对甲氧基苯辛基二甲基烯丙基氯化铵与丙烯酰胺共聚动力学研究

采用定时取样研究了以过硫酸钾-亚硫酸氢钠为引发剂,对甲氧基苯辛基二甲基烯丙基氯化铵(ADMAAC)和丙烯酰胺(AM)在水溶液中的共聚反应动力学,测定了相应的聚合速率方程、聚合表观活化能;采用阴阳离子相互作用测定残余ADMAAC的含量,紫外分光光度法测定残余AM的含量,根据单体投料量和残余量差值,得到低转化率下共聚物的组成,按Kelem-Tudos法得到两单体竞聚率。实验结果表明:聚合反应温度在40℃下,聚合速率方程为:Rp=K[M]1.241[KPS]0.52[SHS]0.55;根据Arrhenius经验公式计算出对甲氧基苯辛基二甲基烯丙基氯化铵(ADMAAC)和丙烯酰胺(AM)共聚的表观活化能为73.85kJ/mol,高于AM水溶液均聚合的活化能Ea(70.32kJ/mol);两种单体的竞聚率为rADMAAC=0.197、rAM=4.503,为ADMAAC-AM共聚合反应控制确定了重要的动力学参数。两单体的竞聚率的积小于1,ADMAAC与AM共聚合行为类型是一种无恒比点的非理想共聚行为,共聚物组成曲线,在对角线下方。     

钛硅分子筛TS-1催化氯丙烯环氧化反应动力学研究

 摘要：研究了钛硅分子筛催化氯丙烯环氧化反应的条件及动力学行为．\r\n结果表明，以钛硅分子筛为催化剂，氯丙烯可被高选择性地氧化为环氧\r\n氯丙烷．环氧化反应速度与分子筛中骨架钛的含量及分子筛的用量呈正\r\n比关系，是一级反应．对于氧化剂H2O2，只有当c（H2O2）＜0．4mol／\r\nL时，环氧化反应为一级反应；而c（H2O2）＞1．0mol／L时，为零级反\r\n应．对于氯丙烯，随着其浓度的变化，环氧化反应的级数在1和0之间．\r\n然而，只有当氯丙烯浓度很高时，环氧化反应的级数才有明显的降低．\r\n根据实验结果和Eley－Rideal单分子吸附方程，提出了氯丙烯环氧化反\r\n应的动力学模型．\r\n关键词：钛硅分子筛，氯丙烯，过氧化氢，环氧化，环氧氯丙烷，反应\r\n动力学     

烯丙基氯氧化制环氧氯丙烷的研究进展

环氧氯丙烷是一种重要的有机化工原料和中间体。本文综述了以H2O2为氧源的烯丙基氯直接环氧化制备环氧氯丙烷的研究进展。分别介绍了以TS-1、Ti-MWW和磷钨杂多酸盐为催化剂的不同催化体系用于烯丙基氯环氧化反应的研究现状,阐述了各种不同催化体系的优缺点和未来的发展方向。     

Kinetics of Formation and Curing of Oligoether Urethane Allyl Ester

Kinetic parameters of formation of P-9AD oligoether urethane allyl ester with terminal double bonds and of its curing with dinitrile oxide were determined. The dependence of the rate constant on the allyl alcohol concentration and temperature was studied. The mechanism of reaction of P-9A prepolymer with allyl alcohol was proposed. The kinetic and thermodynamic parameters of curing of oligoether urethane allyl ester with dinitrile oxide were determined. The mechanism of reaction of P-9AD oligoether urethane allyl ester with dinitrile oxide was proposed.     

Ti-MWW催化氯丙烯环氧化固定床工艺研究

以Ti-MWW分子筛为催化剂,H2O2为氧化剂,研究了氯丙烯环氧化制环氧氯丙烷固定床工艺过程的反应规律.结果表明,H2O2的空速对该反应过程起着非常重要的作用.优化的反应参数为:以乙腈为溶剂,氯丙烯/H2O2摩尔比为5,反应温度为333K,H2O2空速为0.44h-1.在该条件下氯丙烯转化率、环氧氯丙烷选择性、H2O2转化率及有效利用率分别达到19.0%,99.9%,98.0%和97.0%。     

飞秒脉冲作用下氯丙烯的多光子解离和电离动力学

The dissociation and photoionization dynamics of C₃H₅Cl were studied at 200, 400, and 800 nm with femtosecond laser pulses. The time-of-flight mass spectra, laser power index and photoelectron images were recorded. At short wavelength (200 nm), ionization of the parent molecule was found to be the dominant channel, while other ions were generated by the dissociation of C₃H₅Cl⁺. With the shift to long wavelength (e.g., 800 nm), fragment ions became dominant, and were generated through the multiphoton ionization of neutral fragments after the photodissociation of C₃H₅Cl. These results imply that photodissociation plays a significant role at long wavelength, because neutral fragments are supposed to be generated from the intermediate states reached by 800 nm photons. At 400 nm, the dissociation on the intermediate states is also critical, but is not as high as that at 800 nm. Taken together, our results demonstrate that the dissociation/ionization behaviors of allyl chloride are wavelength-dependent, and reveal the complex dynamics of allyl chloride at 200, 400 and 800 nm.     

等级孔介孔-微孔TS-1分子筛单晶的合成及催化氯丙烯环氧化性能

针对当前钛硅型分子筛存在的微孔孔道孔径限制导致的流通扩散性能差及催化效率低等关键瓶颈问题, 通过在微孔分子筛中构筑跨尺度贯通高物质传输性能的等级孔道结构, 对钛硅分子筛(TS-1)晶体内等级孔道结构的可控构筑及其催化环氧化进行了研究, 成功制备出具有富含介孔孔道的等级孔介孔-微孔TS-1分子筛单晶材料(HTS-1), 其在氯丙烯催化环氧化反应中表现出了优异的催化活性及稳定性能.     

烯丙基酯光学树脂的表征及反应动力学

通过邻苯二甲酸二烯丙酯(DAP)与1,3-丙二醇(PDO)在二丁基氧化锡(DBTO)催化下反应合成烯丙基酯光学树脂(DAP-AEO),并用红外光谱(FT-IR)、核磁共振谱图(1H-NMR)、凝胶渗透色谱(GPC)及双键含量测定对其进行了结构表征。结果表明:DAP-AEO的黄度指数为3.0,550 nm处透过率达99.5%,折光率n2D0=1.533,粘度80 mPa.s。提出转化率小于80%时的酯交换反应动力学模型,并通过测定反应过程中双键含量的变化与烯丙醇馏量来验证该模型。     

载钛催化剂的气固相法制备及其在环氧化氯丙烯反应中的催化活性

利用TiCl4气固相法,以含硅物质为原料,制备了7种钛硅氧化物类催化剂,并考察了其在H2O2环氧化氯丙烯反应中的催化活性。实验结果表明：只有以HZSM-5为载体制备的催化剂具有催化环氧化活性。酸处理HZSM-5对催化剂活性的影响并不大,分子筛的硅铝比和气固相反应时间是影响其催化活性的重要因素,且催化活性随着硅铝比的降低而降低。气固相反应时间16h时,催化剂的活性最高。     

Ti-MWW催化烯丙基氯环氧化高效合成环氧氯丙烷

 研究了具有MWW结构的新一代钛硅分子筛Ti-MWW催化剂对烯丙基氯液相环氧化高效合成环氧氯丙烷的催化性能. 结果表明, Ti-MWW的催化活性以及产物选择性均优于传统的钛硅分子筛TS-1. 对于Ti-MWW,合适的溶剂为非质子性溶剂丙酮和乙腈,在该溶剂中环氧化物不易发生溶剂化开环反应; 而对于TS-1,合适的溶剂是质子性溶剂甲醇,但甲醇可导致醇醚副产物的生成. 在Ti-MWW催化剂上烯丙基氯的转化率和环氧氯丙烷的选择性都能达到99%以上.     

磷钨杂多酸盐催化的氯丙烯水油两相条件下的环氧化

研究了磷钨杂多酸盐对氯丙烯与H2O2水溶液两相条件下环氧化反应的催化活性.反应结果表明,环氧氯丙烷的产率受溶剂二氯乙烷量影响;二氯乙烷作溶剂时,这一反应体系具有很好的催化性能,环氧氯丙烷产率可达88.3%;甲苯不是氯丙烯环氧化的优良溶剂.     

Cyclopolymerization Kinetics of Dimethyl Diallyl Ammonium Chloride

A survey is made of the present knowledge about the kinetics and mechanism of the radical cyclopolymerization of dimethyl diallyl ammonium chloride which results in soluble, strong cationic poly-electrolytes. The kinetic analysis, taking into consideration nearly complete cyclization, a linear increase of kp /kt, 0.5 with [M], and different mechanism of initiation depending on the nature of the initiator, leads to rate equations which fit the experimental data well. Initiation with S₂O₈2- has the following peculiarities: formation of primary radicals by redox reaction with chloride ions and interaction with the monomer cation, additional termination by chlorine atoms, and an experimental chain transfer constant to monomer which includes transfer to monomer and termination by chlorine radicals.     

Model for Kinetics of Vinyl Chloride Polymerization

This paper gives a critical review of recent models for the polymerization of vinyl chloride. In solution and bulk polymerization the effect of eventual degradative chain transfer to monomer, addition of chain transfer agents, and precipitation of polymer is discussed. A model for emulsion polymerization is described which includes particle formation and kinetics of polymerization where especially desorption and reabsorption of radicals in the particles are included.     

无机钛硅原料合成TS-1催化氯丙烯环氧化反应

采用无机钛硅原料体系合成出了TS-1分子筛,并对TS-1分子筛催化氯丙烯环氧化反应进行了研究.在以甲醇为溶剂的体系中考察了反应时间、反应温度、催化剂用量、氯丙烯与双氧水的摩尔比对反应的影响,得到了无机钛硅原料体系合成的TS-1催化氯丙烯环氧化反应的最优条件:反应时间为60 min,反应温度为45℃,催化剂用量为22.5 g L-1,氯丙烯与双氧水的摩尔比n(AC):n(H2O2)=1.8,并对无机钛硅原料体系合成的TS-1进行了修饰改性,评价了其催化性能.     

Ti-MWW催化氯丙烯环氧化反应动力学行为

以Ti-MWW分子筛为催化剂,以H2O2为氧化剂,系统研究了氯丙烯环氧化反应的动力学行为.结果表明,该反应速率与Ti-MWW分子筛的用量成正比,是1级反应.当H2O2浓度小于0.67 mol/L时,环氧化反应为1级反应;大于2 mol/L时,为0级反应.随着氯丙烯浓度的增加,环氧化反应级数从1级向0级转变;且只有当其浓...     

磷钨杂多酸盐／SiO2可逆负载催化剂催化氯丙烯环氧化制环氧氯丙烷

通过原位负载法合成了一种新的具有可逆负载特性的磷钨杂多酸盐/SiO2催化剂,并应用于氯丙烯环氧化反应.在反应温度65℃的条件下,系统研究了原位负载过程中反应时间、调节剂Na2HPO4用量、烯烃/H2O2摩尔比和硅烷化硅胶粒度大小等因素对环氧化反应的影响,并考察了催化剂的循环使用效果.实验结果表明,在适宜的反应条件下,初始反应环氧氯丙烷的产率达86·5%,催化剂循环使用3次,催化活性基本保持不变.     

粗硼砂的氯化铵溶液浸提动力学

研究了反应温度、溶液浓度、固液比、固体粒径大小和搅拌速度对氯化铵溶液浸提粗硼砂(十水四硼酸钠,Na₂B₄O₇·10H₂O)动力学的影响。结果表明反应速率随反应温度、溶液浓度的增加和固体粒径、固液比的减小而增加,但搅拌速度对溶解速率无显著影响。根据均相和多相动反应力学模型研究了粗硼砂的溶解过程。结果表明溶解速率遵从假一级均相反应模型。粗硼砂在氯化铵溶液中溶解的活化能为82.73 kJ·mol^-1。     

The Kinetics of Indium Electroreduction from Chloride Solutions

The electroreduction of indium on indium electrode (99.98%) in perchlorate-containing chloride electrolytes is studied by the methods of linear sweep and cyclic voltammetry, impedance spectroscopy, and chronoamperometry. The indium electroreduction is limited by diffusion, the reaction rate constant is 1.3 10^–4 cm/s at the indium salt concentration of 0.1 M. The values of the apparent rate constant for the charge transfer stage found by linear sweep and cyclic voltammetry and also by impedance spectroscopy are 2.37 × 10^–3, 3.62 × 10^–3, 3.06 × 10^–3 cm/s, respectively. The values of diffusion coefficient of indium(III) ions calculated according to the Cottrell equation based on chronoamperametric measurements and from the Warburg impedance found by impedance spectroscopy are in good agreement. The presence of the Gerischer impedance is stated, which suggests that a homogeneous reaction of formation of indium chloride complexes proceeds and its mechanism is chemical-electrochemical.

     

Kinetics of the Alkaline Dehydrochlorination of Polyvinyl Chloride)

From previous investigations of the alkaline dehydrochlorination of PVC it is well known that polyene sequences are formed. In this paper the true overall kinetics of the dehydrochlorination reaction between PVC and alcoholic KOH in tetrahydrofuran solution was studied at 9.5°C by measuring the rate of disappearance of KOH. Titrations of the hydroxide ions consumed and the chloride ions evolved showed close agreement. IR spectra of the samples did not show any evidence of substitution by hydroxide ions. Small amounts of DMSO present in the solvent were found to increase the reaction rate markedly. The kinetic scheme was discussed and the first rate constant was determined. Preliminary results of reactions of the polyene sequences with various reagents are presented. These reactions were made in order to introduce new functional groups into the PVC chains.     

Kinetics of Interfacial Polycondensation of Bisphenols with Isophthaloyl Chloride

Reaction rates of interfacial polycondensation of bisphenol A and chlorobisphenol II with isophthaloyl chloride were investigated. Rate constants and activation energies were determined The reaction rate was found to depend on stirring speed, catalyst, type of bisphenol, and temperature.