Severe plastic deformation of amorphous alloys: II. Magnetic properties

The influence of severe plastic deformation in a Bridgman cell on the magnetic properties of amorphous alloys of metal-metalloid type, Ni₄₄Fe₂₉Co₁₅Si₂B₁₀, Fe₇₄Si₁₃B₉Nb₃Cu₁, Fe_57.5Ni₂₅B_17.5, Fe_49.5Ni₃₃B_17.5, and Fe₇₀Cr₁₅B₁₅, obtained by melt spinning, has been investigated. It is found that the saturation magnetization significantly changes (increases or decreases), depending on the number of ferromagnetic and antiferromagnetic components in the alloy. It is suggested that very high shear stress causes internal phase decomposition in the amorphous matrix into nanoscale regions, enriched or depleted with ferromagnetic components.     

Magnetic and mechanical properties of amorphous Fe-Y alloys

The magnetic and mechanical properties of amorphous Fe_100−xY_x alloys (20 ≤ x ≤ 60) fabricated by rapid quenching have been measured. The dependence of the density, Young's modulus and magnetic moment per Fe atom on x shows a break point between x = 30 and 40, accompanied by a drastic change in the X-ray diffraction pattern. The spontaneous volume magnetostriction as well as the forced volume magnetostriction are a maximum at x = 20 and decrease rapidly with increasing x. The variation of the magnetic and mechanical properties with x is explained by a change of the local atomic arrangement in the amorphous state, reflecting the structure of corresponding crystalline compounds.     

Structural mechanisms of plastic deformation of amorphous alloys containing crystalline nanoparticles

Patterns of plastic deformation of amorphous nanocrystalline composites, caused by the local action of an indenter on a thin electron microscopy foil, have been experimentally investigated for the first time in structural analysis. Classification of the observed types of interaction of shear bands with crystalline nanoparticles is performed. This classification is in good agreement with the theoretically predicted interaction mechanisms.     

Excess free volume and mechanical properties of amorphous alloys

Characteristics of the excess free volume in amorphous alloys quenched from a melt are investigated and analyzed. It is established by small-angle x-ray scattering that the application of intense hydrostatic pressure causes this volume to decrease. This decrease leads to an enhancement of a number of characteristics of the mechanical properties of amorphous alloys. Fiz. Tverd. Tela (St. Petersburg) 40, 85–89 (January 1998)     

Peculiar effects of plastic deformation by cold rolling on structure and mechanical properties of submicrocrystalline and titanium alloys

Using titanium VT1-0 and VT6 alloys as an example, peculiarities of the effect of plastic deformation by rolling at room temperature on the structure and mechanical properties of metallic materials in submicrocrytalline states are investigated. It is shown that this treatment can result in both hardening and softening of these alloys. It is established that variations in the behavior of their mechanical properties is controlled by the relation between structure parameters such as grain size, uniformity of their size distribution, and volume fraction of fine grains in the course of dicreasing dislocation density.     

Deformation behavior of amorphous Co-Fe-Cr-Si-B alloys in the initial stages of severe plastic deformation

The mechanical behavior and morphological features of the formation of strain relief in amorphous Co-Fe-Cr-Si-B alloys are studied in the initial stage of severe plastic deformation. Patterns of propagation in shear bands upon pressure torsion are revealed. The effects of surface etching and the decoration of shear bands are studied in the alloys. The causes behind these phenomena are discussed using a set of methods for structural investigation.     

Self-blocking of shear bands and the delocalization of plastic flows in amorphous alloys upon megaplastic deformation

Features of the formation of shear bands and nanocrystalline phases upon the megaplastic deformation of amorphous alloys based on iron, nickel, and titanium at room temperature in a Bridgman chamber are analyzed via transmission electron microscopy. It is shown that the transition from strongly localized to quasi-homogeneous plastic deformation occurs at a definite stage of the inhomogeneous plastic flow. Mechanisms based on the self-blocking of propagating shear bands by particles of the nanocrystalline phase that emerge due to a dissipative increase in the temperature along the front of shear bands are proposed for the delocalization of plastic flow.     

Structure and magnetic properties of iron-and cobalt-based amorphous alloys versus nanocrystallization conditions

The effect of the structural state of Fe₅Co₇₀Si₁₅B₁₀, Fe₆₀Co₂₀Si₅B₁₅, and Co_81.5Mo_9.5Zr₉ amorphous alloys on their magnetic properties is studied under different nanocrystallization conditions. A permanent magnetic field applied during thermomagnetic treatment is found to affect structuring in the amorphous alloys at the initial stage of devitrification. The fine structure of the devitrified amorphous alloys is shown to correlate with the field shifting the hysteresis loop. A mechanism accounting for a hysteresis loop shift in amorphous alloys is discussed.     

Magnetic properties of amorphous alloys

The magnetic properties of existing amorphous iron based materials, i.e., Fe--metalloid, Fe--early transition metals and Fe--rare earth alloys, are briefly discussed for some representative alloys. The spin orientation of amorphous Fe--metalloid alloys has been determined by the angular dependence of hyperfine interactions. It is shown that in iron--early transition metals ferromagnetic order is not long-ranged, but determined by magnetic clusters. The magnetic hyperfine field distributions of Fe-rich iron--early transition metals consist of a high and a low field tail. The magnetic structure has been investigated for two representative Fe--RE (RE = Er, Ce) amorphous alloys. For the first time, the magnetic coupling phenomenon in amorphous/crystalline multilayers has been discussed. This revised version was published online in August 2006 with corrections to the Cover Date.     

Basic patterns of the generation of high-angle grain boundaries and the physical and mechanical properties of FeNi alloys upon severe plastic deformation

The evolution of the structural parameters of deformation fragments and dynamically recrystallized grains in FeNi alloy are analyzed by means of transmission electron microscopy and back-scattered electron diffraction in a Bridgman camera upon severe plastic deformation with an increase in the number of full turns at a room temperature. It is found that the formation of a great many high-angle grain boundaries in the structure is associated with low-temperature dynamic recrystallization.     

Mechanical properties of Co-Si-B amorphous alloys

The ternary amorphous systems Co_xSi₅B_95?x with 7070Si _y B_30?y with 5<y<18 were studied for their mechanical properties at room temperature. Structure sensitive parameters as density, Young's modulus, micro-hardness and crystallization temperature were investigated as a function of Co and Si contents. The value of density increases with higher Co content but not linearly as for Co-B. Young's modulus, micro-hardness and crystallization temperature decrease with increasing Co concentration. The packing fractionη was calculated using 12-coordinated Goldschmidt atomic radii. It is shown that changes in the proportions of metalloids contents in the alloys have more significant influence on the atomic structure and therefore on the mechanical properties than changes of Co content. The maximum tensile elastic strain for the Co-Si-B system was estimated. Influence of magnetic moment on Young's modulus is discussed.     

Magnetic properties of amorphous NiP alloys

Magnetization, NMR and coercive force measurements were performed on amorphous Ni_1?cP_c alloys for concentration ranging between 0.15 and 0.25. The experimental results show that the magnetism is not of the same nature below and above some critical concentration c₀ which determines the concentration ranges: the first one (0.15 < c < 0.18) presents the characters of a weak homogeneous ferromagnetism, while inhomogeneities dominate the magnetic properties of the second one (0.18 < c < 0.25).     

Effects of plastic deformation on high-speed cutting in the properties of the swarf. I

Russian Physics Journal -     

Role of compositional changes on thermal,magnetic, and mechanical properties of Fe-P-C-based amorphous alloys

This work aimed to tune the comprehensive properties of Fe-P-C-based amorphous system through investigating the role of microalloying process on the crystallization behavior,glass forming ability(GFA),soft magnetic features,and mechanical properties.Considering minor addition of elements into the system,it was found that the simultaneous microalloying of Ni and Co leads to the highest GFA,which was due to the optimization of compositional heterogeneity and creation of near-eutectic composition.Moreover,the FeCoNiCuPC amorphous alloy exhibited the best anelastic/viscoplastic behavior under the nanoindentation test,which was owing to the intensified structural fluctuations in the system.However,the improved plasticity by the extra Cu addition comes at the expense of magnetic properties,so that the saturation magnetization of this alloying system is significantly decreased compared to the FeCoPC amorphous alloy with the highest soft magnetic properties.In total,the results indicated that a combination of added elemental constitutes,i.e.,Fe69Co5Ni5Cu1P13C7 composition,provides an optimized state for the comprehensive properties in the alloying system.     

Weak ferromagnetic properties of amorphous FeGe alloys

Magnetization measurements of amorphous FeGe alloys containing 20 and 30 at.% iron have been made under high field and high pressure. These alloys possess a weakly itinerant ferromagnetic character although large inhomogeneous effects are superposed.     

Low temperature properties of Pr amorphous alloys

Starting from the Fert and Campbell Hamiltonian and assuming a suitable η-distribution, the magnetization and the specific heat for Pr amorphous alloys are evaluated in the molecular field approximation with ferromagnetic interaction.Recent low-temperature experimental data on the specific heat of Pr amorphous alloys are reasonably explained.     

Superconducting properties of amorphous transition metal alloys

We have co-sputtered amorphous films of several Mo and W-based superconducting alloys. Measurements of T_c, ($\text{d}\text{H}{}_{\mathrm{c2}}\text{d}\text{T}$)_Tc and the normal state resistivity near T_c were made on a number of these alloys. Our results and other data from the literature are studied to examine the correlation between T_c and the dressed density of states at the Fermi level.     

Electronic transport properties of amorphous NiTi alloys

Measurements of electrical resistivity, magnetoresistance and Hall effect on amorphous Ni_100–x Ti _x alloys withx=39, 43, 60, 65, 70, and 76 are presented. The resistivity at 4.2 K is in the range 210 cm to 325 cm. The Hall coefficient turns out to be negative for low Ti contents and positive for high Ti contents with values around –6×10^–11 m³/As and +7×10^–11 m³/As, respectively. At low temperatures, the temperature and magnetic field dependences of the quantities measured are analysed and discussed in terms of weak localisation and electron-electron interaction effects.