SO2-4对铁基催化剂上费托合成反应的影响

以FeCuK/SiO2为母体催化剂,用不同浓度的NH4HSO4水溶液进行等体积浸渍,制备了不同SO2-4含量的费托合成(FTS)铁基催化剂.采用原子发射光谱、低温N2吸附、 X射线光电子能谱、程序升温还原和穆斯堡尔谱等技术对催化剂进行了表征,并在H2/CO摩尔比0.67,WHSV=2 000 h-1,压力1.5 MPa和温度250 ℃条件下进行了浆态床FTS反应.结果表明,少量SO2-4能促进催化剂在H2中的还原;在合成气还原过程中,少量SO2-4对催化剂的碳化程度影响不大,但大量SO2-4严重抑制催化剂的碳化.在约500 h的运行实验中,各催化剂样品表现出的催化活性有所差异,但均呈现较好的稳定性.SO2-4可抑制水煤气变换反应活性,且随着SO2-4含量的增加,抑制作用愈加明显;同时,催化剂上浸渍少量SO2-4可有效抑制CH4的生成,提高低碳烯烃的选择性.     

浸渍钠对铁基催化剂F-T合成浆态床反应性能的影响

以FeCuK/Si O2为母体催化剂,通过乙酸钠浸渍得到一组不同Na含量的费托合成铁基催化剂.采用原子发射光谱、低温N2吸附、程序升温还原和M ssbauer谱等技术对催化剂进行了表征.在H2/CO摩尔比为0.67,空速为2 000 h-1,压力为1.5 MPa和温度为250℃的条件下进行了浆态床F-T合成反应性能评价实验.结果表明,浸渍少量Na能提高催化剂的比表面积,促进铁物相的分散,而浸渍大量Na却大大降低了催化剂的比表面积,使催化剂中的铁物相聚集形成较大的颗粒;浸渍Na抑制了催化剂在H2中的第一步还原,但促进了催化剂在CO中的碳化;在原位合成气还原过程中,浸渍Na有利于催化剂的碳化.在500 h的运行实验中,浸渍Na的催化剂均表现出不同程度的失活现象.反应结果表明,浸渍Na对水煤气变换反应活性影响不大,对费托合成反应活性和烃产物选择性有较大的影响.在铁基催化剂上浸渍Na有利于C12 重质烃和低碳烯烃的生成.     

SO_4~(2-)/TiO_2光催化氧化邻硝基苯酚

采用不同浓度的硫酸溶液浸渍处理TiO2,制得不同SO42-含量的SO42-/TiO2光催化剂.考察了光催化剂对邻硝基苯酚溶液的光催化行为.发现SO42-/TiO2的光催化活性高于TiO2的光催化活性,浸渍液中H2SO4的浓度和焙烧温度对SO42-/TiO2的催化活性有一定的影响,最佳浸渍H2SO4浓度为0.5 mol.L-1,最佳焙烧温度为500℃.     

SO42-/ZrO2-TiO2催化苯与1-十二烯烷基化合成十二烷基苯

利用沉淀-浸渍法制备了SO42-/ZrO2-TiO2固体酸催化剂,优化了SO42-/ZrO2-TiO2催化苯与1-十二烯烷基化合成十二烷基苯的工艺条件,并通过IR及GC/MS对产物的结构进行了表征.结果表明: SO42-/ZrO2-TiO2对苯与1-十二烯的烷基化反应具有良好的催化性能,其催化中心主要为B酸中心.0.12g催化剂/ mL1-十二烯、n(苯)/n(烯)=6:1、反应时间3 h等优化条件下1-十二烯转化率100%,LAB与2-LAB选择性分别达到90.3%和88.6%.使用后的催化剂可以通过H2SO4浸渍500 ℃焙烧再生.GC/MS分析表明产物主要包括2～6-LAB及少量二烷基苯.     

固体酸催化剂SO4^2-／SiO2-TiO2的制备及其催化酯化性能

分别以机械混合法和浸渍法制备了SO42-/SiO2-TiO2固体酸催化剂,以乙醇和乙酸的酯化反应为模型反应考察了不同SiO2含量及不同温度焙烧的催化剂的活性.结果表明,机械混合法制备的400℃焙烧的SO42-/40%SiO2-TiO2催化剂活性最高,部分回流时,乙酸几乎全部转化,全回流反应100min时,其乙酸转化率达到84%.X射线衍射分析表明,SiO2抑制了硫酸氧钛的形成;催化剂的活性组分包括一定量的四方晶锐钛矿型TiO2、正交晶硫酸氧钛、少量立方晶金属钛和高比表面积的SiO2.红外光谱分析表明,添加SiO2后催化剂形成Ti-O-Si键,进而使SO42-与样品表面产生强相互作用;结合的SO42-主要以无机螯合状双配位和有机硫酸酯两种结构形式存在.热重-示差扫描量热分析表明,SiO2的添加使SO42-不易脱除,同时使锐钛矿TiO2向金红石相的转变温度降低.     

硫酸钠对Mn/SiO2催化剂结构及其甲烷氧化偶联反应性能的影响

 采用等体积浸渍法制备了Na2SO4改性的Mn/SiO2催化剂,考察了Mn-Na2SO4/SiO2催化剂中各组分对甲烷氧化偶联合成C2产物(C2H4+C2H6)的影响,并采用X射线衍射、 X射线光电子能谱、 Raman光谱和程序升温还原等手段表征了催化剂中的物相结构、表面组分价态与含量以及氧化还原性能. 结果表明,在Mn/SiO2催化剂中添加Na2SO4可使载体SiO2由无定形转变为α-方石英相,使催化剂表面的Mn物种由Mn3O4转变为Mn2O3, 从而大大提高了甲烷转化率和目标产物C2的选择性. 因此,推测Mn2O3物种在反应条件下构成了甲烷氧化偶联反应的活性中心.     

SO_4~(2-)/SnO_2/SBA-15固体酸催化剂的制备及其在环酮缩合反应中的应用

采用等体积浸渍法制备了不同负载量的固体酸催化剂SO42-/SnO2/SBA-15,利用X射线粉末衍射、N2吸附-脱附和透射电镜等手段对样品进行了表征,并考察了催化剂对4-叔丁基环己酮与乙二醇缩合反应的催化性能.结果表明,SO42-/SnO2催化剂负载于SBA-15后其催化性能明显改善.研究了SO42-/20%SnO2/SBA-15催化剂上部分酮类化合物与乙二醇及1,2-丙二醇的缩合反应,并考察了反应时间和催化剂用量等因素对反应性能的影响.在适宜的温和条件下,一些环酮类底物如环己酮、4-甲基环己酮和4-叔丁基环己酮等均可反应得到相应的缩醛化产物,且催化剂至少可循环使用4次.     

浆态床F-T合成Fe/Cu/K/SiO2催化剂中K助剂作用的研究

采用低温N2吸附、H2 TPR、CO2 TPD、MES、XRD,考察了K的加入顺序对两组微球状费托(F-T)合成Fe/Cu/K/SiO2催化剂的织构性质、还原行为、碳化行为、物相变化以及反应性能的影响。结果表明,K的加入顺序对催化剂的织构性质影响很小。先加Si后加K的催化剂具有较强的表面碱性,抑制催化剂在H2气氛下的初始还原,但促进了催化剂的碳化,且在浆态床F T反应中表现出良好的反应稳定性,较高的FTS反应活性,较低的甲烷选择性以及较高的重质烃和烯烃选择性,表现出良好的工业应用前景。     

固体酸催化剂SO2-4/SiO2-TiO2的制备及其催化酯化性能

 分别以机械混合法和浸渍法制备了SO2-4/SiO2-TiO2固体酸催化剂,以乙醇和乙酸的酯化反应为模型反应考察了不同SiO2含量及不同温度焙烧的催化剂的活性. 结果表明,机械混合法制备的400 ℃焙烧的SO2-4/40%SiO2-TiO2催化剂活性最高,部分回流时,乙酸几乎全部转化,全回流反应100 min时,其乙酸转化率达到84%. X射线衍射分析表明, SiO2抑制了硫酸氧钛的形成; 催化剂的活性组分包括一定量的四方晶锐钛矿型TiO2、 正交晶硫酸氧钛、少量立方晶金属钛和高比表面积的SiO2. 红外光谱分析表明,添加SiO2后催化剂形成 Ti-O-Si 键,进而使SO2-4与样品表面产生强相互作用; 结合的SO2-4主要以无机螯合状双配位和有机硫酸酯两种结构形式存在. 热重-示差扫描量热分析表明, SiO2的添加使SO2-4不易脱除,同时使锐钛矿TiO2向金红石相的转变温度降低.     

制备方法对H2SO4固体酸结构和催化性能的影响

 以溶胶-凝胶法和浸渍法制备了H2SO4固体酸催化剂. FT-IR, XRD和 29Si MAS NMR结果表明,两种方法得到的催化剂结构不同. FT-IR和 29Si MAS NMR结果表明,溶胶-凝胶法制备的固体酸H2SO4-SiO2中H2SO4和载体SiO2间存在相互作用; 1H MAS NMR结果表明,H2SO4-SiO2固体酸的酸强度和液体浓硫酸相当. 通过对柠檬酸与正丁醇的液/固相催化酯化反应比较了溶胶-凝胶法与浸渍法制备的固体酸的催化性能,结果表明,浸渍法得到的固体酸重复使用4次后活性消失; 溶胶-凝胶法制备的H2SO4-SiO2固体酸重复使用6次后仍显示出较高的活性和选择性.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.