氮气压强对PLD制备ZnO薄膜形貌及光电性能的影响

研究了氮气压强对脉冲激光沉积(PLD)法制备ZnO薄膜形貌及光电学性能的影响.结果表明,当氮气压强较低时,ZnO薄膜是由尺寸为50 nm的薄片组成;当氮气压强增加后,ZnO薄膜变成多孔状,并且组成ZnO薄膜的颗粒尺寸逐渐减小.在氮气压强为20 Pa以上时,所制备的ZnO薄膜的光致荧光(PL)光谱是由380 nm的带边发光峰和520 nm的缺陷发光峰组成;当氮气压强较低时(5 Pa和2 Pa),ZnO薄膜的PL光谱只有一个位于400 nm或41O nm处的发光峰.电学方而,2Pa和5 Pa氮气压强下制备的ZnO薄膜的电阻率约为氮气压强为20 Pa和50 Pa下制备样品的104和105倍.研究表明,当氮气压强较低时,Zn离子和O离子具有较大平均自由程和较大平均动能,因此易使N2离子化,可以使部分N离子掺入ZnO晶格中.当氮气压强较高时,Zn离子和O离子平均动能较小,不易使N2离子化,氮难于掺入ZnO晶格中.     

碱金属掺杂ZnO薄膜发光性能研究

采用固相反应法制备了不同比例的碱金属掺杂ZnO靶材,并利用磁控溅射法在Si(111)基片上制备不同温度下生长的c轴择优取向ZnO薄膜.通过XRD、AFM和荧光光谱(PL谱)研究了掺杂元素和掺杂比例对薄膜结构和发光特性的影响.结果表明,掺杂未改变ZnO的结构,薄膜具有很好的c轴择优取向.室温下用325 nm的氙灯作为激发光源得到不同样品的 PL 谱,分析表明,紫外发光峰来源于自由激子的复合辐射与带间跃迁,蓝绿发光峰与锌缺陷和氧缺陷有关.此外还探讨了紫外发光峰红移的可能机理.     

溶胶-凝胶法制备MgxZn1-xO及其特性

采用溶胶-凝胶法制备了不同组分(x=0.1～0.3)的MgxZn1-xO前驱体,并对它进行不同温度的热处理(550℃～1000℃).X射线衍射(XRD)结果表明,Mg0.1Zn0.9O具有和ZnO一样的衍射谱,为六方纤锌矿结构,而且随着热处理温度的升高,ZnO衍射峰的强度逐渐增强,半高宽不断减小;Mg元素掺杂浓度增大后,出现了MgO的峰位.扫描电子显微镜(SEM)显示Mg0.1Zn0.9O晶粒粒径分布较均匀;热处理温度升高,晶粒的尺寸不断变大.用室温荧光光谱(PL)分析了经过550～1000℃热处理获得的Mg0.1Zn0.9O粉末,结果发现除了550℃下处理的样品,其它都有紫外发射峰(350nm左右),而且随着热处理温度的升高紫外峰有明显的蓝移现象.     

钼酸锶基二元固溶体粉末的化学溶液沉积法制备及其发光特性研究

采用化学溶液沉积(CSD)技术,用廉价的无机盐(SrCO3、(NH4)6Mo7O24 · 4H2O)为主要初始原料、常见的有机试剂(丙三醇、冰乙酸和乙二醇甲醚)为溶剂,成功地制备了Ca0.7Sr0.3MoO4和Ba0.3Sr0.7MoO4两类具有白钨矿结构的二元固溶体粉末,并对两种粉体的结构、形貌、颗粒分布以及室温光致发光性能进行了测试.研究表明,两类钼酸锶基固溶体粉末都具有单一的四方相结构,且固溶特性良好,没有检测到明显的杂质峰;固溶体粉末的形貌和尺寸与粉体的成分密切相关,Ca0.7Sr0.3MoO4粉体的晶粒较小,为纳米量级,而Ba0.3Sr0.7MoO4粉体呈现明显的四棱锥外观,晶粒尺寸较大,为微米量级;两类粉末均呈现宽带发光特性,最大发光波长位于蓝绿光波段;Ca0.7Sr0.3MoO4粉体在室温下的发光强度较高,而Ba0.3Sr0.7MoO4粉体在同样条件下的发光强度极其微弱.     

衬底温度对磁控共溅射制备的Zn(O,S)薄膜结构和光电性能的影响

采用磁控共溅射沉积法,以氧化锌和硫化锌为靶材,在不同衬底温度下制备了Zn(O,S)薄膜.采用X射线衍射仪、原子力显微镜、紫外-可见-近红外分光光度计、霍尔测试仪和拉曼光谱测试仪对Zn(O,S)薄膜进行了结构和光电特性研究.结果表明:Zn(O,S)薄膜具有六方纤锌矿结构,属于二模混晶;在可见-近红外波段的吸收率小于5;;其为N型半导体,电学特性随衬底温度的变化而变化;衬底温度为200℃时制备的厚度为167 nm的Zn(O,S)薄膜的载流子浓度达到8.82×1019 cm-3,迁移率为19.3 cm2/V·s,表面呈金字塔结构.     

退火处理对ZnO薄膜发光特性的影响

用脉冲激光沉积法(PLD)在MgO(100)、α-Al2O3(0001)和MgAl2O4(111)衬底上沉积了ZnO薄膜,测量了它们的发射光谱,观察到430nm的蓝光发射,并研究了退火、衬底和激发波长对ZnO薄膜这一蓝光发射的影响.指出ZnO薄膜中430nm的蓝光发射是由锌填隙原子缺陷能级到价带顶能级间的跃迁以及电子从氧空位浅施主能级到价带顶能级间的跃迁两种机理共同作用的结果.在MgO衬底上沉积的ZnO薄膜在350nm光激发下蓝光发射峰最强.     

MgZnO/ZnO异质结构的发光性质研究

本文利用等离子体辅助分子束外延(P-MBE)技术在蓝宝石 (Al2O3) 衬底上生长了Mg0.12Zn0.88O(100nm)/ZnO (20nm) /Mg0.12Zn0.88O (40nm) 异质结构,测得样品的X射线衍射谱表明,在34.56°的位置出现很强的(002)方向衍射峰,其半高宽度为0.20°,比Mg0.12Zn0.88O合金薄膜的半高宽度0.15°明显展宽.通过光致发光谱研究了MgZnO/ZnO/MgZnO异质结构的光学性质,室温下测得在370nm(3.35eV)位置有很强的紫外发光,而在348nm (3.56eV)的位置处有一个较弱的发光,这两个峰分别被归结于来自ZnO层和MgZnO盖层的发光.室温下的吸收光谱中,在上述两个峰的位置附近分别存在很明显的吸收,指示了带边吸收来自于MgZnO和ZnO两种材料.通过变温发光谱研究了异质结构中载流子弛豫、复合的规律.随着温度增加,来自于ZnO层和MgZnO层的发光强度比增加,这归结为MgZnO/ZnO异质结构存在界面势垒所致.     

热退火对ZnO-SiO2复合薄膜的微结构及荧光特性的影响

采用脉冲激光沉积技术(PLD)在单晶Si衬底上制备了ZnO-SiO2复合薄膜.分别用SEM、XRD观察了样品在沉积态(300℃)及700℃和900℃下热退火后的形貌和结构.发现经700℃热处理后,样品中有第三相β-Zn2SiO4形成,经900℃热处理后的样品中硅锌矿型Zn2SiO4取代了β-Zn2SiO4成为第三相.研究了热退火处理前后样品的荧光特性变化,结果表明经700℃热处理后,荧光光谱与沉积态相比,紫外区域的发光强度有较大提高,可见光区域的宽带强度变弱;经900℃热处理后,紫外区域荧光强度与700℃处理相比略有减小,可见光发光带消失.     

不同缓冲层对ZnO薄膜的性能影响

用射频反应磁控溅射法在玻璃基底上分别以SnO2、SiO2和Al2O3为缓冲层制备ZnO薄膜.利用X射线衍射仪(XRD)、扫描电镜(SEM)、紫外-可见分光光度计和荧光分光光度计对薄膜的结构和光学性能进行了表征.XRD和SEM的分析结果表明,在SiO2和Al2O3缓冲层上生长的ZnO薄膜具有较好的c轴择优取向,薄膜表面光滑平整,薄膜的结晶质量得到改善;透射光谱表明所有样品在可见光范围内的平均透过率超过70;;通过对薄膜光致发光谱的分析,认为422 nm左右的紫峰来自于电子从晶粒边界的界面缺陷能级到价带的辐射跃迁;PL谱中蓝光和绿光的发光机制与薄膜中的本征缺陷有关.     

Al2O3衬底上生长ZnO薄膜的结构和光学特性

用脉冲激光沉积法在Al2O3(0001)衬底上沉积了ZnO薄膜.衬底温度分别为300℃、400℃、500℃、600℃和700℃.利用X射线衍射(XRD)和光致发光谱(PL)对薄膜的结构和光学性能进行研究.X射线衍射的结果表明在不同温度下生长的ZnO薄膜均具有高度c轴择优取向,衬底温度400℃时,膜的应力较小质量较高.ZnO薄膜有很强的紫外发光峰,紫外发光峰的强度与衬底温度密切相关,并发现当衬底温度从300℃增到400℃时,紫外发射峰出现6nm的蓝移.     

A review of measurement of thermophysical properties of silicon melt

Measurements of thermophysical properties of Si melt and supplementary study of X-ray scattering/diffraction by the authors' group were reviewed. The values obtained differed variously from those of literature. Density was 2–3% larger, surface tension 20–30% smaller, viscosity up to 40% larger, electrical conductivity 8% smaller, spectral emissivity more or less in good agreement with literature values, and thermal diffusivity a few percent larger. An anomalous density jump was found near the melting point. Surface tension and viscosity also showed anomaly. A strange time-dependent change of density was observed over 3 h after melting. X-ray analyses suggested a slight change in local atom ordering, but showed no sign of cluster formation. An addition of 0.1 at% gallium caused the density jump to disappear, while that of boron caused no change. An EXAFS study of the former melt indicated a strong interaction between Ga and Si atoms as if molecules of GaSi₃ existed. The implications of the measured properties are a possibility of soft-turbulence in an Si melt in a relatively large crucible, a more complicated manner of intake of oxygen depleted molten Si from the free surface region to underneath the growing crystal, and a relaxation of the melt after melting arising from trapped gas species.     

Effect of alumina on enthalpy of mixing of mixed alkali silicate glasses

The enthalpy of mixing of mixed alkali (Na₂O and K₂O) silicate glasses containing various concentrations of alumina was determined using an ion-exchange equilibrium method. For glasses with a constant alkali concentration, the enthalpy of mixing was found to become less negative with alumina addition. Consistent with our previous results on the enthalpy of mixing of alumina-free mixed alkali silicate glasses, the magnitude of enthalpy of mixing exhibited a good correlation with the molar volume mismatch of the corresponding two single alkali glasses as well as with the extent of conductivity mixed alkali effect, e.g. excess activation energy of conductivity, ΔE. The reduction of the magnitude of the enthalpy of mixing with alumina addition can be attributed to the reduction of non-bridging oxygen and ionic field strength. Combining the present results with results obtained earlier, the magnitude of the enthalpy of mixing for all mixed alkali (Na₂O and K₂O) silicate glasses with and without alumina was expressed by a simple function of a modified Tobolsky parameter, which takes into account the alkali concentration and the difference in cation-to-effective anion distances. The enthalpy of mixing data of the mixed alkali glasses was then compared with reported experimental data on the conductivity of mixed alkali aluminosilicate glasses. What appears to be conflicting experimental data can be understood in terms of the magnitude of the enthalpy of mixing and we can conclude that the mixed alkali effect is closely correlated with the negative enthalpy of mixing.     

Mesomorphism Dependence on the Position of Substitution of a Pair of Esters

A novel homologous series of ethylene derivatives of thermotropic liquid crystals has been synthesized. The methoxy to octyloxy derivatives are nematogenic, the decyloxy to tetradecyloxy derivatives are smectogenic, in addition to nematogenic, and the hexadecyloxy homologue is smectogenic only. All the members of the series are enantiotropically mesogenic. Thermotropic behavior was determined by an optical polarizing microscope equipped with a heating stage and Differential Scanning Calorimetry (DSC) study. Analytical and spectral data confirm the molecular structures of homologues (infrared, nuclear magnetic resonance, mass spectra, X-ray, and DSC data). Textures of the nematic phase are threaded or Schlieren and that of smectic phase are focal conic fan-shaped of smectic A or C. Transition curves of the phase diagram behave in a normal manner except one or two deviations from the normal trend. The mesophase range (Sm+N) varies from 3°C to 44°C. The average thermal stability for smectic is 93°C and that for nematic 117.4°C. The LC behavior of the novel series is compared with a structurally similar known series.     

原位氮化法制备TiN纳米粉体

用溶胶凝胶法合成的纳米TiO2粉体作为原料,将该粉体在氨气中进行原位氮化制备了TiN纳米粉体.用XRD,TEM,化学分析等手段对合成的TiN纳米粉体的物相组成、形貌、成分进行了分析.实验分析表明:在1000℃和1100℃下分别氮化5h,可以制备粒径大约为40nm和80nm的TiN粉体,其TiN的含量分别为95.40;和98.37;;而在1000℃条件下氮化时间减少到2h时,TiN的含量仅为58.36;.氮化温度和氮化时间是合成纳米TiN的重要因素,提高合成温度和延长氮化时间均可形成纯度较高的TiN纳米粉体,但延长氮化时间更有利于获得粒径小的氮化钛粉体.     

立方晶系晶体本征铁弹相变序参量的选取

在本征铁弹相变的软模理论的基础上,依据弹性本构关系和居里原理,给出了立方晶系晶体所有可能的自发应变的种类,研究了立方晶系晶体本征铁弹相变序参量的选取问题.以Th群和Oh群为例,阐明了不同类的序参量导致晶体对称性变化相同的的原因,提出了该情况下序参量选取的“就少不就多”的原则.得到了发生本征铁弹相变时所有可能的序参量及晶体的对称性的变化.     

On the influence of structural features of DNA on the possibility of metabolic transfer of electrons

Abstract

A fragment of a DNA molecule is considered as one of the channels of metabolic electron transfer. The heterogeneity of the complementary chains is effectively taken into account. This made it possible to find the speed of the electron injected into the DNA conduction band and the current density that it creates. Estimates of electron mobility in nucleic acid chains are made. They were an order of magnitude smaller than that of typical semiconductors. For the specific conductivity of nucleic acid chains, estimates provide a conductivity of one to two orders of magnitude lower than in graphite.     

Features of transformations in REE-containing systems of nitrate precursors in preparatory processes of formation of multifunctional oxide materials

Abstract

The complex study provides a reliable idea of ??the trends in the joint behavior of structural components in the water-salt systems of nitrate precursors of REE, alkaline, alkaline earth metals in the preparatory stages of the processes of forming multicomponent oxide polyfunctional materials on their basis with thermal activation. Stages of such transformations are revealed; The regularities of complex and phase formation in systems and factors influencing them are determined; A number of physicochemical properties of the intermediate phases formed - coordination lanthanides nitrates: their composition, types of compounds, atomic-crystalline structure, regularities of transformations during heat treatment were studied.     

Growth and characterization of semicarbazone of cyclohexanone

A new organic single crystal of semicarbazone of cyclohexanone (SCCH) has been synthesized and grown as a bulk single crystal by low temperature solution growth technique for the first time in the literature. The grown crystal has been confirmed by X‐ray diffraction and proton nuclear magnetic resonance spectral analyses and also characterized by FT‐ir and FT‐Raman studies. Thermal properties of the grown crystals were studied by thermogravimetric and differential thermal analyses. Optical transmittance was studied by ultraviolet‐visible spectrum and the second harmonic generation property was tested by using Q switched Nd: YAG laser as a source. (© 2006 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Influence of density of states on optical properties of GaSe thin film

A systematic investigation on the effect of substrate temperature on the structure, optical absorption and density of states of vacuum evaporated gallium monoselenide (GaSe) thin films is reported. The X‐ray diffraction analysis shows an occurrence of amorphous to polycrystalline transformation in the films deposited at higher‐temperature substrates (573K). The compositional analysis is made with Auger Electron Spectroscopy (AES). The thickness of the film (175nm) is measured by a multiple beam interferometery. Optical characteristics of the GaSe sample have been analyzed using spectrophotometer in the photon energy range of 1.0 ‐ 4 eV. The absorption mechanism has been recognized and the allowed indirect as well as forbidden direct transitions have been found. As‐deposited films show two indirect and allowed transitions due to spin‐orbit splitting of the valence band, as reported here for the first time. Low field conduction have enabled us to determine the density of states in amorphous and poly‐GaSe films. The amorphous and polycrystalline GaSe thin films have localized states density values of N (E_F) = 1.686 × 10¹⁷ cm^‐3 eV^‐1 and 1.257 × 10¹⁵ cm^‐3 eV^‐1 respectively. The experimental results are interpreted in terms of variations in the density of localized states due to progressive decrease of the unsaturated bonds during deposition. (© 2004 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

电子显微分析在表征纳米晶体化学组分中的应用

纳米材料的化学组分及含量影响其光、电、声、热、磁等物理性能,电子显微分析是表征纳米晶体化学组分的重要方法之一.本文综述了X-射线能谱(EDS)、X-射线波谱(WDS)、电子能量损失谱(EELS)和选区电子衍射(SAED)等现代电子显微分析技术在表征纳米晶体化学组分、形貌、尺寸和结构等方面的应用及其研究进展,并比较了这些分析方法存在的差异,提出了其应用中存在的不足及今后的研发方向.