Sulfur speciation by capillary zone electrophoresis: conditions for sulfite stabilization and determination in the presence of sulfate, thiosulfate and peroxodisulfate

Capillary zone electrophoresis (CZE) was used for the separation of the sulfur species SO₃ ^2–, SO₄ ^2–, S₂O₃ ^2– and S₂O₈ ^2–. Using an electrolyte system with 9.5 mmol L^–1 potassium chromate as UV-absorbing probe and 1 mmol L^–1 diethylenetriamine (DETA) as electroosmotic flow modifier, various possibilities for the stabilization of sulfite and electrophoretic separation of the sulfur anions were investigated. By adding 5% propanol as a stabilizer to both the working electrolyte and the sample solution, a good stabilization for sulfite and a separation of the sulfur anions in a short analysis time (4 min) was achieved. The advantages by using propanol instead of other stabilizers often used in analytical techniques are discussed. The electrophoretic separation of the sulfur anions was optimized with respect to the pH of the working electrolyte and concentration of the electroosmotic flow modifier (DETA). The detection limits achieved for SO₃ ^2–, SO₄ ^2–, S₂O₃ ^2– and S₂O₈ ^2– were 0.35, 0.25, 0.78 and 0.80 mg L^–1, respectively. Received: 16 December 1999 / Revised: 7 March 2000 / Accepted: 14 March 2000     

Capillary electrophoretic determination of thiosulfate and its oxidation products

Capillary electrophoresis (CE) was developed for the rapid and simple determination of thiosulfate and its oxidation products such as common polythionates, sulfite and sulfate. Direct and indirect UV detection techniques were investigated. The optimized separations of UV absorbing S2O3(2-), S4O6(2-), S5O6(2-) and S6O6(2-) anions were carried out in 5 mmol l(-1) (NH4)2SO4, 5 mmol l(-1) KH2PO4 electrolyte at pH 5.0, with direct UV detection at 214 nm. All analytes were well resolved in less than 4 min. Analysis of S2O3(2-), S4O6(2-), SO4(2-) and SO3(2-) ions can be performed in 5 mmol l(-1) H2CrO4, 1 mmol l(-1) hexamethonium hydroxide electrolyte neutralized with triethanolamine to pH 8.0, using indirect UV detection at 254 nm. However, the detection sensitivity for tetrathionate was poor. Other polythionates can not be detected at all because of their high absorbance even at 254 nm. The developed CE method was applied for the monitoring of sulfur species in spent fixing solutions during the electrolytic oxidation.     

有机酸与无机阴离子的梯度离子色谱法分析研究

研究了用离子色谱法梯度洗脱抑制电导检测器分析有机酸与无机阴离子的色谱条件,建立了最佳梯度程序。用阴离子交换分离,选用去离子水、氢氧化钠和甲醇作淋洗液,分别对５种二元有机酸和３种无机阴离子做二元梯度淋洗,对１０种多元有机酸和３种无机阴离子做三元梯度淋洗。方法用于果汁饮料与柠檬酸发酵液的测定,结果令人满意。     

Capillary electrophoretic determination of thiosulfate,sulfide and sulfite using in-capillary derivatization with iodine

A new capillary electrophoresis (CE) method was developed for the rapid, simple and selective determination of thiosulfate, sulfide and sulfite species. The proposed method is based on the in-capillary derivatization of separated sulfur anions by mixing their zones with the iodine zone during the electrophoretic migration and direct UV detection of iodide formed. The optimal conditions for the separation and derivatization reaction were established by varying electrolyte pH, electrolyte counter-ion, concentration of iodine, and applied voltage. The optimized separations were carried out in 20 mmol/L Tris-chloride electrolyte (pH 8.5) using direct UV detection at 214 nm. All three sulfur species were well resolved in less than 4 min. The method gives repeatability comparable or even better than this obtained for sulfur anions using standard CE technique. The proposed CE system was applied to the monitoring of sulfur anions in spent fixing solutions during the electrolytic oxidation.     

茶叶中无机阴离子的毛细管电泳分离间接检测方法的研究

建立了毛细管电泳分离测定茶叶中Cl-、NO2-、NO3-、SO42-、F-及HPO24-的方法。通过研究分离电压、背景电解质和电渗流改性剂的浓度、pH的影响优化了分析条件。在优化条件下,6种无机阴离子在10min内得到完全分离,各组分迁移时间和峰高的相对标准偏差(RSD)分别为1.9%~4.7%和1.2%~3.8%,检出限为0.11~0.82 mg/L。通过分析实际样品并做加标回收实验验证了该方法的可行性,Cl-、NO3-、SO42-及HPO24-的回收率为93%~98%。     

毛细管区带电泳技术快速分离检测爆炸残留物中的无机离子

利用间接紫外毛细管区带电泳方法完成了对爆炸残留物中7种无机离子(K+,NH+4,NO-2,NO-3,SO2-4,ClO-3,ClO-4)的分离检测。阳离子测定采用的缓冲体系为10 mmol/L吡啶（pH 4.5）-3 mmol/L冠醚,K+和NH+4在2.6 min内达到基线分离,检出限分别为0.25 mg/L和0.10 mg/L(S/N=3)。阴离子测定采用的缓冲体系为40 mmol/L硼酸-1.8 mmol/L重铬酸钾-2 mmol/L硼酸钠（pH 8.6）,氢氧化四甲铵为电渗流改性剂,5种阴离子在4.6 min内达到基线分离,检出限为0.10～1.85 mg/L。该方法已成功地应用于实际爆炸物样品种类的判定分析,取得了很好的结果。     

Determination of inorganic anions in Kraft pulping liquors by capillary electrophoresis

Various sulfur containing anions (sulfate, sulfite, and thiosulfate) in Kraft pulping process liquors are determined by capillary electrophoresis. In addition, other inorganic anions (hydroxide, chloride, oxalate, carbonate) are analyzed with the developed method. Through optimization of the separation conditions it is possible to simultaneously determine these anionic species in pulping liquors with direct and indirect UV detection at 185, 214, and 254 nm. To ensure short separation times a migration of the anionic analytes in the same direction as the electroosmotic flow (co-electroosmotic CE) is established by reversal of the electroosmotic flow with 1,5-dimethyl-1,5-diazaundecamethylene polymethobromide (hexadimethrine bromide; HDB; polybrene™) which is added to the electrolyte as EOF modifier. The impact of acetonitrile as organic modifier to improve the selectivity of the anionic analytes is also investigated. The developed method is then applied to analyze and quantify various anions in pulping liquors (white and black liquors). By simultaneously determining the hydroxide concentration it is possible to calculate effective alkalinity and sulfidity with the measured concentrations without the need of volumetric methods.     

毛细管区带电泳技术快速分离检测爆炸残留物中的无机离子

利用间接紫外毛细管区带电泳方法完成了对爆炸残留物中7种无机离子(K+,NH+4,NO-2,NO-3,SO2-4,ClO-3,ClO-4)的分离检测。阳离子测定采用的缓冲体系为10 mmol/L吡啶（pH 4.5）-3 mmol/L冠醚,K+和NH+4在2.6 min内达到基线分离,检出限分别为0.25 mg/L和0.10 mg/L(S/N=3)。阴离子测定采用的缓冲体系为40 mmol/L硼酸-1.8 mmol/L重铬酸钾-2 mmol/L硼酸钠（pH 8.6）,氢氧化四甲铵为电渗流改性剂,5种阴离子在4.6 min内达到基线分离,检出限为0.10～1.85 mg/L。该方法已成功地应用于实际爆炸物样品种类的判定分析,取得了很好的结果。     

毛细管电泳法测定阿霉素脂质体药物中的微量硫酸根离子

建立了以硝酸钾作为背景电解质测定阿霉素脂质体药物中微量硫酸根离子的毛细管电泳分析法。考察了分离电压、背景电解质、电渗流改性剂浓度、pH值对分离测定的影响。结果表明,当毛细管长度为60 cm(有效长度51.5 cm)、分离电压为~15 kV、缓冲溶液采用20 mmol/L硝酸钾(pH 7.0)、电渗流改性剂采用0.4 mmol/L十六烷基三甲基氯化铵(CTAC)、检测波长为202 nm时,阿霉素脂质体破乳液中硫酸根离子和氯离子在3 min内得到了基线分离,硫酸根离子迁移时间和峰面积的相对标准偏差分别小于0.01%和1.0%,检出限为5 μg/L。用该方法对阿霉素脂质体样品中的微量硫酸根离子进行了分析测定,结果令人满意。     

电解质溶液组成对低分子量阴离子毛细管电泳分离的影响

研究了毛细管电泳间接紫外检测法测定低分子量阴离子时电解质溶液中背景电解质、电渗流改性剂、ｐＨ值、有机溶剂等对分离的影响；比较了铬酸根、邻苯二甲酸根、苯甲酸根３种背景离子对不同迁移率阴离子分离的影响，并对间接紫外检测的定量基础及灵敏度进行了讨论；考察了３种不同长链烷基三甲基季铵盐电渗流改性剂浓度对阴离子迁移时间和电渗迁移率的影响，结果表明电渗流的改性效果与烷基链的长度有关；ｐＨ影响阴离子的有效迁移率     

Capillary electrophoretic determination of sulfite using the zone-passing technique of in-capillary derivatization.

A new capillary electrophoretic (CE) method was developed for the simple and selective determination of sulfite. The proposed method is based on the in-capillary derivatization of sulfite with iodine using the zone-passing technique and direct UV detection of iodide formed. The optimal conditions for the separation and derivatization reaction were established by varying concentration of iodine, electrolyte pH and applied voltage. The optimised separations were carried out in 20 mmol l(-1) Tris-HCl electrolyte (pH 8.5) using direct UV detection at 214 nm. Experimental results showed that the injection of the iodine zone from anodic end of the capillary gives significantly better precision. Common UV absorbing anions such as Br-, l-, S2O3(2-), NO3-, NO2-, SCN- did not give any interferences. Valid calibration (r2=0.998) is demonstrated in the range 1 x 10(-5) - 8 x 10(-4) mol l(-1) of sulfite. The detection limit (SIN=3) was 2 x 10(-6) mol l(-1). The proposed system was applied to the determination of free sulfite in wines. The recovery tests established for wine samples were within the range 92-103%. The CE results were compared with those obtained by iodometric titration technique.     

Modification of the electroosmotic flow and separation selectivity of anions in electrochromatography with pseudo-stationary phases of C14-alkyldimethylammoniopropane sulfonate zwitterionic surfactants by addition of salts to the background electrolyte

The effects of salts (NaCl, NaClO4, MgCl2, CeCl3) added to background electrolyte (BGE) solutions (10 mmol L(-1) sodium phosphate, pH 7.2) on electroosmotic flow (EOF) and the separation selectivity of anions (chloride, bromide, iodide, nitrite, nitrate, chlorate, thiocyanate, iodate, chromate, and molybdate ion) by capillary electrochromatography using the zwitterionic surfactant 3-(N,N-dimethylmyristylammonio)propane sulfonate (C14N3S) as a pseudo-stationary phase were investigated. There are two mechanisms affecting the separations: 1. the cations and anions of the added salts interact with the zwitterionic surfactant to varying degrees, thus changing the overall retention of the analytes; and 2. they change the EOF and the resulting apparent mobilities. It was shown that a BGE containing perchlorate and a low concentration of zwitterionic surfactant (2 mmol L(-1)) gave a stable and reproducible EOF and the concentration of perchlorate could be used to manipulate the separation selectivity for polarizable anions, such as iodide and thiocyanate. These effects are discussed in terms of measured association constants describing the interaction of anions and cations with the zwitterion.     

聚合离子液体为添加剂的毛细管电泳法用于快速高效分离饮料中7种有机酸

用一种聚合离子液体(聚1-乙烯基-3-丁基咪唑溴盐)为添加剂,以毛细管电泳法(CE)快速直接分离饮料中7种有机酸(丙二酸、酒石酸、抗坏血酸、反丁烯二酸、苯甲酸、山梨酸和柠檬酸)。详细考察了几种影响分离效果的条件,最佳背景电解质条件是125 mmol/L磷酸二氢钠缓冲液(pH 6.5)添加0.01 g/L聚合离子液体。7种分析物在4 min内能够快速高效分离(105000~636000 塔板/m),迁移时间的标准偏差(n=3)都不大于0.0213 min。7种分析物的检出限（以信噪比为3计）在0.001与0.05 g/L之间。这种方法被应用于一种美年达葡萄汁饮料中的有机酸检测。柠檬酸钠、苯甲酸和山梨酸被检测出,含量分别是2.64、0.10和0.08 g/L,其加标回收率分别为100.3%、100.7%和131.7%。该方法简单、快速、低廉,可以用作食品中有机酸添加剂的检测。     

Determination of organic anions in waste liquid of sodium hydrosulfite production by ion chromatography.

An ion chromatographic method for simultaneous determination of formate, hydroxyethyl sulfonate (HES), hydroxyethyl thiosulfate (HET), and coexisting anions in the industrial waste liquid of sodium hydrosulfite production was developed. The mixture of 1.6 mmol/l of phthalic acid and 1.2 mmol/l tri-(hydroxyethyl) aminomethane was used as eluent. The interference of coexisting sulfite anion with HES was avoided by selective oxidation with hydrogen peroxide as oxidizer. The other coexisting inorganic anions, Cl-, SO4(2-) and S2O3(2-) can be determined simultaneously. The linear range of the peak area calibration curves for all analytes was up to two or three orders of magnitude. The detection limits (S/N = 3) for formate, HES and HET were 2.4, 1.0 and 0.5 mg/l, respectively. The recoveries for all analytes were 91.61-100.6%.     

硫代硫酸盐浸金过程中连多硫酸根的高效毛细管电泳法分析

采用高效毛细管电泳对硫代硫酸盐提金浸出液中的S3O62-和S4O62-进行分析研究,对缓冲溶液,电压、和检测波长对分析的影响进行了探讨。适宜的分离条件为:5 mmol/L(NH4)2SO4、5 mmol/L NaH2PO4,pH 6的缓冲溶液;重力进样5s,电压-20kV,波长214nm,有效长度为30 cm。在0.1～6 mmol/L和0.05～4mmol/L范围内S3O62-和S4O62-浓度与峰面积呈线性关系,在此进样条件下,S3O62-与S4O62-浓度高于80与50 mmol/L时信噪比大于2。实际浸金液用缓冲溶液稀释100倍后,S3O62-与S4O62-可实现基线分离,其它离子几乎不干扰检测。     

Separation of arsenic species by capillary electrophoresis with sample-stacking techniques

A simple capillary zone electrophoresis procedure was developed for the separation of arsenic species (AsO(2)(2-), AsO(4)(2-), and dimethylarsinic acid, DMA). Both counter-electroosmotic and co-electroosmotic (EOF) modes were investigated for the separation of arsenic species with direct UV detection at 185 nm using 20 mmol L(-1) sodium phosphate as the electrolyte. The separation selectivity mainly depends on the separation modes and electrolyte pH. Inorganic anions (Cl(-), NO(2)(-), NO(3)(-) and SO(4)(2-)) presented in real samples did not interfere with arsenic speciation in either separation mode. To improve the detection limits, sample-stacking techniques, including large-volume sample stacking (LVSS) and field-amplified sample injection (FASI), were investigated for the preconcentration of As species in co-CZE mode. Less than 1 micromol L(-1) of detection limits for As species were achieved using FASI. The proposed method was demonstrated for the separation and detection of As species in water.     

毛细管电泳对微生物代谢中硫酸根和硫代硫酸根的分离与测定

建立了微生物代谢中硫酸根和硫代硫酸根的毛细管电泳分析方法．在选定实验条件下，各种阴离子（Ｓ２Ｏ２－３、ＳＯ２－４、ＣＩ－、ＮＯ－３、ＰＯ３－４）在４ ｍｉｎ内达到完全分离，其中 Ｓ２Ｏ２－３和ＳＯ２－４迁移时间的相对标准偏差小于１％，峰面积的相对标准偏差小于５％．测定了４种菌株分别在两种培养基中的Ｓ２Ｏ２－３和ＳＯ２－４浓度随培养时间的变化．结果表明，其中一菌株在ＳＫ基中对Ｓ２Ｏ２－３有明显的氧化作用．     

Adsorption of sulfur dioxide on hematite and goethite particle surfaces

The adsorption of sulfur dioxide (SO(2)) on iron oxide particle surfaces at 296 K has been investigated using X-ray photoelectron spectroscopy (XPS). A custom-designed XPS ultra-high vacuum chamber was coupled to an environmental reaction chamber so that the effects of adsorbed water and molecular oxygen on the reaction of SO(2) with iron oxide surfaces could be followed at atmospherically relevant pressures. In the absence of H(2)O and O(2), exposure of hematite (alpha-Fe(2)O(3)) and goethite (alpha-FeOOH) to SO(2) resulted predominantly in the formation of adsorbed sulfite (SO(3)(2-)), although evidence for adsorbed sulfate (SO(4)(2-)) was also found. At saturation, the coverage of adsorbed sulfur species was the same on both alpha-Fe(2)O(3) and alpha-FeOOH as determined from the S2p : Fe2p ratio. Equivalent saturation coverages and product ratios of sulfite to sulfate were observed on these oxide surfaces in the presence of water vapor at pressures between 6 and 18 Torr, corresponding to 28 to 85% relative humidity (RH), suggesting that water had no effect on the adsorption of SO(2). In contrast, molecular oxygen substantially influenced the interactions of SO(2) with iron oxide surfaces, albeit to a much larger extent on alpha-Fe(2)O(3) relative to alpha-FeOOH. For alpha-Fe(2)O(3), adsorption of SO(2) in the presence of molecular oxygen resulted in the quantitative formation of SO(4)(2-) with no detectable SO(3)(2-). Furthermore, molecular oxygen significantly enhanced the extent of SO(2) uptake on alpha-Fe(2)O(3), as indicated by the greater than two-fold increase in the S2p : Fe2p ratio. Although SO(2) uptake is still enhanced on alpha-Fe(2)O(3) in the presence of molecular oxygen and water, the enhancement factor decreases with increasing RH. In the case of alpha-FeOOH, there is an increase in the amount of SO(4)(2-) in the presence of molecular oxygen, however, the predominant surface species remained SO(3)(2-) and there is no enhancement in SO(2) uptake as measured by the S2p : Fe2p ratio. A mechanism involving molecular oxygen activation on oxygen vacancy sites is proposed as a possible explanation for the non-photochemical oxidation of sulfur dioxide on iron oxide surfaces. The concentration of these sites depends on the exact environmental conditions of RH.     

Parameters influencing separation and detection of anions by capillary electrophoresis

Electrolyte composition is critical in optimizing separation and detection of ions by capillary electrophoresis. The parameters which must be considered when designing an electrolyte system for capillary electrophoresis include electrophoretic mobility of electrolyte constituents and analytes, detection mode, and compatibility of electrolyte constituents with one another. An electrolyte system based on pyromellitic acid is well suited for use with indirect photometric detection, and provides excellent separations of anions. The ability to modify the electrophoretic mobility of pyromellitic acid as a function of ph provides flexibility in matching electrophoretic mobilities of analytes. Additionally, the use of alkyl amines as electroosmotic flow modifiers allows the rapid separation of anions by reversing the direction of electroosmotic flow in a fused-silica capillary. The optimization of a capillary electrophoresis electrolyte for anion analysis is also discussed in terms of pH, ionic strength and applied voltage. The effect of organic solvent on separation selectivity is also discussed.     

Capillary electrophoretic method for the determination of inorganic and organic anions in real samples. Strategies for improving repeatability and reproducibility

Selectivity and robustness of the pyromellitic acid (PMA) based background electrolyte was improved in order to increase its applicability for routine analysis of inorganic and organic anions in real samples. An electrolyte composed of 6.75 mM PMA, 0.5 mM hexamethonium hydroxide as electroosmotic flow (EOF) modifier, Ca(2+) 0.05 mM as complexation agent and pH adjusted to 7.6 with TEA 1M allows for the separation of 22 inorganic and organic anions in less than 17 min. Good RSDs for within-day migration time reproducibility (0.03-0.9%) and day-to-day analyses (0.04-1.4%) were obtained by the use of two internal standards, allowing for an accurate compound identification. The detection limits ranged from 0.1 to 0.4 mgL(-1) (S/N=3) for hydrodynamic injection (1250 mbars). The applicability of the proposed method was demonstrated by the analysis of inorganic and organic anions in diverse real samples. The recoveries obtained ranged from 93 to 106%.