BaxCe0.8Y0.2O3-α固体电解质的氧离子导电性

Ba_xCe_0.8Y_0.2O_3-α(x=1.03，1，0.98) solid electrolyte samples show a single phase of orthorhombic perovskite of BaCeO₃. The oxide-ion conduction and transport number were detected in the temperature of 600～1000℃ by electrochemical oxygen permeation (oxygen pumping)， and compared with the results from the oxygen concentration cell. The relation between the ingredient of Ba and oxide-ion conduction was also researched. It was found that these electrolytes exhibited the mixed oxide-ionic and electronic hole conduction under the experimental temperature and oxygen gas. The oxide-ion transport numbers are 0.1～0.6， which are close to the results of the oxygen con-centration cell. They increase as the decrease of Ba content in the samples.     

BaCe0.8Ho0.2O3-a陶瓷的性质与应用

Ceramic BaCe0.8Ho0.2O3-α with orthorhombic perovskite structure was prepared by conventional solid state reaction, and its conductivity and ionic transport number were measured by ac impedance spectroscopy and gas concentration cell methods in the temperature range of 600-1000 ℃ in wet hydrogen and wet air, respectively. Using the ceramics as solid electrolyte and porous platinum as electrodes, the hydrogen-air fuel cell was constructed, and the cell performance at temperature from 600-1000 ℃ was examined. The results indicate that the specimen was a pure protonic conductor with the protonic transport number of 1 at temperature from 600-900 ℃ in wet hydrogen, a mixed conductor of proton and electron with the protonic transport number of 0.99 at 1000 ℃. The electronic conduction could be neglected in this case, thus the total conductivity in wet hydrogen was approximately regarded as protonic conductivity. In wet air, the specimen was a mixed conductor of proton, oxide ion and electron hole. The protonic transport numbers were 0.01-0.09, and the oxide-ionic transport numbers were 0.27-0.32. The oxide ionic conductivity was increased with the increase of temperature, but the protonic conductivity displayed a maximum at 900 ℃, due to the combined increase in mobility and depletion of the carriers. The fuel cell could work stably. At 1000 ℃, the maximum short-circuit current density and power output density were 346 mA/cm^2 and 80 mW/cm^2, respectively.     

SrCe0.95Er0.05O3-α固体电解质的导电性

SrCe_0.95Er_0.05O_3-α ceramic of a single orthorhombic phase of perovskite-type SrCeO₃ was prepared by high-temperature solid state reaction. Using the ceramic as solid electrolyte and porous platinum as electrodes, the measurements of conductivities and ionic transport numbers on SrCe_0.95Er_0.05O_3-α ceramic were performed by using electrochemical methods in the temperature range of 600～1 000 ℃ in wet hydrogen, dry air and wet air, respectively. The results indicate that the sample is a pure protonic conductor with a maximal conductivity of 0.01 S·cm^-1 in wet hydrogen, a mixed conductor of oxide-ion and hole in dry air, and a mixed conductor of proton, oxide-ion and hole in wet air.     

Ce0.8Y0.2O1.9-Ca3(PO4)2-K3PO4复合电解质在中温区的质子导电性及在常压合成氨中的应用

A precursor of Ce_0.8Y_0.2O_1.9(YDC) solid electrolyte was synthesized by the gol-gel method. YDC and phosphates powders were prepared by mixing the YDC and phosphates according to different weight ratios. The mixtures of the YDC and binary phosphates were ground and sintered at 1 400 ℃. The proton conductivity in solid electrolyte of the sintered samples was examined using electrochemical methods at 400～800 ℃. Ammonia was synthesized from nitrogen and hydrogen at atmospheric pressure in the solid state proton conducting cell reactor. The optimal condition for the ammonia production was determined. The result indicated that composite electrolyte of 80wt% YDC: 20wt% binary phosphates as proton conductor could obtain the highest ionic conductivity and ammonia production rate among the four samples, the rate of evolution of ammonia was up to 9.5 × 10^-9 mol·s^-1·cm^-2.     

中温固体氧化物燃料电池复合阴极La1.6Sr0.4NiO4-Ce0.9Gd0.1O1.9的制备及性能研究

Composite cathodes consisting of -La_1.6Sr_0.4NiO₄(LSN) and -Ce_0.9Gd_0.1O_1.9(CGO) has been prepared for intermediate temperature solid oxide fuel cell (IT-SOFC). The chemical stability, microstructures and electrochemical performance of the cathode have been investigated using XRD, SEM and AC impedance spectroscopy. Results showed that strong bonding was formed between the composite electrodes and CGO electrolytes after the electrodes were fired at 1 050 ℃ for 4 hours. The polarization resistance changed with oxygen partial pressure, suggesting that charge transfer process was the rate limiting step for electrochemical oxygen reduction at the composite cathodes. Area specific resistance (ASR) for a LSN-40CGO composite cathode was 0.76 Ω·cm² at 700 ℃, which was four times lower than that of a pure LSN cathode. 1.7％ decrease of the cathode current density was observed in the stability test of the composite cathode.     

纳米晶PbTiO3负载CuO催化NO分解

A large specific surface area perovskite-type mixed oxide PbTiO₃ supported cupric oxide was synthesized as a catalyst for NO decomposition and characterized by techniques such as XPS, XRD, H₂-TPR before and after NO decomposition reactions. The catalytic properties were tested with a fix-bed micro-reactor. The results showed that the PbTiO₃ was inactive for the reactions, but 1wt % Cu/PbTiO₃ catalyst gave fairly good activities for NO decomposition at temperature as low as 473 K. Copper species were found well-dispersed but weakly interacted with the support before NO decomposition, and the NO decomposition caused significant change in the environment of the copper species, which became Cu(Ⅰ) and most probably incorporated into surface crystal lattice of the nano-sized PbTiO₃. In NO reaction, a large amount of oxygen atoms from the decomposition of NO penetrated into the nano-sized PbTiO₃ support and caused small expansion of crystal lattice. The transport of oxygen between the copper species and the catalyst support may be helpful to speed up the kinetic regeneration of active metal sites from oxygen occupancy and resulted in good catalytic performance.     

La0.9Sr0.1Al0.9Mg0.1O3-δ-Ca3(PO4)2-K3PO4复合电解质的合成及在常压天然气合成氨中的应用

La_0.9Sr_0.1Al_0.9Mg_0.1O_0.9(LSAM) was synthesized by the sol-gel method, an oxide-salt composite electrolyte LSAM-Ca₃(PO₄)₂-K₃PO₄ was prepared by mixing the LSAM and phosphates. The mixture was ground and sintered at 1 400 ℃. Using the LSAM electrolyte and its oxide-salt composite as solid electrolytes and silver-palladium alloy as electrodes, electrical conductivity was measured at different conditions. Ammonia was synthesized from wet natural gas and nitrogen at atmospheric pressure in the solid state proton conducting cell reactor and the optimal conditions for ammonia production were determined. The oxide-salt composite exhibited much higher ionic conductivity and ammonia production rate than that of the LSAM electrolyte at 400～800 ℃, the rate of evolution of ammonia was up to 5.30 × 10^-9 mol·cm^-2·s^-1.     

BaCe0.9Nd0.1O3-δ柠檬酸盐法合成、表征及其在中温区的电导率

A precursor of BaCe_0.9Nd_0.1O_3-δ solid electrolyte was synthesized by the sol-gel method and sintered at 1400℃.The obtained gels and powder were characterized by differential and ther mogravimetric thermal analysis(TG-DTA),X-ray diffraction(XRD), transmissi on electron microscopy(TEM).Using the sintered samples as solid electrolyte and silver-palladium alloy as electrodes,electrical conductivities under different gas ambiences at intermediate temperature (400～600℃) were measured. In moist hydrogen atmosphere, the conduction is a little higher than that of dry hydrogen atmosphere. In hydrogen atmosphere, proton conduction may predominate, leading to an increase in conductivity and a decrease in activation energy.     

新型阴极材料Ba0.5Sr0.5Co0.8Fe0.2O3-σ制备与性能研究

Ba_0.5Sr_0.5Co_0.8Fe_0.2O_3-σ(BSCF), a new cathode material for solid oxide fuel cell (SOFC), was synthesized by polyacrylicacid (PAA) method. The lattice structures of samples calcined at different temperatures were characte-rized by XRD. Shrinkage, porosity and pore size of the porous BSCF as a function of sintering temperature were investigated. It was found that the cubic perovskite structure could be formed after calcination at 800 ℃ for 2 h, but not well crystallized as seen from some unknown phases, and the pure cubic perovskite structure was formed after calcination at 1 150 ℃ for 2 h. The particle size of BSCF was less than 1～2 μm. The shrinkage of the porous BSCF increased with sintering temperature, but the opposite was true for the porosity. After sintering at 1 100 ℃ for 4 h, the porous BSCF was still in an appropriate structure, with porosity of 29% and electrical conductivity above 400 S·cm^-1.     

BaO-Al2O3-B2O3系密封玻璃的结构与性质

The BaO-Al₂O₃-B₂O₃ glasses manufactured for solid oxide fuel cell(SOFC) sealing were studied. The effect of different n_BaO/n_B2O3 on crystal, thermal properties, density and infrared spectra of this system has been discussed. The results show that the trends of crystallization, glass transformation temperature, dilatometric softening temperature and density increase with n_BaO/n_B2O3 values. But a typical property deviation occurs when n_BaO/n_B2O3 is 0.875, and its coefficient of thermal expansion has the maximum at this point. The changes of properties can attribute to the conversion of boron from tetrahedral coordination to trigonal, breakage of the local glass network and interaction between the network modifiers. These can be proved by infrared spectra of glasses. Thermal properties of some studied samples are suitable for the sealing of SOFC using Sm doped ceria electrolyte and operating at 400～600 ℃.     

N2O活化的Fe/ZSM-5表面活性氧的表征(英)

Temperature-programmed reduction (H₂-TPR) was employed to quantitatively characterize the active oxygen species generated from a high Fe-loading Fe/ZSM-5 catalyst exposed to N₂O at 250 ℃. [Fe-O-Fe]²⁺ dimer was determined as the active iron complex for N₂O decomposition to produce the active oxygen. Reduction of Fe³⁺ to Fe²⁺ by H₂ in the dimer and removal of OH^- groups from Fe²⁺ dimer by heating Fe/ZSM-5 to 700 ℃ were the prerequisites for the formation of this active Fe complex. A linear correlation with a slope of 1.0 between the amount of [Fe-O-Fe]²⁺ and that of active oxygen species was observed. Maximum amount of active oxygen species can be generated by reducing Fe/ZSM-5 catalyst with H₂ at the temperatures over 500 ℃ and then heating the resulting product in Ar to 700 ℃, followed by N₂O exposure at 250 ℃. The ratio of the total number of oxygen atoms (Ode) deposited by interaction of [Fe-O-Fe]²⁺ with N₂O to the amount of [Fe-O-Fe]²⁺ was 2. However, not all the deposited oxygen atoms were active oxygen (O_a); the ratio of O_a and O_de was 0.5. The iron dimer complex composing active oxygen is a five-atom ion [Fe₂O₃]²⁺; the most probable structure is as follows:     

Preparation and characterization of a new polymer electrolyte (PEO:NaClO3) for battery application

A new sodium-ion conducting thin-film polymer electrolyte based on the poly(ethylene oxide) (PEO) system has been prepared by a solution-casting method. Characterization by XRD, IR, and AC conductivity and Wagner's polarization were carried out on these thin-film electrolytes. From the transference number experiment it was found that the charge transport in these electrolytes is mainly due to ions. Conductivity studies show that the conductivity value of the PEO:NaClO₃ complex increases with the increase of salt concentration. An increase in the conductivity and a change in the cell parameters for the electrolyte system were found by the addition of the low molecular weight dimethylformamide or propylene carbonate as plasticizers. The cell parameters of these electrolyte systems were measured from a discharge study of the cell with the application of a load of 100 kΩ at room temperature in the common cell configuration Na|electrolyte|MnO₂. The open circuit voltage ranges from 2.02 V to 2.46 V and the short circuit current ranges from 570 μA to 1030 μA. Electronic Publication     

有机溶液中电化学制备纳米MgTiO3

In a cell without separating the cathode and anode spaces, the precursor MgTi(OCH₂CH₃)_(6-y)(acac)_y of the mixed oxide MgTiO₃ was directly synthesized by electrochemical dissolution of titanium for 4 hours and then of magnesium for 1 hour 40 minutes at the current of 0.2 A in ethanol and acetyl-acetone solution. The nano- MgTiO₃ powder was prepared by a direct sol-gel process of the electrolyte solution under pH≈8.5 followed by washing, drying in vacuum for 24 h, and calcination at 500 ℃ for 2 h. IR and Raman spectroscopy, XRD, and TEM were used to investigate the structure of nano-MgTiO₃ and its precursor. The result suggested that it was more appropriate to control the temperature between 35～40 ℃ and the concentration of conductive additive (Bu₄N)Br at 0.04 mol·L^-1. The xerogel with an average particle size of 12 nm and the nano-MgTiO₃ of 20 nm was thus obtained in a high purity.     

ZrWO4F2的前驱物法合成和表征

Zirconium tungsten oxyfluoride, ZrWO₄F₂, was firstly synthesized with the precursor route. The composition of the compound was determined by combining the results of ICP and XPS. The indexed powder X-ray diffraction pattern of this compound indicates that it is a pure phase, orthorhombic crystal system, space group D₂²=P2₁22 and a=15.32(2)?,b=13.877(7)?,c=8.42(2)?.Combining the results of the DTA-TGA curves from room temperature to 700℃ and XRD patterns in different temperatures the mechanism was revealed during the solid precursor (1) been heated to 700℃. The zirconium tungsten oxyfluoride was considered to be a metastable com-pound. The ascertaining of annealing time and temperature is the key of handling.     

电镀烧结法制备Ti/SnO2-Sb2O4电极的研究

The Ti/SnO₂-Sb₂O₄ electrode has been prepared by the electroplate-sinter method. The effect of SbCl₃ adding amount and sintering temperature on its electrode lifetime and oxygen evolution potential were investigated by means of EDX, SEM and XRD analysis. The results indicated that the electrode appeared the best performance when the SbCl₃ adding amounts was 0.2g and the sintering temperature was 550℃. In optimized conditions Ti substrate was entirely covered by SnO₂-Sb₂O₄ and the combinations among them were tight. Due to the use of electroplate method, the electrical conductivity, the oxygen evolution potential and the electrode lifetime were increased, so the elec-tro-catalytic activity and the electrochemical stability of the prepared electrode were found to be superior.     

机械球磨与反应烧结合成Sr2CeO4发光体的研究

Sr₂CeO₄ phosphor was synthesized by mechanical milling and reactive sintering in this work. The solid state reaction of SrCO₃and CeO₂ (2∶1) started at about 850 ℃ and completed at 1 000 ℃ for about 4 h. Two types of formation mechanism of Sr₂CeO₄ were proposed. When the starting powder mixture was fired above 1 000 ℃, the unstable intermediate phase SrCeO₃was developed, which then reacted with SrCO₃to form the final product Sr₂CeO₄, however, SrCO₃and CeO₂ converted directly to Sr₂CeO₄ at a lower temperature. The XRD results showed the crystal structure of Sr₂CeO₄ was orthorhombic. The emission spectra displayed a broad band with maximum at about 465 nm. The mechanical milling of starting power mixture and the sintering temperature had no effect on this emission spectra.     

Ca2-3xLa8+2x□x(SiO4)6O2的合成及其导电性能的研究

The silicate oxyapatites Ca_2-3xLa_8+2x□_x(SiO₄)₆O₂(x=0, 0.17, 0.33, 0.50, 0.67) was synthesized via a sol-gel method at low temperature. The apatite phases have been characterised by X-ray diffraction (XRD), conducting properties was studied by electrical chemistry impedance spectroscopy (EIS). The conductivity of La_9.33□_0.67(SiO₄)₆O₂ is 1.58×10^-3 S·cm^-1 at 700 ℃, it is higher about 4 270 times than that of Ca₂La₈(SiO₄)₆O₂, the activation energy is decreasing from 1.37 eV to 0.84 eV. With cation vacancies increasing,the conducting mechanism is gradually translation from a direct linear pathway free oxygen ion conduction to a curve pathway interstitial oxygen ion conduction. The electrical conductivities is almost independent of the oxygen partial pressure, this suggests that the oxyapatites exhibited almost pure O^2- ion conduction over a wide range of oxygen partial pressure.     

三元系RbCl-C2H5OH-H2O液固相平衡及其物化性质研究

The isothermal solubility and physico-chemical properties (density, refractive index) of ternary system RbCl-EtOH-H₂O at 25℃ and 50℃ have been firstly investigated by means of self-made micro-equilibrium and sampling apparatus .The compositions of liquid and solid at equilibrium state were determined, and the problem of analysis of ethanol content in system was properly solved. The phase diagram was drawn by the TPD phase-diagram computer program developed by us. Three empirical formulae were proposed to correlate the solubility, density and refractive index respectively. No demixing phenomena was observed in the range of temperature related in this study.     

纳米晶SnO2粉体的合成

Crystalline tin oxide nanoparticles were synthesized by the direct precipitation from the starting material granulated tin. TG-DTA of the precursor showed a heavy weight loss at about 130℃ accompanied by an endothermic peak， two exothermic peaks above 200℃ accompanied by small weight loss indicated the decomposition and the oxidation of residual NO₃^- ion and PEG. XRD showed that obtained particles agreed well with the determination result of bulk SnO₂. The broadened XRD patterns became sharper as the calcining temperature turned to higher， it was indicated that the growth of the particle was exhibited. The surface area of the particles calcined at 300℃ was 161.1m²·g^-1 and declined as the calcining temperature turned to higher. TEM showed an heavier agglomeration at higher temperature.     

电解质材料Sr-和Mg-掺杂LaGaO3的制备及性能研究

A dense La_0.8Sr_0.2Ga_0.83Mg_0.17O_2.815 electrolyte in pure perovskite phase was prepared by a polyacrylic acid assisted solid state reaction method, and the effects of La source on the structure and electrochemical performance were also studied. By means of XRD and SEM, the structure of this material was characterized, and the electrochemical properties were studied through AC impedance diagram. The results show that the sample presents a single perovskite-type phase after sintering at 1 450 ℃ and the relative density is 94%. The specimen has the lower activate energy and higher electrical conductivity at 600 ℃. There are two different activation energy at the turning point of 650 ℃, which are 74.6 and 42.4 kJ·mol^-1, respectively. The electrical conductivity is 0.057 S·cm^-1 and 0.017 S·cm^-1 at the temperature of 800 ℃ and 600 ℃, respectively.