Influence of polycaprolactone-triol addition on thermal stability of soy protein isolate based films

The influence of polycaprolatone-triol (PCL-T) on the thermal degradation properties of soy protein isolate (SPI)-based films was studied by thermogravimetry and infrared spectroscopy under nitrogen atmosphere. The results showed that in the absence of PCL-T the thermal degradation began between 292 °C (pure SPI films) and ca. 264 °C (SPI/SDS films with more than 20% of SDS), and these values decreased further to the range 250-255 °C for SPI/SDS/PCL-T films. At the same time, the temperature of maximum degradation rate (T_max) decreased from 331 °C (pure SPI film) to ca. 280 °C for SPI/SDS/PCL-T films with 39% PCL-T content. This behavior was also confirmed by the activation energy (E) values associated with the thermal degradation process. Apparently, the low thermal stability of PCL-T as compared to other film constituents, along with its plasticizer characteristics, is responsible for the decreased stability of SPI/SDS/PCL-T films. The FTIR spectra of gas products evolved during the thermal degradation indicated the formation of OH, CO₂, NH₃ and other saturated compounds, suggesting that the reaction mechanism involved simultaneous scission of the C(O)-O polyester bonds and C-N, C(O)-NH, C(O)-NH₂ and -NH₂ bonds of the protein.     

Mechanical Properties of Uniaxially Cold-Drawn Films of Poly[(R)-3-hydroxybutyrate] and Its Copolymers

Uniaxially oriented films of poly[(R)-3-hydroxybutyrate] (P(3HB)) and two kind of copolymers, poly[(R)-3-hydroxybutyrate-co-8%-[R]-3-hydroxyvalerate] (P(3HB-co-8%-3HV)), and poly[(R)-3-hydroxybutyrate-co-[R]-5%-3-hydroxyhexanoate] (P(3HB-co-5%-3HH)), were prepared by cold-drawing from amorphous preforms at temperatures near to the respective glass transition temperatures. Melt-quenched films in a rubber state could be stretched reproducibly to a draw ratio of 500%∼1800%, and subsequent annealing under tension led to improvement of the tensile strength and Young's modulus. Two-step drawing resulted in further improvement of the mechanical properties. The mechanical properties remained unchanged after storing for 6 months at room temperature, suggesting that high orientation and crystallinity suppress the secondary crystallization.     

Mechanical properties of the novel organometallic polymer poly(ferrocenyldimethylsilane)

A study of the mechanical properties of poly(ferrocenyldimethylsilane) [Fe(η‐C₅H₄)₂SiMe₂]_n, 3 , a novel organometallic polymer, has been performed on thin films of this material. The Young's modulus and Poisson's ratio of film samples (15 × 1 × 1 mm) of 3 were measured in quasi‐static tension using a video extensometer. For 3 , the values of the Young's moduli (E) and Poisson's ratios (ν) were similar between axes in the plane and independent of the splicing direction used during sample preparation. The mean and standard deviation of the Young's modulus and Poisson's ratio were 0.78 ± 0.08 GPa and 0.37 ± 0.06 GPa, respectively. Thermomechanical analysis of 3 revealed a steady decrease of E from a room temperature value of approximately 0.70 GPa. Additionally, it was found that at 150 °C, 3 was unable to support even small stresses, consistent with the onset of a melt transition (ca. 135 °C). A mathematical model based on molecular geometry is developed to describe the results. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 2280–2288, 2005     

Synthesis of Low Dielectric Constant Polyetherimide Films

As the demand for downsizing in microelectronics is increasing, devices require material with lower dielectric constant accordingly. The dielectric constants for most polyimide (PI), including polyetherimide (PEI), films are ∼3.5. In this study, we modified the PEI by incorporating various monomers (fluorinated dianhydride 6FDA and phenylene ether diamines) to reduce the dielectric constant. The dielectric constants of synthesized PEIs decreased with increasing amounts of 6FDA content and phenylene ether units. The T_g decreased gradually with PEI containing longer phenylene ether units, but increased with the content of 6FDA. The thermal decomposition temperatures at 10% weight loss were ∼550 °C, indicating that these PEIs have high thermal stability. Both the tensile strength and the modulus decreased with the PEI containing longer phenylene ether units. The PEI synthesized with 40% 6FDA dianhydride and 1,4-bis(4-aminophenoxy)benzene (pBAB) diamine has the lowest dielectric constant of 2.78 at 1 MHz.     

Micellar and Mixed-Micellar Effects on Alkaline Hydrolysis of tris(1,10–phenanthroline)iron(II): Kinetic Exploration

The kinetics of alkaline hydrolysis of tris(1,10–phenanthroline)iron(II) has been studied in the presence of nonionic and mixed nonionic–ionic micellar media at 308 K. The effects of mixed-micellar environments of nonionic with ionic surfactants (C₁₂E₂₃/ATABs and C₁₂E₂₃/SDS) on the hydrolytic rate have been studied. The rate decreases monotonically with an increment of [C₁₂E₂₃]_T (total Brij 35 concentration) at constant [^?OH]₀ and has been discussed with the pseudo-phase micellar model. The rate also decreases with [C₁₂E₂₃]_T at a continuous addition of ionic surfactants (ATABs and SDS). The observed rate constant k_obs follows the empirical relation: k_obs = (k₀ + θK [C₁₂E₂₃]_T)/(1 + K [C₁₂E₂₃]_T) (where θ and K are empirical constants). The values of θ remain unaffected, whereas K decreases nonlinearly with [ATABs]_T in a mixed C₁₂E₂₃?ATAB micellar system. But the k_obs in a mixed C₁₂E₂₃–SDS micellar system is much lower than that of the C₁₂E₂₃–ATAB system and do not comply with any micellar kinetic models.     

Batch and semicontinuous emulsion copolymerization of vinyl acetate–butyl acrylate. II. Morphological and mechanical properties of copolymer latex films

Vinyl acetate/(VAc)-butyl acrylate/(BuA) copolymer latex films of various copolymer compositions were investigated for their morphological properties by electron microscopy techniques, and for their mechanical properties by dynamic mechanical spectroscopy (DMS), differential scanning calorimetry (DSC), and tensile strength measurements. Batch copolymer latex films showed domains of PBuA dispersed in PVAc matrix; the domain sizes were increased with increased BuA content. Semicontinuous latex films were homogeneous in composition. Glass transition temperatures T_g determined from DMS and DSC indicated the presence of two, low and high, transition temperatures for batch latex films. The two temperatures approached the individual homopolymers, with increased PBuA content up to 51 mol %. Semicontinuous latex films showed only one single T_g. Tensile properties of the batch copolymer films showed a higher ultimate tensile strength, higher Young's modulus, and lower percent elongation to break compared to semicontinuous latex films. These differences were found to reflect the effect of mode of monomer addition during the emulsion copolymerization process on the particle morphology, and confirmed earlier data on bulk, colloidal, and surface properties of the same copolymer latexes.     

Synthesis,morphology, and viscoelastic properties of cyanate ester/polyhedral oligomeric silsesquioxane nanocomposites

Cyanate ester (PT‐15, Lonza Corp) composites containing the inorganic–organic hybrid polyhedral oligomeric silsesquioxane (POSS) octaaminophenyl(T₈)POSS [ 1 ; (C₆H₄NH₂)₈(SiO_1.5)₈] were synthesized. These PT‐15/POSS‐ 1 composites (99/1, 97/3, and 95/5 w/w) were characterized by X‐ray diffraction (XRD), transmission election microscopy (TEM), dynamic mechanical thermal analysis, solvent extraction, and Fourier transform infrared. The glass‐transition temperatures (T_g's) of the composite with 1 wt % 1 increased sharply versus the neat PT‐15, but 3 and 5 wt % 1 in these cyanate ester composites depressed T_g. All the PT‐15/POSS composites exhibited higher storage modulus (E′) values (temperature > T_g) than the parent resin, but these values decreased from 1 to 5 wt % POSS. The loss factor peak intensities decreased and their widths broadened upon the incorporation of POSS. XRD, TEM, and IR data were all consistent with the molecular dispersion of 1 due to the chemical bonding of the octaamino POSS‐ 1 macromer into the continuous cyanate ester network phase. The amino groups of 1 reacted with cyanate ester functions at lower temperatures than those at which cyanate ester curing by cyclotrimerization occurred. In contrast to 1 , 3‐cyanopropylheptacyclopentyl(T₈)POSS [ 2 ; (C₅H₉)₇(SiO_1.5)₈CH₂CH₂CH₂CN] had low solubility in PT‐15 and did not react with the resin below or at the cure temperature. Thus, phase‐separated aggregates of 2 were found in samples containing 1–10 wt % 2 . Nevertheless, the T_g and E′ values (temperature > 285 °C) of these composites increased regularly with an increase in 2 . © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 3887–3898, 2005     

Effect of Plasticizer Type and Concentration on Dynamic Mechanical Properties of Sugar Palm Starch–Based Films

In the quest for biodegradable and environmentally friendly packaging materials, starch-based films have been considered as a potential alternative to address ecological problems that emerged from the use of nonbiodegradable petroleum-based plastics. Thus, this article presents a new biopolymer (sugar palm starch) for the preparation of biodegradable packaging films using the solution-casting technique. The effects of different plasticizer types (glycerol [G], sorbitol [S], and glycerol-sorbitol [GS] combination) with varying concentrations (0, 15, 30, and 45, w/w %) on the dynamic mechanical properties of sugar palm starch (SPS) films were evaluated. It was observed that the storage (E′) and loss modulus (E″) of the plasticized SPS films decrease as plasticizer concentration increases from 15 to 45%. S-plasticized films showed higher storage modulus (1000 MPa) than G (880 MPa) and GS (920 MPa) plasticized films, irrespective of plasticizer concentration.     

Segmented block copolyesters using click chemistry

Copper(I) catalyzed azide‐alkyne 1,3‐Huisgen cycloaddition reaction afforded the synthesis of triazole‐containing polyesters and segmented block copolyesters at moderate temperatures. Triazole‐containing homopolyesters exhibited significantly increased (～40 °C) glass transition temperatures (T_g) relative to high temperature, melt synthesis of polyesters with analogous structures. Quantitative synthesis of azido‐terminated poly(propylene glycol) (PPG) allowed for the preparation of segmented polyesters, which exhibited increased solubility and mechanical ductility relative to triazole‐containing homopolyesters. Differential scanning calorimetry demonstrated a soft segment (SS) T_g near ?60 °C for the segmented polyesters, consistent with microphase separation. Tensile testing revealed Young's moduli ranging from 7 to 133 MPa as a function of hard segment (HS) content, and stress at break values approached 10 MPa for 50 wt % HS segmented click polyesters. Dynamic mechanical analysis demonstrated an increased rubbery plateau modulus with increased HS content, and the T_g's of both the SS and HS did not vary with composition, confirming microphase separation. Atomic force microscopy also indicated microphase separated and semicrystalline morphologies for the segmented click polyesters. This is the first report detailing the preparation of segmented copolyesters using click chemistry for the formation of ductile membranes with excellent thermomechanical response. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Carbon nanocones/discs – a new type of filler to improve the thermal and mechanical properties of polymer films

The mechanical characteristics and thermal properties of composite films based on the thermally stable aromatic polyimide (PI) (PMDA‐ODA) and carbon nanocones/discs (CNC) were studied. The introduction of CNC to PMDA‐ODA leads to the substantial increase of film stiffness. The Young's modulus values of the composite films are somewhat higher than those of the previously characterized composite films of this PI filled with nanoclay, carbon nanofibers, and asbestos‐like hydrosilicate nanotubes. The introduction of CNC into PMDA‐ODA (concentrations of CNC were up to 15 vol%) does not cause any marked aggregation of nanoparticles. The presence of CNC in the PI matrix does not affect the glass transition temperature of the polymer but hinders chain mobility at temperatures above T_g. This behavior makes it possible to increase the working temperature range of the composite films containing more than 5 vol% of CNCs, up to the temperature of thermal decomposition. The introduction of CNC into PMDA‐ODA leads to dramatic (～12 orders of magnitude) increase of active electrical conductivity of the material. Copyright © 2011 John Wiley & Sons, Ltd.     

Relationships on the effect of water on glass transition temperature and young's modulus of nylon 6

The glass transition temperature T_g of nylon 6 decreases monotonically toward a finite value T_gl upon increase of the moisture content. The mechanism of this decrease entails the reversible replacement of intercaternary hydrogen bonds in the accessible regions of the polyamide. The limiting glass transition temperature T_gl is approached when the moisture content approaches W_l, which corresponds to the amount of water required for complete interaction with all accessible amide groups. Denoting with T_g0 the glass transition temperature of the dry polymer, the effect of water on T_g is represented by the equation, T_g = (ΔT_g)₀ exp{?[ln(ΔT_g)₀]W/_τW_l} + T_gl, where (ΔT_g)₀ = T_g0 ?T_gl, and τ = W(T_gl+1)/W_l. This equation appears to be generally applicable to hydrophilic polymers, since correspondingly calculated data are also in very good agreement with experimental data for polymers such as nylon 66, poly(vinyl alcohol), and polyN-vinylpyrrolidone. The effect of water of Young's modulus E of nylon 6 is represented by an analogous relationship, and the quantity In[(E?E_l)/(T_g?T_gl)] is a linear function of the moisture content.     

Measurement of size‐dependent glass transition temperature in electrospun polymer fibers using AFM nanomechanical testing

The glass transition temperature (T_g) of individual electrospun polymer polyvinyl alcohol fibers of varying diameter was measured using atomic force microscopy (AFM) based nanomechanical thermal analysis. Indentation and bending of individual electrospun fibers using AFM allowed the calculation of the elastic modulus of the polyvinyl alcohol (PVA) fibers across a range of different temperatures. The elastic modulus of electrospun PVA fibers was observed to decrease significantly when passing through T_g, which allowed accurate determination of T_g. The T_g of electrospun PVA fibers was shown to decrease for smaller fiber diameters especially for fiber diameters below 250 nm. This size‐dependent glass transition behavior of electrospun PVA fibers is indicated as being due to polymer chain confinement. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

A study on the glass transition behavior and morphology of semi-interpenetrating polymer networks

The epoxy resin/polyurethane semi-IPN was prepared and the glass transition behavior of the semi-IPN was discussed with DSC and DMA methods. The results show that the two glass transition temperatures (T_g) referring to epoxy resin and polyurethane respectively get closer. Between the two T_g there exists another T_g related to the interface between the two polymers. SEM indicates that this semi-IPN has a two-phase continuous structure which changes with different weight compositions. This is also proved by testing the Young's modulus. It is found that the IPN system has a cellular structure. Comparatively, the compatibility between the two polymers is the best when the weight ratio of EP/PU is 70/30. © 1996 John Wiley & Sons, Inc.     

Molecular orbital studies of polyethylene deformation

Young's modulus E for polyethylene in the chain direction is calculated with molecular orbital theory applied to n-alkanes C₃H₈ through n-C₁₃H₂₈ and analyzed with the cluster-difference method. Semiempirical CNDO, MNDO, and AM1 models and ab initio HF/STO-3G, HF/6-31G, HF/6-31G*, and MP2/6-31G* models are used. Cluster-difference results, when extrapolated to infinite chain length, give E in good agreement with moduli evaluated with molecular cluster or crystal orbital methods, provided minimal basis sets are employed. E decreases from 495 GPa (CNDO) to 336 GPa (MP2/6-31G*) as the level of theory is improved, consistent with established behaviors of the various models. Our calculations do not reproduce earlier molecular cluster or crystal orbital results, which gave E < 330 GPa. The most rigorous MP2/6-31G* model is known to overestimate force constants by ∼ 11%; the scaled modulus E = 299 GPa is in good accord with E = 306 GPa from recent calculations based on experimental vibration frequencies. © 1996 John Wiley & Sons, Inc.     

The effects of combined pressure–temperature on mechanical behavior of polypropylene

The effects of combined pressure and temperature on the mechanical behavior of polypropylene have been studied. Tests were conducted in tension and compression superimposed on various hydrostatic pressures up to 7 kbar at temperatures of 20, 50, and 75°C. The experimental data have been analyzed in view of molecular and continuum approaches. It has been observed that the Young's modulus and the yield strength in both tension and compression increased significantly with increasing pressure at all temperatures studied. However, the rate of increase of the Young's modulus undergoes abrupt change about the glass-transition pressure (P_g). The P_g is linearly dependent on the test temperature and the pressure coefficient of the T_g is estimated, from P_g versus temperature relations, to be about 18°C/kbar for the polypropylene samples of this study. Pressure dependence of the yield stress is described by a generalized Eyring theory incorporating pressure effects and two flow mechanisms, the α- and the β-relaxation processes. The theory predicts a bilinear dependence of the yield stress of polypropylene on hydrostatic pressure as observed in the tests. The paper also described a method of healing stress whitening in polypropylene by a combination of shear stress and hydrostatic pressure.     

Small Strain Mechanical Properties of Latex-Based Nanocomposite Films

A waterborne latex-based technique, in which functionalized laponite is attached to PS and acrylic latex particles, is used to prepare films containing up to 50 wt% laponite. At high laponite contents this leads to a cellular arrangement of the laponite-rich layers, concentrated at the latex particle interfaces. MDSC shows that a significant proportion of the organic matrix does not contribute to the glass transition. However, this “rigid” matrix fraction arises from intercalation of the laponite stacks, and cannot account for the large increases in global stiffness in the rubbery state (T > T_g) on laponite addition. The mechanical response for T > T_g is therefore discussed in terms of a four-phase structure, in which the intercalated laponite stacks embedded in a matrix with a relatively high rubbery modulus form a cellular structure, which is in turn embedded in a matrix whose modulus is closer to that of the bulk polymer. The importance of the cellular arrangement is underlined by the much lower rubbery modulus observed by DMA in specimens produced by deforming the original films in plane strain compression to produce oriented textures with relatively little connectivity between the laponite-rich layers.     

Thermal Analysis of Micro- and Nano-Lignocellulosic Reinforced Styrene Maleic Anhydride Composite Foams

The aim of this study was to measure the thermal properties of foamed nano/macro filler–reinforced styrene maleic anhydride (SMA) composites. SMA (66%) as a polymer matrix (10% maleic anhydride content) and various fillers including wood flour, starch, α-cellulose, microcrystalline cellulose and cellulose nanofibrils as reinforcing agents (30%) and lubricant (4%) were used to manufacture the composites in a twin-screw extruder. According to the thermogravimetric analysis (TGA) results, thermal degradation of all the foamed composites was found to be lower than that of SMA composites. The storage modulus values were negatively affected with a second time foaming (reprocessing [recycling] the initially processed composites a second time), as were loss modulus and T_g. As a result, second-time-foamed composite modulus values were lower than those of the foamed composites. According to the melt flow index (MFI) results, viscosity of the SMA was found to increase with the addition of fillers.     

Synthesis and properties of thermoplastic polyimides with ether and ketone moieties

A series of polyimides containing ether and ketone moieties were synthesized from 1,3‐bis(4‐fluorobenzoyl) benzene and several commercially available dianhydrides via a conventional two‐step polymerization. The inherent viscosities of Polyamide acids ranged from 0.46 to 0.73 dL/g. Thermal properties, mechanical properties, and thermalplasticity of the obtained polimide films were investigated by focusing on the chemical structures of their repeat units. These films were amorphous, flexible, and transparent. All films displayed low T_gs (184–225 °C) but also excellent thermal stability, the 5% weight loss temperature was up to 542 °C under nitrogen. The films showed outstanding mechanical properties with the modulus up to 3.0 GPa and the elongation at break in the range of 8–160%. The uniaxial stretching of PI‐a at high temperature was studied owing to its excellent flexibility. The PI‐a had an elongation at break up to 1600% at 245 °C and the uniaxially stretched film exhibited a much higher modulus (3.9 GPa) and strength (240 MPa) than undrawn film. The results indicated that PI‐a can potentially be used to prepare materials such as fiber, ultra‐thin film or ultra‐high modulus film. All the obtained films also demonstrated excellent thermoplasticity (drop of E′ at T_g > 10³) which made the polyimides more suitable for melt processing. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 2878–2884, 2010     

Properties and morphologies of UV‐cured epoxy acrylate blend films containing hyperbranched polyurethane acrylate/hyperbranched polyester

The properties and morphologies of UV‐cured epoxy acrylate (EB600) blend films containing hyperbranched polyurethane acrylate (HUA)/hyperbranched polyester (HPE) were investigated. A small amount of HUA added to EB600 improved both the tensile strength and elongation at break without damaging its storage modulus (E′). The highest tensile strength of 31.9 MPa and an elongation at break around two times that of cured pure EB600 were obtained for the EB600‐based film blended with 10% HUA. Its log E′ (MPa) value was measured to be 9.48, that is, about 98% of that of the cured EB600 film. The impact strength and critical stress intensity factor (K_1c) of the blends were investigated. A 10 wt % HUA content led to a K_1c value 1.75 times that of the neat EB600 resin, and the impact strength of the EB600/HPE blends increased from 0.84 to 0.95 kJ m^?1 with only 5 wt % HPE addition. The toughening effects of HUA and HPE on EB600 were demonstrated by scanning electron microscopy photographs of the fracture surfaces of films. Moreover, for the toughening mechanism of HPE to EB600, it was suggested that the HPE particles, as a second phase in the cured EB600 film, were deformed in a cold drawing, which was caused by the difference between the elastic moduli of HPE and EB600. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 3159–3170, 2005     

Electrical and mechanical properties of the zone-drawn polypyrrole films

The zone-drawing method (ZD) was applied to electrochemically synthesized polypyrrole films containing tosylate (PPy/TsO) and the mechanical and electrical properties of the resulting films were investigated. It was found that the electrical conductivity of the zone-drawn film reached 365 S cm⁻¹ in the drawing direction, which was 4.7 times that of the original film. The tensile properties of the zone-drawn film were improved and Young's modulus and strength at break increased to 4.32 GPa and 90.1 MPa from 0.53 GPa and 40.4 MPa of the as-synthesized film, respectively. The dynamic storage modulus (E) increased by the zone-drawing over a whole experimental temperature range and attained 7.0 GPa at room temperature and 4.0 GPa even at 200°C. © 1996 John Wiley & Sons, Inc.