Cellulose nanofibril (CNF) aerogels have attracted great interests in recent years due to the low cost, sustainability and biocompatibility of raw CNF. However, the poor thermal stability and flammable feature of CNF aerogels have limited their wider applications. In this paper, polydopamine/CNF composite aerogels with good comprehensive properties are fabricated by modification of CNF with polydopamine and metal coordination bonds crosslinking. The microstructure and properties of composite aerogels are thoroughly characterized by a variety of tests. It is found that the microstructure of aerogels are more regular and the compressive strength of aerogels are enhanced by the incorporation of polydopamine and Fe3+ crosslinking. Importantly, the thermal stability and flame resistance of aerogels are significantly improved, which permit the application of composite aerogels in high-temperature thermal insulation. In addition, the reversible characteristic of metal coordination bonds allows the water induced healing of fractured composite aerogels. This study is expected to provide information for future development of green and high-performance aerogels.
The Cu-doped SiO2 composite aerogels were successfully prepared by sol–gel process and subsequently supercritical drying with ethanol and CO2. The Cu-doped SiO2 composite aerogels had porous texture, low density (<100 mg cm?3) and high specific surface area (>800 m2 g?1), which were investigated by FESEM and nitrogen adsorption desorption porosimetry. The FTIR spectra of the aerogels showed that the ethanol-dried aerogels had been modified by ethyl while the corresponding CO2-dried aerogels had more Si–OH groups. The phase structure and thermal stability were investigated by XRD and TGA, respectively. Due to the reducibility of ethanol, the copper was crystalline in ethanol-dried sample. The Cu-doped SiO2 composite aerogels dried with supercritical ethanol had larger pore diameter and better thermal stability under 400 °C in comparison with CO2-dried composite aerogels. The structures and properties of Cu-doped SiO2 composite aerogels are obviously affected by supercritical drying conditions. The effect research could instruct the synthesis of different state of Cu in composite aerogels. 相似文献
A comparative analysis of properties of SiO2–TiO2 binary aerogels prepared by supercritical drying using different supercritical fluids (isopropanol, hexafluoroisopropanol, methyl tert-butyl ether, and CO2) has been performed. The use of different supercritical fluids allows preparation of both homogeneous amorphous SiO2–TiO2 binary aerogels (by supercritical drying in hexafluoroisopropanol and CO2) and composite aerogels containing nanocrystalline anatase (by supercritical drying in isopropanol and methyl tert-butyl ether). The thermal treatment of the aerogels at temperatures up to 600°C does not lead to considerable change in the porous structure and phase composition of the aerogels. 相似文献
TiO2–SiO2 composite aerogels were prepared via ambient pressure drying by sol–gel and surface modification for both the sol and gel samples. The organosilane reagents of decamethyltetrasiloxane (DMTSO)/trimethylchlorosilane (TMCS) and hexamethyldisiloxane (HMDSO)/TMCS were introduced into the TiO2–SiO2 composite sol for pre-modification respectively, and subsequently the TMCS/hexane solution was used for surface modification of the obtained TiO2–SiO2 composite gel. The effects of sol pre-modification on the microstructure and pore characteristics of TiO2–SiO2 composite aerogels were investigated. The results indicate that HMDSO/TMCS coupling reagents is more appropriate for the pre-modification of TiO2–SiO2 composite sol than the DMTSO/TMCS reagents. The best volume ratio of HMDSO/TMCS/composite sol for preparing mesoporous TiO2–SiO2 composite aerogels is in the range of 1:0.33:10–1:1.0:10, with which the specific surface area and pore volume of the obtained TiO2–SiO2 composite aerogels are 492–645 m2/g and 2.63–2.85 m3/g, respectively. The results of adsorption and photocatalytic degradation of rhodamine B show that the as-prepared TiO2–SiO2 composite aerogels have higher adsorption/photocatalysis. Particularly, the as-prepared TiO2–SiO2 composite aerogels with HMDSO/TMCS showed prominent adsorption capability with the adsorption rate attaining to 89.4 % within 60 min. 相似文献
Organic aerogels based on two important and widely abundant renewable resources, soy proteins (SP) and nanofibrillar cellulose (NFC) are developed from precursor aqueous dispersions and a facile method conducive of channel- and defect-free systems after cooling and freeze-drying cycles that yielded apparent densities on the order of 0.1 g/cm3. NFC loading drives the internal morphology of the composite aerogels to transition from network- to fibrillar-like, with high density of interconnected cells. Composite aerogels with SP loadings as high as ca. 70 % display a compression modulus of 4.4 MPa very close to that obtained from reference, pure NFC aerogels. Thus, the high compression modulus of the composite system is not compromised as long as a relatively low amount of reinforcing NFC is present. The composite materials gain moisture (up to 5 %) in equilibrium with 50 % RH air, independent of SP content. Furthermore, their physical integrity is unchanged upon immersion in polar and non-polar solvents. Fast liquid sorption rates are observed in the case of composite aerogels in contact with hexane. In contrast, water sorption is modulated by the chemical composition of the aerogel, with an important contribution from swelling. The potential functionalities of the newly developed SP–NFC composite green materials can benefit from the reduced material cost and the chemical features brought about the amino acids present in SPs. 相似文献
Zr-containing organic aerogels were synthesized by ligand substitution reaction of polyzirconoxone and 2, 4-dihydroxybenzoic acid, followed by polymerization with formaldehyde, and then supercritical drying using CO2. After carbonization and carbothermal reduction under an argon atmosphere, ZrCO/C composite aerogels with controllable zirconium content (47.8–78.6 wt%) were obtained. The carbothermal reduction was substantially completed at 1,500 °C, and the obtained ZrCO/C composite aerogels exhibit low oxygen contents (9.4–6.7 wt%) and high surface areas (589–147 m2/g). Pore morphologies of the ZrCO/C composite aerogels were investigated in detail by nitrogen sorption measurements, scanning electron microscopy and its associated energy-dispersive X-ray microanalysis measurements. The results show that the aerogels are composed of carbon framework and Zr-conglomerations, and the surface area of aerogel is severely affected by its zirconium content. The presence of reductive ZrC crystals can greatly enhance the oxidation resistance ability of amorphous carbon framework and prevent collapse. 相似文献
Silica monolith aerogels with different degrees of hydrophobicity were prepared by incorporating methyltrimethoxysilane (MTMS) or trimethylethoxysilane (TMES) in standard sol-gel synthesis followed by supercritical drying of gels with carbon dioxide (CO(2)) at 40 degrees C and 100 bar. The hydrophobicity of the aerogels was tested by measuring the contact angle (theta). The aerogels were also characterised by FTIR, DSC, and porosity measurements. Adsorption capacity measurements show that such modified hydrophobic silica aerogels are excellent adsorbents for different toxic organic compounds from water. In comparison to granulated active carbon (GAC) they exhibit capacities which are from 15 to 400 times higher for all tested compounds. Adsorption properties of hydrophobic silica aerogel remain stable even after 20 adsorption/desorption cycles. 相似文献
The simpler non-supercritical drying approach has been used for the first time for the preparation of silica–silica composite aerogels (CA) and the efficiency of the process being demonstrated by testing the use of the aerogels for simulated high level nuclear waste confinement. Compositions of 5, 10, 20, 30, 40 and 50 wt% of silica (aerosil® 380) in silica–aerogel were prepared by introducing pyrogenic silica in to silica sol derived by hydrolysis of Tetraethoxy silane (TEOS). The silica–silica composite aerogels (CA) possessed very high surface area and low bulk densities. The effectiveness of the prepared composite aerogels as precursor for high level nuclear waste immobilized glass is also presented. Neodymium nitrate dissolved in isopropanol is used to simulate +3 valent actinides. The stability of neodymium in the glass matrix has been found to be extremely high. Transmission electron microscopy (TEM) has been used to characterise the aerogels as well as neodymium incorporated sintered gels. X-ray diffraction (XRD) studies of the sintered samples reveal the formation of neodymium silicates. 相似文献
We have prepared carbon aerogels (CAs) doped with cobalt or nickel through sol-gel polymerization of formaldehyde with the potassium salt of 2,4-dihydroxybenzoic acid, followed by ion exchange with M(NO3)2 (where M = Co2+ or Ni2+), supercritical drying with liquid CO2, and carbonization at temperatures between 400 and 1050 degrees C under a N2 atmosphere. The nanostructures of these metal-doped carbon aerogels were characterized by elemental analysis, nitrogen adsorption, high-resolution transmission electron microscopy (HRTEM), X-ray photoelectron spectroscopy (XPS), and X-ray diffraction (XRD). Metallic nickel and cobalt nanoparticles are generated during the carbonization process at about 400 and 450 degrees C, respectively, forming nanoparticles that are approximately 4 nm in diameter. The sizes and size dispersion of the metal particles increase with increasing carbonization temperatures for both materials. The carbon frameworks of the Ni- and Co-doped aerogels carbonized below 600 degrees C mainly consist of interconnected carbon particles with a size of 15-30 nm. When the samples are pyrolyzed at 1050 degrees C, the growth of graphitic nanoribbons with different curvatures is observed in the Ni- and Co-doped carbon aerogel materials. The distance of graphite layers in the nanoribbons is approximately 0.38 nm. These metal-doped CAs retain the overall open cell structure of metal-free CAs, exhibiting high surface areas and pore diameters in the micro- and mesoporic region. 相似文献
Activated carbon aerogels (ACAs) with high bimodal porosity were obtained for lithium/sulfur batteries by potassium hydroxide (KOH) activation. Then sulfur–activated carbon aerogels (S–ACAs) composites were synthesized by chemical deposition strategy. The S–ACAs composites were characterized by field emission scanning electron microscopy (FESEM), transmission electron microscopy, and N2 adsorption/desorption measurements. It is found that the activated carbon aerogels treated by KOH activation presents a porous structure, and sulfur is embedded into the pores of the ACAs network-like matrix after a chemical deposition process. The Li/S–ACAs (with 69.1 wt% active material) composite cathode exhibits discharge capacities of 1,493 mAh g?1 in the first cycle and 528 mAh g?1 after 100 cycles at a higher rate of C/5 (335 mA g?1). The S–ACAs composite cathode exhibits better electrochemical reversibility, higher active material utilization, and less severe polysulfide shuttle than S–CAs composite cathode because of high bimodal porosity structure of the ACAs matrix. 相似文献
With increasing energy demand driving the need for eco-friendly and efficient energy storage technology, supercapacitors are becoming increasingly prevalent in wearable devices because of their portability and stability. The performance of these supercapacitors is highly dependent on the choice of electrode material. The high capacitance and mechanical properties needed for these materials can be achieved by combining graphene’s stable electrical properties with renewable cellulose’s excellent mechanical properties into porous aerogels. In this study, graphene-cellulose hydrogels were prepared by a one-step hydrothermal method, with porous, ultra-light, and mechanically strong graphene-cellulose aerogels then prepared by freeze-drying. These composite aerogels possess excellent mechanical strength and high specific capacitance, capable of bearing about 1095 times the pressure of their own weight. Electrochemical tests show the specific capacitance of these composite aerogels can reach 202 F/g at a scanning rate of 5 mA/cm2. In view of their high surface area and fast charge transport provided by their 3D porous structure, graphene-cellulose aerogels have great potential as sustainable supercapacitor electrodes. 相似文献
The experimental results on the organic modification of tetraethoxysilane (TEOS) based silica aerogels synthesized by co-precursor and derivatization methods are reported and discussed. In order to obtain silica aerogels with better physicochemical properties in terms of higher hydrophobicity, optical transmission and thermal stability, eight organosilane compounds (hydrophobic reagents) of the type RnSiX4–n have been used. The molar ratio of tetraethoxysilane (TEOS), ethanol (EtOH), water (0.001 M oxalic acid catalyst) was kept constant at 1:5:7 respectively. The organically modified silica aerogels were produced by two different methods: (i) Co-precursor method and (ii) Derivatization method. In the former method, the molar ratio of hydrophobic reagent (HR) to TEOS was varied from 0.1 to 0.6. In the later method, derivatization of the wet gels was carried out using 20% hydrophobic reagent in methanol. The merits and demerits of both these methods have been presented. The organic surface modification of the aerogels was confirmed by the Fourier Transform Infrared (FTIR) spectroscopic studies and the contact angle measurements. In the co-precursor method, with the increase in hydrophobic reagent/TEOS molar ratio, the hydrophobicity increases ( = 136°) and the optical transmission decreases (5%), whereas in the derivatization method the optical transmission is very high (T 85%) but the hydrophobicity is low ( = 120°). The thermal stability of the hydrophobic aerogels (the temperature up to which the hydrophobicity is retained) was studied in the temperature range of 25–800°C. The aerogels based on the co-precursor method retained the hydrophobicity up to a temperature as high as 520°C and on the other hand, the derivatized aerogels are hydrophobic only up to a temperature of 285°C. For the first time, TEOS based hydrophobic silica aerogels have been obtained with negligible volume shrinkage using the trimethylethoxysilane (TMES) co-precursor. The aerogels were characterized by Fourier transform infrared spectroscopy (FTIR), optical transmittance, Scanning Electron Microscope (SEM), thermogravimetric (TG) and differential thermal (DT) analyses and the contact angle measurements. 相似文献
To enhance the mechanical properties of three-dimensional graphene aerogels with aramid fibers,graphene/organic fiber aerogels are prepared by chemical reduction of graphene oxide in the presence of organic fibers of poly(p-phenylene terephthalamide)(PPTA) and followed by freeze-drying. Thermal annealing of the composite aerogels at 1300 ° C is adopted not only to restore the conductivity of the reduced graphene oxide component but also to convert the insulating PPTA organic fibers to conductive carbon fibers by the carbonization. The resultant graphene/carbon fiber aerogels(GCFAs) exhibit high electrical conductivities and enhanced compressive properties, which are highly efficient in improving both mechanical and electrical performances of epoxy composites. Compared to those of neat epoxy, the compressive modulus, compressive strength and energy absorption of the electrically conductive GCFA/epoxy composite are significantly increased by 60%, 59% and 131%, respectively. 相似文献
A detailed study of CdSe aerogels prepared by oxidative aggregation of primary nanoparticles (prepared at room temperature and high temperature conditions, >250 degrees C), followed by CO2 supercritical drying, is described. The resultant materials are mesoporous, with an interconnected network of colloidal nanoparticles, and exhibit BET surface areas up to 224 m2/g and BJH average pore diameters in the range of 16-32 nm. Powder X-ray diffraction studies indicate that these materials retain the crystal structure of the primary nanoparticles, with a slight increase in primary particle size upon gelation and aerogel formation. Optical band gap measurements and photoluminescence studies show that the as-prepared aerogels retain the quantum-confined optical properties of the nanoparticle building blocks despite being connected into a 3-D network. The specific optical characteristics of the aerogel can be further modified by surface ligand exchange at the wet-gel stage, without destroying the gel network. 相似文献
Bio‐derived polysaccharide aerogels are of interest for a broad range of applications. To date, these aerogels have been obtained through the time‐ and solvent‐intensive procedure of hydrogel fomation, solvent exchange, and scCO2 drying, which offers little control over meso/macropore distribution. A simpler and more versatile route is developed, using freeze drying to produce highly mesoporous polysaccharide aerogels with various degrees of macroporosity. The hierarchical pore distribution is controlled by addition of different quantities of t‐butanol (TBA) to hydrogels before drying. Through a systematic study an interesting relationship between the mesoporosity and t‐butanol/water phase diagram is found, linking mesoporosity maxima with eutectic points for all polysaccharides studied (pectin, starch, and alginic acid). Moreover, direct gelation of polysaccharides in aqueous TBA offers additional time savings and the potential for solvent reuse. This finding is a doorway to more accessible polysaccharide aerogels for research and industrial scale production, due to the widespread accessibility of the freeze drying technology and the simplicity of the method.
The experimental results on the synthesis of flexible and superhydrophobic silica aerogels using methyltrimethoxysilane (MTMS) precursor by a two-step (acid-base) sol-gel process followed by the supercritical drying, are reported. The effects of various sol-gel parameters on the flexibility of the aerogels have been investigated. The aerogels of different densities were obtained by varying the molar ratio of MeOH/MTMS (S) from 14 to 35, with lower densities for larger S values. It has been observed that the Young's modulus (Y) decreased from 14.11 x 10(4) to 3.43 x 10(4) N/m(2) with the decrease in the density of the aerogels from 100 to 40 kg/m(3). Simultaneously, the aerogels are superhydrophobic with a contact angle as high as 164 degrees . The superhydrophobic aerogels are thermally stable up to a temperature of 530 K, above which they become hydrophilic. The aerogels have been characterized by bulk density, percentage volume shrinkage, and porosity measurements. The microstructures of the aerogels have been studied using the transmission electron microscopy (TEM). The Young's modulus of the aerogels has been determined by an uniaxial compression test. The variation of physical properties of the aerogels has been explained by taking into consideration the hydrolysis, condensation reactions, the resulting colloidal clusters and their network formation. 相似文献