Laser induced surface damage, thermal transport and microhardness studies on certain organic and semiorganic nonlinear optical crystals

N-alkyl-2,6-dimethyl-4(1H)-pyridinones, salts of 4-dimethylaminopyridine and 2-amino-5-nitropyridine are considered to be potential candidates for nonlinear optical (NLO) applications, in particular for the generation of blue-green laser radiation. Single crystals were grown following the slow evaporation technique at constant temperature. Single-shot laser-induced surface damage thresholds in the range 3–10 GW/cm² were measured using a 18 ns Q-switched Nd:YAG laser. The surface morphologies of the damaged crystals were examined under an optical microscope and the nature of damage identified. The Vicker’s microhardness was determined at a load of 98.07 mN. The thermal transport properties, thermal diffusivity (α), thermal effusivity (e), thermal conductivity (K) and heat capacity (C_p), of the grown crystals were measured by an improved photopyroelectric technique at room temperature. All the results are presented and discussed. PACS 42.70.Mp; 61.66.Hq; 67.80.Gb; 42.65.-k     

莫尔条纹法测量微小旋转角度的频域分析

利用菲涅耳衍射的频域分析方法,对莫尔条纹复振幅分布公式进行了理论推导,得到了使用两块相同光栅组成的光栅付测量微小角度的原理公式,与利用几何光学等方法得到的结论一致.模拟结果表明：莫尔条纹是光栅付拍现象的最低频率含量,莫尔条纹内含有大量高次谐波|在探测器光学系统放大率一定的前提下,为通过直接测量莫尔条纹宽度的变化达到测量角度变化的目的,必须根据测角精度、探测器的尺寸和分辨率选择合适的光栅付光栅常数和光栅付初始夹角.     

New final doublets and power densities for the international linear collider small crossing angle layout

In this paper we use current and proposed final doublet magnet technologies to reoptimise the interaction region of the international linear collider and reduce the power losses. The result is a set of three new final doublet layouts with improved beam transport properties. The effect of localised power deposition and it’s reduction using tungsten liners are considered.      

Characterization of photorefractive materials by spontaneous noncolinear frequency doubling

‘Spontaneous’ noncolinear frequency doubling (SNCFD) is a type of optical second-harmonic generation (SHG) that uses scattered light to provide additional fundamental beams in order to accomplish noncolinear phase matching. Based on a novel algorithm for the automated evaluation of the resulting ring patterns, we present an easy-to-apply, sensitive, and non-destructive method for the characterization of photorefractive materials, yielding two-dimensional spatial resolution. As applications of the technique, examples for the characterization of lithium niobate crystals are presented. Received: 30 October 1998 / Revised version: 17 December 1998 / Published online: 7 April 1999     

Comparative study of different Schlieren diffracting elements

This paper presents an analysis of diffraction effects taking place at different Schlieren diffracting elements. Two types of diffraction effects are prominent in the Schlieren schemes. One is diffraction of direct light (source image) at the Schlieren element, which limits the sensitivity and resolution of Schlieren systems. The second type is the diffraction of light deflected from the test object at the Schlieren-diffracting element. This second type of diffraction degrades the quality of Schlieren results. Experimental results showing the effect of diffraction of light deflected from the test object at a phase knife-edge, corner of a square phase aperture and an optical fiber tip as Schlieren diffracting elements have been presented and discussed.      

Ultrasonic measurement of the elastic properties of benzoyl glycine single crystals

Certain organic crystals are found to possess high non-linear optical coefficients, often one to two orders of magnitude higher than those of the well-known inorganic non-linear optical materials. Benzoyl glycine is one such crystal whose optical second-harmonic generation efficiency is much higher than that of potassium dihydrogen phosphate. Single crystals of benzoyl glycine are grown by solvent evaporation technique usingN, N-dimethyl formamide as the solvent. All the nine second-order elastic stiffness constants of this orthorhombic crystal are determined from ultrasonic wave velocity measurements employing the pulse echo overlap technique. The anisotropy of elastic wave propagation in this crystal is demonstrated by plotting the phase velocity, slowness, Young’s modulus and linear compressibility surfaces along symmetry planes. The volume compressibility, bulk modulus and relevant Poisson’s ratios are also determined. Variation of the diagonal elastic stiffness constants with temperature over a limited range are measured and reported.     

Temperature dependence of the sensitivity of a long-range surface plasmon optical sensor

The temperature dependence of the sensitivity of an optical sensor based on long-range surface plasmon resonance (LRSPR) is studied via theoretical modeling. Both the ‘angular interrogation’ and the ‘wavelength interrogation’ modes of operation are studied. In addition, the variation of the full width at half maximum of the LRSPR ‘reflectance dip’ is also studied as a function of temperature, which ultimately determines the temperature dependence of the sensitivity of the sensor when the reflectance is monitored at a fixed incident angle (‘reflectance interrogation’). It is found that while most of the time only the ‘reflectance interrogation’ mode leads to improved sensitivity for the LRSPR sensor compared to a conventional SPR sensor, the temperature stability of the operation of the LRSPR sensor is generally higher than (or at least comparable to) that of the SPR sensor. PACS 73.20.Mf; 07.07.Df     

STUDY OF MILLIMETER-WAVE WAVEGUIDES USING A 2-D ORDER-MARCHING TIME-DOMAIN METHOD

In this paper, the application of the order-marching time-domain (OMTD) method to the solution of the cutoff frequencies of TE and TM modes in millimeter-wave waveguides is described. Starting from Maxwell’s two-dimensional (2-D) differential equations for TE or TM case, the OMTD method uses the orthonormality of weighted Laguerre polynomials and Galerkin’s testing procedure to eliminate the temporal variables and results in an order-marching scheme. To verify it’s accuracy and efficiency, the numerical results for millimeter-wave guided systems are compared with those of finite-difference time-domain (FDTD) method and analytical solutions. The OMTD method improves computational efficiency notably, especially for fine grid division problems restricted by stability constraints in the FDTD method. This work was supported by the National Natural Science Foundation of China (No. 60371008) and the CRT Program of UESTC.     

Schlieren成像和声场可视化

Schlieren技术是利用声场引起透明媒质光折射率的变化而实现声场可视化的光学成像技术。它具有对声场无干扰、快速、瞬态成像的特点。本文利用二维光学Fourier变换分析了Schlieren技术的成像原理,在采用连续激光和高速ICCD的Schlieren成像系统中,实验研究了平面波声场和线聚焦声场中换能器光学校准方法和声压的定量检测技术。发展声场瞬态和动态成像技术,观测了声波的聚焦过程和固-液界面的声场分布和变化。这些结果表明Schlieren技术是一种有效的声场可视化和定量检测的光学成像技术。     

Synthetic spectrum of the stratosphere in the submillimeter region

A line-by-line and layer-by-layer optimized method is used for the fast computation of new high resolution spectra in the submillimeter region for the stratospheric medium. The results are shown as synthetic spectra between 10 and 40 cm⁻¹ and the presence of lines of minor gaseous constituents in the stratospheric medium is indexed. The purpose of the calculations is to determine better the spectral emission (better than 1 %) with a minimum computation time (less than 1’/cm⁻¹). The high resolution spectra (5.10⁻⁴ cm⁻¹) show excellent submillimeter emission lines; this opens a wide field of investigation for stratospherical studies.     

Creation of excitons and defects in a CsI crystal during pulsed electron irradiation

Data presented on the influence of the temperature in the range 80–650 K on the spectral kinetics of the luminescence and transient absorption of unactivated CsI crystals under irradiation by pulsed electron beams (〈E〉=0.25 MeV, t _1/2=15 ns, j=20 A/cm²). The structure of the short-wavelength part of the transient absorption spectra at T=80–350 K exhibits features, suggesting that the nuclear subsystem of self-trapped excitons (STE’s) transforms repeatedly during their lifetime until their radiative annihilation at T⩾80 K, alternately occupying di-and trihalide ionic configurations. It is established that a temperature-induced increase in the yield of radiation defects, as well as F and H color centers, and quenching of the UV luminescence in CsI occur in the same temperature region (above 350 K) and are characterized by identical thermal activation energies (∼0.22 eV). It is postulated that the STE’s in a CsI crystal can have a trihalide ionic core with either an on-center or off-center configuration; the high-temperature luminescence of CsI crystals is associated with the radiative annihilation of an off-center STE with the structure (I⁻(I⁰I⁻ e ⁻))*. Fiz. Tverd. Tela (St. Petersburg) 40, 640–644 (April 1998)     

Comparison of different methods for the spatially resolved measurement of losses in optical crystals

This paper presents and compares two methods for spatially resolved 2D-measurement of optical losses in laseractive and nonlinear optical crystals. In the first method, the losses are determined from the decrease of the finesse of an optical resonator when the crystal is inserted. The second method uses the dependency of the power enhancement inside the cavity and the fraction of the laser power reflected from the incoupling cavity mirror on the intracavity losses. These methods provide a spatial resolution as high as 120 μm. The absolute accuracy is up to 0.001%. PACS 81.70.Fy; 78.20.Ci     

NaBi(WO<Subscript>4</Subscript>)<Subscript>2</Subscript>: In Cherenkov crystals for electromagnetic calorimetry

NaBi(WO₄)₂:In (called NBW) colorless Cherenkov crystals were synthesized and studied. A decrease in the concentration of color centers provides a 50-nm blueshift of the optical transmission spectrum of NBW crystals. Upon exposing these crystals to gamma rays at a dose of 3 · 10⁷ rad, the optical transmission spectra in these crystals remain almost the same. The energy resolution (calculated by the Monte Carlo method) of calorimeters based on NBW crystals of different compositions is discussed.     

Influence of anisotropy on the dispersion of surface plasmon-phonon polaritons in silicon carbide

Surface plasmon-phonon polaritons (SPPP’s) of types 3 and 4 are investigated in doped anisotropic single crystals of hexagonal silicon carbide (6H-SiC) in the orientation corresponding to K⊥C and xy⊥C. It is shown that a dispersion dependence of the type-3 SPPP’s bounded by K appears in 6H-SiC when the plasmon frequency increases to ν _p⊥⩾350 cm⁻¹. At ν _p⊥⩾400 cm⁻¹, ν _s(K) exists for type-4 SPPP’s in the frequency range Ω _∥ ⁺ <ν< _⊥ ⁺ . When the concentration of free charge carriers is increased, the dispersion curves are displaced toward higher frequencies. The conditions for the existence of type-3 and type-4 SPPP’s in 6H-SiC are determined. Fiz. Tverd. Tela (St. Petersburg) 40, 636–639 (April 1998)     

Fifty years of Szigeti’s dielectric theory — A review

During the period 1949–1961 Szigeti published four seminal papers on the dielectric behaviour of crystals. Szigeti’s theory is applicable to isotropic and anisotropic, ionic and covalent crystals with different structures. Szigeti’s theory connects dielectric, spectroscopic and elastic properties. An important outcome of Szigeti’s theory is the concept of the effective ionic charge (s). It is pointed out that s correlates with a number of physical properties and is a measure of ionicity of the interatomic bond. Since Szigeti’s work, several theoretical models have been proposed to account for the fact that s < 1. These models provide an insight into the complex polarization mechanisms in solids. This review summarizes Szigeti’s work and the work that followed; the implications and applications of Szigeti’s theory are discussed. Some new results are also included. Dedicated to the memory of late Prof. P S Narayanan.     

Flexo-electric polarization and anchoring energy for a nematic liquid crystal in a hybrid cell

Summary The flexo-electric polarization of hybrid nematic cells filled with 5 CB was measured as a function of cell thickness. To this aim the pyroelectric response of a nematic layer with small amount of light absorbing dye dissolved was detected in a nematic temperature range. From the experimental data the angle of the director deviation at the homeotropic boundary was calculated as a function of cell thickness. This dependence allows the qualitative determination of the shape of the potential well for the director deviation which is inconsistent with Rapini’s sinesquared form. The ?apparent? Rapini’s anchoring energy varies with a surface director angle (at the homeotropic boundary) from 5·10⁻³ to 3.5·10⁻² erg·cm⁻². Work presented at the second USSR-Italy Bilateral Meeting on Liquid Crystals held in Moscow, September 15–21, 1988.     

Cantilever-based photoacoustic detection of carbon dioxide using a fiber-amplified diode laser

A compact and sensitive photoacoustic setup has been developed based on a recently demonstrated cantilever technique. A micromechanical cantilever transducer is attached to a cylindrical photoacoustic cell and the cantilever’s deflection is monitored with a compact Michelson interferometer. A commercial 1-Watt optical fiber amplifier was used to enhance the performance of the system. A normalized sensitivity of 1.4×10^-10 cm^-1 W Hz^-1/2 was achieved in the detection of carbon dioxide at 1572 nm wavelength. Using 34 mW optical power from a DFB diode laser, the noise-equivalent detection limit for carbon dioxide at this wavelength is 4.0 ppm. Employing the fiber amplifier, we improved the sensitivity to yield measurement of sub-ppm concentrations. PACS 42.62.Fi; 42.55.Px; 82.80.Ch     

Nanoscopic measurements of the electrostriction responses in P(VDF/TrFE) ultra-thin-film copolymer using atomic force microscopy

Atomic force microscopy (AFM) has been used as a new method to perform nanoscale measurements of the electrostriction coefficients in the lamellae structure of the ferroelectric P(VDF/TrFE) 73/27 copolymers. The result found shows that the electrostriction coefficient inside (in the middle of) the lamella crystals is 6×10^-19 (m²V^-2), which is three times larger than that at the boundary, 2×10^-19 (m²V^-2). To explain the dependence of the electrostriction coefficients with those two regions, some suggestions are proposed. By heat treatment at 140 °C during 2 h, the sample changed its morphology as well as its crystallinity; the amorphous phase is much reduced and the degree of the crystallinity inside the lamellae is higher than that in the border. Also, it is suggested that in the lamellae’s boundary the macromolecular chains come to an end, or one monolayer folds over the other layer. In this case, the electrostriction was suppressed due to the loss of surface energy in the lamellae’s boundary. The achievements will supply a guideline to develop new and better devices for electromechanical and actuator applications. Received: 23 June 2000 / Accepted: 23 August 2000 / Published online: 5 October 2000     

Reaction48Ca (p,n)48Sc fromE p =1.885 to 5.1 MeV

The total (p, n) reaction cross section for⁴⁸Ca has been measured as a function of proton energy in the energy range 1.885 to 5.100 MeV with an overall resolution of ∼ 2 keV and in ∼ 5 keV energy steps. The fluctutions in fine resolution data have been analysed to determine the average coherence width 〈Γ〉. The excitation function averaged over large energy intervals has been analyzed in terms of the optical model. The isobaric analogue resonances atE _p ∼ 1.95 and 4 MeV have been shape-analyzed to extract the proton partial width and the spectroscopic factorS _n . A comparison of the gross structures observed in ∼ 55 keV averaged excitation function with the predictions of Izumo’s partial equilibrium model has also been made.