ZrO2晶型对Ni/ZrO2催化剂CO甲烷化性能的影响

采用浸渍法制备了四方相ZrO2(t-ZrO2)和单斜相ZrO2(m-ZrO2)负载的Ni含量为10%的催化剂,在连续流动微反装置上考察了Ni/m-ZrO2以及不同温度焙烧Ni/t-ZrO2催化剂的CO甲烷化催化活性.采用N2物理吸附-脱附、H2-TPR、XRD、CO-TPSR及原位漫反射傅里叶变换红外光谱等技术对催化剂进行了表征.结果表明,在CO体积分数为1%,空速为20 000 h-1,常压的反应条件下,当CO转化率为50%时,Ni/m-ZrO2-673和Ni/t-ZrO2-673催化剂的反应温度分别为445 K和488 K,Ni/m-ZrO2-673催化剂的CO甲烷化活性远高于Ni/t-ZrO2-673催化剂.随焙烧温度的升高,Ni/t-ZrO2催化剂的CO甲烷化活性评价显著升高,产生这一现象的原因是在高温焙烧过程中Ni/t-ZrO2催化剂表面的t-ZrO2已转化为m-ZrO2,以m-ZrO2为载体的催化剂因m-ZrO2表面具有较多的配位不饱和O2-碱性中心和配位不饱和Zr4+-O2-位点而表现出高的CO甲烷化活性.     

负载型MoO3 /γ-Al2O3催化剂中晶格氧的丙烷氧化脱氢反应性能

采用X射线衍射(XRD),氢气程序升温还原(H2-TPR)和无氧脉冲反应评价等研究了MoO3在γ-Al2O3载体表面的分散状态和负载型MoO3/γ-Al2O3催化剂晶格氧物种的丙烷氧化脱氢反应性能.结果表明在γ-Al2O3表面MoO3分散容量的实测值(4.73Mo6 /nm2)与按照"嵌入模型"估算的理论分散容量(4.90 Mo6 /nm2)接近.在分散容量以下,键合在γ-Al2O3表面孤立的Mo-O-Al物种倾向于分散在相邻的空位上且通过Mo-O-Mo化学键相连形成聚合的表面MoOx物种.随着MoO3负载量增加,Mo-O-Al键合方式逐步转变为Mo-O-Mo键合方式,钼离子周围的氧离子活泼性下降,导致丙烷氧化脱氢反应活性下降.超过分散容量以上的Mo离子以晶相形式存在.由于钼离子表面利用率下降,尤其是多层的晶相氧化钼表面Mo-O-Mo物种难以与载体表面铝离子键合,导致与钼离子相结合的氧离子可移动性下降、反应活泼性降低,催化剂的丙烷氧化脱氢反应活性急剧下降.     

以ZrO_2-Al_2O_3为载体Co-Mo-K耐硫变换催化剂的TPR研究

利用程序升温还原 (TPR)技术 ,研究了ZrO2 对Co/Al2 O3、Mo/Al2 O3、Mo -K/Al2 O3以及Co -Mo -K耐硫变换催化剂氧化还原性能的影响。结果表明 ,ZrO2 的引入 ,使活性组分在载体表面分散的更好 ,促进了Mo -K活性相的形成 ,使Co和Mo的还原变得容易 ,并起到抑制催化剂在反应中被重新氧化的作用。     

制备方法对负载型纳米ZrO2/Al2O3复合载体性能的影响

采用浸渍-沉淀法制备了负载型纳米ZrO2/Al2O3复合载体.采用X射线衍射、N2物理吸附、差示扫描量热(DSC)和程序升温脱附等技术考察了浸渍方式和干燥方法对复合载体的表面性能、热稳定性和晶相结构的影响.结果表明,ZrO2/Al2O3复合载体中没有生成ZrO2-Al2O3复合氧化物或固溶体,纳米ZrO2仅负载在Al2O3的表面.微波干燥法制备的ZrO2/Al2O3复合载体的比表面积(158.7 m2/g)较大,最可几孔径为19.4 nm,ZrO2的粒度为4.2 nm,晶相结构为四方相ZrO2.微波诱导作用使ZrO2/Al2O3复合载体表面产生了新的酸碱中心,微波干燥法制备的ZrO2/Al2O3复合载体具有较强的热稳定性,在873~1 073 K范围内DSC曲线没有出现吸热峰,而其它干燥方法制备的复合载体在903~1 023 K范围内出现了较明显的吸热峰,表明复合载体表面的部分四方相ZrO2转变为单斜相ZrO2(m-ZrO2).对超声波处理过的复合载体进行微波干燥能进一步提高纳米ZrO2与Al2O3之间的相互作用,纳米粒子的粒度(3.4 nm)更小,分布更均匀,但没有改变ZrO2的晶相结构.     

ZrO2对CuO／γ—Al2O3催化剂CO氧化性能的影响

用流动反应法、TPR、TPO和TG等技术研究了ZrO2的改性和CuO负载量对Cuo／y－Al2O3催化剂的氧化性能及还原行为的影响．实验结果表明，在低负载量（wCuO=15%以下）时，ZrO2对γ-Al2O3的改性可明显提高CuO／γ-Al2O3催化剂的CO氧化活性．ZrO2的存在可增加活性铜物种在载体表面的富集和有效地促进CU2+物种的氧化还原循环，增加CuO催化剂表面上铜物种的可还原量，从而促进CuO催化剂的氧化活性．     

氧化铝对Pt-SO2-4/ZrO2-Al2O3固体酸催化剂结构与酸性的影响

 通过混捏法制备了Pt-SO2-4/ZrO2-Al2O3固体酸催化剂,考察了该催化剂在正构烷烃低温异构化反应中的催化稳定性. 采用X射线衍射、差热分析、X射线光电子能谱、核磁共振、N2吸附-脱附和微量热等表征技术,对氧化铝的作用机理进行了研究. 结果表明,氧化铝起到结构助催化剂作用,对四方相氧化锆具有稳定作用,并延迟了氧化锆的晶化,抑制了氧化锆的烧结,从而增大了催化剂的比表面积和孔容. XPS结果表明, Zr 3d峰向低结合能方向移动, Al 2p峰向高结合能方向移动,说明Al3+的电子向Zr4+偏移. 微量热结果表明氧化铝的引入提高了催化剂的酸量和酸强度. 27Al固体核磁共振结果表明, Pt-SO2-4/ZrO2-Al2O3中的六配位铝的结构发生了变化. 氧化铝的引入还可能有助于氧化锆晶格缺陷的形成,焙烧过程中Al3+迁移进入氧化锆晶格并同晶取代Zr4+形成氧缺陷位,这些氧缺陷位在 S=O 键诱导下显示强酸性.     

环己酮肟在改性氧化锆催化剂上的Beckmann重排反应Ⅴ.活化焙烧温度对B2O3/ZrO2催化剂的影响

 采用BET，XRD，TG－DTA，FT－IR，XPS和NH3－TPD等分析手段，研究了活化焙烧温度（500～800℃）对B2O3／ZrO2催化剂织构／结构、表面性质和环己酮肟气相重排反应的影响．催化剂活化焙烧温度升高促进了ZrO2向单斜晶相转化，同时活性组分氧化硼由以BO4为主要结构单元的物种转变为以BO3为基本结构单元的B2O3，导致催化剂比表面积、孔体积以及表面酸量减小，ZrO2与B2O3之间的相互作用减弱．700℃活化焙烧的催化剂表面拥有最大比例的中强酸中心，而且Beckmann反应的活性稳定性最高．这些结果表明，活化焙烧温度对B2O3／ZrO2催化剂上气相重排反应的影响主要是通过改变催化剂中B原子的配位状态和表面酸性实现的．     

Nb2O5在t-ZrO2表面的分散状态与Br(φ)nsted酸特征

以草酸铌为前驱物,四方相氧化锆(t-ZrO2)为载体,通过浸渍法制备不同负载量的Nb2O5/t-ZrO2催化剂.采用粉末X射线衍射(XRD)、激光拉曼光谱(LRS)、紫外-可见漫反射光谱(UV-Vis DRS)等技术对t-ZrO2表面Nb2O5分散状态进行表征;采用异丁烯(IB)与异丁醛(IBA)缩合生成2,5-二甲基-2,4-己二烯(DMHD)反应评价不同负载量的Nb2O5/t-ZrO2的催化性能,采用吡啶吸附红外(Py-IR)光谱表征催化剂Br(φ)nsted酸中心特征.结果表明,由XRD定量相分析方法测定的Nb2O5在t-ZrO2表面单层分散容量与“嵌入模型”预测值接近.Nb2O5/t-ZrO2表面Br(φ)nsted酸中心特征与Nb2O5聚集状态密切相关.     

MoO3和Nb2O5助剂对Pt/ZrO2催化剂上短链烷烃燃烧反应的不同促进作用

贵金属Pt催化剂具有高活性和热稳定性,广泛应用于催化挥发性有机物的完全氧化反应(燃烧反应).短链烷烃(甲烷、乙烷、丙烷等)化学性质稳定,是最难氧化的一类有机物,常用作考察燃烧反应催化剂性能的模型反应物.然而,目前报道的研究工作通常仅限于针对某一种烷烃底物的催化燃烧,系统考察催化剂以及助剂对不同短链烷烃的催化燃烧活性鲜有报道.在短链烷烃中,甲烷只有C–H键;而其它烷烃除了C–H键;还有C–C键.因此,研究催化剂对甲烷、乙烷和丙烷燃烧反应催化性能的差异性,对于认识催化剂上C–H键和C–C键的活化具有非常重要的意义.本文制备了MoO3或Nb2O5修饰的Pt/ZrO2催化剂并用于短链烷烃的燃烧反应.研究发现,MoO3助剂对甲烷燃烧有明显的抑制作用,但对乙烷,丙烷和正己烷燃烧反应具有促进作用,促进作用随着烷烃碳链的增长逐渐增加;Nb2O5助剂对甲烷、乙烷、丙烷和正己烷燃烧反应均具有促进作用,然而促进作用随着碳链的增长而逐渐减弱.MoO3和Nb2O5助剂的不同促进作用与助剂影响催化剂表面酸性以及Pt物种的氧化或还原态有关.NH3-TPD结果表明,MoO3助剂可以显著增加Pt/ZrO2催化剂表面强酸位点数量,而Nb2O5助剂可以显著增加Pt/ZrO2催化剂表面中强酸位点数量.HTEM结果表明,两种助剂的添加都不会明显改变Pt物种的颗粒尺寸.在Pt-Mo/ZrO2催化剂上,MoO3覆盖部分Pt物种形成丰富的Pt-MoO3界面,促进了金属Pt物种和强表面酸性位点的生成,提高了丙烷燃烧反应活性;Pt-Nb/ZrO2催化剂上载体表面的部分Nb2O5被Pt物种包覆,使得生成的表面Pt-Nb2O5界面低于Pt-Mo/ZrO2催化剂,但由于催化剂表面酸性位的提升,也促进了丙烷燃烧反应活性的提高.XPS结果表明,在甲烷燃烧反应中,Pt-Nb/ZrO2催化剂上Ptn+物种能够更加稳定地存在,这可能是Nb2O5助剂提高Pt-Nb/ZrO2催化剂上甲烷燃烧活性的关键.而Pt-Mo/ZrO2催化剂上Ptn+物种在甲烷反应中可以更容易地被还原,并且由于MoO3的包裹导致暴露的Pt位点数量降低,使催化剂催化甲烷燃烧的活性受到抑制.可见,MoO3助剂更有利于C–C键活化,而Nb2O5助剂更有利于高键能的C–H键活化.综上,本文系统性地研究MoO3助剂和Nb2O5助剂对Pt/ZrO2催化剂上不同短链烷烃的燃烧反应的影响,证实了两种助剂的促进作用与碳链长度的关系是截然不同的.     

氧化铝对Pt-SO4^2-／ZrO2-Al2O3固体酸催化剂结构与酸性的影响

通过混捏法制备了Pt-SO4^2-／ZrO2-Al2O3固体酸催化剂，考察了该催化剂在正构烷烃低温异构化反应中的催化稳定性．采用X射线衍射、差热分析、X射线光电子能谱、核磁共振、N2吸附-脱附和微量热等表征技术，对氧化铝的作用机理进行了研究．结果表明，氧化铝起到结构助催化剂作用，对四方相氧化锆具有稳定作用，并延迟了氧化锆的晶化，抑制了氧化锆的烧结，从而增大了催化剂的比表面积和孔容．XPS结果表明，Zr3d峰向低结合能方向移动，Al2p峰向高结合能方向移动，说明Al^3＋的电子向Zr^4＋偏移．微量热结果表明氧化铝的引入提高了催化剂的酸量和酸强度．^27Al固体核磁共振结果表明，Pt-SO4^2-／ZrO2-Al2O3中的六配位铝的结构发生了变化．氧化铝的引入还可能有助于氧化锆晶格缺陷的形成，焙烧过程中Al^3＋迁移进入氧化锆晶格并同晶取代Zr^4＋形成氧缺陷位，这些氧缺陷位在S=O键诱导下显示强酸性．     

Facile synthesis of pure monoclinic and tetragonal zirconia nanoparticles and their phase effects on the behavior of supported molybdena catalysts for methanol-selective oxidation

Pure monoclinic (m) and tetragonal (t) zirconia nanoparticles were readily synthesized from the reaction of inorganic zirconium salts (e.g., hydrated zirconyl nitrate) and urea in water and methanol, respectively, via a facile solvothermal method. The role of the solvents was crucial in the formation of the pure ZrO(2) phases, whereas their purity was essentially insensitive to other variables, including reaction temperature, reactant concentration, pH, and zirconium salts. Water as the solvent led to the transformation of hydrous ZrO(2) precipitates initially formed with tetragonal structures to thermodynamically more stable m-ZrO(2) via the dissolution-precipitation process, whereas methanol favored the removal of water molecules from the precursors via their reaction with urea, consequently maintaining the tetragonal structures. The obtained tetragonal samples were found to possess superior hydrothermal stability compared to those reported previously, which provides the possibility for systematically studying the effects of ZrO(2) phases on many catalytic reactions involving water as a reactant or product. Using these pure m- and t-ZrO(2) phases as supports, dispersed MoO(x) catalysts were synthesized at MoO(x) surface densities of approximately 5.0 Mo/nm(2), which is close to one monolayer of coverage. Characterization by X-ray diffraction and Raman spectroscopy confirmed that the pure ZrO(2) phases remained unchanged in the presence of the MoO(x) domains and the MoO(x) domains existed preferentially as 2D polymolybdate structures. The catalysts were subsequently examined for selective methanol oxidation as a test reaction. m-ZrO(2) support led to 2-fold greater oxidation rates than for t-ZrO(2) support, reflecting the higher intrinsic reactivity of the MoO(x) domains on m-ZrO(2). This is consistent with their higher reducibility probed by temperature-programmed reduction with H(2) (H(2) TPR). These observed effects of the ZrO(2) phases provide the basis for designing catalysts with tunable redox properties and reactivity.     

多级孔结构WO3/ZrO2固体酸催化剂的烷基化催化性能研究

采用复合模板表面活性剂辅助水热法一步合成WO3/ZrO2体系多级孔固体酸催化剂,探讨了煅烧温度对所合成催化剂试样酸强度及酸量的影响,并考察了催化剂针对苯和十二烯的烷基化反应中的催化性能.结果表明,WO3/ZrO2体系催化剂具有较强的酸强度,并且与催化剂的比表面积和晶化程度有密切关系,比表面积的增大和四方相ZrO2的生成能有效地提高催化剂的酸强度.该催化剂具有优良的烷基化反应催化活性和选择性,其中450℃,5h煅烧的WO3/ZrO2催化剂样品酸性最强,其烷基化催化活性和选择性最优.     

锆改性钴基费-托合成催化剂催化性能的研究

 考察了助剂锆和金属钴负载量对锆改性Co／Al2O3催化剂催化性能的影响．结果表明，锆助剂能够高度分散在氧化铝载体上，而活性组分钴以一定尺寸存在；锆的添加能够明显地提高Co／Al2O3催化剂的催化活性和C5＋烃选择性，但助剂锆含量对催化剂催化性能的影响不大；在锆存在下，催化剂的催化活性随金属钴含量先升高后降低．进一步的研究表明，催化剂上烃形成速率的提高可能是由于锆助剂能够增加催化剂的活性位数目，增强桥式CO吸附的强度，在Co－ZrO2间形成界面．     

Preparation and Characterization of Modified-ZrO2 Catalysts for the Reaction of Co Hydrogenation

ZrO2 in different structures and CexZr4-xO8 solid solutions have been prepared by a sol-gel related method with propionic acid as the solvent.The results of their characterization and CO hydrogenation performance eveluation show that ｔ-ZrO2 has better catalytic performance for CO hydrogenation to hydrocarbon than ｍ-ZrO2.Cerium(Ⅲ）acetate and zirconium (Ⅵ）acetylacetonate have been chosen as the most suitable starting materials for CexZr4-xO8 solid solution preparation.Ce-Zr reducibility properties are increased by the incorporation of zirconium oxide in the ceria structure.Ce2Zr2O8 exhibits a higher activity,lower methane selectivity and higher iso-C4 selectivity than tetragonal ZrO2.This implies that the formation mechanism of C4 hydrocarbons,especially that for the iso-C4 fraction is different over Ce2Zr2O8 and t-ZrO2.     

Selective Oxidation of Methane to Methanol Using Molecular Oxygen on MoOx／（LaCoO3＋Co3O4） Catalysts

Comparatively high CH3OH selectivity (60.0%) and yield (6.7%) were obtained on MoOx/(LaCoO3 Co3O4) catalysts in selective oxidation of methane to methanol using molecular oxygen as oxidant. The interaction between MoOx and La-Co-oxide modified the molecular structure of molybdenum oxide and the ratio of O^-/O^2- on the catalyst surface, which controlled the catalytic performance of MoOx/(LaCoO3 Co3O4) catalysts.     

纯四方相硫化氧化锆催化剂的制备及其生物柴油合成应用研究

将过硫酸铵浸渍于直接合成的纳米氧化锆晶体表面,经300-500℃高温焙烧处理获得硫化氧化锆催化剂。采用X射线衍射（XRD）、氮气吸附-脱附、氨气程序升温脱附（NH₃-TPD）、傅里叶红外光谱（FT-IR）、扫描电镜（SEM）和能谱仪（EDS）等分析手段对催化剂的结构性能进行了表征。结果表明,所有的催化剂均展现出纯四方相结构和高的结晶度。其中,经500℃热处理获得的催化剂拥有最高的硫含量和酸性位,将其应用于大豆油与甲醇酯交换反应合成生物柴油,获得了脂肪酸甲酯收率高达84.6%的催化效果,进一步表明该催化剂表面存在优越的超强酸位。     

费-托合成Co/ZrO2-Al2O3催化剂反应性能的研究

以ZrOCl2·6H2O和AlCl3为原料,采用共沉淀方法制得一系列不同ZrO2质量分数的ZrO2-Al2O3混合氧化物载体;并以该混合氧化物为载体,采用初湿浸渍法制得钴质量分数为12％的Co/ZrO2-Al2O3催化剂。XRD、NH3-TPD、TPR和原位IR等表征结果表明,随着混合载体中ZrO2质量分数的增加,载体比表面积先增加后减少,混合载体的平均孔径则小于单一氧化物ZrO2和Al2O3的平均孔径。ZrO2和Al2O3载体混合后会导致氧化物的比表面积和酸性增大并且有新的物相生成。当混合氧化物用作载体时,能够抑制载体表面金属钴的分散,改变催化剂的还原行为,降低催化剂对CO物种的吸附能力。CO加氢反应表明,与单一金属氧化物相比,钴负载ZrO2-Al2O3混合氧化物催化剂的加氢活性和重质烃选择性有所降低。     

Modeling of the adsorption and desorption of CO2 on Cu/ZrO2 and ZrO2 catalysts

The interaction between carbon dioxide and two zirconia catalysts-a Cu/ZrO2 catalyst containing 34% copper and a pure ZrO2 catalyst-was studied by pulse adsorption and temperature-programmed desorption methods. Kinetic modeling by nonlinear regression was applied to acquire information on the adsorption and desorption of CO2 relevant in the synthesis of methanol from carbon dioxide. A model that included three types of adsorption sites described well the experimental data for both Cu/ZrO2 and ZrO2. The model assumed first-order kinetics and a Freundlich-type logarithmic dependence of adsorption enthalpy on surface coverage. The parameters of the model were well identified and were in the physically meaningful range. The results indicate that, at 30 degrees C, on both catalysts, carbon dioxide adsorbs reversibly on one type of site and irreversibly on two other types of sites.     

Fourier transform infrared spectroscopic study of surface acidity by pyridine adsorption on Mo/ZrO2-SiO2(Al2O3) catalysts

Acidity of the oxidic molybdenum catalysts supported on mixed ZrO2-SiO2 and ZrO2-Al2O3 carriers was investigated by Fourier transform infrared spectroscopy of pyridine adsorption. Deposition of molybdenum on ZrO2-SiO2 and ZrO2-Al2O3 supports leads to formation of surface Br?nsted acid sites. The number of the Br?nsted and Lewis acid sites in supported-molybdenum catalysts depends on both the ZrO2 content and the type of the support. With increasing ZrO2 content, the Lewis acid sites increase for both series of catalysts. The Br?nsted acid sites are higher for Mo/ZrO2-SiO2 samples compared to those for Mo/ZrO2-Al2O3 and also increase with zirconia.     

Structures and properties of zirconia-supported ruthenium oxide catalysts for the selective oxidation of methanol to methyl formate

The effects of RuO(x) structure on the selective oxidation of methanol to methyl formate (MF) at low temperatures were examined on ZrO(2)-supported RuO(x) catalysts with a range of Ru surface densities (0.2-3.8 Ru/nm(2)). Their structure was characterized using complementary methods (X-ray diffraction, Raman and X-ray photoelectron spectra, and reduction dynamics). The structure and reactivity of RuO(x) species change markedly with Ru surface density. RuO(x) existed preferentially as RuO(4)(2-) species below 0.4 Ru/nm(2), probably as isolated Zr(RuO(4))(2) interacting with ZrO(2) surfaces. At higher surface densities, highly dispersed RuO(2) domains coexisted with RuO(4)(2-) and ultimately formed small clusters and became the prevalent form of RuO(x) above 1.9 Ru/nm(2). CH(3)OH oxidation rates per Ru atom and per exposed Ru atom (turnover rates) decreased with increasing Ru surface density. This behavior reflects a decrease in intrinsic reactivity as RuO(x) evolved from RuO(4)(2-) to RuO(2), a conclusion confirmed by transient anaerobic reactions of CH(3)OH and by an excellent correlation between reaction rates and the number of RuO(4)(2-) species in RuO(x)/ZrO(2) catalysts. The high intrinsic reactivity of RuO(4)(2-) structures reflects their higher reducibility, which favors the reduction process required for the kinetically relevant C-H bond activation step in redox cycles using lattice oxygen atoms involved in CH(3)OH oxidation catalysis. These more reactive RuO(4)(2-) species and the more exposed ZrO(2) surfaces on samples with low Ru surface density led to high MF selectivities (e.g. approximately 96% at 0.2 Ru/nm(2)). These findings provide guidance for the design of more effective catalysts for the oxidation of alkanes, alkenes, and alcohols by the synthesis of denser Zr(RuO(4))(2) monolayers on ZrO(2) and other high surface area supports.