Synthesis and properties of polyetheretherketone–polydimethylsiloxane block copolymers

Polyetheretherketone-polydimethylsiloxane (PEEK–PDMS) block copolymers were synthesized from the condensation of dimethylamino terminated PDMS and hydroxy terminated PEEK oligomers in 1-chloronapthalene. Yields for block copolymers synthesised from low molecular weight PDMS oligomers were good but yields were significantly reduced when higher molecular weight PDMS oligomers were used. This was related to the limited solubility of higher molecular weight PDMS in the reaction solvent. Differential scanning calorimetry (DSC) studies indicated that phase separation of the block copolymers occurred at very short segment length (M?_n < 4000). A depression in the crystallinity of both the PEEK and PDMS phases in the block copolymer was observed. Thermogravimetric analysis (TGA) studies indicated that the PEEK–PDMS block copolymers displayed insufficient thermo-oxidative stability to be melt-processed successfully in PEEK based blends.     

聚芳醚腈-聚硅氧烷嵌段共聚物的合成

采用4-烯丙基-2-甲氧基苯酚(Eugenol)为端基的聚二甲基硅氧烷与氟代苯端基含杂萘联苯结构聚芳醚腈,以碳酸钾为催化剂,二甲基亚砜与邻二氯苯为溶剂的条件下进行芳香亲核取代反应(SNAr),合成了一种高分子量的聚芳醚腈-聚硅氧烷嵌段共聚物,并采用FTIR和1H-NMR对该产物的结构进行了表征.DSC测试结果表明该类嵌段共聚物具有两个玻璃化转变温度(Tg),分别为-98～-90℃和255～287℃,而且共聚物具有优良的耐热性,10%的热失重温度(Td)在450℃以上.采用原子力显微镜和透射电镜观测发现该共聚物存在明显的相分离特征.     

刚性链嵌段共聚物的研究(I)——聚醚醚酮-聚醚砜嵌段共聚物结构与性能

本文以聚醚醚酮(PEEK)和聚醚砜(PES)齐聚物为原料,通过溶液缩聚法制备PEEK-PES嵌段共聚物,并用DSC、TGA、WAXD和动态粘弹谱等手段对其相容性、结晶行为、动态力学性能和热性能进行了研究.结果表明,嵌段共聚物在PEEK链段M_n=1×10⁴,PES链段M_n)=3500～250(PES含量为25.0%～2.9%)组成范围内不产生微相分离,保持了结晶性能,其玻璃化转变温度比纯PEEK提高将近20℃,并具有较好的高温力学性能.     

Novel triblock siloxane copolymers: Synthesis,characterization, and their use as surface modifying additives

Synthesis of novel triblock, polycaprolactone-b-polydimethylsiloxane (PDMS) and poly(2-ethyl-oxazoline)-b-PDMS copolymers were demonstrated. These materials were obtained via the ring-opening polymerization of ?-caprolactone or 2-ethyl-2-oxazoline monomers by using organofunctionally terminated PDMS oligomers as initiators and comonomers. Segment molecular weights in these copolymers were varied over a wide range between 1000 and 2000 g/mol and the formation of copolymers with desired backbone compositions were monitored by ¹H-NMR spectroscopy and GPC. DSC and TMA studies showed the formation of two phase morphologies with PDMS (T_g, ?120°C) and polycaprolactone (T_m, 50–60°C) or poly(2-ethyl-2-oxazoline) (T_g, 40-60°C) transitions respectively. The use of polycaprolactone-b-PDMS copolymers as surface modifying additives in polymer blends were also investigated. When these copolymers were blended at low levels (0.25–10.0% by weight) with various commercial resins such as, polyurethanes, PVC, PMMA, and PET, the resulting systems displayed silicone-like, hydrophobic surface properties, as determined by critical surface tension measurements or water contact angles. The effect of siloxane content, block length, base polymer type and morphology on the resulting surfaces are discussed.     

Library synthesis and characterization of 3‐aminopropyl‐terminated poly(dimethylsiloxane)s and poly(ϵ‐caprolactone)‐b‐poly(dimethylsiloxane)s

Libraries of 3‐aminopropyl‐terminated poly(dimethylsiloxane) (APT–PDMS) and poly(?‐caprolactone)–poly(dimethylsiloxane)–poly(?‐caprolactone) (PCL—PDMS–PCL) triblock copolymers were synthesized. Preliminary experiments were carried out to select an appropriate catalyst and route for the poly(dimethylsiloxane) synthesis, and trial experiments were conducted to verify the successful synthesis of the intended polymer compositions. Then, a series of APT–PDMS oligomers were synthesized with an automated combinatorial high‐throughput synthesis system to cover a molecular weight range of 2500–50,000 g/mol. Trial PCL—PDMS–PCL triblock copolymers were synthesized with the automated reactor system and characterized in detail with rapid gel permeation chromatography, high‐throughput Fourier transform infrared, nuclear magnetic resonance, and differential scanning calorimetry. Finally, two library synthesis experiments were carried out in which the lengths of both the poly(dimethylsiloxane) and poly(?‐caprolactone) blocks in the PCL—PDMS–PCL triblock copolymers were varied. The results obtained from these experiments demonstrated that it was possible to synthesize libraries of well‐defined APT–PDMS oligomers and PCL—PDMS–PCL triblock copolymers with an automated high‐throughput system. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 4880–4894, 2006     

Synthesis and properties of polydimethylsiloxane-containing block copolymers via living radical polymerization

Polydimethylsiloxane (PDMS) block copolymers were synthesized by using PDMS macroinitiators with copper-mediated living radical polymerization. Diamino PDMS led to initiators that gave ABA block copolymers, but there was low initiator efficiency and molecular weights are somewhat uncontrolled. The use of mono- and difunctional carbinol–hydroxyl functional initiators led to AB and ABA block copolymers with narrow polydispersity indices (PDIs) and controlled number-average molecular weights (M_n's). Polymerization with methyl methacrylate (MMA) and 2-dimethylaminoethyl methacrylate (DMAEMA) was discovered with a range of molecular weights produced. Polymerizations proceeded with excellent first-order kinetics indicative of living polymerization. ABA block copolymers with MMA were prepared with between 28 and 84 wt % poly(methyl methacrylate) with M_n's between 7.6 and 35 K (PDI <1.30), which show thermal transitions characteristic of block copolymers. ABA block copolymers with DMAEMA led to amphiphilic block copolymers with M_n's between 9.5 and 45.7 K (PDIs of 1.25–1.70), which formed aggregates in solution with a critical micelle concentration of 0.1 g dm⁻³ as determined by pyrene fluorimetry experiments. Monocarbinol functional PDMS gave AB block copolymers with both MMA and DMAEMA. © 2001 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 1833–1842, 2001     

聚苯乙烯-b-聚硅氧烷-b-聚苯乙烯三嵌段共聚物的合成及表征

采用乙烯基封端的聚 (二甲基硅氧烷 )与溴化氢反应制得末端含有C Br的双官能聚 (二甲基硅氧烷 ) ,以此聚 (二甲基硅氧烷 )大分子为引发剂 ,CuCl为催化剂 ,4 ,4′ 二 (5 壬基 ) 2 ,2′ 联吡啶为配体 ,通过原子转移自由基聚合法 ,制得分子量和结构可控的聚苯乙烯 b 聚硅氧烷 b 聚苯乙烯 (PSt b PDMS b PSt)共聚物 .     

聚苯乙烯/聚二甲基硅氧烷嵌段与接枝共聚物表面聚集态的研究

利用ATR单点全反射技术以及XPS(X光电子能谱 )测试方法对聚苯乙烯 聚二甲基硅氧烷嵌段 (PS b PDMS)和接枝共聚物 (PS g PDMS)进行了研究 ,发现聚合物膜表面存在着有机硅富集层 ,PS b PDMS有机硅表面富集程度要高于PS g PDMS ,而且不同溶解度参数的成膜溶剂和不同极性的成膜介质对有机硅富集程度有一定的影响 .     

Synthesis and characterization of polysiloxane–polyamide block and graft copolymers

The synthesis of copolymers constituted of a central polydimethylsiloxane (PDMS) block flanked by two polyamide (PA) sequences is described. α, ω-diacyllactam PDMS, when used as macroinitiator of lactam polymerization, gives rise to the expected triblock copolymer. Likewise, PDMS-g-PA graft copolymers are obtained from acyllactam containing polysiloxanes. NaAlH₂(OCH₂CH₂OMe)₂ turns out to be the best suited activating agent for the polymerization of ?-caprolactam, in the experimental conditions required for the synthesis of polysiloxane–polyamide copolymers. The nucleophilic species formed by reaction of NaAlH₂(OCH₂CH₂OMe)₂ with ?-caprolactam—2-[bis(methoxyethoxy) aluminumoxy]-1-azacycloheptane sodium—is indeed nucleophilic enough to bring about the growth of PA chains and mild enough to stay inert towards PDMS. © 1993 John Wiley & Sons, Inc.     

Polyimide–polyformal block copolymers

In an effort to combine and tailor the properties of thermoplastic resins we have investigated the synthesis of polyimide–polyformal block copolymers prepared by the condensation reaction of α,ω-diamino functionalized polyformal oligomers with α,ω-dianhydride terminated polyimide oligomers. Amino functionalized polyformal oligomers were synthesized by displacement condensation reactions of various bisphenols with methylene dihalides in the presence of base and aminophenols. Oligomeric aromatic polyformals having weight average molecular weights (MW_w) of 7500 to 40,000 were obtained. Anhydride terminated polyimide oligomers with molecular weights (MW_w) ranging from 10,000 to 15,000 were obtained by the condensation of bisphenol-A–dianhydride and aromatic amines. Combining the polyimide oligomers with the polyformal oligomers in dipolar aprotic or nonpolar solvents afforded the desired block copolymers. The polyimide–polyformal block copolymers generally display two distinct glass transition temperatures by differential scanning calorimetry. The (AB)_n block copolymers were evaluated by TGA in both air and N₂ for thermal/oxidative stability.     

一步法制备聚二甲基硅氧烷大分子偶氮引发剂及其用于嵌段共聚物的合成

提出了一种简单易行的合成聚二甲基硅氧烷大分子偶氮引发剂的方法.通过羟基封端的聚二甲基硅氧烷(HO-PDMS-OH)与4,4′-偶氮-二(4-氰基戊酸)(ACPA)在十分温和的条件下直接进行一步缩聚反应,合成了含有PDMS链段的大分子偶氮引发剂.用这种大分子引发剂来引发聚(乙二醇)甲醚甲基丙烯酸酯大分子单体(PEGMA)进行自由基溶液聚合,得到了一系列两亲性梳状嵌段共聚物(PDMS-PEG).     

Coatings with thermally switchable surface energy produced from poly(ethylene oxide)-poly(dimethylsiloxane) block copolymer films

This work explores coatings with thermally switchable wetting behavior, based on block copolymers that possess both hydrophilic and hydrophobic segments. The amphiphilic block copolymers were synthesized by coupling allyl-ended poly(ethylene oxide) (PEO) and hydride-ended poly(dimethylsiloxane) (PDMS) oligomers via a Pt catalyst. One near-symmetric diblock possessed an order-disorder transition temperature (T_ODT) of 64 °C. When cooled through T_ODT in ambient air, the PDMS domains wet the film's surface, producing a hydrophobic coating with a water contact angle (CA) = 90°. However, when cooled in humidified air, hydrophilic PEO domains form at the surface, yielding CA = 30–40°. The coatings can be reversibly switched between the two states by reheating above T_ODT, in the appropriate environment, and then cooling, rapidly generating the desired room-temperature surface wettability. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016, 54, 135–140     

Synthesis,liquid crystalline mesophases and morphologies of diblock copolymers composed of a poly(dimethylsiloxane) block and a nematic liquid crystalline block

In this study, a series of liquid crystalline diblock copolymers, composed of a soft poly(dimethylsiloxane) (PDMS) block with a de?ned length and a side-on liquid crystalline poly(3??-acryloyloxypropyl 2,5-di(4?-butyloxybenzoyloxy) benzoate) (P3ADBB) block with different lengths, are synthesised by the atom transfer radical polymerisation. The macromolecular structures, liquid crystalline properties and the microphase-separated morphologies of the diblock copolymer are investigated by ¹H NMR, FT-IR, GPC, POM, DSC and TEM. The results show that the well-de?ned diblock copolymers (PDMS_n-b-P3ADBB_m) possess four different soft/rigid ratios (n = 58, m = 10, 25, 42, 66) and relatively narrow molecular distributions (PDI ≤ 1.30). P3ADBB blocks of the copolymers show nematic sub-phases, which are identical to the mesomorphic behaviour of the homopolymer P3ADBB. After being annealed at 90°C in a vacuum oven for 48 h, the copolymers form a lamellar morphology when m = 10 and morphologies of PDMS spheres embedded in P3ADBB matrix when m = 25, 42 and 66.     

Polysiloxane‐Backbone Block Copolymers in a One‐Pot Synthesis: A Silicone Platform for Facile Functionalization

Block copolymers consisting exclusively of a silicon–oxygen backbone are synthesized by sequential anionic ring‐opening polymerization of different cyclic siloxane monomers. After formation of a poly(dimethylsiloxane) (PDMS) block by butyllithium‐initiated polymerization of D3, a functional second block is generated by subsequent addition of tetramethyl tetravinyl cyclotetrasiloxane (D4^V), resulting in diblock copolymers comprised a simple PDMS block and a functional poly(methylvinylsiloxane) (PMVS) block. Polymers of varying block length ratios were obtained and characterized. The vinyl groups of the second block can be easily modified with a variety of side chains using hydrosilylation chemistry to attach compounds with Si—H bond. Conversion of the hydrosilylation used for polymer modification was investigated.     

两嵌段共聚物PB-PDMS中PDMS的结晶行为与共聚物形态结构的关系

聚二甲基硅氧烷(PDMS)的结晶熔融温度(T_m)约为-43℃,远高于其玻璃化转变温度(T_g)(-124℃),为扩大其低温使用范围,需要破坏其链结构规整性以抑制结晶发生。但是我们发现在前人工作中,含PDMS段的嵌段共聚物,即使不破坏PDMS段的链结构规整性,其动态力学谱上有时也观测不到PDMS的结晶峰。遗憾的是这些作者末曾对这一不寻常现象给予足够的重视。无疑,搞清共聚物中PDMS不寻常结晶行为同共聚物形态结构的关系,对提高含有PDMS段的嵌段型热塑性弹性体的低温使用范围将有指导意义。本文报导PB-PDMS中的结晶行为与共聚物形态结构的关系。     

[-PPO-PDMS-PHS-]n三元多嵌段共聚物的形态结构和性能

利用DMA, TEM和SAXS对以聚苯醚(PPO)为硬段、聚对羟基苯乙烯(PHS)为半硬段和聚二甲基硅氧烷(PDMS)为软段的三元多嵌段共聚物[-PPO-PDMS-PHS-]n以三种嵌段相容相为连续相, PPO与PHS的相容相和PDMS相为两种分散相, 其tan δ随温度变化曲线在-100℃至200℃一直是一很高的平台, 并具有优异的力学性能, 较好地解决了含有机硅类嵌段共聚物强度低的弱点, 同时又保留了嵌段共聚物微相分离的特性。     

Synthesis and applications of novel fluorinated dendrimer-type copolymers by the use of fluoroalkanoyl peroxide as a key intermediate

Fluoroalkanoyl peroxide reacted with 1,3,5,7-tetravinyl-1,3,5,7-tetramethylcyclotetrasiloxane (TTRV-Si) to afford fluoroalkyl end-capped oligomers containing some unreacted vinyl segments under very mild conditions. Fluoroalkyl end-capped cyclosiloxane oligomers containing some vinyl segments thus obtained reacted with N,N-dimethylacrylamide and fluoroalkanoyl peroxide to afford new fluorinated dendrimer-type block copolymers in good isolated yield. Similar reactions were also occurred by the use of 1,3,5-trivinyl-1,3,5-trimethylcyclotrisiloxane instead of TTRV-Si, and the corresponding fluorinated dendrimer-type block copolymer was obtained in good isolated yield. These fluorinated dendrimer-type block copolymers had an excellent solubility not only in water but also in traditional organic solvents including aliphatic fluorinated solvents. Interestingly, these fluorinated block copolymers were found to form the self-assembled dendrimer-type polymeric aggregates in aqueous solutions. More interestingly, these fluorinated block copolymers had an extremely higher dispersion ability of not only single-walled carbon nanotube and fullerenes but also magnetic nanoparticles into water, compared to that of the corresponding two fluoroalkyl end-capped oligomers.     

Synthesis and characterization of model diblock copolymers of poly(dimethylsiloxane) with poly(1,4‐butadiene) or poly(ethylene)

Model diblock copolymers of poly(1,4‐butadiene) (PB) and poly(dimethylsiloxane) (PDMS), PB‐b‐PDMS, were synthesized by the sequential anionic polymerization (high vacuum techniques) of butadiene and hexamethylciclotrisiloxane (D₃) in the presence of sec‐BuLi. By homogeneous hydrogenation of PB‐b‐PDMS, the corresponding poly(ethylene) and poly(dimethylsiloxane) block copolymers, PE‐b‐PDMS, were obtained. The synthesized block copolymers were characterized by nuclear magnetic resonance (¹H and ¹³C NMR), size‐exclusion chromatography (SEC), Fourier transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), transmission electron microscopy (TEM), and rheology. SEC combined with ¹H NMR analysis indicates that the polydispersity index of the samples (M_w/M_n) is low, and that the chemical composition of the copolymers varies from low to medium PDMS content. According to DSC and TGA experiments, the thermal stability of these block copolymers depends on the PDMS content, whereas TEM analysis reveals ordered arrangements of the microphases. The morphologies observed vary from spherical and cylindrical to lamellar domains. This ordered state (even at high temperatures) was further confirmed by small‐amplitude oscillatory shear flow tests. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1579–1590, 2006     

Synthesis and properties of new block copolymers based on polydimethylsiloxane and tetraphenylethylene-containing polyimide

New polydimethylsiloxane (PDMS)-polyimide block copolymers were synthesized by the solution polycondensation of aminopropyl-terminated polydimethylsiloxane, 1,1-bis(4-aminophenyl)-2,2-diphenylethylene, and 3,3′,4,4′-benzophenonetetracarboxylic dithioanhydride in pyridine. New 1,3-bis(3-aminopropyl)tetramethyldisiloxane (BADS)-based random copolyimides were also prepared. The inherent viscosities of all the random and block copolyimides were in the range of 0.13–0.90 dL/g in N-methyl-2-pyrrolidone. These copolymers were soluble in N,N-dimethylacetamide, N-methyl-2-pyrrolidone, and m-cresol. All the BADS-based random copolymers and PDMS-containing copolymers with PDMS content above 42 wt % were soluble in tetrahydrofuran and chloroform. Transparent or somewhat cpaque films were prepared by casting from the reaction solutions. The BADS-based random copolyimides had one glass transition temperature (T_g) in the whole composition ranges, which showed single phase nature of the copolymers. On the other hand, the PDMS-polyimide block copolymers had double T_gS, indicating phase-separated morphology. The block copolymers containing PDMS content above 73 wt % behaved like a high temperature elastomer. © 1993 John Wiley & Sons, Inc.     

Synthesis and properties of multiblock copolymers based on polydimethylsiloxane and polyamides from dicarboxylic acid and diisocyanate terminated functionalities

Polydimethylsiloxane (PDMS)–polyamide multiblock copolymers were successfully synthesized via diisocyanate route by two different procedures, i.e., the one-step and two-step methods, In the two-step method, α, ω-diisocyanate-terminated polyamide oligomers, which were prepared in situ from a mixture of isophthalic acid (IPA) and azelaic acid (AZA) with 4,4′-methylenedi (phenyl isocyanate) (MDI) in 1,3-dimethyl-2-imidazolidone (DMI) in the presence of 3-methyl-1-phenyl-2-phosopholene 1-oxide catalyst, were reacted with α, ω-bis (10-carboxydecyl) polydimethylsiloxane (PDMS-diacid) leading to the formation of multiblock copolymers. In the one-step method, the reaction components, MDI, IPA, AZA, and PDMS-diacid were reacted all together in DMI in the presence of the catalyst. These polymerizations gave multiblock copolymers having inherent viscosities in the range of 0.36–1.12 dL/g in N,N-dimethylacetamide (DMAc). These multiblock copolymers were soluble in amide-type solvents, and transparent (or translucent) and ductile films could be cast from the solutions in a mixture of DMAc and bis(2-ethoxyethyl) ether. The multiblock copolymers prepared by the two-step method had better-defined, microphase-separated morphology than those obtained by the one-step method. The mechanical properties of PDMS–polyamide multiblock copolymer films were found to be highly dependent on the PDMS content; the tensile strength and modulus of the films decreased with increasing the PDMS content.