Photochemical vapor generation of carbonyl for ultrasensitive atomic fluorescence spectrometric determination of cobalt

UV photochemical vapor generation (photo-CVG) as sample introduction was first adapted for determination of ultratrace cobalt by atomic fluorescence spectrometry (AFS). Cobalt volatile species can be generated when the buffer system of formic acid and formate containing Co (II) is exposed to UV radiation. The generated gaseous products were separated from liquid phase within a gas–liquid separator and then transported to AFS for determination of cobalt. Factors affecting the efficiency of photo-CVG were investigated in detail, including type and concentration of low molecular weight (LMW) organic acid, buffer system, UV irradiation time, reaction temperature, carrier gas flow rate and hydrogen flow rate. With 4% (v/v) HCOOH and 0.4 mol L^{− 1} HCOONa buffer solution, 150 s irradiation time and 15 W low pressure mercury lamp, a generation efficiency of 23–25% was achieved. A limit of detection (LOD) of 0.08 ng mL^{− 1} without any pre-concentration procedure and a precision of 2.2% (RSD, n = 11) at 20 ng mL^{− 1} were obtained under the optimized conditions. The proposed method was successfully applied in the analysis of several simple matrix real water samples.     

Continuous flow electrolytic cold vapor generation atomic fluorescence spectrometric determination of Hg in water samples

The determination of trace concentrations of Hg in water samples by the use of electrolytic cold vapor generation (ECVG) system and AFS was studied. Several buffer solutions were used and the detection limits with these systems were found to be by a factor of 1–2 lower than in the conventional electrolytic cold vapor generation system. Comparing with the traditional inorganic acid, phosphate buffer solution (PBS) increased the signal intensity of Hg vapor from electrolytic generation on Pt cathode and reduced the impact of cathode erosion on the stability of signal intensity. Moreover, buffer solution has better interference tolerance. The effects of the electrolytic conditions and interference ions on the ECVG have been studied. Under optimized conditions and with PBS as catholyte the detection limit for Hg was found to be 0.27 ng L⁻¹. The relative standard deviation was 2.8% for 11 consecutive measurements of 1 μg L⁻¹ Hg. This method has been applied in the determination of inorganic Hg in Yangtze River water.     

UV photochemical vapor generation-atomic fluorescence spectrometric determination of conventional hydride generation elements

A systematic investigation of UV photochemical vapor generation (photo-CVG) and its potential application for seven typical hydride-forming elements (As, Sb, Bi, Te, Sn, Pb and Cd) when combined with atomic fluorescence spectrometry (AFS) detection is presented. These analyte ions were converted to volatile species following UV irradiation of their aqueous solution to which low molecular weight organic acids (such as formic, acetic or propionic acid) had been added, and introduced to an atomic fluorescence spectrometer for subsequent analytical measurements. The experimental conditions for photo-CVG and the interferences arising from concomitant elements were carefully investigated. Limits of detection as low as 0.08, 0.1, 0.2 and 0.5 ng mL^− 1 were obtained for Te, Bi, Sb and As, respectively, comparable to those by hydride generation-AFS. The RSDs obtained with the proposed method for these elements were better than 5% at 50 ng mL^− 1. It is noteworthy that the presence of TiO₂ nanoparticles combined with UV irradiation remarkably enhances the CVG efficiencies of Se(VI) and Te(VI), which cannot form hydrides with KBH₄/NaBH₄. Moreover, photo-CVG has a greater tolerance toward interferences arising from transition elements than hydride generation, and this facilitates its application to the analysis of complicated sample matrices.     

微波辅助氯化物发生-原子荧光光谱法测定水样中的痕量砷

通过微波辅助提高砷的氯化物发生效率,并将其作为原子荧光光谱分析法测定砷的进样技术。在优化的实验条件下,本法对As(III)的检出限(3σ)为1μg L-1,相对标准偏差为3.5%。该法优点还在于对常见过渡金属有较强的抗干扰能力。应用该法测定了自来水及河水中的As(III),加标回收率为100%～115%。     

UV-induced carbonyl generation with formic acid for sensitive determination of nickel by atomic fluorescence spectrometry

UV-induced carbonyl generation with formic acid is used for gaseous sample introduction into an atomic fluorescence spectrometer for the determination of ultra-trace nickel. Compared with conventional carbonyl generation, no toxic gas CO is involved in this work, and volatile Ni(CO)₄ is generated with a single reagent formic acid under the irradiation of UV light (253.7 nm, 15 W). The reaction conditions, including reaction medium, UV irradiation time and reaction temperature, are optimized for the best signal. Under the optimized conditions, a limit of detection of 10 ng L⁻¹ for nickel is obtained without any analyte-pre-concentration, which is comparable to that using in situ trapping technique. Interferences from common transition metal ions, noble metal ions and mineral acids are also investigated. The proposed method is applied to the analysis of three certified reference materials and two organic acid samples for trace nickel, with analytical results in good agreement with certified values or those obtained by electrothermal atomic absorption spectrometry. This is a simple, fairly green and highly sensitive method for ultra-trace nickel determination.     

Photo-induced cold vapor generation with low molecular weight alcohol, aldehyde, or carboxylic acid for atomic fluorescence spectrometric determination of mercury

With UV irradiation, Hg²⁺ in aqueous solution can be converted into Hg⁰ cold vapor by low molecular weight alcohols, aldehydes, or carboxylic acids, e.g., methanol, formaldehyde, acetaldehyde, glycol, 1,2-propanediol, glycerol, acetic acid, oxalic acid, or malonic acid. It was found that the presence of nano-TiO₂ more or less improved the efficiency of the photo-induced chemical/cold vapor generation (photo-CVG) with most of the organic reductants. The nano-TiO₂-enhanced photo-CVG systems can be coupled to various analytical atomic spectrometric techniques for the determination of ultratrace mercury. In this work, we evaluated the application of this method to the atomic fluorescence spectrometric (AFS) determination of mercury in cold vapor mode. Under the optimized experimental conditions, the instrumental limits of detection (based on three times the standard deviation of 11 measurements of a blank solution) were around 0.02–0.04 μg L⁻¹, with linear dynamic ranges up to 15 μg L⁻¹. The interference of transition metals and the mechanism of the photo-CVG are briefly discussed. Real sample analysis using the photo-CVG-AFS method revealed that it was promising for water and geological analysis of ultralow levels of mercury. Image of the photo-CVG instrumentation showing the photoreactor inside the water cooling unit     

UV light-emitting-diode photochemical mercury vapor generation for atomic fluorescence spectrometry

A new, miniaturized and low power consumption photochemical vapor generation (PVG) technique utilizing an ultraviolet light-emitting diode (UV-LED) lamp is described, and further validated via the determination of trace mercury. In the presence of formic acid, the mercury cold vapor is favourably generated from Hg(2+) solutions by UV-LED irradiation, and then rapidly transported to an atomic fluorescence spectrometer for detection. Optimum conditions for PVG and interferences from concomitant elements were investigated in detail. Under optimum conditions, a limit of detection (LOD) of 0.01 μg L(-1) was obtained, and the precision was better than 3.2% (n = 11, RSD) at 1 μg L(-1) Hg(2+). No obvious interferences from any common ions were evident. The methodology was successfully applied to the determination of mercury in National Research Council Canada DORM-3 fish muscle tissue and several water samples.     

A hydride generation atomic fluorescence spectrometric procedure for selenium determination after flow injection on-line co-precipitate preconcentration

A flow injection (FI) on-line preconcentration procedure for ultra-trace inorganic selenium was developed with detection by atomic fluorescence spectrometry. Selenium (IV) is co-precipitated with lanthanum hydroxide and collected on a PTFE beads packed column, the precipitate is afterwards dissolved with hydrochloric acid followed by hydride generation with reduction by tetrahydroborate. A thorough scrutiny was made for chemical variables and FI parameters. With a sampling volume of 3.4 ml, quantitative retention of selenium (IV) was obtained, along with an enrichment factor of 11 and a sampling frequency of 38 h^− 1. The detection limit, defined as 3 times the blank standard deviation (3σ), was 5 ng l^− 1. The precision was characterized by a RSD value of 1.2% (at the 0.5 μg l^− 1 level, n = 11). The enrichment factor was further enhanced to 20 along with a detection limit of 3 ng l^− 1, with a sample loading volume of 6.8 ml. The procedure was validated with certified reference materials and biological samples. It was also applied to the speciation of inorganic selenium in surface waters.     

Multipumping flow system for improving hydride generation atomic fluorescence spectrometric determinations

The advantages of using membrane micropumps rather than peristaltic pumps to introduce both sample and reagent solutions for hydride generation atomic fluorescence spectrometry are discussed. Arsenic was used as a test analyte to check the performance of the proposed manifold. Sample and reagent consumption was reduced 8–9 fold compared with continuous mode measurements made with peristaltic pumps, with no deterioration in sensitivity. The calibration graph was linear in the 0.05 to 2.5 μg l^− 1 As range using peak area as the analytical signal and maximum gain in the detector setting. A limit of detection (3σ) of 0.02 μg l^− 1 and relative standard deviation values close to 2% for 10 independent measurements of a 1 μg l^− 1 As solution were obtained. The sampling frequency increased from 45 to 102 h^− 1 with the subsequent saving in carrier gas used and reduction in wastes generated. The instrumental modification, which could be used for other elements currently determined by atomic fluorescence spectrometry, will permit hydride generators of more reduced dimensions to be constructed.     

Hydride generation atomic fluorescence spectrometric determination of ultratraces of selenium and tellurium in cow milk

A sensitive procedure has been developed for selenium and tellurium determination in milk by hydride generation atomic fluorescence spectrometry (HG-AFS) after microwave-assisted sample digestion. The method provides sensitivity values of 1591 and 997 fluorescence units ng⁻¹ ml⁻¹ with detection limits of 0.005 and 0.015 ng ml⁻¹ for Se and Te, respectively. The application of the developed methodology to the analysis of cow milk samples of the Spanish market evidenced the presence of concentration ranges from 11.1 to 26.0 ng ml⁻¹ for Se, and from 1.04 to 9.7 ng ml⁻¹ for Te having found a good comparability with data obtained after dry-ashing of samples.     

Flow injection-chemical vapor generation atomic fluorescence spectrometry hyphenated system for organic mercury determination: A step forward

Monomethylmercury and ethylmercury were determined on line using flow injection-chemical vapor generation atomic fluorescence spectrometry without neither requiring a pre-treatment with chemical oxidants, nor UV/MW additional post column interface, nor organic solvents, nor complexing agents, such as cysteine. Inorganic mercury, monomethylmercury and ethylmercury were detected by atomic fluorescence spectrometry in an Ar/H₂ miniaturized flame after sodium borohydride reduction to Hg⁰, monomethylmercury hydride and ethylmercury hydride, respectively. The effect of mercury complexing agent such as cysteine, ethylendiaminotetracetic acid and HCl with respect to water and Ar/H₂ microflame was investigated.The behavior of inorganic mercury, monomethylmercury and ethylmercury and their cysteine-complexes was also studied by continuous flow-chemical vapor generation atomic fluorescence spectrometry in order to characterize the reduction reaction with tetrahydroborate. When complexed with cysteine, inorganic mercury, monomethylmercury and ethylmercury cannot be separately quantified varying tetrahydroborate concentration due to a lack of selectivity, and their speciation requires a pre-separation stage (e.g. a chromatographic separation). If not complexed with cysteine, monomethylmercury and ethylmercury cannot be separated, as well, but their sum can be quantified separately with respect to inorganic mercury choosing a suitable concentration of tetrahydroborate (e.g. 10^? 5 mol L^? 1), thus allowing the organic/inorganic mercury speciation.The detection limits of the flow injection-chemical vapor generation atomic fluorescence spectrometry method were about 45 nmol L^? 1 (as mercury) for all the species considered, a relative standard deviation ranging between 1.8 and 2.9% and a linear dynamic range between 0.1 and 5 μmol L^? 1 were obtained. Recoveries of monomethylmercury and ethylmercury with respect to inorganic mercury were never less than 91%. Flow injection-chemical vapor generation atomic fluorescence spectrometry method was validated by analyzing the TORT-1 certificate reference material, which contains only monomethylmercury, and obtaining 83 ± 5% of monomethylmercury recovered, respectively. This method was also applied to the determination of monomethylmercury in saliva samples.     

Flame-in-gas-shield miniature flame hydride atomizers for ultra trace element determination by chemical vapor generation atomic fluorescence spectrometry

Flame-in-gas shield miniature hydride atomizers (FIGS) have been investigated and evaluated in view of their alternative use to miniature diffusion flame hydride atomizer (MDF) to determination of hydride forming elements by atomic fluorescence spectrometry (AFS). Chemical vapour generation (CVG) by aqueous phase derivatization by NaBH₄ in a continuous flow generator (CF) was employed for the generation of volatile hydrides of As, Sb, Bi, Se, Te and Sn. A dispersive AFS apparatus using electrodeless discharge lamps (EDL) as the excitation sources has been employed for both spectra acquisition and analytical determinations. The characteristics of FIGS in terms of background emission spectra, most intense AF spectral lines and limits of detection were compared with those of most popular MDF. FIGS presents a lower background emission with respect to MDF, allowing also the control of the molecular fluorescence of OH radicals in the determination of bismuth. Limits of detection for FIGS compare very well with to those obtained by MDF giving improvement factor of 5.5, 4.4, 3.6, 3.6, 0.7 an 0.5 for Bi, As, Se, Son, Te and Sb. Accuracy of FIGS has proven by determination of arsenic and antimony in seawater (NASS-5) and river water (SRLS-4) certified reference materials and bismuth in unalloyed copper (CuV 398, CuVI 399) standard reference materials by dispersive CVG-AFS.     

Liquid chromatographic--cold vapour atomic fluorescence spectrometric determination of mercury species

Solvent extraction, sonication, and microwave-assisted extractions in the presence of extraction agents (thioacetic acid, citric acid, cysteine, 2-mercaptoethanol, HCl + NaCl, etc.) were tested for the isolation of mercury species. A mixture of 6 M HCl and 0.1 M NaCl was selected as the most suitable extraction agent. The extraction efficiency was about 10% higher and the RSD below 3.3% when microwave-assisted extraction was applied instead of sonication. The liquid chromatography-cold vapour atomic fluorescence spectrometry (LC/CV-AFS) method was optimised and used for separation and determination of inorganic mercury cations and alkylated and arylated mercury species. Isocratic elution at a flow rate of 0.15 mL/min (with a mobile phase containing 0.05% 2-mercaptoethanol (pH = 5) and 7% methanol and with a stepwise increase of methanol content up to 100% MeOH in the 15th min) was used for separation of mercury species on a Hypersil BDS C18 RP column. The limits of detection of the LC/CV-AFS system were estimated as 0.2 microg/L (3%) for MeHg+, 0.07 microg/L (5.3%) for inorganic Hg, 0.06 microg/L (3.4%) for PhHg+, and 0.12 microg/L (4.4%) for EtHg with the corresponding RSDs at 5 microg/L (n = 10) given in parentheses. The concentrations (2-10 mg/kg fresh weight) of total mercury and methylmercury (90-99% of the total mercury) in selected fish obtained by HPLC/CV-AFS were in good agreement (absolute deviations 0.05 mg/kg) but more precise (RSDs <5.4% at 5 mg/L, n = 10) than those determined by GC coupled to an electron capture detector. The RSDs (3.1-8.2% and 4.1-9.0%) of the overall analytical procedure for the determination of total mercury (AMA 254) and methylmercury (HPLC/CV-AFS) were determined for intra-day and inter-day assays, respectively.     

Determination of mercury and methylmercury in seafood by ion chromatography using photo-induced chemical vapor generation atomic fluorescence spectrometric detection

A novel method based on photo-induced chemical vapor generation (CVG) as interface to on-line coupled Hg-cysteine ion chromatograpy (IC) with atomic fluorescence spectrometry (AFS) was developed for rapid determination of methylmercury (MHg) in seafood. Separation of inorganic mercury (Hg²⁺) and methylmercury(CH₃Hg⁺) was accomplished on a Hamilton PRP X-200 polymer-based exchange column with a mobile of 3% acetonitrile, 1% (w/w) L-cysteine and 20 mmol L^{− 1} pyridine and 160 mmol L^{− 1} formic acid, at pH 2.4 within 7 min. Once separated, both species are reduced by formic acid in mobile phase under UV radiation to convert Hg⁰ on-line, which is subsequently swept (by argon carrier gas) into an atomic fluorescence spectrometry (AFS) for measurement. Under the optimized experiment conditions, the detection limits (as Hg), based on three times the standard deviation of a standard solution, were found to be 0.1 ng mL^{− 1} for mercury and 0.08 ng mL^{− 1} for methylmercury, with an injection volume of 100 μL. The developed method was validated by determination of certified reference material DORM-2 and was further applied in determination of seafood samples.     

Improvements in the non-dispersive atomic fluorescence spectrometric determination of arsenic and antimony by a hydride generation technique

A sodium borohydride reduction, with subsequent atomization in a small argon—hydrogen—entrained air flame has been developed for the determination of arsenic and antimony by non-dispersive atomic fluorescence spectrometry. The proposed method increases the signal level and decreases the noise level in the system. The detection limits for arsenic and antimony are 0.05 ng and 0.1 ng, respectively. The analytical working curves are linear over about four decades of concentration from the detection limits. The consumption rates of hydrogen and argon are comparatively low, while the speed of hydride evolution is improved; a peak measurement requires less than 40 s. The technique has been applied to the determination of arsenic in steel samples.     

Direct determination of mercury in white vinegar by matrix assisted photochemical vapor generation atomic fluorescence spectrometry detection

This paper proposes the use of photochemical vapor generation with acetic acid as sample introduction for the direct determination of ultra-trace mercury in white vinegars by atomic fluorescence spectrometry. Under ultraviolet irradiation, the sample matrix (acetic acid) can reduce mercury ion to atomic mercury Hg⁰, which is swept by argon gas into an atomic fluorescence spectrometer for subsequent analytical measurements. The effects of several factors such as the concentration of acetic acid, irradiation time, the flow rate of the carrier gas and matrix effects were discussed and optimized to give detection limits of 0.08 ng mL⁻¹ for mercury. Using the experimental conditions established during the optimization (3% v/v acetic acid, 30 s irradiation time and 20 W mercury lamp), the precision levels, expressed as relative standard deviation, were 4.6% (one day) and 7.8% (inter-day) for mercury (n = 9). Addition/recovery tests for evaluation of the accuracy were in the range of 92–98% for mercury. The method was also validated by analysis of vinegar samples without detectable amount of Hg spiked with aqueous standard reference materials (GBW(E) 080392 and GBW(E) 080393). The results were also compared with those obtained by acid digestion procedure and determination of mercury by ICP-MS. There was no significant difference between the results obtained by the two methods based on a t-test (at 95% confidence level).     

光化学蒸气发生方法用于水样中汞的可视化检测

汞与碘化亚铜的络合显色反应已被广泛应用于汞的可视化检测。然而,样品中高盐、强酸或强碱性的复杂基质对碘化亚铜及络合物的稳定性影响较大,可视化测定受到了严重干扰。光化学蒸气发生是一种绿色、高效的样品引入技术,可实现待测离子与样品基质的有效分离,并且在蒸气发生过程中不需要添加有毒、强还原性试剂。因此,本实验建立了一种光化学蒸气发生和自制碘化亚铜试纸结合用于可视化检测水样中汞的方法,对反应时间、低分子量有机酸浓度等条件进行了考察。在最优的条件下实现了1 ng·mL^-1～1μg·mL^-1浓度范围内水样中汞的可视化半定量分析,并通过原子荧光光谱法对分析结果进行了验证。     

Comparison of pre-reducing agents for antimony determination by hydride generation atomic fluorescence spectrometry

A systematic study of antimony reduction prior to its determination by hydride generation atomic fluorescence spectrometry (HG-AFS) was carried out. The efficiency of l-cysteine, potassium iodide and potassium iodide/ascorbic acid was studied for this purpose. The hydride generation step was optimised in the presence of those pre-reductors. From the results, l-cysteine was found to be the most suitable pre-reducing agent. Methodology was validated, obtaining detection limits lower than 90 ng l⁻¹ and repeatability and reproducibility better than 3% R.S.D. and 5% R.S.D., respectively, in all cases. In order to evaluate the methodology developed and the influence of the matrix, recovery from waters from different sources was tested by HG-AFS and also by inductively coupled plasma mass spectrometry (ICP-MS). Accuracy was assessed by analysing three water reference materials at different antimony concentration levels. The high sensitivity of the developed methodology enables it to be applied for monitoring drinking waters according to the maximum admissible concentration of antimony established by the EU Directives.     

Flow injection-hydride generation atomic absorption spectrometric determination of selenium, arsenic and bismuth

A simple and robust flow injection system which permits low sample and reagent consumption is described for rapid and reliable hydride generation atomic absorption spectrometric determination of selenium, arsenic and bismuth. The system, which composed of one peristaltic pump and one four channel solenoid valve, used water as the carrier streams for both sample and NaBH₄ solution. Rapid off-line pre-reduction of the analytes was achieved by using hydroxylamine hydrochloride for selenium and a mixture of potassium iodide and ascorbic acid for arsenic and bismuth. Transition metal interference was eliminated with the addition of thiourea and EDTA into the NaBH₄ solution and significant sensitivity enhancement was observed for selenium in the presence of thiourea in the reductant solution. Under optimised conditions, the method achieved detection limits of 0.2 ng mL⁻¹ for Se, 0.5 ng mL⁻¹ for As and 0.3 ng mL⁻¹ for Bi. The method was very reproducible, achieving relative standard deviations of 6.3% for Se, 3.6% for As and 4.7% for Bi, and has a sample throughput of 360 h⁻¹. Successful application of the method to the quantification of selenium, arsenic and bismuth in a certified reference river sediment sample is reported.     

Inductively-coupled plasma atomic emission spectrometric determination of boron based on generation of methyl borate

Boron is converted to methyl borate, distilled and condensed, and selectively volatilized at 50°C into the plasma without interference from methanol, which quenches the plasma. The 3σ detection limit is 40 ng ml^?1 boron, the calibration graph is linear up to 10 μg ml^?1 and the r.s.d. 3.0% for 2.0 μg ml^?1 (n = 10). Boron is determined in plant-tissue and steel standards.