改进水热法合成SAPO-11及其酸性和异构化活性

在含异丙醇的体系中,采用程序升温水热法合成了SAPO-11分子筛,并通过X射线衍射、扫描电镜、低温氮物理吸附、氨程序升温脱附、吡啶吸附红外光谱和29Si固体核磁共振等手段进行了表征.结果表明,与常规水热合成法相比,该方法合成的SAPO-11结晶度高,晶粒小,微孔分布集中,酸性强,同时还具有较大的比表面积和微孔孔容.以该分子筛制备的Pt/SAPO-11催化剂在正十四烷临氢异构反应中表现出较高的催化活性和异构选择性.     

导向剂法制备SAPO-11分子筛及其加氢异构化性能

采用导向剂法在模板剂用量减半的条件下成功合成小晶粒介孔SAPO-11分子筛。对合成分子筛的晶体结构、形貌、孔结构和酸类型进行表征。以长链烷烃正十二烷作为反应原料,考察Pt负载量为0. 5(wt)%的SAPO-11分子筛的加氢异构化反应性能。结果表明,将模板剂使用量减半合成的SAPO-11分子筛晶粒尺寸约为3μm,介孔比表面积为113. 3m~2/g,介孔孔容为0. 328m~3/g,异构烃收率达到65. 31%。     

含HF体系中SAPO-11分子筛的合成与表征

 在含HF体系中合成了SAPO-11分子筛,并采用X射线衍射、扫描电镜、低温氮物理吸附、红外光谱和吸附氨的程序升温脱附等手段对其进行了表征. 结果表明,相对于常规无HF合成体系,在HF体系中合成的SAPO-11分子筛样品结晶度提高,结晶速度加快,分子筛单晶增大,分子筛晶粒聚集体的粒径减小,比表面积降低,孔体积与平均孔径增大. 合成体系中加入HF后SAPO-11分子筛上B酸中心的总酸量和弱酸量降低,中强酸中心的比例有所提高,而L酸的酸量和酸强度无明显改变.     

以SBA-15为硅源合成多级孔SAPO-11分子筛及其在正十二烷临氢异构化中的应用

以脱除模板剂后的SBA-15为硅源和间接模板剂,在水热条件下制备多级孔SAPO-11分子筛,并通过XRD、SEM、红外光谱、氮气物理吸附-脱附等表征手段对样品的晶相、形貌、酸性和织构性质进行表征。结果表明,以焙烧后的SBA-15为硅源合成出纯相的SAPO-11分子筛,且SBA-15已完全转化。合成的SAPO-11样品呈空心的近方柱体形貌,由宽度为100 nm左右的细条聚集而成,晶粒粒径为1-3 μm。与白炭黑、硅溶胶合成的常规SAPO-11分子筛对比发现,添加SBA-15可在SAPO-11中引入介孔孔道,孔径为5-10 nm,且样品以中强度的Brønsted酸为主,弱Brønsted酸相对较少。以正十二烷为探针分子,考察Pt/SAPO-11催化剂的临氢异构化反应性能。结果表明,多级孔Pt/SAPO-11催化剂具有优良的异构化反应性能。催化剂的高活性和选择性与SAPO-11分子筛的酸性质和孔道结构密切相关,中强度的Brønsted酸量的增加有助于活性提高,同时介孔孔道有利于产物扩散,异构产物的选择性明显提高。     

CoSAPO-5分子筛的快速合成及高效催化α-蒎烯与空气环氧化反应

构建了用于催化空气环氧化α-蒎烯合成α-环氧蒎烷的高效、节能、绿色催化反应体系.首先,采用转动水热晶化模式合成了SAPO-5分子筛前驱体.相比于静态水热晶化模式,转动水热晶化模式可以显著缩短分子筛成核时间和晶化时间,同时可有效减小晶粒尺寸并显著提高晶粒尺寸的均一性.进一步对SAPO-5分子筛前驱体进行改性制得Co SAPO-5分子筛催化剂,并对反应溶剂、催化剂用量、反应温度和反应时间进行了优化.在获得的最优催化反应条件下,α-蒎烯转化率可达96.5%,α-环氧蒎烷产率可达89.0%.催化剂循环实验结果表明,该催化剂是稳定的、可多次循环使用的多相催化剂.     

SAPO-11分子筛合成条件对其结晶度与催化性能的影响

在水热条件下改变合成条件合成一系列SAPO-11分子筛,采用XRD对样品进行结晶度表征,并考察了合成条件对SAPO-11分子筛催化性能的影响.结果表明,合成条件对SAPO-11分子筛的结晶度和催化性能有很大影响.以二正丙胺(DPA)为模板剂,n(DPA)/n(Al2O3)=1.5,n(SiO2)/n(Al2O3)=0.2,晶化时间为24 h和晶化温度为170℃时,合成出的SAPO-11分子筛催化剂最有利于萘和甲醇的甲基化反应.初步探究其在萘和甲醇的甲基化反应中的失活原因.结果表明,催化剂失活的主要原因是在萘和甲醇的甲基化反应过程中生成大量的水,经高温水脱铝导致分子筛结构坍塌,从而导致分子筛失活.     

新型ZrAPO-11分子筛的合成与表征

利用水热法合成了APO-11、SAPO-11和ZrAPO-11分子筛.XRD结果证实,三者具有相同的AEL分子筛晶体结构;SEM照片显示,SAPO-11与APO-11都为5 μm～10 μm的球形颗粒,而ZrAPO-11呈10 μm～15 μm的棒状晶粒;N2吸附显示,除了0.45 nm的特征微孔外,三种分子筛还具有3.8 nm～3.9 nm的中孔结构;表面吸附和酸度表征证实,Zr主要存在与分子筛的孔道内,而Si则部分进入分子筛的骨架;吸附吡啶的DG-DTA研究发现,APO-11、ZrAPO-11同为弱酸性材料,而SAPO-11具有更强的酸性;原粉的DG-DTA证实,合成的稳定性良好,崩塌温度超过1 000     

SAPO-11分子筛的合成

以二正丙胺(DPA)为模板剂、利用水热法合成SAPO-11分子筛，系统考察了硅源、硅含量、模板剂用量以及晶化条件（晶化温度、时间以及pH值）对SAPO-11分子筛合成的作用。研究结果表明：硅源是决定SAPO-11分子筛合成及结构的关键组分之一，其释放出活性硅物种的速率要与磷酸铝分子筛的前驱体生成的速度相一致；酸性硅溶胶是合成SAPO-11的合适硅源；在SiO2/Al2O3=0～0.7，DPA/P2O5=0.8～1.8，pH=5.8～7.8条件下，可合成纯SAPO-11分子筛。此外，SAPO-11分子筛的合成，还存在明显的诱导期以及晶型的转化过程。在合成条件下，晶化时间4?h时，SAPO-11开始晶化，至24 h，SAPO-11分子筛可晶化完全。继续延长晶化时间，SAPO-11分子筛与SAPO-31分子筛之间发生转晶现象。     

SAPO-11/Beta复合分子筛的合成及其异构化性能研究

以Beta分子筛为硅源通过水热合成法合成了SAPO-11/Beta复合分子筛,采用X射线衍射、N2物理吸脱附、扫描电镜、透视电镜-能谱分析、固体核磁及吡啶红外等方法对单分子筛、复合分子筛和机械混合分子筛的物化性质进行了表征.以正十二烷为模型化合物,在固定床反应器上考察了铂负载型分子筛催化剂的异构化性能.结果表明,复合分子筛的物理化学性质明显不同于单分子筛和机械混合分子筛,其呈现核壳结构,SAPO-11和Beta间存在化学作用,使得复合分子筛具有适宜的B酸分布.在正十二烷异构化反应中,复合分子筛催化剂的异构化性能优于单分子筛催化剂和机械混合分子筛催化剂,多支链异构体收率高.     

溶剂热法合成用于正十二烷异构化的高活性富蛙Pt/SAPO-11催化剂

采用溶剂热法,利用不同的硅源和铝源合成了富硅的SAPO-11分子筛. 结果显示,与水热法合成的样品相比,溶剂热法合成的Pt/SAPO-11催化剂具有较大的外表面积,同时其硅含量、酸度和对正十二烷异构化的催化活性均显著提高. 在所有合成的Pt/SAPO-11催化剂样品中,以正硅酸乙酯与异丙醇铝为原料,采用溶剂热法合成的催化剂具有最高的酸度与正十二烷异构化活性.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Selective syntheses of 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones via temperature-dependent Rh(II)-carbenoid-mediated 2H-azirine-ring expansion

The Rh(II)-catalyzed reaction of 2-carbonyl-substituted 2H-azirines with ethyl 2-cyano-2-diazoacetate or 2-diazo-3,3,3-trifluoropropionate provides an easy access to 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones. These compounds can be selectively prepared from the same starting material using temperature as the only varied parameter. The 2-azabuta-1,3-diene intermediate, a common precursor for both heterocyclic products, isomerizes into 2H-1,3-oxazine under kinetic control, while 1H-pyrrol-3(2H)-one is the sole product of the reaction at elevated temperatures. According to DFT-calculations a one-atom oxazine ring contraction involving ring-opening to a 2-azabuta-1,3-diene intermediate, followed by a 1,5- and 1,2-prototropic shift leads to the consecutive formation of imidoylketene and azomethine ylide, which then further undergo cyclization to the pyrrole derivative.     

关于"对‘燃料电池物理及化学性能的有限时间热力学分析方法'的讨论”答复

把有限时间热力学理论用于化学过程的研究,将会得到一系列新的结论,开展这方面的研究是很有意义的.文献[1]以燃料电池为例,在同时考虑化学反应及传热不可逆性的情况下,研究了燃料电池的性能界限,文献[2]指出了文献[1]计算化学反应及传热不可逆性而引起系统与有关环境的总熵产生率的错误以及由此而导致的结论所存在的问题,并进行了富有启发性的分析与讨论.但文献[2]对于系统与有关环境的总熵产生率的计算也是不正确的,由此得到的其它结论自然不能成立.本文将就此情况下系统与有关环境的总熵产生率的计算再次进行讨论,并给出电池功率和效率的有限时间热力学性能界限.