An iron–organic polymeric smoke suppressant for poly(vinyl chloride)

The incorporation of a poly[ferrocene-1, 2 (1, 3: 1, 1′)diylmethylene] fraction with M?_n=2100 as a smoke suppressant additive into both unplasticized and di(2-ethylhexyl)phthalate-plasticized, calcium carbonate-filled poly(vinyl chloride) (PVC) compositions entails appreciable reductions in smoke evolution during combustion tests relative to unmodified formulations. Best results, with smoke density reductions in the range 25-80%, are obtained at the 3% loading level, with higher additive concentrations causing no further improvements. The findings of this study may have implications on the design of other polymeric engineering materials exposed to potential fire hazards.     

Transition from crazing to shear deformation in ABS/PVC blends

ABS/PVC blends were prepared over a range of compositions by mixing PVC, SAN, and PB‐g‐SAN. All samples were designed to have a constant rubber level of 12 wt % and the ratio of total‐SAN to PVC in the matrix of the blends varied from 70.5/17.5 to 18/80. Transmission electron microscope and scanning electron microscope have been used to study deformation mechanisms in the ABS/PVC blends. Several different types of microscopic deformation mechanisms, depending on the composition of blends, were observed for the ABS/PVC blends. When the blend is a SAN‐rich system, the main deformation mechanisms were crazing of the matrix. When the blend is a PVC‐rich system, crazing could no longer be detected, while shear yielding of the matrix and cavitation of the rubber particles were the main mechanisms of deformation. When the composition of blend is in the intermediate state, both crazing and shear yielding of matrix were observed. This suggests that there is a transition of deformation mechanism in ABS/PVC blends with the change in composition, which is from crazing to shear deformation. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 687–695, 2006     

Studies of photooxidative degradation of poly(vinyl chloride)/poly(ethylene oxide) blends

The photooxidative degradation of blends (in a full range of compositions) of amorphous poly(vinyl chloride) (PVC) with semicrystalline poly(ethylene oxide) (PEO) in the form of thin films is investigated using absorption spectroscopy (UV–visible and Fourier transform infrared) and atomic force microscopy (AFM). The amount of insoluble gel formed as a result of photocrosslinking is estimated gravimetrically. It is found that the PVC/PEO blendsí susceptibility to photooxidative degradation differs from that pure of the components and depends on the blend composition and morphology. Photoreactions such as degradation and oxidation are accelerated whereas dehydrochlorination is retarded in blends. The photocrosslinking efficiency in PVC/PEO blends is higher than in PVC; moreover, PEO is also involved in this process. AFM images showing the lamellar structure of semicrystalline PEO in the blend lead to the conclusion that the presence of PVC does not disturb the crystallization process of PEO. The changes induced by UV irradiation allow the observation of more of the distinct PEO crystallites. This is probably caused by recrystallization of short, more mobile chains in degraded PEO or by partial removal of the less stable amorphous phase from the film surface. These results confirm previous information on the miscibility of PVC with PEO. The mechanism of the interactions between the components and the blend photodegradation are discussed. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 585–602, 2004     

Development and characterization of reactive extruded PVC/polyacrylate blends

This paper describes a method to obtain polymer blends by the absorption of a liquid solution of monomer, initiator, and a crosslinking agent in suspension type porous poly(vinyl chloride) (PVC) particles, forming a dry blend. These PVC/monomer dry blends are reactively polymerized in a twin‐screw extruder to obtain the in situ polymerization in a melt state of various blends: PVC/poly(methyl methacrylate) (PVC/PMMA), PVC/poly(vinyl acetate) (PVC/PVAc), PVC/poly(butyl acrylate) (PVC/PBA) and PVC/poly(ethylhexyl acrylate) (PVC/PEHA). Physical PVC/PMMA blends were produced, and the properties of those blends are compared to reactive blends of similar compositions. Owing to the high polymerization temperature (180°C), the polymers formed in this reactive polymerization process have low molecular weight. These short polymer chains plasticize the PVC phase reducing the melt viscosity, glass transition and the static modulus. Reactive blends of PVC/PMMA and PVC/PVAc are more compatible than the reactive PVC/PBA and PVC/PEHA blends. Reactive PVC/PMMA and PVC/PVAc blends are transparent, form single phase morphology, have single glass transition temperature (T_g), and show mechanical properties that are not inferior than that of neat PVC. Reactive PVC/PBA and PVC/PEHA blends are incompatible and two discrete phases are observed in each blend. However, those blends exhibit single glass transition owing to low content of the dispersed phase particles, which is probably too low to be detected by dynamic mechanical thermal analysis (DMTA) as a separate T_g value. The reactive PVC/PEHA show exceptional high elongation at break (～90%) owing to energy absorption optimized at this dispersed particle size (0.2–0.8 µm). Copyright © 2005 John Wiley & Sons, Ltd.     

PVC硬脂酸轻稀土热稳定剂的复配与应用研究

为了进一步研发性价比高且"无铅化"的稀土复合热稳定剂,研究了系列硬脂酸轻稀土盐(镧/铈/镨/钕/钐/铕/混合)与其他常用PVC热稳定(助)剂的复配效果。通过刚果红试纸法、红外光谱分析(FT-IR)、转矩流变仪等探究了复合热稳定剂对PVC性能的影响。结果表明:复合热稳定剂配方为硬脂酸轻稀土盐0.7~1.0份、硬脂酸锌0.8~0.9份、β-二酮0.3~0.6份和季戊四醇0.8~0.9份。将3份复合热稳定剂添加到100份PVC树脂中,静态及动态热稳定时间延长至100和35 min左右;动态热稳定性能和力学性能优于市售钙锌热稳定剂,与市售铅盐较接近。红外光谱分析表明复合热稳定剂可在加热初期减缓PVC氧化降解,较好地抑制初期着色,对PVC性能影响顺序为:镧组钕组混合组铈组镨组钐组铕组。     

Optimization of Biodegradable Nanocomposites Based on aPLA/PCL Blends for Food Packaging Applications

Biodegradable blends of amorphous poly(lactic acid) (aPLA) and polycaprolactone (PCL) and nanocomposites of these blends were developed by melt blending. A morphological study of the bioblends was carried out by means of WAXS and SEM showing immiscible behavior. The nanocomposites were also characterized morphologically by WAXS, TEM and SEM, revealing high degree of interaction of the nanoclays with the aPLA. Mechanical, thermal and gas barrier properties of the different blends and nanocomposites were studied and the effect of blending and clay addition on the above-mentioned properties was evaluated.     

Thermal diffusivity study of polystyrene/poly(vinyl methyl ether) blends by flash radiometry

This article presents thermal diffusivity (D) measurements by flash radiometry for the polymer blend of polystyrene (PS) and poly(vinyl methyl ether) (PVME) with lower critical solution temperature (LCST) phase diagram. Dependence of D on PS content measured at 100°C coincides a phase diagram determined by a cloud point measurement. D value for the blend decreases with increasing PS content and has minimum value at the PS content around 20 wt % from which D increases again with increasing PS content. If the concentration fluctuation between two components in the miscible states at the temperature close to LCST causes the remarkable phonon scattering, the composition dependence of D would resemble the phase diagram. D for the sample in the phase-separated state is larger than that for the miscible state. The larger D in the phase-separated sample would be due to the decrease of the total surface area microscopically contacted to the counter component in the phase-separated state. Dependence of D on temperature for the phase-separated sample is quite different from that of the miscible one. On an isothermal measurement of D for PS/PVME (10 : 90) at 110°C just below the cloud point, D started to increase at time above 100 min and leveled out above 250 min. Isothermal observation of sample film by a differential interference contrast microscopy showed the creation of some structure due to the nucleation and growth of interface at 225 min and it became obvious above 250 min. Thus, the increase in D at 110°C implies that D can sensitively reflect the change in microscopic structures which follows the nucleation and growth of interface. © 1997 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 35 : 1869–1876, 1997     

A verification by FTIR spectroscopy of the effect of some local chain conformations on the specific molecular interactions of solvents,esters, and polyesters with PVC

The molecular interactions of poly(vinylchloride) (PVC) with some solvents [cyclohexanone (CH), methyl ethyl ketone (MEK) and N-methylpirrolidone (MP)], esters [dioctylphthalate (DOP) and butyl stearate (BuSt)], and polyesters [poly(ethylene adipate) (PEA) and poly(ε-caprolactone) (PCL)] have been investigated by FTIR spectroscopy. In all cases the band of the carbonyl group is found to shift to lower frequencies, but significant differences between the solvent and the esters, whether polymeric or not, are evidenced. For PVC-solvent systems, the shift proves to increase linearly as PVC/solvent ratio increases, what suggests that only a definite number of polymer sites is involved. From the slopes of the straight lines this effect of composition is shown to increase in the order MP < MEK < CH, i.e., as the basicity of the solvent decreases. In contrast, for the PVC-esters or polyester blends, a nonlinear behavior consisting of two distinct interaction processes, is obtained. The increase of shift as PVC/ester ratio increases is faster in the first process for all PVC-ester systems and it is particularly enhanced for BuSt and, to a lesser extent, for DOP. Instead, during the second process, that increase is of little significance for BuSt relative to DOP and PCL. These results account for the saturation of the polymer structures that are capable of interacting, at different rates depending on the type of ester. Besides, the whole number of those structures appears to be lower than in the case of solvents. The results are discussed on the ground of, on one side, the mechanism of nucleophilic substitution on PVC, in the same solutions and blends, which, as found previously, is of a stereospecific nature, and, on the other, the electron-donor-acceptor concept (EDA) and the hard-soft-acid-base concept (HSAB) as applied to both the interacting agents (solvents and esters) and the isotactic GTGT and GTTG^? triad conformations as well as the heterotactic GTTT. In the light of the resulting conclusions it is suggested that: (i) the linear behavior shown by the solvents obeys the solvent ability to ensure a dynamic equilibrium between the two possible conformations of - mmr - sequence, i.e., GTGTTT and GTTG^?TT, through the preferential interaction with the little likely GTTG^? conformation, the content of which happens so to be constant as long as there are - mmr - sequences in solution; (ii) the nonlinear behavior of PVC-ester or polyester binary systems reveals a nonequilibrium situation and so the conformational change GTGTTT ? GTTG^?TT, which is highly hindered, will occur occasionally depending on the ester nature. This enables one to attribute the fast and the slow interaction processes to the permanent GTTG^?TT conformations derived from the polymerization and to the same conformations formed as the result of the conformational changes, respectively. Strong support for the above novel finding that PVC … O?C interaction is of a local conformational nature is given by two additional investigations. First, a similar study with a PVC sample prepared at ?50°C, shows that the carbonyl band shifts of CH and PCL are appreciably lower than those of PVC prepared at 70°C. The same holds for the blendof PCL with the latter PVC sample after substitution reaction (0.6%) at ?15°C in CH with sodium benzenethiolate (NaBT). Since the PVC obtained at ?50°C and the 0.6% substituted polymer exhibit a lower content of both permanent GTTG^?TT conformations ad -mmr- sequence, these results agree with expectatins and confirm the above suggestions. Secondly, the changes in the C? Cl stretchign frequencies of PVC with increasing amounts of solvent or ester, as extensively studied, clearly indicate the occurrence of the aforementioned conformational change, and so they are consistent with our proposals as to the actual conformational nature of PVC…O? C interactions. © 1995 John Wiley & Sons, Inc.     

A benign initiating system for cationic polymerization of isobutyl vinyl ether: Silver salt/aryl(alkyl) halide/lewis base

Aryl(alkyl) halides and silver salts were studied as environmentally benign initiating systems for cationic polymerization of isobutyl vinyl ether (IBVE). The reactivity of the benzyl cations could be effectively controlled by using dimethyl sulfide (Me₂S) as an additive, which was shown to be an effective Lewis base (LB), and diethyl ether as a reaction solvent. Detailed study of various benzyl cations and the order of addition of the reagents revealed that the reaction was controlled by the electronic and steric features of aryl(alkyl) halides, LBs, and IBVE, and a plausible reaction mechanism was presented. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 2050–2058     

Independence of the brittle–ductile transition from the rubber particle size for impact‐modified poly(vinyl chloride)

A series of acrylic impact modifiers (AIMs) with different particle sizes ranging from 55.2 to 927.0 nm were synthesized by seeded emulsion polymerization, and the effect of the particle size on the brittle–ductile transition of impact‐modified poly(vinyl chloride) (PVC) was investigated. For each AIM, a series of PVC/AIM blends with compositions of 6, 8, 10, 12, and 15 phr AIM in 100 phr PVC were prepared, and the Izod impact strengths of these blends were tested at 23 °C. For AIMs with particle sizes of 55.2, 59.8, 125.2, 243.2, and 341.1 nm, the blends fractured in the brittle mode when the concentration of AIM was lower than 10 phr, whereas the blends showed ductile fracture when the AIM concentration reached 10 phr. It was concluded that the brittle–ductile transition of the PVC/AIM blends was independent of the particle size in the range of 55.2–341.1 nm. When the particle size was greater than 341.1 nm, however, the brittle–ductile transition shifted to a higher AIM concentration with an increase in the particle size. Furthermore, the critical interparticle distance was found not to be the criterion of the brittle–ductile transition for the PVC/AIM blends. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 696–702, 2006     

A novel pH‐ and thermo‐sensitive PVP/CMC semi‐IPN hydrogel: Swelling,phase behavior,and drug release study

Poly(N‐vinyl‐pyrrolidone) (PVP) hydrogel has been considered as a very interesting and promising thermosensitive material. The most vital shortcoming of PVP hydrogel as thermosensitive material is that it does not exhibit thermosensitivity under usual conditions. In this work, semi‐interpenetrating polymer network (semi‐IPN) hydrogels based on PVP and carboxymethylcellulose (CMC) were prepared. The volume phase transition temperature (VPTT) of the hydrogels was determined by swelling behavior and differential scanning calorimetry (DSC). The results showed that the VPTT was significantly dependent on CMC content and the pH of the swelling medium. The amount of CMC in the semi‐IPN hydrogels was 0.050, 0.075, and 0.100 g, the VPTT in buffer solution of pH 1.2 was 29.9 °C, 27.5 °C and 24.5 °C, respectively. In addition, the VPTT occurred in buffer solution of pH 1.2, but did not appear in alkaline medium. Bovine serum albumin (BSA) as a model drug was loaded and the in vitro release studies were carried out in different buffer solutions and at different temperatures. The results of this study suggest that PVP/CMC semi‐IPN hydrogels could serve as potential candidates for protein drug delivery in the intestine. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 1749–1756, 2010