Polysiloxane zwitterionomers and related model compounds. I. Synthesis

Polymers containing zwitterions were prepared by reacting γ-propanesultone with polydimethylsiloxane-co-(4,7-diazaheptylmethylsiloxane), which generated substituted di(ammonium-3-propane-sulfonate) groups pendant from the siloxane chain. Their concentration in the polymers varied from 0.5 to 10 mole %. Two model compounds were also prepared in order to (1) characterize the reaction leading to the formation of these zwitterions and (2) characterize the ionic forces in solutions (tetrahydrofuran and benzene were used as solvents). The degree of aggregation of these model compounds was higher in tetrahydrofuran and increased in both solutions with the concentration. No rearrangements of siloxane bonds were observed in the presence of these zwitterions or γ-propanesultone.     

Synthesis and characterization of UV-curable polydimethylsiloxane epoxy acrylate

UV-curable polydimethylsiloxane epoxy acrylate (PSEA) was synthesized by hydrosilylation of allyl glycidyl ether with hydrogen-containing polydimethylsiloxane to give polydimethylsiloxane-type epoxy resin which modified with acrylic acid. The curing speed and the double bond conversion in the UV cured film were influenced by the purity of PSEA with Fourier transform infrared spectroscopy (FT-IR) measurements. The influences of the synthetic process, such as, the reaction temperature, the concentration of reactants and the catalyst which determined the purity and activity of resins were discussed in detail. The structures of this resin were characterized by ¹H-NMR and FT-IR spectra. The molecular weight was checked by gel permeation chromatography, and M_n is 45,000. The properties of the cured film were also investigated by thermogravimetric analyzer, dynamical thermal mechanical analysis, and etc. For example, tensile strength (6.9 Mpa), elongation (20%), hardness (A; 18), water absorption (24 h; 2%), weight loss (40 min, 300 °C; 5%) and etc.     

Polydimethylsiloxane–polyurethane elastomers: Synthesis and properties of segmented copolymers and related zwitterionomers

A series of polyurethane block polymers based on hydroxybutyl-terminated polydimethyl-siloxane soft segments of molecular weight 2000 were synthesized. The hard segments consisted of 4,4′-methylenediphenylene diisocyanate (MDI) which was chain extended with either 1,4-butanediol (BD) or N-methyldiethanolamine (MDEA). The MDEA-extended materials were ionized by using 1,3-propane sultone. The weight fraction of hard segments was in the range 0.13–0.39. The morphology and properties of these polyurethane elastomers were studied by a variety of techniques. All of these short-segment block copolymers showed nearly complete phase separation. The zwitterionomer materials exhibited ionic aggregation within the hard domains. Hard-segment crystallinity or ionic aggregation did not affect the morphology. Hard-domain cohesion was found to be a more important factor than hard-domain volume fraction in determining the tensile and viscoelastic properties of these elastomers.     

Synthesis and characterization of a novel hydroxypolyether blocked polydimethylsiloxane PEO-b-PDMS-b-PEO

A novel hydroxypolyether blocked polydimethylsiloxane, poly（ethylene oxide） propyl-b-polydimethylsiloxane-b-propyl poly（ethylene oxide） （PEO-b-PDMS-b-PEO） was synthesized by simple hydrosilation reaction of poly（ethylene glycol） monoallyl ether with α,ω-dihydrogen terminated PDMS （HPDMS）. Fourier transform infrared spectroscopy （FTIR） and IH NMR were used to identify the structure of PEO-b-PDMS-b-PEO and intermediate product HPDMS. Based on the effect investigations of temperature, reactant molar ratio, catalyst and time on the hydrosilation, it was found that the conversion of Si-H bond to SiC bond increased with the increase of catalyst and time, and the reaction completed when the content of catalyst was 22μg/g and the time was 5 h, respectively. Urethane reaction of OH and NCO group confirms that PEO-b-PDMS-b-PEO is more reactive toward to diisocyanate than α,ω-dihydroxylbutyl terminated PDMS.     

Synthesis and characterization of semicrystalline triblockcopolymers of isotactic polystyrene and polydimethylsiloxane

iPS‐b‐PDMS‐b‐iPS triblock copolymers were prepared by hydrosilylation of vinyl‐terminated isotactic polystyrenes (iPS) with α,ω‐bis(dimethylsilane)‐terminated poly(dimethylsiloxane)s (PDMS). As a function of the molecular weights of the two components, the triblock copolymer composition was varied between 9.0 and 98 wt % iPS. The resulting triblock copolymers remained soluble during block copolymer synthesis due to slow iPS crystallization in solution. At iPS content exceeding 31 wt %, the iPS crystallization was achieved by postpolymerization annealing and melt processing. The triblock copolymers melted above 200 °C with melting temperatures very similar to those of the corresponding iPS homopolymers. Nanostructure and microstructure formation of both amorphous and semicrystalline triblock copolymers were examined by means of light microscopy, atomic force microscopy, and TEM measurements. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Poly(chloropropylmethyl-dimethylsiloxane)–polyurethane elastomers: Synthesis and properties of segmented copolymers and related zwitterionomers

A series of polyurethane block copolymers based on hydroxybutyl terminated poly(chloropropylmethyl-dimethylsiloxane) and poly(tetramethylene oxide) soft segments of molecular weights 2100 and 2000, respectively, were synthesized. The hard segments consisted of 4,4′-methylenediphenylene diisocyanate (MDI) that was chain extended with either 1,4-butanediol (BD) or N-methyldiethanolamine (MDEA). The materials chain extended with MDEA were ionized using 1,3-propane sultone. The weight fraction of the hard segments was in the range 0.30–0.45. The effect of mixed soft segments, chain extenders, and zwitterionization on the extent of phase separation and physical properties was studied by utilizing differential scanning calorimetry and dynamic mechanical, stress-strain, and Fourier Transform Infrared spectroscopy experiments. All of these short segment block copolymers showed nearly complete phase separation. The zwitterionomer materials exhibited ionic aggregation within the hard domains. Although hard segment crystallinity or ionic aggregation did not affect the morphology, hard domain cohesion was important in determining the tensile and viscoelastic properties of these elastomers.     

Synthesis and properties of monodisperse polydimethylsiloxane networks

α,ω-Divinyl-terminated polydimethylsiloxane polymers with low polydispersivity were synthesized via anionic polymerization of hexamethylcyclotrisiloxane (D₃). Five “monodisperse” polymers with different molecular weights were hydrosilylated with tetrakisdimethylsiloxysilane in the presence of platinum catalysts and inhibitors to form crosslinked networks. Control studies to determine the effect of platinum, silicon hydride, and heat were performed to verify that no redistribution occurred during hydrosilylation. The properties of these cured samples were characterized chemically by degradation with trifluoromethanesulfonic acid in the presence of hexamethyldisiloxane, infrared spectroscopy, and nuclear magnetic spectroscopy. Mechanical properties were studied by measurements of Shore A hardness, dynamic shear modulus, and tensile modulus. The relationship between the molecular weight of the vinyl polymer and the final properties of the cured networks was measured. © 1993 John Wiley & Sons, Inc.     

Incorporation of polydimethylsiloxane into polyurethanes and characterization of copolymers

Novel copolymers of polyurethane (PU) were prepared by direct transurethanetion reaction of a commercial PU with polydimethylsiloxanes (PDMS, MW 1000, 5000, and 10,000) containing hydroxyl end-groups. Transurethanetions with different mass ratios of hydrophobic PDMS to hydrophilic PU chains (PDMS1000–PU: 43:57, 67:33, 71:29, and 80:20; PDMS5000–PU: 37:63, and 51:49; PDMS10000–PU: 51:49) were carried out in solution at 65 and 100 °C. In catalyzed reactions, dibutyltin dilaurate (SnC₃₂H₆₄O₄) was used to promote bond breaking in the PU chain and accelerate the reaction between hydroxyl end-groups of PDMS and regenerated isocyanates of PU. The chemical structures of the prepared copolymers were comprehensively characterized by ¹H, ¹³C, and ²⁹Si NMR spectroscopies. According to elemental analysis, the content of PDMS varied between 3 wt.% and 16 wt.%, and results obtained from the ¹H NMR spectroscopy were in good agreement with the results of elemental analysis. Increased length of the hydrophobic chain increased the content of PDMS in the copolymer. The GPC results showed that molar masses of the PUPDMS copolymers were lower than the molar mass of the starting PU. The glass transitions (T_g) of the copolymers were shifted to lower temperature as compared with T_g of the starting polyurethane. ATR FTIR spectroscopy showed the surface of the copolymer films to be enriched with siloxane groups and, according to electron microscopy, it was textured with microspheres. The static contact angles for copolymer films measured with deionized water ranged from 94° to 117°. The different structural, thermal and surface properties of the PUPDMS copolymers as compared with PU indicated that transurethanetion had taken place.     

Synthesis and properties of polystyrene/polydimethylsiloxane graft copolymers

Polystyrene-graft-polydimethylsiloxane (PS-g-PDMS) copolymers with different PDMS content were synthesized by the radical bulk copolymerization of PDMS macromonomer and styrene. The copolymers were characterized by Fourier transform infrared (FT-IR), ¹H-nuclear magnetic resonance (NMR), thermogravimetric analysis (TGA), dynamic mechanical analysis (DMA), transmission electron microscopy (TEM) and the mechanical properties of the copolymers were also carried out. It was indicated that the notched impact strength and elongation at break of the polymers increased with the increase of PDMS content. The thermal stability of PS-g-PDMS is better than that of PS. __________ Translated from Journal of East China University of Science and Technology 2005, 31(2) (in Chinese)     

Synthesis and characterization of semi- and full-interpenetrating polymer networks of poly(2,6-dimethyl-1,4-phenylene oxide) and polydimethylsiloxane

The synthesis and characterization of pseudo or semi- and full-interpenetrating polymer networks (IPNs) of poly(2,6-dimethyl-1,4-phenylene oxide) and polydimethylsiloxane were performed. We observed that in full IPNs, the elasticity of the IPN samples increased very drastically, as the composition of polydimethylsiloxane increased (i.e. 0–60%) while the tensile strength (TS) and the glass transition temperature (T_g) decreases. The pseudo IPNs appeared to consist of two phases while the full IPNs of lower siloxane content were miscible.     

Synthesis and properties of polyetheretherketone–polydimethylsiloxane block copolymers

Polyetheretherketone-polydimethylsiloxane (PEEK–PDMS) block copolymers were synthesized from the condensation of dimethylamino terminated PDMS and hydroxy terminated PEEK oligomers in 1-chloronapthalene. Yields for block copolymers synthesised from low molecular weight PDMS oligomers were good but yields were significantly reduced when higher molecular weight PDMS oligomers were used. This was related to the limited solubility of higher molecular weight PDMS in the reaction solvent. Differential scanning calorimetry (DSC) studies indicated that phase separation of the block copolymers occurred at very short segment length (M?_n < 4000). A depression in the crystallinity of both the PEEK and PDMS phases in the block copolymer was observed. Thermogravimetric analysis (TGA) studies indicated that the PEEK–PDMS block copolymers displayed insufficient thermo-oxidative stability to be melt-processed successfully in PEEK based blends.     

Mesoporous titanium phosphates and related molecular sieves: Synthesis, characterization and applications

Titanium (IV) phosphates TCM-7 and -8 with mesoporous cationic framework topologies using both cationic and anionic surfactants have been synthesized. Experimental data suggest the stabilization of the tetrahedral state of Ti in TCM-7/8 (O-P-O-Ti-O-, at Ti/P = 1:1)vis-à-vis the most stable octahedral state of Ti in the rutile/anatase or pure mesoporous TiO₂. Mesoporous TCM-7 and-8 show anion exchange capacity due to the framework phosphonium cation and cation exchange capacity due to defective P-OH groups. Grafting the organic functionality in the surface or bridging the organic moiety in between the inorganic phosphorus precursors can enhance hydrophobicity of these materials similar to that of mesoporous silica materials. The high catalytic activity in the liquid phase partial oxidation of cyclohexene over such organically surface modified mesoporous titanium phosphate using a dilute H₂O₂ oxidant supports the tetrahedral coordination of Ti in these materials. These materials also show excellent photocatalytic activity in the production of H₂ by photo-reduction of water under UV light irradiation.     

Synthesis and characterization of poly（phthalazinone ether nitrile） （PPEN）-polydimethylsiloxane （PDMS） block copolymers

Block copolymers with different backbone compositions have been prepared by the condensation of dimethylamino terminated poly（dimethylsiloxane） （PDMS） and hydroquinone terminated poly（phthalazinone ether nitrile） （PPEN） in the presence of chlorobenzcne/N-methyl pyrrolidone （NMP） as solvents. The products were characterized by FTIR, ^1H NMR and gel permeation chromatography. Differential scanning calorimetry analysis indicated that the block copolymers showed separated microphase.     

Synthesis and properties of new block copolymers based on polydimethylsiloxane and tetraphenylethylene-containing polyimide

New polydimethylsiloxane (PDMS)-polyimide block copolymers were synthesized by the solution polycondensation of aminopropyl-terminated polydimethylsiloxane, 1,1-bis(4-aminophenyl)-2,2-diphenylethylene, and 3,3′,4,4′-benzophenonetetracarboxylic dithioanhydride in pyridine. New 1,3-bis(3-aminopropyl)tetramethyldisiloxane (BADS)-based random copolyimides were also prepared. The inherent viscosities of all the random and block copolyimides were in the range of 0.13–0.90 dL/g in N-methyl-2-pyrrolidone. These copolymers were soluble in N,N-dimethylacetamide, N-methyl-2-pyrrolidone, and m-cresol. All the BADS-based random copolymers and PDMS-containing copolymers with PDMS content above 42 wt % were soluble in tetrahydrofuran and chloroform. Transparent or somewhat cpaque films were prepared by casting from the reaction solutions. The BADS-based random copolyimides had one glass transition temperature (T_g) in the whole composition ranges, which showed single phase nature of the copolymers. On the other hand, the PDMS-polyimide block copolymers had double T_gS, indicating phase-separated morphology. The block copolymers containing PDMS content above 73 wt % behaved like a high temperature elastomer. © 1993 John Wiley & Sons, Inc.     

Synthesis and characterization of critical process related impurities of an asthma drug – Zafirlukast

Zafirlukast is an oral leukotriene receptor antagonist (LTRA) for the treatment of pulmonary disorders such as asthma. During the process development of zafirlukast, eight process related impurities were observed at a level of 0.1–0.15 area percent. Synthesis and characterization of these impurities and investigation of the root cause of their formation is described.     

Synthesis of polydimethylsiloxane microemulsions by self-catalyzed hydrolysis/condensation of dichlorodimethylsilane

The preparation of PDMS microemulsions was carried out by adding at controlled rate dichlorodimethylsilane (DCMS) in a solution of sodium dodecylpolyoxyethylene(8) sulphate. The instantaneous hydrolysis of DCMS and subsequent condensation of the corresponding dihydroxysilane generate dispersions of cyclosiloxanes of small lengths (4 to 6 D units). The high load of chloride ions released during the hydrolysis step requires the presence of the above-mentioned electrosteric surfactant to avoid rapid coagulation of the dispersion. In addition, its sulphate end-group captures a proton that catalyses the ring-opening polymerization of cyclosiloxane as well as the polycondensation of disilanol PDMS chains. Final particles exhibit a diameter of about 50 nm for a polydispersity index of less than 1.1. They are constituted of PDMS chains exclusively linear ( ; ) and of small cycles in low contents (less than 5 wt% in the best conditions). To cite this article: G. Palaprat, F. Ganachaud, C. R. Chimie 6 (2003).     

Synthesis of new polydimethylsiloxane-polyamide copolymers from phenylene-bis-5-oxazolones and aminopropyl-terminated polydimethylsiloxane oligomers

Alternating polydimethylsiloxane-polyamide block copolymers were prepared in dichloromethane or chloroform solution at room temperature from 3-amino-n-propyl-terminated polydimethylsiloxane oligomers and 2,2′-p-phenylenebis(4,4-dimethyl-5-oxazolone). Solution and thermal properties of the polymers were characterized.     

Synthesis of palladium colloids within polydimethylsiloxane and their use as catalysts for hydrogenation

The presence of unreacted silanes within cured polydimethylsiloxane (PDMS) leads to the reduction of tetrachloropalladate(II) ions, generating encapsulated palladium colloids. The resulting colloids had varied morphology and were typically less than 80 nm in size. The Pd/PDMS vessels, which contained 0.10±0.01% Pd, were effective catalysts for the hydrogenation of carbon-carbon multiple bonds for at least ten successive runs with no loss of catalytic activity, and the catalyst does not exhibit the same pyrophoric behavior as Pd on carbon after use in hydrogenation reactions. In addition, storage of previously used Pd/PDMS vessels for 6 months in air did not affect the catalytic activity, and the overall morphology of the catalysts after use was the same as those that have not been involved in catalytic reactions.     

Synthesis and characterization of a novel hydroxy terminated polydimethylsiloxane and its application in the waterborne polysiloxane–urethane dispersion for potential marine coatings

α‐Butyl ω‐N, N‐dihydroxyethyl aminopropylpolymethylhydrosiloxane (PDMS), a monotelechelic polydimethylsiloxane with a diol‐end group, which is used to prepare siloxane–urethane dispersion, was successfully synthesized. Then, novel silicone‐based polyurethane (PU)‐dispersion was prepared by the addition polymerization of hexamethylene diisocyanate, to PDMS, polyethylene glycol (PEG) and dimethylol propionic acid. The goal of this study was to explore the potential use of polysiloxane–urethane in marine coatings in order to boost the flexibility, adhesion, erosion and foul‐release property with respect to PDMS/PEG ratio (PDMS wt%). The PDMS was characterized by Fourier‐transform infrared (FT‐IR), proton nuclear magnetic resonance and carbon‐13 nuclear magnetic resonance spectroscopic techniques. The results showed that each step was successfully carried out and the targeted products were synthesized in all cases. The structural elucidation of the synthesized waterborne PU and waterborne polysiloxane–urethane (WBPSU) was carried out by FT‐IR spectroscopic technique. Thermal properties of the resins were studied by using thermogravimetric analysis and differential scanning calorimetry. The antifouling property of the coatings was investigated by the immersion test under a marine environment for 90 days. The fouled area was calculated for all the samples, and the fouled area (%) decreased with increasing PDMS content. After 90 days, the lowest fouled area (6%) was observed in the sample using WBPSU2 (PDMS 4.48 wt%) among all of the samples. Copyright © 2012 John Wiley & Sons, Ltd.     

Synthesis and characterization of three-coordinate and related beta-diketiminate derivatives of manganese,iron, and cobalt

Treatment of M[N(SiMe(3))(2)](2) (M = Mn, Fe, Co) with various bulky beta-diketimines afforded a variety of new three-coordinate complexes which were characterized by UV-vis, (1)H NMR and IR spectroscopy, magnetic measurements, and X-ray crystallography. Reaction of the beta-diketimine H(Dipp)NC(Me)CHC(Me)N(Dipp) (Dipp(2)N(wedge)NH; Dipp = C(6)H(3)-2,6-Pr(i)(2)) with M[N(SiMe(3))(2)](2) (M = Mn or Co) gave Dipp(2)N(wedge)NMN(SiMe(3))(2) (M = Mn, 1; Co, 3) while the reaction of Fe[N(SiMe(3))(2)](2) with Ar(2)N(wedge)NH (Ar = Dipp, C(6)F(5), Mes, C(6)H(3)-2,6-Me(2), or C(6)H(3)-2,6-Cl(2)) afforded the series of iron complexes Ar(2)N(wedge)NFe[N(SiMe(3))(2)] (Ar = Dipp, 2a; C(6)F(5), 2b; Mes, 2c; C(6)H(3)-2,6-Me(2), 2d; C(6)H(3)-2,6-Cl(2), 2e). This represents a new synthetic route to beta-diketiminate complexes of these metals. The four-coordinate bis-beta-diketiminate complex Fe[N(wedge)N(C(6)F(5))(2)](2), 4, was also isolated as a byproduct from the synthesis of 2b. Direct reaction of the Dipp(2)N(wedge)NLi with CoCl(2) gave the "ate" salt Dipp(2)N(wedge)NCoCl(2)Li(THF)(2), 5, in which the lithium chloride has formed a complex with Dipp(2)N(wedge)NCoCl through chloride bridging. The Fe(III) species Dipp(2)N(wedge)NFeCl(2), 6, was obtained cleanly from the reaction of FeCl(3) with Dipp(2)N(wedge)NLi. Magnetic measurements showed that all the complexes have a high spin configuration. The different substituents in the series of iron complexes 2a-e allowed assignment of their paramagnetically shifted (1)H NMR spectra. The X-ray crystal structures 1-2d and 3 showed that they have a distorted three-coordinate planar configuration at the metals whereas complexes 4-6 have highly distorted four-coordinate geometries.