nm CdS nanoparticles (NPs) and a PS shell formed in toluene that is a good solvent for PS block undergoes the core‐shell inversion by excess addition of methanol that is a good solvent for P2VP block. It leads to the formation of micellar shell‐embedded CdS NPs in the methanol major phase. The spontaneous crystalline growth of Au NPs on the CdS surfaces positioned at micellar shells without a further reduction process is newly demonstrated. The nanostructure of Au/CdS/PS‐b‐P2VP hybrid NPs is confirmed by transmission electron microscopy, energy‐dispersive X‐ray, and UV‐Vis absorption.
